Firewire drive does not sleep when iMac sleeps

My G-Tech G-Drive Mini connected via Firewire to an new iMac will not spin down when the iMac goes to sleep. It does spin down with the iMac active, but will spin up when the iMac goes to sleep. On a MacBookPro with Tiger, the drive will spin down when the Mac sleeps, which I would expect to be the "normal" behavior for an external drive. Is this a Drive issue or an iMac Firewire bus issue?

By the way Bosanac...
Welcome to the Apple Discussions!
It seems as though I had a similar issue with my ministack external drive and I stopped using it and I have used several different external drives with all my Mac including my iMac. It's definitely hard to say as I would lean more towards the G-drive. I would contact G-Technology and see if they have nay suggestions.
Keep in mind that there have been many issue with OSX SL and that too maybe an issue.

Similar Messages

  • My external hard drive does not show when I am trying to open a document in Office Org??

    My external hard drive does not show when I am trying to open a document in Office Org?? When looking in the about IMAC system support it shows as being connected. Any ideas??

    Does the drive show up under 'Devices' in Finder?

  • External Firewire drive does not mount on desktop now.

    Greetings everyone.
    G5 dual, 4.6GB ram, OSX 10.4.10, external firewire drive, formerly worked fine, now is invisible.
    Not the drive. New purchase, worked fine until a restart. Not the cable. Power is getting from the G5 to the firewire drive. Not the port. I also have a firewire card instlaled so I have three ports to connect it to (and two on the FW drive). No combination works. Not the computer, the FW drive also fails to appear on an iBook. Not the OS. I did a clean install to make sure.
    I'm not a newbie. I know what I'm doing. Until now! DiskWarrior, TechTool Pro, Drive Genius and Apple's Disk Utility cannot see the drive.
    The FW drive is a Powerbook internal HD inserted into a case, purchased seperately.
    At my wits' end. Can anyone help please.

    I am suddenly having this EXACT problem. I have two Firelite firewire drives (one 60G and one 80G) that are suddenly refusing to mount on my older dual 1.25GHz G4 tower. They are also suddenly refusing to mount on my non-intel iMac. They will both mount painlessly on my new Intel MacBook Pro, but that's not much use, since the point of the firewire drives is to transfer files between these computers. I'm updating all of them to 10.4.10 to see if that's the issue...

  • Trying to make RAID boot drive - but drive does not appear when starting up

    Used Disk Utility to take current boot drive and put it in mirrored RAID. Did this by taking volume, placing it in RAID window, and clicking "enable".
    The new drive is shown as bootable, and selectable by Startup preferences but does not work. When I hold Option key during startup, the RAID drive does not show up. Apple support offered no help and said I should get hardware card. (Will add second drive after RAID is bootable).
    The 'virtual' disk for the RAID drive (disk4) seems to not be visible.

    Howdy bhagon,
    It sounds like the iPhone is not recognized in iTunes. Allow me to recommend this troubleshooting assistant named:
    iPhone not appearing in iTunes
    http://www.apple.com/support/iphone/assistant/itunes/
    Start at step 1 and work your way down as needed. Here is that step 1 to get you started:
    Update iTunes
    Make sure you have the latest version of iTunes. To check for available updates of iTunes on a Mac, go to iTunes > Check for Updates. On Windows, go to Help > Check for Updates.
    To install iTunes, you need one of the following operating systems on your computer:
    Mac: OS X version 10.6 or later
    PC: Windows 7; Windows Vista; or Windows XP
    Note: If you are using a 64-bit version of Windows 7, be sure to download the 64-bit version of iTunes.
    If your computer does not meet these requirements, you may need to upgrade your computer before installing iTunes.
    Thank you for using Apple Support Communities.
    Regards,
    Sterling

  • Booting from firewire drive does not recognize existing users.

    Hello,
    I just bought a Lacie firewire drive to have a bootable backup of my Macbook internal drive.
    I used SilverKeeper 1.1.4, that comes with the drive, to make a bootable copy.
    The copy is bootable but when Tiger startus up fro the firewire drive I get the presentation video and am asked to setup the system including creating a new user.
    It is as if the existing Users directory, that was copied, is not recognized by the clonned system.
    Running Tiger 10.4.11
    Any ideas?
    Joaquim

    I think this was driver issue

  • USB Drive does not work when connected to Airport Extreme

    I had an external drive connect directly to my iMac and recently purchased an Airport Extreme. When I plugged it into the USB point on the back of the AX has an odd name and won't allow access. When it was configured directly to my iMac it was named TheVault, now it is TheVault???. When I try to access via Go>Network in finder menu, I get "The operation cannot be completed because the original item for "TheVault??? cannot be found." Another detail if found in the GetInfo it that it shows 0kb available. All things point to it's existence as a drive but it has no access to the data that was clearly there when it was plugged into the back of the desktop. Jack sends.

    TheWack wrote:
    I had an external drive connect directly to my iMac and recently purchased an Airport Extreme. When I plugged it into the USB point on the back of the AX has an odd name and won't allow access.
    Did you use AirPort Utility to enable disk sharing?

  • Thunderbolt to firewire adaptor does not work when daisy chaining firewire devices

    Hi,
    I just purchased the Thunderbolt to firewire adaptor for my new late 2012 iMac.
    It works when connecting a single firewire device, but when I daisy chain another drive, the first drive disconnects and nothing mounts.
    I am trying a Hitachi G-Raid and a couple of WD My Studio II hard drives. They all work when connected directly to the adaptor, but not when more than one drive if daisy chained with firewire.
    Has anyone got firewire daisy-chaining working with a thunderbolt adaptor? (just to clarify I am not refering to thunderbolt daisy chaining, as the adaptor is an end-of-chain thunderbolt device).
    Thanks

    Yikes, that's sad to hear.
    I can't test it, no TB here, but are all these drives self AC powered, ie. no bus powered drives?

  • Audio Driver does not load when computer is powered up

    I have a HP Pavillion Elite Model 9600t desktop PC that I bought from the HP on-line site in June of 2009.  This system is running Windows Vista Home Premium 64 bit edition. 
    No audio card, using the mother board on board audio with powered HP speakers connected to the Green connector on the mother board.
    Problem:
    When the system is initially powered up, it boots ok, but when the desktop is displayed I get the "No Audio Device is Installed" error message displayed on the lower tolbar speaker ikon.
    I can then load the "Realtek High Definition Audio" driver using the  recovery manager and restart the system with powering down, and everything will then work ok, untill the system is powered off, then the problem repeats the next time the system is powered up.
    The sound playback window under the control panel shows the speakers as  "Realtek High Definition Audio Working, but the "Set Default" button at the bottom of the window is greyed out and not functional.
    Any guidance would be appreciated

    I have a HP Pavillion Elite Model 9600t desktop PC that I bought from the HP on-line site in June of 2009.  This system is running Windows Vista Home Premium 64 bit edition. 
    No audio card, using the mother board on board audio with powered HP speakers connected to the Green connector on the mother board.
    Problem:
    When the system is initially powered up, it boots ok, but when the desktop is displayed I get the "No Audio Device is Installed" error message displayed on the lower tolbar speaker ikon.
    I can then load the "Realtek High Definition Audio" driver using the  recovery manager and restart the system with powering down, and everything will then work ok, untill the system is powered off, then the problem repeats the next time the system is powered up.
    The sound playback window under the control panel shows the speakers as  "Realtek High Definition Audio Working, but the "Set Default" button at the bottom of the window is greyed out and not functional.
    Any guidance would be appreciated

  • External drive does not show on iMac

    it showed up once & now doesnt work new intel imac. It shows on my macbook pro fine. help!

    Finder > Preferences > General Tab > check External disks

  • External hard-drive does not reconnect after sleep

    Hi everyone
    I am trying to use my Energy Saver to SLEEP my iMac after 1 hour. It goes to sleep no problem, but on wake-up, my external USB hard drive does not reconnect. There is also an error message that I didn't disconnect the drive properly. I fear this may be one of Mac OS X's "features". Has anyone encountered the same thing?
    On a side note, I also find that my USB keyboard does not always reconnect as well. I use a windows USB mouse that I have connected to wake it from sleep, however my USB keyboard (the small one for Macs), sometimes does not allow me to type unless I unplug it and back in.
    Another point of note is that both the HD and the keyboard are connected to the iMac through a 7 port USB hub.

    r_dizzle wrote:
    Another point of note is that both the HD and the keyboard are connected to the iMac through a 7 port USB hub.
    I think this might be the issue. If the iMac is waking back up, it will likely be waking up this HUB, but the HUB might not be re-initialising the connection between OS X and the external drive or the keyboard.
    After waking the iMac, if you unplug the external drive from the HUB, then plug it back in again, does OS X pick it up again? Have you tried plugging the external drive directly into the iMac and then testing what the result is?
    If you read back on what you've said, you pointed out that you have a USB mouse that you use to wake the iMac from sleep. Is this mouse directly connected to the iMac? If so, it surely can't be a coincidence that a directly connected USB device can wake the iMac from sleep, but any USB devices connected to the iMac via a USB HUB cannot.
    I would suggest you test the drive as it is directly connected to the iMac. I would complete the same test with the keyboard too. I think you'll find it's the USB HUB.
    I hope this helps.

  • IMac 10.5 does not sleep

    My iMac does not sleep. The display does go to sleep but the computer itself does not, and as a result heats up like none other. Any help?

    What all USB or Firewire devices are connected?
    Get Temperature Monitor to see if it's heat related...
    http://www.macupdate.com/info.php/id/12381/temperature-monitor
    iStat Menus...
    http://bjango.com/mac/istatmenus/
    And/or iStat Pro...
    http://www.islayer.com/apps/istatpro/

  • Since I installed Lion on my macbook the LED light does not pulse when I close the screen - the sleep function does not work.

    Since I installed Lion on my macbook the LED light does not pulse when I close the screen - the sleep function does not work neither when chosen after pressing the button nor chosen in the apple menu..

    I have had the same problem but on another forum it was suggested that disabling internet sharing would solve this. This fix seems to work on my machine - why it works I do not understand

  • Bue tooth is dead, and computer does not sleep when i close the screen now.

    OK
    This is a on going issue:
    1-I paid for apple care 4 days prior to the expiration of my one year agreement with purchase, they shipped it a day after it expired of course, and at first it rejected my serial number saying it was beyond the date,
    2-i contacted Apple, they fixed this and after calling them again they repeated the same thing, i can not down load techtool deluxe.
    3-However, i used iMac apple care kit to download the latest Techtool deluxe only to find out it is not Leopard Compatible,
    Apple did it again with a new OS, releasing it with no coverage leaving us all sitting around like PC geeks !
    Now after several incidents with blue-tooth on the phone with tech support, like been told i have to pay money if its the OS doing this instead of the hardware itself, i am a bit fed up here., blue-tooth is dead and my macbook does not sleep, i can even see iChat still on while the screen is closed!
    I no longer have confidence i the idea of going back to Tiger on this computer will fix a bad logic board as i read others with the similar BT problem.
    Can anyone advise what to do next please?

    used original dvds and found BT, LEOPARD bugs caused the BT problems.

  • X120e does not sleep when lid closed

    I found another similar post, however it was resolved by the individual reinstalling the operating system.
    My issue is more complicated. I have made sure everything is up to date, all the settings that tell the system to sleep when the lid is closed are turned on. I have even turned those settings off off, just so I could turn them back on to make sure there wasn't something quirky about it.
    I have tried restoring the system to factory settings using the recovery partition, as well as discs burned from the program that came with the computer. I have tried clean install from Windows 7, 8, and 8.1 discs.
    The unit still does not sleep. I don't ever remembering it being able to. I once closed the display thinking it would sleep (power was plugged in). Woke up the next day, went to work for 8 hours, came back and felt that the system was really hot. Opened the lid and the screen was exactly as I had left it the day before.
    When I first got the system in 2012, the screen did not work, so I actually had to send it to Atlanta, GA for repairs. It came back quickly, and it still did not work, so I actually sent it back to Atlanta, GA's repair center a second time in the same week. It came back working and I left it alone. I never tested the sleep/wake because I always just turned the system off when I was done with it, but now I am back in school and this little computer comes in handy, but I don't want to turn off the system manually going from class to class when I need to pack it away in my bag.
    Could there be a hardware issue? Something inside not connected? This laptop works perfectly EXCEPT for the fact that it will not sleep when the lid is closed. It is out of warranty but had I known this was an issue while it was still under warranty, I would have inquired. This unit is in pretty fantastic shape, looks brand new too. No damage, never been dropped, and only ever handled by me (never loaned out).
    How can I fix this?

    Thanks for the reply, gat0gelat0.
    Yes, those settings were the first things I checked. I also tried changing it to "Do nothing", then changing back to the sleeping option. It still does nothing when I close the lid.
    I would like the functionality of it going to sleep when I close the lid for the convenience, like when class ends, I have to rush to my next class, I just want to close the lid, put it in my bag and run to the next class. Keyboard shortcuts like Fn-F4 work, but this laptop should have the functionality I am describing, and I want to figure out why it isn't working and how to fix it.
    I suspect there is an issue with whatever is used hardware wise to sleep the machine. Either it's not being triggered, or it's not there, or it's broken. I've tried running a magnet around the bezel of the LCD screen as well as around the palm rest bezel and there is no activity as I've read that many laptops trigger sleep by interaction by a magnet. Still nothing.

  • HT1776 MacBook does not sleep when closed

    I have a Late 2013 Retina Macbook Pro running Mavericks.  Sometimes when I close the lid, it does not sleep or turn off the display, even after the set time in Energy Saver preferences.  My main concern is that I have my security settings set to lock my computer 5 seconds after sleep/turning off the display, and this does not happen, as it does not go to sleep.  The only way I notice is that when I open the computer some time later, the screen is already on and it is not locked.  There are no periphials connected when this happens.

    Sleep - Why your Mac might not sleep or stay in sleep mode
    Sleep - Won’t

Maybe you are looking for

  • BPEL Process with multiple file types using one FTP adapter is not working

    i created a bpel process which will fetch the files from remote location using FTP adapter. Now the process works for only one format or file type like *.xls. How can i use more than one file format in one FTP adapter. OR is there any other way to do

  • 100% height not working in Internet Explorer

    I'm using the following CSS code to have a verticle div tag stretch down the left side: }#leftbar { background-color: #2E4A72; height: 100%; width: 180px; border-right-width: 1px; border-right-style: solid; border-right-color: #FFFFFF; position: abso

  • My Computer Gets Hot To 90 C, Is It Because of my Case!?

    Why does my computer get hot when I'm on Safari, Minecraft or any other iApps?

  • Launching Photoshop Elements 12 Organizer

    Getting an error message when trying to launch Elements 12 Organizer on MacBook Pro 10.6.8.  Elements 12 Editor is working fine.

  • Se cess tab is missing

    Hi, we  installed sap in our company (ecc6.0) recently.. when we are working in our Ides, while doing migo for excisable item, all the values has flowed correctly in part 2 accounitng view.. But there is no sec cess tab, as well the se cess values no