Firewire not reading

My fire wire just quit on me? It won't read my external hard drives My Hard drive works via usb but not 1394. Any help would be appreciated.
Than you

What to do if your computer won't recognize a FireWire device
http://docs.info.apple.com/article.html?artnum=88338
 Cheers, Tom

Similar Messages

Firewire. Not reading device.

Hello. I had a question as to how would you know if your firewire port is damaged (hardware) or if it is a software issue. I have a Apogee Duet that connects through firewire. The device lights up so I know there is power going to it, but once plugged in, my computer does not read it.
I have tried restarting and reinstalling the software but still no luck. Does anyone have any advice?
Thank you.
Also, I have read somewhere that you can reset a certain type of memory that is associated with firewire. What I took from the reading was to basically restart the computer. Anyone know?

USB and FireWire Quick Assist
http://support.apple.com/kb/HT1151?viewlocale=en_US
What to do if your computer won't recognize a FireWire device
http://docs.info.apple.com/article.html?artnum=88338
Dealing with FireWire problems (drives not mounting, devices unrecognized, etc.)
http://www.macfixit.com/article.php?story=20041221081432908
 Cheers, Tom

Help required please. "Itunes can not read the contents of my iphone"

Greetings all,
I know this question has been asked before and I apologize for asking again but all the solutions provided don't seam to work for me, can anyone help me please.
I am receving the message: "Itunes can not read the contents of the iPhone. Go to the summary tab In iPhone Preferences and click restore torestore this Iphone to factory settings".
Now a little about my iphone, Itunes and my laptop and what steps i havealready tried.
I have an iPhone 4 running software 5.0
My itunes version is 10.5.0.142
I know these are not the most up to date versions but I have had this issue for almost 3 months now and updating the software back then was the first step I tried. I don’t believe updating to the latest will fix this issue as updating the last two times did nothing.
Every so often after starting Itunes, The program will stop responding and will require the three finger death kill (CTRL, ALT, DELETE) to open task manager to end the task of Itunes. Once it shuts down, I restart the iTunes and it runs smoothly, apart from not reading my iPhone.
When I run a diagnostic in itunes under the help tab, I get these fail messages:
Network Connectivity test: Secure link to Itunes store fail
Device connectivity test: Under support services: Itunes helper is not running. And under ports: No iPod, iPhone or iPad found.
Device Sync test: No iPod touch, iPhone or iPad found.
*See below for full diagnostic report*
I have restored back to factory settings twice.
I have shut down and restarted both my iPhone and laptop.
I am running Windows 7 32-bit on my laptop.
I am using ZoneAlarm as my fire wall, and have been disabling it when syncing my iPhone to prevent other error messages.
The iPhone is plugged into a genuine Iphone USB cable and is plugged into a USB port not a USB hub on my laptop, I have tried plugging it into all 4 USB ports and this issue still persist. The Cable is less then 5 months old, is not frayed or damaged in any way, have also borrowed 2 other cables from friends and still the same issue.
The iPhone does not even come up in windows explorer as a digital camera.
The iPhone is NOT jailbroken
I do not live close to a so called genius bar, however I have made the journey to them on 3 separate occasions last year when I first received my iPhone for a different issue, the so called genius's could not fix the problem so they just gave me a new (refurbished) iPhone, which did not extend my warranty. I will not be taking the iPhone back to them as I believe they can not resolve many issues, this is why I am reaching out to the power of the people in the wider apple community.
I have read in other forums about ifunbox and other programs for jail broken iPhones to isolate folders “iTunesDB” and "iTunesCDB" and delete them. If this is the issue is there a way to access these files through windows explorer as my iphone is not jailbroken.
I hope I have provided enough information and someone can help me fix this issue. If I have left anything out, please let me know. I thank everyone in advance for your patience and support.
Thanks
Hoggie27
FULL DIAGNOSITC REPORT
Microsoft Windows 7 Home Premium Edition Service Pack 1 (Build 7601)
Hewlett-Packard HP Pavilion dv6 Notebook PC
iTunes 10.5.0.142
QuickTime not available
FairPlay 1.13.35
Apple Application Support 2.1.5
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 4.0.0.96
Apple Mobile Device Driver 1.57.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.3.494
Gracenote MusicID 1.9.3.106
Gracenote Submit 1.9.3.136
Gracenote DSP 1.9.3.44
iTunes Serial Number 001BAD14XXXXEA78
Current user is an administrator.
The current local date and time is 2011-11-16 10:04:53.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce GT 230M
**** External Plug-ins Information ****
No external plug-ins installed.
The drive H: Vodafone USB SCSI CD-ROM Rev USB is a USB 1 device.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name:    {97524DB0-B9DC-41DB-8AFA-0CE6938F7C95}
Description:    PC
IP Address:    (HAS BEEN REMOVED FOR PERSONAL REASONS)
Subnet Mask:    255.255.255.255
Default Gateway:    0.0.0.0
DHCP Enabled:    No
DHCP Server:
Lease Obtained:    Thu Jan 01 11:00:00 1970
Lease Expires:    Thu Jan 01 11:00:00 1970
DNS Servers:    10.143.147.147
        10.143.147.148
Adapter Name:    {BFF0456E-DE42-4FEF-B1FA-1EA1C5EDEE42}
Description:    Vodafone Mobile Broadband Network Adapter (ZTE)
IP Address:    0.0.0.0
Subnet Mask:    0.0.0.0
Default Gateway:    0.0.0.0
DHCP Enabled:    No
DHCP Server:
Lease Obtained:    Thu Jan 01 11:00:00 1970
Lease Expires:    Thu Jan 01 11:00:00 1970
DNS Servers:
Adapter Name:    {D5511FFD-0CA8-4F62-B3CA-E90384FFCD03}
Description:    Broadcom 43225 802.11b/g/n
IP Address:    0.0.0.0
Subnet Mask:    0.0.0.0
Default Gateway:    0.0.0.0
DHCP Enabled:    Yes
DHCP Server:
Lease Obtained:    Thu Jan 01 11:00:00 1970
Lease Expires:    Thu Jan 01 11:00:00 1970
DNS Servers:
Active Connection:    PC
Connected:    Yes
Online:        Yes
Using Modem:    Yes
Using LAN:    No
Using Proxy:    No
SSL 3.0 Support:    Enabled
TLS 1.0 Support:    Enabled
Firewall Information
Windows Firewall is on.
iTunes is NOT enabled in Windows Firewall.
ZoneAlarm Firewall is installed.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was successful.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was unsuccessful.
The network connection timed out.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-11-16 09:59:57.
**** CD/DVD Drive Tests ****
LowerFilters: Afc (1.0.0.2),
UpperFilters: GEARAspiWDM (2.2.0.1),
F: hp CDDVDW TS-L633N, Rev 0300
Drive is empty.
**** Device Connectivity Tests ****
iPodService 10.5.0.142 is currently running.
iTunesHelper is currently not running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) 5 Series/3400 Series Chipset Family USB Enhanced Host Controller - 3B34. Device is working properly.
Intel(R) 5 Series/3400 Series Chipset Family USB Enhanced Host Controller - 3B3C. Device is working properly.
FireWire (IEEE 1394) Host Controllers:
1394 OHCI Compliant Host Controller. Device is working properly.
Most Recent Devices Not Currently Connected:
iPhone 4 (GSM) running firmware version 5.0
Serial Number:    85107XQLA4S
**** Device Sync Tests ****
No iPod, iPhone, or iPad found.
< Edited By Host >

Hi AM_Kidd.
Thanks for your reply.
I have done a complete uninstall and re install of iTunes and all related apple programs from my laptop through control panel, add remove programs and also by going through program files and deleting all tracers of any left over folders remove programs may have missed.
My apologies for forgetting to add this in my original post.
Thanks again

Firewire not detected...

I plugged my external hard drive via fire wire into the back of my mac pro.
I plugged my Panasonic mini-dv camera into the front. When I boot up FCP, the computer/program doesn't recognize that a video device is plugged in.
Any way to activate that fire wire port on the front of the computer?

Any way to activate that fire wire port on the front of the computer?
It probably is activated. Try plugging your external hard drive to the front port.
If it works, then you know the problem is not the port.
Once you've determined that the port works, plug your camera into it.
Make sure the camera is in playback (VCR) mode, not camera mode.
As Nick suggests, you might need to try another cable.
In FCP, it may be necessary to choose an appropriate setup.
If you select Audio/Video Settings (command-option-Q),
you'll see tabs for Capture Settings and Device Control Settings.
Normally, these should be NTSC (DV and Firewire, respectively).

URGENT FIREWIRE NOT DETECTED

Hi.
I've just bought a new intel iMac 2.66ghz and installed FCS.
I just attempted to capture from a dv tape for the first time and it came up with the message...
"unable to initialize tape deck, you may still log offline clips or use capture now"
when i attempt to use capture now it says..
"attempt to capture video without a video device selected. please select a video device in your capture presets and try again"
I have the capture settings set to Firewire PAL DV PAL 48khz Anamorphic
I am capturing off of a Panasonic NV-GS320 - I've captured off of this camera onto an iMac in the past (a white one, I'm assuming it was not an intel based)
When i try and check if the camera is detected in the system profiler it says "unable to list firewire devices" next to the word 'warning'
However when i have no firewire cable inserted it says nothing except the max speed.
Is my firewire not being detected or is faulty?
Can anyone help me please!? I have a project due in that i need to start but i cannot capture!
Any help would be Much appreciated

Have you done all of this:
In the FCP menu bar, go to Final cut Pro > Easy Setup. Choose DV PAL. Click OK.
Go to Sequence > Settings and click on "Load Sequence Preset". It will already be set to DV PAL, confirm by clicking OK. Make a new project file with these settings. Try capturing your material again.
What version of Final Cut Pro are you using ?

G5( DVD SP4) WILL NOT READ AC-3 Files

I have spent more time and read more papers on Compressor and DVD P4 than on any other Apple software.
I have encoded from FCP4.5 a 27 min project using compressor, all the settings seem fine and the visuals are good.
I import the assets into DVD 4 and they import all ok and I get green lights on the asset log etc.
In the timeline the visuals are ok but I cannot get the ac-3 Dolby to read at all.
I have imported the pcm sound directly into DVD and it works fine as do Aiff files.
I have updated all my software to check I have all the codecs etc and all is up to date.
I have re-encoded the sound again and checked all the settings and the same thing happened. DVD S is not reading the dolby sound.
The data seems to be there ok but the silence is deafening!!
Confused Mick in Belfast
G5 Dual Processor Mac OS X (10.4.4) 140G Lacie Ext Firewire HD

How are you monitoring your audio? Analogue or SP/DIF (optical output).
Have you set your audio output preferences in the SImulator tab of your DVDSP preferences?
Check your audio output settings in your "Audio MIDI Setup" utility as well.

I have an imac 2009 the disk drive is damaged and I have lost the passwords I need to reset passwords I tried booting with a macosx disk from an external hard drive but did not read the drive how else can I reset password ?

I have an imac 2009 the disk drive is damaged and I have lost the passwords I need to reset passwords I tried booting with a macosx disk from an external hard drive but did not read the drive how else can I reset password ?
I have a 2012 mac book pro can I use that to connect with firewire and load osx that way? and how woudl I do that?
Thanks so much!

To what password are you referring? Do you mean your user account's admin password? Or do you mean the master password for File Vault or do you mean a Firmware Password?
For an admin password:
Forgot Your Account Password
For Snow Leopard and earlier
     Mac OS X 10.6- If you forget your administrator password
For Lion/Mountain Lion
    Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
     When the menubar appears select Terminal from the Utilities menu.
     Enter resetpassword at the prompt and press RETURN. Follow
     instructions in the dialog window that will appear.
     Or see Reset a Mac OS X 10.7 Lion Password and
     OS X Lion- Apple ID can be used to reset your user account password.
If you cannot do the above then try this:
1. Boot to Safe Mode by restarting and after the chime press and hold down the COMMAND-S keys until a black screen with white type appears.
2. At the prompt, type the following commands pressing return after each command line:
     /sbin/fsck -yf
     If you do not receive a "Filesystem OK" message then repeat this command until
     you do. If after seven tries you still do not receive a "Filesystem OK" message,
     then the system is corrupted and needs to be reinstalled.
     mount -uw /
     cd /private/var/db/netinfo
     mv local.nidb local.old
     rm ../.AppleSetupDone
     shutdown -r now
The second-to-last command above will cause OS X to think that the operating system is newly installed, and when the new owner starts up the computer it will send him/her to the startup wizard where he/she can start a new user without reinstalling.
This last method does not actually change a password. It simply removes the user accounts and lets you create an initial admin account as if the computer were new out of the box.
How to reset the OS X password without a startup CD:
Reboot into Single-user Mode. Enter the following and press RETURN after each command line
   1. Type fsck -fy
   2. Type mount -uw /
   3. Type passwd <username>
I have never tried this method myself.

EMac ejects CDs, will not read them

Hello!
I have an eMac that, it seems whatever I do, will not read discs. The disk I am working with is a Leopard install disc/DVD, but it is not the only one that does this problem. It appears to spin for a few seconds in the CD/DVD drive, then ejects it. I have tried getting it to work in Safe Mode, resetting the PRAM, and currently I am attempting to clean the drive using a compressed air duster.
My eMac, bought from eBay many years ago, is an educational model, with 1 GHz processor, an upgraded 1 GB of RAM (it appears to have originally come with 512 MB, according to the DVD drive door), and the ATI Radeon 9200 Graphics.
Any help would be appreciated! Thank you!

That indeed is a special eMac version sold only to educational institutions. The good news is that it was based on the newer USB 2.0 logic board and, in spite of Apple's outdated specs, can handle up to 2GB RAM and, of course, has USB 2.0. The ATI 9200 video chipset clearly makes it as variant what Apple called a "eMac (USB 2.0)" with the model identifier "PowerMac6,4." The commercial model had a 1.25gHz processor; the 1gHz was used in the edu-model to reduce costs.
The bad news is that, although I cannot find it in the limited specs published for this special model, another cost saving measure Apple had applied in other edu-model Macs was to downgrade the optical drive, so I would not be surprised if yours has a CD or CD-R optical drive. The commercial model typically had a "Combo" drive, capable of read/write with CDs and read-only for DVDs.
The check BDAqua posted will tell you for sure.
Many 1.0 and 1.25ghz USB 2.0 models had a bad logic board problem. The affected units fell in these serial number ranges:
G8412xxxxxx- G8520xxxxxx
YM412xxxxxx - YM520xxxxxx
VM440xxxxxx - VM516xxxxxx
If yours in in one of those ranges but is still working after all these years, it is probably OK.
As for the DVD instal disk, Leopard 10.5 was available on CD on special order. If you are in the US, I'd phone the central Apple Store (1-800-MY-APPLE) and ask for an operating systems specialist. Tell them you bought a DVD retail install disk but need the CD version for the older model Mac. That may still be able to arrange an exchange so you have compatible discs.
If you have a newer Mac with a working DVD-capable drive, you may be able to use FireWire Target Disk Mode to mount the eMac's hard drive on the newer Mac and then put your current install DVD in the new Mac but point the installer to the eMac. I've done that before, but I have piles of Macs from different eras.

EMac External LACIE DVD Drive not reading.

eMac External LACIE DVD Drive not reading.
eMac 700 MHz running OS X 4.4
Came without DVD or modem internal
Has 256mb memory
Bought a used Lacie 1394 Firewire DVR External.
Was able to burn DVD’s and CD’s with Toast 6 Light.
Cannot find the “DVD Player” on the hard drive.
It will read data DVD.
eMac will not read any movies burnt or bought.
I was told I probably need more memory?
Thought running IDVD would fix the problem.
No Soap.
This machine was giving external modem problems before Tiger was installed.
Before we spend more money or just get ride of the eMac.
What is the DVD problem?
This same Lacie burner reads and writes DVD and CD fine with our iMac 450 DV 320mb memory. Running 9.2 and X.3

OS X 10.3.x / 10.4.x natively support data burning to external DVD drives but video payback requires software such as iDVD which isn't installed by default on models without an internal DVD drive (the installer sees no internal drive and thinks it's unnecessary). Try downloading VLC Player and see if that will let you play movies.

G4 eMac will not read OS X v 10.4 disc

Hi All
I ahve a eMac G4 700MHz with combo drive and I'm trying to put OSX v 10.4 on to it but the combo drive will not read the disc. I can put a DVD (film)in and watch that and it will also play CD's.
On trying to get the drive rto read the disc, the system hangs and I get this message on the screen:
panic(cpu 0 caller 0x002E0C68): Unable to find driver for this platform: "PowerMac4,4".
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x002E0C68 0x002BFFF4 0x002BFDBC 0x002C0824 0x002C0E90
0x000A9894
Proceeding back via exception chain:
Exception state (sv=0x00525A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernal version:
Darwin Kernal Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70j~1/RELAESE_PPC
No debugger configured - dumping debug information
MSR=00001030
panic(cpu 0 caller 0x002E0C68): Unable to find driver for this platform: "PowerMac4,4".
Latest stack backtrace for cpu 0:
Backtrace:
0x00095718 0x00095C30 0x0002683C 0x002E0C68 0x002BFFF4 0x002BFDBC 0x002C0824 0x002C0E90
0x000A9894
Proceeding back via exception chain:
Exception state (sv=0x00525A00)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernal version:
Darwin Kernal Version 8.6.0: Tue Mar 7 16:58:48 PST 2006; root:xnu-792.6.70j~1/RELAESE_PPC
panic: We are hanging here........
So, that the message that I get. Can go no further with installing disc. Apple support say it's a memory problem?? Could it be.
Any help please............
Regards
Lee
iMac 17inch Duo 2GHZ Mac OS X (10.4.8) Have got an eMac G4 as well

Hi All
Still got the problem. I don't think its the drive,
because it plays DVD's CD's etc, even the disc's from
the Mac magazines. The DVD seems clean. I've run a
disc cleaner in the drive. Still no joy.
I can start the eMac up and it will boot up OK - OS X
10.2.8 The drive will read the DVD, as I can see the
'Max OS X Install DVD' window open up with the
install icon in the centre of the screen.
What about copying the DVD on to en external drive
and the trying to install from that. Would it work??
Thnks for your help, so far.
Regards
Lee
iMac 17inch Duo 2GHZ
Mac OS X (10.4.8) Have got an eMac G4 as
well
Hi Lee
Had exactly the same when attempting to update eMac to 10.4, very interesting.
Had to use a faster drive, as the one in my eMac was reading the 10.4 dvd too slowly.
Nothing wrong with disc, nor drive except it was too slow.
if you have a hard drive in bootable firewire external box and copying disc across to it doesnt work, (probably wont) then try borrowing a 2005 era or later dvd drive and using that in the external box.
For the purposes of the excersize, it wont matter if the dvd drive is not supported for burning (least mine isnt) so dont let that put you off having a go.
If all else fails, talk to Apple to see what their techs can do. (Apparently there is a service which supplies 10.4 on CD Rom. And they might be able to load from the DVD for you. They can put in a faster drive. Dont know about the price of that.
Paul

Tecra 8200: drive will not read DVD-R or DVD+RW

I have a Tecra 8200 running on Win98.
It has an SD-R2002 Rev A combo drive with firmware 1324.
It reads commercial DVDs OK, but will not read DVD-R or DVD+RW (booktype set to DVD-ROM) disks (I don't have any other types to try).
Is this correct or is the drive faulty?
If it is broken I would like to replace it with a DVD writer. Is there a writer that will fit this laptop?

The drive is not faulty. It is just DVD-CDRW drive, as Gipsy said.
I didnt find any info about compatible DVD burner for this unit. Problem is that this unit has no firewire or USB 2.0 ports and you can not even use external one. Maybe if you use USB 2.0 PCMCIA card.
The unit is about 5 or even 6 years old and you maybe expect too much. ;)

WD MyBook Premium 320GB Firewire not recognized on my MBP?

Hey guys,
First off, thank you for the help anyone is willing to offer.
Ok, so i have a MBP Intel Core Duo (1gb RAM) and use it to record music on. But basically, i have a WD MyBook Premium 320GB drive that works perfectly fine via USB. It powers up, mounts, and i can back anything i want on it. I formatted the drive to Mac Extended Journal format.
I would like to use the firewire port though, just to keep my USB ports open. When i plug it via Firewire i get nada. I plug it in and power up the MBP and the drive doesnt power up, so i turn it on and it doesnt mount. Now, THis is the second one i have, i had the same one a few weeks ago and returned it for this one thinking the drive was defective but its obviously not. is there anyway to "turn on" or Fix this issue with the firewire not recognizing the drive?
thanks alot for the help
Macbook Pro 15" Intel Core Cuo Mac OS X (10.4.9)

Ace King, in case you're still dealing with this I figured it out:
I called tech support for an hour. First lady I talked to told me the firewire cable that was supplied with the drive is defective (she knew the problem right away). Tried my own cable but it still didn't work. She put me on to "Level 2"....ooooooh....now I'm getting somewhere? No, wait for 15 more minutes listening to terrible muzak...
Anyways while I was waiting I thought I'd try my good cable in the other port on the drive and oila! So when the dude gets on the phone I ask him what the deal is...get this:
"The faulty cable most likely fried the port." Wow...not only is the cable crap it actually destroys their product...someone must have lost their job for that one. Seems like sabotage almost...anyways, there you go. Return it and DO NOT use the cable supplied.
Cheers!

Adobe Media Encoder for CS4 error Could not read from the source

Hello,
I get an error when I try to export from Premiere CS4. It doesn't matter how I export. Seems like an easy fix, but I can't figure it out. Any help is appreciated:
- Source File: C:\DOCUME~1\ARTWHI~1\LOCALS~1\Temp\extra and b roll.prproj
- Output File: E:\Living Accused Movie Transfers\video\Cindy at table.avi
- Preset Used: NTSC DV
- Video:
- Audio:
- Bitrate:
- Encoding Time: 16:10:34
1/21/2009 9:50:25 PM : Encoding Failed
Could not read from the source. Please check if it has moved or been
deleted.
Thank you
Art

When you attempt to encode media with Adobe Media Encoder CS4 on Windows, the following error message appears in the text file (AMEEncodingErrorLog.txt) that opens when you click the error icon: "Encoding Failed. Could not read from the source. Please check if it has moved or been deleted."
If it's that correct, you removed an earlier version of Adobe Premiere Pro or Adobe Creative Suite on the same computer.
Do one or both of the following solutions:
Solution 1: Create a shortcut to the Premiere Pro executable file, rename the shortcut to Premiere, and move the shortcut to C:\Program Files\Common Files\Adobe\dynamiclink.
Close all Adobe applications.
In Windows Explorer, navigate to C:\Program Files\Adobe\Adobe Premiere Pro CS4. (If you installed Premiere Pro CS4 in a location other than the default of C:\Program Files\Adobe, then navigate to your custom installation location.)
Right-click on Adobe Premiere Pro.exe (which might appear without the .exe extension) and choose Create Shortcut.
Rename the newly created shortcut to just Premiere.
Important: The name of the shortcut must be exactly Premiere with no other characters.
Open a second Windows Explorer window, and navigate to C:\Program Files\Common Files\Adobe\dynamiclink.
Move the Premiere shortcut that you created into the dynamiclink folder.
Solution 2: Remove and reinstall all Premiere Pro CS4 components or all Adobe Creative Suite 4 components.
Do one of the following:
Windows XP: Choose Start > Control Panel > Add or Remove Programs.
Windows Vista: Choose Start > Control Panel > Programs and Features.
In the list of installed programs, select Adobe Premiere Pro CS4, Adobe Creative Suite 4 Production Premium, or Adobe Creative Suite 4 Master Collection.
Click Change/Remove (Windows XP) or Uninstall (Windows Vista).
Follow the on-screen instructions to remove all components of Premiere Pro CS4 (including Adobe Encore CS4 and Adobe OnLocation CS4) or to remove all components of your edition of Adobe Creative Suite 4.
Re-install your Adobe software.

When I was talking on phone, suddenly the phone was switched off. i tried to switch it on but it gave the message....connect to itunes for set up. when I connected it to itunes...it gave the message, itunes can not read data from this iphone, restore it

when I was talking on phone, suddenly the phone was switched off.
i tried to switch it on but it gave the message....connect to itunes for set up.
when I connected it to itunes...it gave the message, itunes can not read data from this iphone, restore it to factory settings. It also said while restoring ypu will lose all media data but you can restore the contacts.
I restored the factory settings....the phone was on recovery mode...it was verified by itunes and all that..but in the end it again said that iphone has some problem and can not function right now.
after that when ever i connect it with itunes, it gives the message, it can not activate the iphone further, try again later or contact customer service.
What to do now?????? Customer service people say..it is hardware problem

If it's a hardware problem, then the phone will need to be replaced.
There is no magic that can fix a hardware problem.

VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction id in results:

Subject: VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction
id in results:
Hello All,
I am facing the following error while running a loadtest (when i choose the scenario to be executed for No of test iterations). But the same loadtest with the Run duration for X minutes is running fine without any issues.
Any suggestions on the issue i am facing
error is :
could not read result repository: unknown transaction id in results:
or
could not read result repository: unknown request id in results:
Thanks
Satish

Hi Kotapati,
>>Subject: VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction
id in results:
According to your description, you mean that when you run your load test using the Test Iterations way and then get the error message, am I right?
If yes, please you try to close the VS, and then open this VS again. Then clean your load test project/solution and then re-build it, run your load test again check this issue again.
In addition, I suggest you could try to create a new load test and then run it using Test Iterations way check if you get the issue for the specified load test or all load tests.
If possible, I suggest you could share me simple load test for us so that we will further help you.
You could upload your load test to OneDrive and then copy link here.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Firewire not reading

Similar Messages

Maybe you are looking for