Firmware 1.1 - What is the verdict - does it fix the buzzing noise?

I've been waiting to hear if Apple has resolved the issue of the buzzing noise with the 2nd Gen Nano. Those of you who have experienced this issue - has the new firmware resolved the problem for you?
I'm not sure whether now is the time to buy or not? I'm interested in the 8GB or 4GB models if that makes a difference however, from what I've read the issue has surfaced among all capacities.

I have said this a couple of times and I say it again...apparently I must be very luck because I did not experience this buzz on the 4gb I had briefly, the 8gb I currently have or the 2 that I purchased for birthday gifts to others. Because so many people seem to have been having this problem I wanted to make sure I didn't buy anyone buzzing gifts so I checked them both out. And apparently, no one that has the issue (solved at this point or not) have been able to get a real answer as to just what the problem is. I think this is also one reason why I don't really like to order my ipods...if there is an issue you can't just take it back to the point of purchase and get a replacement that same day (unless the Apple stores allow that...the closest one to me is about 100 miles away so I wouldn't know!).
Hope something happens soon for you!

Similar Messages

HT3964 resetting the SMC does not fix the fan

I replaced the HDD with an OWC SSD on my mid 2010 mac mini. Everything went together fine and installed mavericks with no issue. My fan runs at full speed and it wasn't able to adjust the resolution when I connected to my DELL 3008 monitor through HDMI. I resolved the video issue by connecting with a miniDP to DP connector but my fan continues to run at full speed. resetting the SMC did nothing.
I did snap the CD drive temp sensor connector on the logic board but I don't use the CD drive so I'm not too concerned about that. Would that have anything to do with this? would really like to get this machine going and not have it annoy me while I'm using it

It would seem the damaged/disconnected sensor is causing the problem. The singnal the logic board is getting or not getting would cause fan to run full speed.
You should be able to manually control the fan speed with an app like:
http://www.macupdate.com/app/mac/23049/smcfancontrol

HT1925 My computer no longer recognises my iphone and can't be seen on itunes. My ipod works perfectly on the same computer. rebooting my iphone and PC does not fix the problem.

When I connect my iPhone to my PC it is not recognised and iTunes does not open. When I connect my iPod to the same PC everything works perfectly. I conclude that the problem is not on the PC or with iTunes. Switching off and rebooting the iPhone and the PC does not fix the problem. Any suggestions??

Refer to this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538

What is apple doing to fix the bugs from IOS 7.1.2 update? this update has ruined my phone

What is Apple doing to fix the bugs from IOS 7.1.2 update??? This update has ruined my phone! Why would you put out a update you know is going to ruin someones phone? Whats being done? I have tried everything to fix my phone which was just fine before Apples IOS 7.1.2 update!!!

I have also experienced issues with my iphone5 since updating to ios 7.1.2, prior to this update my phone was working perfectly fine and I know I didnt cause any damage to the phone because I baby my iphone as if it was my child. Ever since I updated to 7.1.2 my phone shutts itself down while I am using it, it can be while using whatsapp, browsing the internet or using apps, more than anything it fails while using the internet. The screen will either start to flicker or vertical lines will pop up and then the phone will fade to black, after this happens the phone will get really hot and to turn it back on I have to wait 5-10 minutes and hold down the power and home keys at the same time for about 15 seconds for it to turn back on, I have to wait 5-10 minutes because if I dont when I boot it back up it immediately shutts down again. This is a constant all day thing and for now i get by just making phone calls and sending regular text but I try to keep the action down to a minimum to prevent missing a phone call. I tried clearing the phone and rebooting it to original setting but this didnt fix it. After reading and speaking with several techs they tell me that ios 7.1.2 rolled out some performance adjustments one particular that affects the amp levels that the battery works at and supposedly the iphone 5 cant handle it, they explained that the phone for certain activities is asking for more or less power and the phone panics into safe mode and shutts itself down. My battery life is fine so I havent changed the battery like someone had suggested. In the diagnostic data it gives a panic.ips error. Id really like to know if there is any possible way to roll back to 7.1.1 through jailbreak or any other way, I was perfectly happy with this phone and didnt plan on buying another one for atleast 1-2 more years. If anyone can help me out this would be greatly appreciated, if not I hope apple is working to fix this.

I have an iphone 5s and my phone was working perfectly fine then it turn into a blue screen and after that i tried to restore it but when i do the phone does half of the steps and then it turns into a blue screen and it doesnt work again what can i do?

i have an iphone 5s and my phone was working perfectly fine then it turn into a blue screen and after that i tried to restore it but when i do the phone does half of the steps and then it turns into a blue screen and it doesnt work again what can i do?

The Basic Troubleshooting Steps are:
Restart... Reset... Restore from Backup... Restore as New...
Malvinfromny wrote:
... i tried to restore it but when i do the phone does half of the steps and then it turns into a blue screen and it doesnt work again what can i do?
If you try all these Steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step... Be sure to make an appointment first...

I imported a video and when I play it back, the audio does not match the video. When I view the tape in my camera it looks fine. I've tried imported twice and each time it doesn't match. What can I do to fix this?

I imported a video and when I play it back, the audio does not match the video. When I view the tape in my camera it looks fine. I've tried imported twice and each time it doesn't match. What can I do to fix this?

The default settings mostly likely use an audio sample rate of 32k. This doesn't work probably in FCP. You're probably better off capturing the tape in iMovie.

When I buy a custom made calendar using iPhoto, what dpi or resolution does Apple print the pictures at?

When I buy a custom made calendar using iPhoto, what dpi or resolution does Apple print the pictures at?

The dpi you supply up to a max of 300 DPI as I understand it
LN

TS4291 I can't send mail from my iPad apps, I just get the error message, 'The recipient- was rejected by the server because it does not allow relaying.' Does anyone know what this means and how to fix the problem.

I can't send mail from my iPad apps, I just get the error message, 'The recipient… was rejected by the server because it does not allow relaying.' Does anyone know what this means and how to fix the problem.

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Using a POP account with multiple devices
http://support.apple.com/kb/ht3228
iOS: Adding an email account
http://support.apple.com/kb/HT4810
iOS: Setting up an Outlook.com, Hotmail, Live, or MSN email account
http://support.apple.com/kb/ht1694
Server does not allow relaying email error, fix
http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
How to Sync Contacts with Your iPad Using iTunes
http://www.dummies.com/how-to/content/how-to-sync-contacts-with-your-ipad-using- itunes.html
iOS: 'Mailbox Locked', account is in use on another device, or prompt to re-enter POP3 password
http://support.apple.com/kb/ts2621
eMail Groups - You can use a third party app that many users recommend.
MailShot - https://itunes.apple.com/us/app/mailshot-pro-group-email-done/id445996226?mt=8
Group Email - https://itunes.apple.com/us/app/group-email!-mail-client-attachments/id380690305 ?mt=8
iPad Mail
http://www.apple.com/support/ipad/mail/
Configuration problems with IMAP e-mail on iOS with a non-standard SSL port.
http://colinrobbins.me/2013/02/09/configuration-problems-with-imap-e-mail-on-ios -with-a-non-standard-ssl-port/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
 Cheers, Tom

I try to install my creative suite master collection (student version) on my new mac. the point is that when I want to write the product key. The computer does not accept the number 3. so what can I do ?

I try to install my creative suite master collection (student version) on my new mac. the point is that when I want to write the product key. The computer does not accept the number 3. so what can I do ?

Can you use the number 3 key elsewhere?
[topic moved to Downloading, Installing, Setting Up forum]

HT3529 I'm having trouble with my iPhone 5 iMessage service. The device does not recognize the users who have iMessage when I try to contact them using this feature. Who have the same issue and what did you do in order to solve it?

I'm having trouble with my iPhone 5 iMessage service. The device does not recognize the users who have iMessage when I try to contact them using this feature. Who have the same issue and what did you do in order to solve it?

Read here:
http://support.apple.com/kb/ts2755

The installed file can not be activated. Since the system does not perform the registration. What can I do?

The installed file can not be activated.
Since the system does not perform the registration.
What can I do?

I have the same issue. When trying to open the acrobat XI Pro for the first time, you are obligated to sign in with your account. But signing in is taking about an hakf hour now, while I have no problems signin in trough adobe.com with the same username and password.

HT204150 I have synced an iPhone 4S with iCloud - I now have a 5C to replace it. What happens to my data when I retire the 4S - does it need the original device to save my data?

I have synced an iPhone 4S with iCloud - I now have a 5C to replace it. What happens to my data when I retire the 4S - does it need the original device to save my data?

Welcome to the Apple community.
Once you have restored your new phone from the backup of your old phone and ensured that everything is working correctly, you should first turn off "find my phone" on the old phone and then erase it, before you get rid of it.

Any idea what this errorr means? the data type of the reference does not match the data type of the variable

I am using Veristand 2014, Scan Engine and EtherCat Custom Device. I have not had this error before, but I was trying to deploy my System Definition File (run) to the Target (cRio 9024 with 6 modules) and it failed. It wouldn't even try to communicate with the target. I get the 'connection refused' error.
I created a new Veristand project
I added the Scan Engine and EtherCat custom device.
I changed the IP address and auto-detected my modules
i noticed tat Veristand didn't find one of my modules that was there earlier. (this week)
So, i went to NiMax to make sure software was installed and even reinstalled Scan Engine and Veristand just to make sure.
Now, it finds the module, but when i go to deploy it getsto the last step of deploying the code to the target, and then it fails.
Any thoughts?
Start Date: 4/10/2015 11:48 AM
• Loading System Definition file: C:\Users\Public\Documents\National Instruments\NI VeriStand 2014\Projects\testChassis\testChassis.nivssdf
• Initializing TCP subsystem...
• Starting TCP Loops...
• Connection established with target Controller.
• Preparing to synchronize with targets...
• Querying the active System Definition file from the targets...
• Stopping TCP loops.
Waiting for TCP loops to shut down...
• TCP loops shut down successfully.
• Unloading System Definition file...
• Connection with target Controller has been lost.
• Start Date: 4/10/2015 11:48 AM
• Loading System Definition file: C:\Users\Public\Documents\National Instruments\NI VeriStand 2014\Projects\testChassis\testChassis.nivssdf
• Preparing to deploy the System Definition to the targets...
• Compiling the System Definition file...
• Initializing TCP subsystem...
• Starting TCP Loops...
• Connection established with target Controller.
• Sending reset command to all targets...
• Preparing to deploy files to the targets...
• Starting download for target Controller...
• Opening FTP session to IP 10.12.0.48...
• Processing Action on Deploy VIs...
• Setting target scan rate to 10000 (uSec)... Done.
• Gathering target dependency files...
• Downloading testChassis.nivssdf [92 kB] (file 1 of 4)
• Downloading testChassis_Controller.nivsdat [204 kB] (file 2 of 4)
• Downloading CalibrationData.nivscal [0 kB] (file 3 of 4)
• Downloading testChassis_Controller.nivsparam [0 kB] (file 4 of 4)
• Closing FTP session...
• Files successfully deployed to the targets.
• Starting deployment group 1...
The VeriStand Gateway encountered an error while deploying the System Definition file.
Details:
Error -66212 occurred at Project Window.lvlibroject Window.vi >> Project Window.lvlib:Command Loop.vi >> NI_VS Workspace ExecutionAPI.lvlib:NI VeriStand - Connect to System.vi
Possible reason(s):
LabVIEW: The data type of the reference does not match the data type of the variable.
=========================
NI VeriStand: NI VeriStand Engine.lvlib:VeriStand Engine Wrapper (RT).vi >> NI VeriStand Engine.lvlib:VeriStand Engine.vi >> NI VeriStand Engine.lvlib:VeriStand Engine State Machine.vi >> NI VeriStand Engine.lvlib:Initialize Inline Custom Devices.vi >> Custom Devices Storage.lvlib:Initialize Device (HW Interface).vi
• Sending reset command to all targets...
• Stopping TCP loops.
Waiting for TCP loops to shut down...
• TCP loops shut down successfully.
• Unloading System Definition file...
• Connection with target Controller has been lost.

Can you deploy if you only have the two 9401 modules in the chassis (no other modules) and in the sysdef? I meant to ask if you could attach your system definition file to the forum post so we can see it as well (sorry for the confusion).
Are you using any of the specialty configurations for the 9401 modules? (ex: counter, PWM, quadrature, etc)
You will probably want to post this on the support page for the Scan Engine/EtherCAT Custom Device: https://decibel.ni.com/content/thread/8671
Custom devices aren't officially supported by NI, so technical questions and issues are handled on the above page.
Kevin W.
Applications Engineer
National Instruments

HT201272 What if the video does not have the download icon?

I have an ipod classic and i am trying to download an HD movie to it. But it doesnt have the download icon i need that it shows in the steps. please help.

Nothing. If the carrier does not unlock the phone you cannot. Only the carrier can unlock it and Apple does not and never has unlocked the iPhone.

New 13" Macbook Pro trying to connect to a Panasonic VIERA TC-L42U30 as second monitor. I've used multiple hdmi-thunderbolt/mini displayport adapters and multiple hdmi cables and still no success. The Macbook does not sense the second monitor (TV). Help?!

I've been a Mac since 2008, so I know my way around the system pretty well. This issue, however, has me stumped. I had an iMac until now and only now am I experiencing some difficulty with my new MacBook Pro. The model I have is the newest 13" Macbook Pro model and I'm trying to connect a Panasonic VIERA TC-L42U30 42" HDTV as a second monitor via the Thunderbolt port.
It worked the first two times and hasn't worked since, after 10-15 attempts with different configurations, turning things on n off, restarting the mac, unplugging the cables, adapters, TV, resetting the P RAM, etc... I've used multiple hdmi-thunderbolt/mini displayport adapters and multiple hdmi cables and still no success. No matter what I do, the Macbook does not sense the TV as a second monitor anymore.
I took the MacBook Pro to the Apple Store, and their "genius" there had it working fine with a DVI connection to a regular monitor. The Panasonic TV I have has HDMI connections and one VGA connection which does not support HD, but no DVI option. I want an HD connection to mirror or extend my MacBook Pro screen. At the Apple Store, they didn't have a Thunderbolt/Mini DisplayPort to HDMI adapter, so he could not try that out for me.
Anyone else have this configuration or another similar one with a Panasonic HDTV?
Ideas? Suggestions? Anything?! Help!!
P.S. I'm running Mountain Lion, if that wasn't already obvious. Everything is up to date in my App Store as well.
Thanks!

Hi There,
I have had the exact same issue but with a projector.
The issue lies with Mountian Lion 10.8.2.
I tried many a combination with no luck to get HDMI working.
Took my mac into the apple store and came to the conclusion it was the software, so I asked them to install 10.8 onto it (this is destructive so a backup is a must)
Bought my macbook home and voila, now displaying through my projector.
There is a small graphics update after 10.8.1 which seems to be the cause.
Hope this helps.
Thanks.

Firmware 1.1 - What is the verdict - does it fix the buzzing noise?

Similar Messages

Maybe you are looking for