Firmware for DVR-K12TBS

Hello,
is there ja new Firmware for the DVR-K12TBS DVD Writer from Toshiba? (Model No. PA3358E-1DV5)
My current Firmware is 1.15 (09/2004)
This is very old and there are many DVD+-R that i can only burn with low speed.
Thanks.
Thomas J.

Hi
Well, it would be very interesting to know which unit do you have.
Nevertheless you can check this Toshiba download page:
http://www.toshiba-europe.com/storage/Index_home.asp?nav=HOM&page=HOM&frame=home&model=x
or this one:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
Bye

Similar Messages

  • Current Firmware for DVR-110D?

    I just got a DVR 110-D and installed on my G4 running 10.3.9. Seems to be working fine using Patchburn and Toast 7.01. Another post suggested to get the latest revision of firmware installed for the drive. I tried the Pioneer site and they only support updates in windows formats. My drive is listed as rev. 1.11/MMC. Is this the latest rev? If not, do I have to yank the drive and put it into a windows machine to flash it? I am on a network with a windows machine. I could download the patch on there and hope to see the drive across the network for the update if it's even required.
    Thanks,
    Bruce

    I found that the current version of firmware for the 110D is 1.39. I ended up flashing the unit in a windows machine and reinstalling into the mac. Ran Patchburn and the drive runs perfectly on all apple software as well as Toast.
    Done deal!
    Thanks for the help.
    Bruce

  • Firmware for DVR-109?

    Where do you find the firmware update for a Pioneer DVR-109. I found it on the pioneer website but it was a download for windows. I have a PowerMac G5 Dual 2.3 (early 2005 model) and It wont recognize Memorex 16x media in Toast 7. It will only allow me to burn @ 12x. The Apple rep at Comp USA said that all media is compatible with PowerMacs these days. I need help. Thanks.

    no experience but here's a thread
    http://discussions.apple.com/thread.jspa?threadID=119519&start=0&tstart=0

  • Any way to upgrade firmware for Pioneer DVR-K06 DVD-RW drive?

    Finally got around to replacing the factory SuperDrive in my Mac mini the other day. The original drive NEVER worked right out of the box -- would read some CDs but not others, always barfed on burning DL DVDs, etc. My last experience with getting a mini fixed under warranty (mobo on my 1.42 G4 took a dump after a few months) involved two three-hour round trips to the nearest (and I use the term loosely) Apple Store for service. It was cheaper for me to just replace the optical drive in this one than to do that drive again.
    Anyway, enough complaining. The replacement drive has firmware v1.01 and I would like to get it up to the latest available firmware to take advantage of any compatibility, stability, etc. fixes since v1.01. Problem is that I can't find any software that supports flashing the K06 drive. Hope someone here has a solution. I don't have a Windows machine with appropriate connectors to hook the drive up to or I'd go that route ... plus I'd much rather do it on a Mac just on principle ... plus I don't want to have to disassemble the mini again.
    Any solution?

    Hello Sang,
    I have Sun Ultra 40 Workstation which comes with Matshita DVD-RAM drive.
    Mine has D100 firmware and I find other people who has the same drive on different system have D101, D200, D201 firmware.
    So does anyone know how to contact Sun to get the latest firmware for my DVD-RAM drive?
    I did contacted Matshita for this matter and they tell me to contact Sun.
    I did review the Full Components List for the Ultra 40. The only DVD drives listed (Part No. 370-7970) are Panasonic UJ-485 and Teac DV-W28SLA-093. Both aren't capable of reading or writing DVD-RAM.
    In some countries Panasonic uses Matshita as brand name.
    I did a search on SunSolve with the keywords DVD firmware.
    Sun supplies only firmware updates for two DVD readers: Toshiba DVD 1401 (fixes: unable to boot from Solaris 8 DVD) and Toshiba SD-C2732 (fixes: returns incorrect data).
    I was unable to update the firmware of the SD-C2732 (Sun part) with the Sun patch. The drive was attached to an Ultra 10 (with an adapter). I ended attaching the drive to a PC and using a DOS boot floppy with the Toshiba flash program and the Sun firmware.
    Regarding you problems with the drive: Have you tried another brand of media. The Ultra 40 is under warranty (GA date was February 14, 2006).
    Use the contact information from your other thread.
    If you search the net for firmware you can locate sites that offers region-code-free firmware for several drives. Usually they provide a flash program (requires creation of a DOS boot floppy). Using these programs/firmware voids your warranty. Maybe you can not revert the firmware upgrade.
    These slimline drives have no jumpers, the installed firmware (of the drive) determines if the drive is master, slave, uses cable-select (CS) or reversed CS.
    Michael

  • Latest DVD Burner Firmware for Power Mac G5?

    I'm trying to find the latest firmware for the DVD burner that shipped with my Power Mac G5, where I can find it and how to install it.
    My machine ID:
    Model Name:          Power Mac G5
      Model Identifier:          PowerMac11,2
      Processor Name:          PowerPC G5 (1.1)
      Processor Speed:          2.3 GHz
      Number Of CPUs:          2
    The Burner ID:
    PIONEER DVD-RW  DVR-110D:
    Firmware Revision:          AA06
      Interconnect:          ATAPI
      Burn Support:          Yes (Apple Shipping Drive)

    Hi Thomas, check out...
    http://lasvegas.rpc1.org/

  • Unable To Repair/Update Firmware for a Creative Nomad Jukebox

    Hello all,
    I've been trying for the past...3 or 4 hours to get my player to work, but it simply refuses to work =P. I sent the problem into Creative, but haven't gotten a response for a couple days now. So, here's a copy-paste of what I sent in that e-mail. If you can think of anything that might help, please don't hesitate to post! I really need your help on this one!
    My player's hard dri've recently died, and I received
    a replacement from the original store (a CompUSA).
    However, my Firmware for the device has failed. I
    tried the firmware upgrade for my Zen, but after
    a certain number of tries, I gave up. Here is the
    list of steps that I followed.
    On Zen: Click "Reload OS", let it run, it says
    run the firmware upgrader now.
    On Computer: "You cannot install this firmware
    update with your player's current drivers using
    the SB394 connector. To update your player's
    firmware, this application will temporarily
    replace the current drivers and restore them after
    the installation is complete. Continue
    installation?", I click Yes. Then it says to
    disconnect, and re-connect. I do it.
    It shows my version (.2.0), and I'm upgrading/
    repairing it to .2.02. When I click "Upgrade", a
    warning message pops up and says:
    "Your player cannot start up properly. Please
    reboot your player and run this application again.
    I've done this at least 0 times, and nothing changes. My player is a Nomad Jukebox Zen, the one with a FireWire connection, and like I said,
    I've tried this at least 0 times with the same results. Is there a process to completely remove
    the firmware on the device, then reinstall it,
    or to roll it back or something? Any other ideas
    to fix this problem is needed as well.

    Bump.

  • Can't find firmware for BEFW11S4 v2

    I'm having trouble finding a firware update for v2 of my BEFW11S4 router. The support page for this model offers a firmware update for v4 only. My current firmware v. is 1.45, which may be the latest version, but I can't seem to find this out anywhere on the Linksys website.
    The reason for the update is that my neew iPod 2G won't connect to the internet and I'm guessing an update might help.
    Thanks in advance for any assistance.

    You can Download 740 KB firmware for BEFW11S4 V2 and save it on the dekstop
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
    Click on the 'Help' tab- Then click on the 'Firmware Upgrade' .... Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    If your Internet Service Providor is Cable follow this link
    If your Internet Service Providor is DSL follow this link

  • After downloading firmware for airport utility, airport express base station no longer registers with airport utility on my Mac. Now the base station is blinking amber with no info of what is causing all this to happen. Any suggestions?

    After downloading firmware for airport utility last night, airport express base station was deleted from airport utility and only Time Capsule remains. When I plug in the base station, an amber light blinks without being able to verify the cause. Any suggestions to remedy this problem?

    There are only a couple of things you can do to resuscitate a nonresponsive Express:
    "Hard reset":
    Press and hold the reset button with a pen or pencil until you see the status light (LED) start to flash amber rapidly, which should occur after about five seconds.
    If that does not work,
    "Factory defaults reset":
    Unplug the Express from power.
    Press and hold the reset button with a pen or pencil, then plug the Express back in while continuing to hold the button until you see the light (LED) flash rapidly. This should happen after a few seconds.
    Release the button.
    In either case you will have to reconfigure the Express as a new device. A moment or two after it has been reset, the LED should be blinking slowly. It must then appear in your Wi-Fi menu like this:
    Earlier versions of OS X will report it as "Apple Network nnnnnn".
    In either case, select it, and then launch AirPort Utility.
    If it does no appear in your Wi-Fi menu after it has been reset using one of the two techniques above, it is defective. Other than attempting another reset, there is nothing you can do.

  • For when a new firmware for normal N73?

    I know there is a new firmware for N73ME, my question is, anybody knows when will be release a new firmware for normal N73, with same improvements like N73ME (or more).
    Message Edited by naf1970 on 16-Jan-2008 07:22 PM
    Nokia N8 / N9 / Lumia 920 White

    29-Feb-2008 06:26 PM
    1983 wrote:
    I think N73 wont get any more updates... The new line of candy bar nseries is the target now: N82 and N78, and the other N81, N95s and N96,
    N73 is almost as old as N80, and n80 isnt getting any new updates. Sorry.
    ur wrong
    Nokia 5800 XpressMusic (11) [Product ID: 0559416]
    V 21.0.025 (date: 02-04-2009)
    network: mobily (etihad etisalat)

  • We are desperately waiting for a new firmware for ...

    hello nokia,
    we are using one of your most popular mobile the n73- music edition ( product code for my mobile 0564012)
    as it is seen over the internet that nokia is rolling out firmware updates for their s60v3 devices like some of the e-series.., i just want to know if nokia will release a firmware for our mobile..??
    if not.., its our humble request to release one.., which can provide better performance and stability..
    most common complaint is regarding its speed..
    for eg while entering to menu the mobile becomes sluggish.. even if the phone memory is empty n no memory card is ther...
    i've nokia n8, 5230, e63 at present in my family n i'm a big fan of nokia n iu'll be glad to see your  reply soon..., n ofcourse the new firmware.... pplllllssssss   do the needful..,
    ignore mistakes if any..

    The N73 was long since discontinued. There will be no further firmware updates for that model.
    If you are unhappy about that you can complain to nokia using the "contact us" link near the top or bottom of this page.

  • New Firmware For Nokia C3-00 : Reviews and Problem...

    Today i installed the newest firmware for nokia c3-00 : 8.65 with great anticipation that it would fix the problems and thats what i found out after hard and soft resets many times...
    ** Chat application is still not accesable. I just cant open it in the MESSAGING section even if i click it again and again ... can you fix this?
    ** As for communities, i am getting error of SERIVCE TEMPORARILY NOT AVAILABLE. I hope it really is a temporary error, and we dont have to wait for another firmware update.
    ** A CHAT APPS icon has poped up in my mobile phone and when i click on it , it takes me to nokia ovi's page of some mobile messengers and in which i can only download ebuddy and as for the rest i am getting error that 'THIS ITEM YOU ARE TRYING TO DOWNLOAD IS NOT COMPATIBLE WITH YOUR DEVICE AND/OR COUNTRY. DETECTED DEVICE NOKIA C3-00/PAKISTAN. 
      Does that means we wont be able to get our old ovi chat application ever? i liked that one because i had the facility to minimize the chat application and get notifications of messages. Cant you fix this because i cant do that with the 3rd party chat apps.
    Waiting for reply ...

    Hello friends!! 
    I had the same problem with this firmware update
    and for a moment I thought I had ruined my phone, but it occurred to me
    perform a factory reset on the phone and Communities and Chat surprise and something that works perfectly also note is that the browser to retrieve the factorygoes a little faster.
    I mention it again from your phone please contact Menu> Settings> Restore FactorySettings> All, expect to complete the restoration and your phone is 100% functional.
    Note: Before you restore a backup made ​​of all your files, emails, contacts, etc. That everything is removed with the restoration.

  • New firmware for Nokia N73 ME v4.0736.3.2.1

    Finally new firmware for N73 ME (RM-133)- product code 0539291.
    I'm updating my phone right now, but as all previous firmware versions, there is no change log. We have to figure out what has been fixed this time.
    Keep it cool )Message Edited by dejanos on 09-Oct-200704:26 PM
    Message Edited by dejanos on 09-Oct-200704:27 PM
    Nokia N73 ME RM-133 v4.0736.3.2.1
    Memory: 2GB Apacer miniSD

    09-Oct-200704:26 PM
    dejanos wrote:
    Finally new firmware for N73 ME (RM-133)- product code 0539291.
    I'm updating my phone right now, but as all previous firmware versions, there is no change log. We have to figure out what has been fixed this time.
    Keep it cool )Message Edited by dejanos on 09-Oct-200704:26 PM
    Message Edited by dejanos on 09-Oct-200704:27 PM
    is this the changelog?
    ttp://europe.nokia.com/A4577225 has the details of the new firmware
    Nokia N73 Software version 4.0735.3.0.2 / 4.0736.3.2.1 released - 9 October 2007
    This software version includes Nokia Maps 1.0 (edition 1.2) for use with Bluetooth GPS devices. This release also includes updates to the Music Library and music downloads, and performance improvements to SMS and device application installers.
    Blackberry Bold

  • New Firmware for Nokia C5

    When will nokia launch new firmware for nokia C5?....its been a lot of time from last firmware about 6 months...Please Nokia launch new firmware for Nokia C5
    Thanks

    Are you asking or requesting...........
    Nokia themself does not know the answer for it, As you know the product is geting older
    Hope they come up with one more update

  • New firmware for Nokia C7-00

    After a quick search around, i get completely lost about the right and safe firmware for this phone.
    There are some issues ready to be fixed, so im guessing nokia is working on that. Having that said, i see to many firmwares, to many versions, to many sources, absolutely no oficial news on that.
    Using the phone itself, there are no new updates.....
    Mine:
    Edition: PR1.0
    Soft Version: 012.003
    Version Date: 2010-09-19
    Personalised Version: 012.003.262.02
    Personalised Version Date: 2010-10-08
    Language Set: 012.003.11.01
    Product ID: 059D9Q6
    Model: C7-00
    Type: RM-675
    Last Update: No updates
    Browser Version: 7.2
    Flash Version: 4.0
    Java Version: 2.1
    3 questions:
    a) Is this the latest firmware?
    b) There are some unoficial notices about a 012.004 version. How can i know if its reliable?
    c) Where can i look for new firmware without using my phone to search it?
    Many thanks!

    Thanks steceso,
    Allready seen that page. Like i said, no oficial notices for new firmware for C7...
    Actualy, even i dont input my product code, when i select the phone, immediately i get: There are no software updates available for this product yet
    So, i understand  there is zero releases for this phone, since its exists....
    Hope im wrong.
    Paid big money for a phone who doesnt identify the sms sender.....
    Really frustrating....

  • New firmware for nokia N85

    Hello. I would like if you were lazy people from Nokia have made a new firmware for Nokia N85.
    It is a shame that for some older models released new firmware. But even so it is only a few cell models of Nokia's touch-type screen.
    Shame on Nokia. Wake up in the centrale and start finally doing something for people.

    send your inquiry to Nokia by clickin this link
    http://europe.nokia.com/support/contact-us
    Glad to help

Maybe you are looking for

  • Using sound for Enemy Territory and TeamSpeak

    When I'm playing a match of Enemy Territory I would like to still here the sound that TeamSpeak produces. I've tried numerous things, but I can't get ET and TS to work together. Does anyone have a succes story they can share with me? my current .asou

  • Problem with GL accounts

    Hi Gurus when i was editing and saving Parked Documen it was giving two errors, one is GL 300568 has been set as not relevent for tax for one documents and for another doucemtns account 6698597has been set as not relevent for tax any idea regards Sun

  • TS1389 the above steps are still not solving the problem

    Following the steps recommended in http://support.apple.com/kb/TS1389 does not solves the problem. Did someone had the same problem and was able to solve this ?

  • Blending Modes 101 | Learn Photoshop CS6 | Adobe TV

    Blending modes are one of the most creative areas in Photoshop. Let Infinite Skills author, Andy Anderson, take you on a tour of this amazing area in Adobe Photoshop. http://adobe.ly/NsBIKV

  • How do I add auto text based on value in numeric field?

    Need help... I'm trying to add auto text to a text field based on a value in a numeric field. I want my text field (summary box) to say "Passed" if the value (score box) is equal to 10 and the field to say "Not Passed" if the value is equal to less t