Firmware question for Color LaserJet: Two computers on my network, Win XP and Win 7. Does it matter?

I don't understand firmware, but I know I needed to update my CP2025dn printer's firmware.  I used my older computer to do this.  If I had used my newer computer with Windows 7, would this affect my printing from either computer?  Thanks.

I have tried to install my HP color laserjet 2605 dn on my windows 7 operating system and I get an administrator error

Similar Messages

  • How to access files from two computers on a network, one wired and one wireless?

    I cannot seem to access one computer from the other.  I have marked files for sharing, and both show the same work group.  How do I make sure both computers are installed on the router?

    Make sure that both computers can access the Internet through the router.
    If your router has a setting for "AP isolation", verify that it is set to "disabled".
    As long as you do the two things mentioned above, your router does not put up any barrier to file sharing.   So then the problem is not a router problem, it is a Windows problem, or a firewall problem.
    To check for firewall problem, first, make sure you can ping each computer from the other - if you cannot, then temporarily turn off your software firewall, including Windows Firewall, and see if that helps.
    If you still have problems after the firewall is off, then your problem is likely a Windows problem.   Make sure "file and printer sharing" is enabled on all your wireless adapters and ethernet cards.   If you continue to have problems, then usually the Windows support website has the best info on how to further proceed with fixing this type of problem.
    Hope this helps.

  • Hello , can you with a single account creative cloud , install on two computers ? (The one from home and one at work)

    Hello , can you with a single account creative cloud , install on two computers ? (The one from home and one at work)
    This will avoid me lugging around my mac, sorry for my english.
    Margaux, photographer

    Yes, this has been allowed with Adobe applications going back many years.  A program such as Photoshop can legally be installed and activated on two computers at a time for the use of the single licensed user.  You can't install legally on your own and a friend's computer for use by the two different people.  Prior to Creative Cloud, there was an unwritten limit on how many times a given application could be activated, but there is no longer such a limit under CC.  That means you could theoretically install on three or four computers, activating only two at a time, and then deactivating one or both before activating on another computer.

  • HP Color LaserJet CP1518ni & Windows 7 via network

    I have a HP Color LaserJet CP1518ni connected to the network, not via a USB cable. How to I setup this printer so I can print to it from my WIndows 7 machine? Will HP be coming out with anything other than the Universal Print Drivers for this printer? If so, when?

    The full feature download for your printer supporting windows 7 will be available for your product in late January 2010.
    While I am an HP employee, I am not a expert on all our products. When I offer advice, I'm not speaking for HP.
    I am an HP employee.
    Regards,
    Vidya
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
    ***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

  • Can I sync two computers when one is using lion and the other snow leopard

    can I sync two computers when one is using lion and the other snow leopard

    will my data be shared well using Mobile Me?

  • I cannot see my itunes library on the main menu under computers despite the network being active and the home sharing on on both the devices the mac and apple tv. Any ideas?

    I cannot see my itunes library on the main menu under computers despite the network being active and the home sharing on on both the devices the mac and apple tv. Any ideas?

    Hi Monty,
    Sorry to say it, but this is normal for Apple TVs. I've owned a TV2 and a TV3, and neither lasted for an entire year. They are quite fragile and of low quality, and as you can see here, quite fussy even when they work. The wi-fi receiver on these are cheap and unreliable.
    Consider the $99 an annual rental fee. They rarely work for a whole year, so if you are going to use the platform, you will have to replace them constantly.
    Also, when one dies under warranty, never, never send it to Apple for repair. Go to the Apple Store for replacement. I sent my ATV3 in for warranty repair using a box sent to me by Apple, and although FedEx tracking showed it was accepted by Apple, it was never seen again. Apple won't replace it or even return my calls.

  • EPrint for COLOR LASERJET CM3530 MFP

    I have purchased 6 COLOR LASERJET CM3530 MFP for sales reps around the business i work for. It would be great if ePrint functionality was available for these printers
    Are they expected to recieve a firmware upgrade to enable this functionality and if so do you have a time frame for this.
    thanks

    Any update if there will be a firmware update for this model of printer to enable ePrint
    COLOR LASERJET CM3530 MFP

  • "waiting for Color Laserjet 2550L to become available" when trying to print

    I have been successfully printing to a Color Laserjet 2550L for over 4 years yet suddenly within the last 2 weeks each time I try to print I get this message from the printer window: "waiting for printer to become available"?  Oddly enough, if I power the printer off and then back on the printer usually (although not always) prints whatever has not been completed in the queue.  I have tried using different USB cables, deleted and then added this printer again ... not sure what else to try?
    I was messing around with my network in trying to get another Color LJ to work but don't see how that could affect this printer since this one is running direct via USB and seems to be getting the info just not printing without the power down?  Any help is greatly appreciated!  Thanks

    OK, that's strange.  Apple and HP list it as being supported by Snow Leopard here.
    Can you run a self-test from the front of the printer?
    Try downloading updated software from Apple here.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Wireless Printing for Color Laserjet 2505dn

    I keep getting emails from HP regarding wireless printing.  So, I'm trying to find out if mine is compatible to do it. I have a Color Laserjet 2505dn printer.  I think it is too old and is not compatible but I was hoping someone can tell me for sure if there is possibly a way to do it.  I have a wireless router to my computer but can it reach my printer?
    Thanks
    Walter

    Hello WalterK,
    I understand your concerns. Unfortunately, for this type of printer, I need to direct you to our Enterprise Business Community Forums. This will be the right section to troubleshoot this issue. Good luck.
    I worked on behalf of HP.

  • Exchange 2013 Site Resilience - Basic questions for setup in two seperate AD Sites, same domain

    I am just getting ramped up with Exchange 2013 and have a friend that I am assisting with planning an exchange 2013 deployment for.  I am not asking for step by step directions for setup, just asking for a basic overview so I can dig in to this and
    assist.
    Goal is to have an exchange server, one in NC and one in Switzerland in an active/passive mode for site resilience.  Both servers will be multi role servers. 
    This is a small organization, less than 50 users and on a budget for equipment.  HQ is in NC and the server will have all roles installed on a single server. Switzerland will have only one Exchange server for fail over.  There is only
    one domain total with two AD Sites. 
    My questions for clarity -
    1. Can I create a Site resilient deployment with two Exchange Multi Role servers in these locations?
    2. Currently, the organization does not have a Load Balancer.  Will this be required? 
    3. They do not have a third location for a Witness Server, what issues could potentially happen if the witness sits in one of the two sites?
    4. Any other basics for this design are much appreciated.  I am reading a lot, however a little confused as I read through the requirements.
    Thanks for your input and direction!
    Wall

    Hi
    Please find below answers to your questions.
    1. Can I create a Site resilient deployment with two Exchange Multi Role servers in these locations?
    Yes
    2. Currently, the organization does not have a Load Balancer.  Will this be required? 
    No you don't need to have a load balancer. As you are setting up the infrastructure in Active / Passive mode you don't need a dedicated LB for this.
    3. They do not have a third location for a Witness Server, what issues could potentially happen if the witness sits in one of the two sites?
    The issue with the witness server in primary or DR site is if your witness server is not responding your DAG won't work properly (failover). If you don't have a 3rd site then you can setup a witness server in your primary site and Alternate witness server
    to your DR site.
    4. Any other basics for this design are much appreciated.  I am reading a lot, however a little confused as I read through the requirements.
    I would recommend to use Exchange sizing calculator and technet is the best resource for you :)
    Kindly mark this as answer if it fulfill your requirements. :)
    Regards, Riaz Javed Butt Consultant Microsoft Professional Services MCITP, MCITP (Exchange), MCSE: Messaging, MCITP Office 365

  • Can you tell me if you have drivers for color laserjet 2605dn for windows 7, and a easy way to downl

    Drivers requires, color laserjet 2605DN for windows 7 64 bit

    You can find all available software for that printer here. 
    http://h20000.www2.hp.com/bizsupport/TechSupport/S​oftwareIndex.jsp?lang=en&cc=us&prodNameId=1140731&​...
    I hope you found this link helpful.
    If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
    Although I work for HP, my posts and replies are my own opinion and not those of HP.

  • Drivers for color laserjet 5m printer (windows XP)

    My computer crashed and burned - had to reinstall Windows XP - can't find right drivers on HP website for my Color laserjet 5  (c30991)   Any suggestions on were to go?

    The windows 8 driver for this printer should be available in late January. Please bookmark this site and visit it for up to date information. Also located on this site are links to documents for the network workaround and the in-os document.
    Laserjet Printers supported in Windows 8
    Install HP print software via a network in Windows 8
    As a test, I did install this using the windows 7 drivers, it printed fine but I received a pop up giving me an error printing but it still printed. I then used the network work around to shut the bi-di off and the pop up went away, again it printed fine. I would suggest if you use the windows 7 drivers, that you upgrade to the windows 8 drivers when they are available.
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as Accepted Solution

  • Question about syncing between two computers

    I feel a bit silly, because I feel as though I should know this, but I'm not sure because it has never applied to me until now.
    My main computer is a Vista machine, and everything is sync'd with that. However, I bought a MacBook last night (WOO-HOO!) to use as a secondary machine, and I'd like to get all of my contact and calendar info into that machine as well.
    I'm envisioning the following scenario:
    1. I will put at least one contact and at least one calendar event into Mac Mail and iCal in my new, empty MacBook...
    2. I will connect my iPhone to sync with the MacBook and iTunes will offer me the magic "merge" option.
    3. All of the information in my phone will be sync'd to my new MacBook, and I will have two computers and an iPhone all with the same info.
    Are there any holes in my vision? Will this work?
    Thanks,
    -SB

    This should work as provided.
    If something goes wrong with the sync process with your MacBook and this data is lost on your iPhone, you have your Vista machine with this data to recover from.
    If you aren't already doing so, be sure to create a backup of this data on your Vista machine - contact information and calendar events - which should be done when syncing any device such as an iPhone with such important information stored on your computer.

  • HP Color Laserjet CP1215 on XP home network will not print from second computer.

    Win XP SP3 home network with two computers and one HP Color Laserjet CP1215 printer(USB) that is shared.   Computer one prints just fine, but second computer cannot print.
    Print job goes to the queue and says "printing" and stays there for about two minutes and then says "error - printing" and then I have to delete the print job from the print queue.
    Downloaded latest CP1215 print driver and installed it to second computer, added printer just fine.  No errors until the print job enters the queue. Downloaded the CP1215 Diagnostic Utility, but it will not work on second computer.  Have not tried it on first computer when job errors.
    Message Edited by remleys_west on 06-23-2009 10:29 AM
    Message Edited by remleys_west on 06-23-2009 10:35 AM

    The Firewalls are disabled and from my laptop you can view all of the shared
    Folders on the Desktop with the CP1215 attached via USB.
    When I issue the print from my laptop that is on the same network, you see the
    print file show up in the CP1215 print queue of the Desktop the CP1215
    is USB attached to and then disappears about 15 seconds later.  Here is
    how it appears on in the Desktop CP1215 Print Queue before it disappears
    Doc Name            Status      Owner     Pages    Size            Submitted            Port
    E-mail print           Printing      Guest          1      547 KB     2:00pm 08/26/09      USB003
    I've also download/installed the latest drivers.  When I reinstall the CP1215 on my laptop from
    the Desktop, the "PRINT TEST PAGE works from the Laptop but then all print commands after
    that do not work.
    I see from my Google search I'm not the only one having this problem
    ANY IDEAS what to try next? 
    Wes

  • Color LaserJet 1600 on a home network?

    I'm looking for a way to make my Color LaserJet 1600 available to my entire home network.  It's currently connected via USB to my wife's desktop running Vista Home Basic, which in turn is connected via ethernet to my router.  The other three machines on the network are my two daughters' desktops running XP Home and my laptop running Vista Home Premium; all three are on the wireless side of the router.  Can anyone recommend a reasonably priced wireless or ethernet print server that is compatible with the Color LaserJet 1600?  Failing that, is there a workaround I can use to let all the computers on the network share the printer while it is connected to my wife's computer?

    You can use windows printer sharing to let everyone on your home network print to your LaserJet. Here is some instructions from Microsoft on using windows printer sharing with Vista:
    http://windows.microsoft.com/en-US/windows-vista/Enable-file-and-printer-sharing
    The primary disadvantage of this approach, compared to a dedicated print server, is that your wife's desktop must be on and running for others to print.
    -David
    (I'm an HP employee, but I am speaking just for myself and not HP.)

Maybe you are looking for

  • How to resolve compatibility of Acrobat 5.0 in Windows 7?

    How can one resolve the issue of Acrobat 5.0 being non compatable with Windows 7?   Is there a work around?

  • G3 B/W 400 MHz Refuses to Boot

    I've tried absolutely everything, but I always get the Mac face and a question mark. I did succeed once in booting a hard drive, but the Linux installation was corrupt. I've tried booting off of multiple CDs and that doesn't work either. I think my b

  • How do you manage different target platforms from one FLA?

    I am in the throes of trying to publish an app for both iOS and Android mobile devices and am having trouble finding some guides related to how to most easily target these two platforms without duplicating code or FLA files. So far, I have one single

  • Making a 300 image "movie"

    My project is to make a DVD containing 300+ still images (from a digital camera) with timed music with 4 chapters. I'm using iMovie 09 and iDVD 09. I know iDVD can do slide shows but I have too many stills. I authored the show in iMovie 09 but when I

  • Link problem in Internet Exlporer

    A few months ago I launched a new Dreamweaver site for a client and all links were working. I recently added some thumbnail images (to those already there) and on the pages with the new images the 'Hotspot' links to the following pages do not work in