Firmware upgrade correct steps?

We are carrying out a firmware upgrade on our 9509’s from 3.3(1c) to 5.2(2) and I want to know if the steps below are correct?
Check hosts for paths to both Fabric's.
Take a backup of the config for all the switches.
On Fabric A upgrade switch 1 to 4.1(x)
Upgrade switch 2 in Fabric A to 4.1(x)
On Fabric A upgrade switch 1 to 5.0(x)
Upgrade switch 2 in Fabric A to 5.0(x)
On Fabric A upgrade switch 1 to 5.2(2)
Upgrade switch 2 in Fabric A to 5.2(2)
When happy, then do the same for Fabric B for the other switches.
Thanks

looks good, just follow the release notes to go to the correct intermediate code level so that upgrade is non disruptive

Similar Messages

E71 Firmware Upgrade Step-by-Step (Undocumented Ti...

Although Nokia’s firmware upgrade claimed to be smooth using Nokia Suite, the fact it is not. There are many things which could interfere with the process. For example upgrading E71-1 firmware from 100.07.76 to 110.07.127 is not always trouble free. Based on experience, here are precautions to take:
Before you begin:
• Make sure your phone and computer/laptop are fully charged.
• Make your personal data is backed up safely.
• The BEST, FASTEST and EASIEST way of saving your personal data is making a copy of your phone memory on a memory card. Choose Tools > Memory > Options > Back up Phone Memory and wait until it will be competed.
• Make sure Nokia PC Suite is not running.
Upgrade Process Instructions:
1. Download and install latest “NokiaSoftwareUpdater” http://europe.nokia.com/A4579163 .Reboot if required.
2. Disable Antivirus or any other interrogative software on your PC.
3. Launch “NokiaSoftwareUpdater” and follow instructions
4. When prompted, connect your phone, in this case E71.
5. A 3-step process will start, identifying your phone, downloading latest firmware and upgrading to latest firmware. (a process of 15 min.)
Following those instructions will ensure a hassle-free upgrade.
Good luck.

I have a related issue on my E71-3 (New Zealand). Since moving to Firmware 501.21.001 contacts I have in 1-touch keep dropping off - not all, just the odd one here & there. In addition, the group ring tones for the same contacts are dropping off. Very odd. Most frequently it is my partners number impacted, which is why the issue stands out to me ... On start up, I'm now getting a message saying not all applications can be loaded from the memory card - on checking app manager, they are all loaded ... Anyone else having these issues?
iPhone 4 is looking more & more tempting by the day ;-p

Creative MuVo TX FM Firmware Upgrade 1.18.02 - The End For Many Players - Par

This is part 2 of the story since you cannot post such a long message in one posting.
>>Dear >>>>in my first mail I wrote already:>>>>After installing the recovery driver I run the >>firmware update again. It says that it found a >>device in recovery mode and more (pretty quick >>message) and after this it searches for this >>device - and does not find any device connected >>to an USB port.>>>> From this statement you can see that I installed the recovery drivers
>>and put the player in recovery mode. Then the player is seen by your >>update software since it finds the player in recovery mode. But after >>this it cannot transfer the new firmware because suddenly it does not >>see the player anymore on an USB port...>>>>To be honest - if your support team would read the mails a bit more >>carefully we all could save a lot of time... And of course I did >exactly>>as described by you and in the update notes. And this all on two >>different computers with two different OS - XP and Win98 as I said in >my>>first mail already...>>>>Best Regards,>>>>Peter>>>>>>>>At 02:6 .0.05 +000, you wrote:>>>Dear xxxxxx>>>>>>Thank you for replying to us.>>>>>>In response to your email, kindly ensure that your player is used on >>the>>>minimum operating system requirement. When connecting your player >>>directly to the computer, was your player being recognized? I have >>>verified the firmware update.>>>>>>Kindly verify the below steps you have used to update the firmware for>>>>>your player: >>>. Download the MuVoTXFM_PCFW__8_02.exe file into your local hard >>>disk.>>>2. Connect your player to your computer.>>>3. Double-click the firmware upgrade file.>>>4. When prompted to set your player in Recovery mode, disconnect your
>>>player from your computer. Press and hold the Play button while >>>connecting your player to your computer's USB port. Continue to hold >>the>>>Play button for about 0 seconds after connecting your player to your
>>>computer. Release the Play button when the Find New Hardware dialog >box>>>>>>>appears on the computer screen. Did you encounter any issue?>>>5. Follow the instructions on the screen to install recovery drivers >>for>>>your player.>>>6. Double-click the firmware upgrade file and follow the instructions
>>on>>>the screen.>>>>>>Are you still encountering the same issue?>>>>>>Do email back on the status concerning the issue so that I can assist
>>>you further. Thank you. >>>>>>Best Regards>>>>>><name removed>>>>Technical Support>>>Creative Labs Asia>>>>>>To provide feedback on your "Creative Experience" please click on the
>>>following link:>>>http://www.**bleep**.com/support/contact/welcome.asp?r=CLA&d=TS>>>>>>========== >>>DISCLAIMER >>>========== >>>This email and any attachments may contain private, confidential and >>>privileged materials for the sole use of Creative's intended recipient>>>>>and is not to be forwarded or copied to others. Any review, copying >or>>>>>>>distribution of this email or any attachments by others is strictly >>>prohibited. If you are not Creative's intended recipient, please >>inform>>>Creative immediately by responding to this email and thereafter >>>permanently delete the original and any copies of this email together
>>>with any attachments. Thank you>>>>>>Original Message Follows:>>>------------------------>>>Thanks for your response. I am a bit confused since I answered many of>>>>>your questions in my last mail already. And I have been working with
>>>computers for more than 30 years and did many upgrades with THIS >player>>>>>>>already. Since other users have exactly the same problem - if you >check>>>>>>>the forum - it must be a problem with the player or your upgrade >>>software. Should I send the player to your company for repair? But in
>>>any case - you should warn the customers using this upgrade or take it>>>>>from your webpage. If you read my old mail - I tried the whole upgrade>>>>>on 2 different OS and 2 different Computers with your latest drivers.>>>>>>Best Regards,>>>>>>Peter>>>>>>>>>At 07:38 0.0.05 +000, you wrote:>>>>Dear xxxxxx>>>>>>>>Thank you for reaching us at Creative Technical Support; we >appreciate>>>>>>>>the opportunity to assist you.>>>>>>>>Based on the information you provided, may I know if are you using >the>>>>>>>>player on Windows XP>>>> or Windows 98? I would like to inform you that the player only >>support>>>>>>>>>>the below operating system:>>>>>>>>Microsoft? Windows? 98SE/2000/Me/XP>>>>>>>>You might like to consider the below factors when connecting your >>>player>>>>to the computer's USB port:>>>>>>>>. Make sure you have the latest drivers, especially USB, installed >>for>>>>your motherboard. If you're not sure, check with your motherboard >>>>manufacturer.>>>>>>>>2. Make sure your motherboard has USB v. ports, supplying at least
>>>>500mA to the USB ports. If you're not sure, check with your >>motherboard>>>>>>>>>>manufacturer.>>>>>>>>3. Try unplugging all other USB devices from the system.>>>>>>>>4. If you're using a hub, try connecting the product directly to the
>>>>onboard USB and vice versa.>>>>>>>>5. You might wish to verify the functionality of your product on >>>another>>>>computer.>>>>>>>>Do let me know the result.>>>>>>>>In case if you need any clarification, please do not hesitate to >>>contact>>>>us. Thank you.>>>>>>>>Best Regards>>>>>>>><name removed>>>>>Technical Support>>>>Creative Labs Asia>>>>>>>>To provide feedback on your "Creative Experience" please click on the>>>>>>following link:>>>>http://www.**bleep**.com/support/contact/welcome.asp?r=CLA&d=TS>>>>>>>>========== >>>>DISCLAIMER >>>>========== >>>>This email and any attachments may contain private, confidential and
>>>>privileged materials for the sole use of Creative's intended >recipient>>>>>>>>and is not to be forwarded or copied to others. Any review, copying
>>or>>>>>>>>>>distribution of this email or any attachments by others is strictly >>>>prohibited. If you are not Creative's intended recipient, please >>>inform>>>>Creative immediately by responding to this email and thereafter >>>>permanently delete the original and any copies of this email together>>>>>>with any attachments. Thank you>>>>>>>>Original Message Follows:>>>>------------------------>>>>=======================>>>>>>>>Subject: CLA (CTL) - Technical Support Request - (MuVo TX FM)>>>>Name: xxxxxx>>>>E-mail Address: [email][email protected]][email protected][/url]>>>>Country: Thailand>>>>Self Description: Advanced PC User>>>>------------------>>>>Support Inquiry: ID(3) My Creative hardware stopped functioning >>>>correctly >>>>Product: MuVo TX FM>>>>Serial Number: C6PF32477002804Z>>>>Date Of Purchase: /2/2005>>>>>>>>------------------>>>>Operating System: Windows XP>>>>Creative Model Number: MUVO TXFM 52 MB>>>>Computer Brand/Model: >>>>Processor/CPU: >>>>Memory: >>>>BIOS Type/Revision: >>>>System Board/Chipset: >>>>------------------>>>>>>>>Detailed Problem Description:>>>>I tried to update to the latest firmware >>>>MuVoTXFM_PCFW__8_02 since I stay in Thailand >>>>and need the Thai letters. I installed the >>>>recovery driver since the upgrade software >>>>required this and did exactly what is described. >>>>After installing the recovery driver I run the >>>>firmware update again. It says that it found a >>>>device in recovery mode and more (pretty quick >>>>message) and after this it searches for this >>>>device - and does not find any device connected >>>>to an USB port.>>>>>>>>I have tried this many times and even with the OS->>>>Win98. The upgrade software detects the device in >>>>recovery mode but after this nothing more >>>>happens - it does not find it on an USB-Port >>>>anymore. >>>>>>>>=======================
Moderator note: Please remove the name of the advisor when posting up e-mails.
Message Edited by Catherina-CL on 0-3-2005 2:4 PM

This is part of the message since you cannot post such a long message in posting.
This should show how lost you might be with your warranty. If you install the Firmware Upgrade .8.02 your player might be useless. There is no way to make it work again. Not really. If you understand what Creative seems not to do. So dear user - buy a new player. If you want to know what the solution is to make your player work again post here. If there are enough postings I will explain it here. Too sad that Creative does not do it. It is their job not mine... But again - I am not talking about a problem what is nice to have it solved. I am talking about a player that does not work anymore. If you do not want to wait for my solution just send your player for repair - it was not your fault that it does not work anymore...
This story with the great support was a test of Creative and will be used in a review. So be not surprised to find it somewhere else.
Here the Creative support story. The first mail is at the bottom. I had to make part and part 2 since you cannot post such a long message here.
To: Creative Labs Asia Customer Support <[email][email protected]][email protected][/url]>Subject: Re: CLA (CTL) - Technical Support Request - (MuVo TX FM) (KMM7755874I6636L0KM)Dear,I know the solution long time already. I just wanted to test the support at Creative. The problem is real and forces owners of your players to buy a new one since their playes get useless after the upgrade. Not only that Creative puts a faulty upgrade on their homepage - their support is good for nothing. But this was a test of the Creative support. I hardly can believe that Creative is not in the position to solve a very simple problem caused by Creative - what has severe consequences for their customers. But this mail story confirms exactly this. So my advice to any customers - stay away from this company and their products - what is the final result of my test. If you want to know the solution for the problem please contact me again - I am glad to help such a poor company :-)))) For free? I am not so sure...since my player was not for free too...Best Regards,PeterPS: The product is still within the "police period" of my dealer. And I did not just buy the product. If you ever read what your system tells you (what I had to enter) - it was long time ago.
At 03:48 3.0.05 +000, you wroteear PeterBased on the information you provided, since you have just bought the product locally, you may like to contact and check with the dealer firstfor their purchase policy period and see if the product is still within their policy period. If they are unable to assist you, do contact us so that we can assist you promptly in your issue. Thank you. Best Regards<name removed>Technical SupportCreative Labs AsiaTo provide feedback on your "Creative Experience" please click on the following link:http://www.**bleep**.com/support/con...asp?r=CLA&d=TS========== DISCLAIMER ========== This email and any attachments may contain private, confidential and privileged materials for the sole use of Creative's intended recipient and is not to be forwarded or copied to others. Any review, copying or distribution of this email or any attachments by others is strictly prohibited. If you are not Creative's intended recipient, please informCreative immediately by responding to this email and thereafter permanently delete the original and any copies of this email together with any attachments. Thank youOriginal Message Follows:------------------------Dear .,I am a bit confused. What does my problem have to do with buying it on an oversea/business trip? This you really have to clarify. And why do you need my contact number/residential address if you have my contact email address already? You want to come to me and bring me a new player?Would be fine :-) But since there are many others with the same problem there must be a better solution.But in any case - I bought it were I li've and not on a business trip - the dealer is just around the corner - but I guess with more than 30 years almost daily IT experience I have a bit more knowledge than him. Igave you the serial number and the date of purchase. I bought it in Thailand where I li've now. Best Regards,PeterAt 09:28 2.0.05 +000, you wrote:>Dear Peter>>Regards to your issue, may I know is the unit purchase locally or during>Oversea/Business trip? If the unit is purchased during oversea/business
>trip, kindly provide me with the information of the place of purchase, >your current location (residential address) and contact number so that I>will be able to provide you with the advice required promptly.>>Do email back on the status concerning the issue so that I can assist >you further. Thank you. >>Best Regards>><name removed>>Technical Support>Creative Labs Asia>>To provide feedback on your "Creative Experience" please click on the >following link:>http://www.**bleep**.com/support/contact/welcome.asp?r=CLA&d=TS>>========== >DISCLAIMER >========== >This email and any attachments may contain private, confidential and >privileged materials for the sole use of Creative's intended recipient >and is not to be forwarded or copied to others. Any review, copying or
>distribution of this email or any attachments by others is strictly >prohibited. If you are not Creative's intended recipient, please inform>Creative immediately by responding to this email and thereafter >permanently delete the original and any copies of this email together >with any attachments. Thank you>>Original Message Follows:>------------------------>Dear ,>>I was talking about Win98SE. I guess there is are not many people using
>Win98 anymore.>>The problem is that the player is in recovery mode already. When I plug
>it into the USB port it does not show up as a dri've anymore. But the OS>confirms that I have put in a device into the USB port when I plug it in>pressing the play button. Also when I run the upgrade software it says >that it has found a device in recovery mode but then it does not find it>anymore. But again - neither WinXP nor Win98SE allow me to format the >dri've since it does not show up as dri've at all.>>Sorry for all this. But realize that I and many others have a piece of >scrap as long as we cannot find a solution for this problem. In the >forum people write that they even bought a new player already since this>firmware upgrade made an end to their TX FM.>>Best Regards,>>Peter>>At 03:0 2.0.05 +000, you wrote:>>Dear Peter>>>>Based on the information you provided that you have verified the player>>>>on another computer with Windows 98. I would like to inform you that >the>>player and the updated firmware only support the below operating >system:>>>>Microsoft? Windows? 98SE/2000/Me/XP>>>>I understand that you are also using the player on a Windows XP >>computer. However, you might like to verify your player on another >>computer that meets the above mentioned minimum operating system. Do >let>>me know the result. >>>>If issue persists but when connecting your player directly to the >>computer the player is being recognized, format the player using the >FAT>>file system, and download and install the latest >>driver/firmware/application update available through the below link: >>>>(Note: All contents in the player will be removed when you format your
>>player, please backup the files) >>>>http://www.asia.creative.com/support/downloads/ >>>>. Insert your MuVo TX FM player into the USB port on your PC/Laptop, >>try a different USB port or hub if it is not detected. >>2. Open Windows Explorer. The player will be recognized as a Removable
>>Disk. >>3. Right-click on the player and choose Format. >>4. In the File system drop down menu, select FAT, and then click the >>Start button. Do not select FAT 32, though it is selected as default by>>>>Windows XP. >>>>After the formatting is complete, make sure that you stop your player >>before disconnecting it from your computer. (Please take note that stop>>>>your player before disconnecting it from your computer is a must. >>Otherwise it will cause damage to your player's memory >storage/Harddisk)>>>>>>To stop your player in Windows XP, Windows 2000 or Windows ME Click on
>>the Safely Remove Hardware icon on the Taskbar, click Safely remove USB>>>>mass Storage device, and disconnect your play when you are prompted to
>>do so. >>>>Make sure that the icon below appears on the LCD screen again for at >>least fi've seconds before disconnecting your player.>>>>Do let me know the result. >>>>In case if you need any clarification, please do not hesitate to >contact>>us. Thank you.>>>>Best Regards>>>><name removed>>>Technical Support>>Creative Labs Asia>>>>To provide feedback on your "Creative Experience" please click on the >>following link:>>http://www.**bleep**.com/support/contact/welcome.asp?r=CLA&d=TS>>>>========== >>DISCLAIMER >>========== >>This email and any attachments may contain private, confidential and >>privileged materials for the sole use of Creative's intended recipient
>>and is not to be forwarded or copied to others. Any review, copying or>>>>distribution of this email or any attachments by others is strictly >>prohibited. If you are not Creative's intended recipient, please >inform>>Creative immediately by responding to this email and thereafter >>permanently delete the original and any copies of this email together >>with any attachments. Thank you>>>>Original Message Follows:>>------------------------
Moderator note: Please remove the name of the advisor when posting up e-mails.
Message Edited by Catherina-CL on 0-3-2005 2:43 PM

PETITION: This is what I would like to see in a new firmware upgrade for the MTP ZEN TO

FIXES:
-Ensures correct playback on the player of Zencast audio content that has been transferred using Zencast organiser. Remaining time is displayed correctly, and rewind / fast-forward functions can be used
- Allows users to transfer tracks between folders on the player when using a program such as Creative Mediasource [THIS IS NEEDED FOR ALL MTP PLAYERS]
- Allows charging via USB when the player is not being used by a program or is low on battery [THIS FEATURE SEEMS TO HAVE BEEN REMOVED BY MTP UPGRADE]
ENHANCEMENTS / ADDITIONAL FEAUTRES [I HAVE LISTED THESE BY MY PERSONAL ORDER OF PREFERENCE]:
) Allows the playback of Audible content types ,2,3,4 on the player, via a plug-in in Audible Manager
2) Adds bookmarking feature to the player
3) Adds SmartVolume EQ feature to the player
4) Adds DJ menu to the player
5) Allows user to partition a section of the player for data transfer
6) Allows user to synchronise tasks from Outlook to the player
7) Allows TXT files/ Ebooks to be stored/ viewed on the player
8) Adds BassBoost EQ feature to the player
PLEASE SIGN THIS PETITION TO URGE CREATIVE TO INTRODUCE AT LEAST SOME OF THESE FIXES / FEATURES IN A FIRMWARE UPGRADE FOR THE MTP ZEN TOUCH - also please feel free to add other suggestions that would improve the functionality of the Zen Touch
Message Edited by joshua32 on <SPAN class=date_text>05-30-2006 <SPAN class=time_text>:7 PM
Message Edited by joshua32 on 05-30-2006 :8 PM

all of these would be awesome, as would lyrics support, I REALLY want that

No power after firmware upgrade on nomad jukebox zen xtra

I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

Firmware upgrade for WRT54G v7

is there no firmware upgrade for WRT54G v7? i didn't even find version7 as listed in linksys page for routers....

Click on Download and save the file on your Desktop..
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use dmin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab-Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...Wait for few seconds until it shows that "Upgrade is successful" After the firmware
upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Firmware upgrade times out (BEFW11S4 v4)

Hi, my firmware upgrade times out everytime and i've read that the only way to get past this is by flash-upgrading the router through this web address ftp.linksys.com/pub/network but the link doesn't work for me and says '550 failed to change directory'. Is there another link i can try or another solution?
Previous thread: http://forums.linksysbycisco.com/linksys/board/message?board.id=Wireless_Routers&thread.id=122275

Download Firmware 314 KB...
Download TFTP Utility...
After downloading the Firmware rename the file(like - befw11s4)...
Follow these steps to upgrade the firmware on the device : -
Double click the TFTP.exe file and click run.
For Server- Enter the IP Address of the router that you assigned. By default, the router is 192.168.1.1...
For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
For File- Click the triple “…” button and browse for the .bin firmware file...
Click Upgrade button to start upgrading. A progress bar should show up to show the progress.
Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Firmware-upgrade failed router not accessible

during firmware-upgrade the connection to E4200 got lost due to power-outage, now the E4200 router is not accessible, power-led flashes ...
the factory-ip-address 192.168.1.1 responds on ping, but nothing else ...
how to get a working environment back?

Once reset the router. Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
Once the light gets stabilize on the router perform the following steps:
# Open up the browser and on the address bar type 192.168.1.1, it will prompt for the username and password. Provide the username as 'admin' and password as 'admin' or 'password'. Then it will open up the Router setup page.
# Then click on status and check the firmware version. If its not updated then upgrade the firmware once again.
# Then after firmware upgrade reset the router again as explained above.
Then uninstall the existing Cisco connect software from the computer. After uninstallation then configure the router again using Cisco Connect CD as you did earlier.

Firmware upgrade stuck

My router says there is still a firmware upgrade in progress. I have flashed and reflashed (using UI and tftp util) multiple times, and this will not go away.
This is all on top of erratic behavior, dropping the connection, periods of no connectivity, periods of degraded performance, etc.
I've tried a factory reset, and holding the button in for 30 seconds. Nothing will get this perpetual firmware upgrade to go away.

Anytime a firmware upgrade is interrupted (for whatever reason) before it completes, there is a serious risk that your router will die. However, there is always some hope. Please try the following:
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 08-25-2007 03:43 AM

Firmware Upgrade - OLD Text Messages/Photos Appearing BEFORE I Text

I recently went through the Thunderbolt Firmware Upgrade. All is well EXCEPT when I go to answer a text message. BEFORE I start typing, old messages and photos that I had sent to a totally different recipient months ago, are already entered into the response text box. I have to back out (back space) to get rid of text or I have to delete an arbitrary photo which was AUTOMAGICALLY inserted for me!
Not only does this waste my time, it can be very confusing! I could also inadvertently send private photos or private texts which were meant and sent to someone else MONTHS ago, to someone they were never intended for....!
Anyone else have their text messaging being hijacked by the operating system since the recent firmware upgrade??
Not sure who is responsible for the fix on this but, from what I see on this forum, I am lucky by comparison, to the other issues being experienced by those who updated their firmware (2/11/2013) when Verizon forced it onto us.
THIS NEEDS TO BE FIXED! Does no one BETA TEST these upgrades before they are forced upon us?

Hi Loonlady!
I understand your concern w/your messaging! I use messaging all the time and would not be happy either. I have some troubleshooting steps for you. Please give it a try and keep me posted:
Wipe Cache Partition
Before booting into Recovery, ensure that fast boot has been turned off:
1. Tap Menu
2. Tap Settings
3. Tap Power
4. Uncheck the box for Fast boot.
Once fast boot has been turned off, reboot into Recovery to wipe cache partition:
1. Power off the device
2. While holding down the Volume Down button, press the Power button. The device will boot into the bootloader which is a white screen with 3 Androids at the bottom screen.
3. Using the Volume Down button, select RECOVERY
4. Press the Power button to select the option. Device will reboot into a black screen with a red exclamation mark in a red triangle atop a device.
5. Press Volume Up and Power button to get into the Recovery menu.
6. Using Volume Down button, highlight the Wipe cache partition option.
NOTE: Be sure that Wipe cache partition is highlighted. Do not choose Wipe data/factory reset as this will result in loss of data!
7. Press the Power button to select the option
8. When the process, is complete, ensure that Reboot system now option is highlighted.
9. Press the Power button to select the option and reboot the device into the OS.
Christina B
VZW Support
Follow us on Twitter @VZWSupport

Firmware upgrade interference?

Is it possible that a firmware upgrade file can interfear with a printer causing it not to print? Can it also interfear with the computer getting those automatic updates for windows xp? This computer is wired to the router. I was told you can delete the file once the firmware upgrade worked. How do you do that? Thanks for any help that anybody can give me.

It is a well known fact that if a firmware upgrade does not install correctly or completely it may cause various problems. This LINK will show how to properly upgrade your firmware. When you flash it DO NOT refresh the routers settings with a back up copy from before the firmware upgrade. You must reconfigure the complete router settings for the type of internet connetion they are using.
To delete the .bin file (or any other file) you can right click on it then delete it.
Message Edited by Ikester on 12-02-2007 10:54 PM
Richard Aichner (Ikester)

Help..I updated my iphone4 to iOS to 7.1.1 from 6.1.3 at last stage of firmware upgrading throwing an error 16 and stuck in recovery mode.

HIAll
I waited so long not to update of my iphone4 to 7.x.x because of bugs and not much stable for iPhone4 and many reviews from friends saying phone is very slow and many bugs but after release of iOS 7.1.1 of many improvements for iphone4. I tried to update my iphone4 to 7.1.1 through iTunes at last stage of firmware upgrading its showing an error occurred error (16). I checked in internet error16 is purely hardware issue before my phone is very good condition in iOS6.1.3 no problem with my phone, But after upgrading to how it will be hardware issues. why Apple engineers are not testing properly their software’s before releasing great updates to customers now my phone is out of warranty and I can’t use it anymore just showing iTunes symbol and charger on the screen while on/off showing apple logo. From the past September there is no proper solution for error 16. Don’t know what these people are doing about that error why apple is crashing customer phones by releasing useless update to phones what is the point of buying such a expensive phones don't know what to do with this phone. Tried many possible ways
Tried: presing home+power button at 95% of firmware update
          Disconnected battery and restored
          used DrPhone to restart
          tried to restore old version 7.x.x
          no luck.
          used new original cables
          restored with Macbook
          tried to restore in 3 Different computers and so many times but no luck

Hi, to get your iPhone 4 back to normal, here're two ways for you.
1. Use Dr.Fone for iOS. The free trial version can fix iPhone screen of death. The free trial version can do that, you don't have to pay.
Just download and install this software on your computer and connect your iPhone 4 to computer with a USB cable. When it detects your iPhone 4 is abnormal, click Restart the device to get your iPhone 4 to be normal.
2. Use iTunes to fix it.
Step 1. Make sure that the latest iTunes is installed on your computer.
Step 2. Plug into a USB cable to connect your iPhone4 to computer.
Step 3. Press and hold the Home button and the Sleep/Wake button at the same time for about 10s.
Step 4. 10 seconds later, release the sleep/wake button. But continue to hold the home button until a message comes out, saying "iTunes has discovered an iPhone 4 in recovery mode, you must restore this iPhone before it can be used with iTunes".
Step 5. Click your iPhone 4 in the left sidebar to show the device control panel on the right. Then, click Summary.
Step 6. Go to Backups section and click Restore Backup.... In the drop-down list, choose a backup file and restore to your iPhone 4

Avoiding Firmware Upgrade Grief

Assuming that you have a non-UDP (User Data Preservation) phone, like the N95, a firmware upgrade can be a major thrash. Many posts in this forum attest to these problems, but they continue to occur, in part because of inadequate instructions.
Here are some thoughts that might be helpful:
1) FIRST: Ask yourself "WHY am I doing this?" If your aren't looking for any specific fix that you KNOW the firmware upgrade will address, then at least admit that you are possibly doing it "just because it's there." For those of us who have no other Everest in sight, that might be sufficient reason. But, it is a violation of the "If it ain't broke, don't fix it" maxim. I know you know.
2) SECOND: If you are still going to do this, make the appropriate backups. Plural. In spite of the rather glib advice on the firmware upgrade screen, backups to your Memory Card are NOT/NOT equivalent to those made with Nokia PC Suite. I'll explain why in a bit. Sure, go ahead and do both, but the Nokia PC Suite backup is the (only) one that will be likely to get you out of the woods. And that, only partially.
a. Backups to a Memory Card give you NO CONTROL over what is backed up OR restored. It's all or nothing, and sometimes what's included in "All" is just enough to trash your newly-updated phone.
b. Backups with Nokia PC Suite allow YOU to CHOOSE both what you want to backup and restore. So, backup everything if you like, but realize that you NOT successfully restore a highly customized system in one fell swoop after a firmware upgrade. But you CAN get back the essentials (if you have made the backups). By "essentials," I mean user-created data that you could not recreate easily or at all (contacts, messages, etc.). I do NOT mean specific applications, which you should be able to reinstall separately.
c. What about all of those Nokia Maps locations? Go to your Landmarks application, select every one you might ever want to see again, and then SEND them to another compatible Nokia phone via Infrared. Save them all on the second phone (you can reverse the process to get them back on your main phone). Wait: You are thinking about a firmware upgrade and have no comparably functional backup phone? Please reread item 1) above
d. Did you have to do any MANUAL configuration of Packet Data Access Points? I did before I could get my N95 to work as a modem for other devices. Write those details down somewhere. You'll need them. Same for WPA encryption keys and SSIDs. Consider putting this info in the fields of one of your contacts, so you can later use cut/paste to enter your encryption keys for your APs.
e. Make a list of every purchased application you have currently installed, even if you don't intend on using them again. Make sure you have product registration codes available. You'll need them.
Attempts to do an overly-comprehensive restore after firmware upgrade can cause serious problems such as loss of both 3G and WiFi data connectivity. That should be enough to get anyone's attention. It got mine after the fact! If you make careful, incremental backups of crucial information and are willing to be patient, you can eventually get your system back the way you want it.
3) BACKUPS all done? Too bad Nokia provides no verification process outside of the PC Suite log, but it usually works well-enough without it.
4) UPGRADE your firmware. Follow all of the advice and cautions but don't believe the part about a backup to your SD card being remotely adequate. It might be, but most likely only if you have very little customization and no or few third-party apps.
5) NEXT: Get your basic settings (time, date, etc) right.
6) THEN: Connect to PC Suite and RESTORE only your Contacts and Text Messages. Confirm that all restored.
7) NOW: Insert your SD card and IMMEDIATELY set your own PW for the card (if you had previously removed it). If you had applications on the SD card, some might work, others won't, and you'll probably get an "Installing" message followed by an error message to the effect that the applications could not be installed. Ignore the message to try to restore them yourself from the card. Don't (usually) bother to try to remove them, either, as that often doesn't work.
8) THEN: Recreate your WiFi connections and (if your provider-issued APs aren't right) your Packet Data APs. Make sure they work. Test by using your browser. No point trying to install products which require working data connections as part of the install process (e.g., gMail, Truphone) before confirming that such connections are available.
9) ALMOST DONE: Start reinstalling all of your prior applications. I suggest (if you have the choice) that you put them where they were before (SD Card or internal phone memory). If there are any you want to ditch, go back and remove them after first reinstalling them. That tends to get rid of the nagging "Installing" message.
10) FINALLY: Take it slowly, and set priorities. Put your essential apps on first, and remember that much of your customization probably took place over a period of days, weeks or months. Cumulatively, that might represent hours of tweaking. Re-tweaking will take no less time. Spread some of it out for your own sanity.
What have I forgotten? Probably plenty, and I'm sure someone else might be able to provide other, equally valid approaches, or suggestions which complement those offered above.

Very useful post. However I have to say that all those steps are necessary even if you have a FP2 phone with UDP. From my experience all that UDP does is to screw up your phone even more after a firmware upgrade. It's always better to start with a clean slate anyway
Message Edited by island3r on 04-Jul-2009 09:02 PM
N78
5800XM

N73 Firmware upgrade--- bad working Voice dialing

I updated the firmware of my Nokia N73 from 268.0.0.3 to 368.0.0.1. With the older version delivered by the phone voice dialing worked. In the 268.0.0.3 I only could given voice command for the profiles not for the contacts. It didn't recognise any contact. Because of thos I decided to do the next firmware upgrade to 368.0.0.1 and now the voice dialing doesn't work at all. Each time I put the button to activate it tells me "fualty voicesystem"in dutch "fout spraaksysteem. Now it became even worser. Is there anyone who helps me out?
regards

16-Dec-2006
03:34 PM
conradus wrote:
Thank you for your reaction. I put the firmware for the second time to my phone. Now it seems working again. When I touch the button for voice dialing it works untill then. But I may ask for every contact in my contactlist but nothing happens. When I touch the button again it is not reacting then but only the second time. When i asked for an other profile it sometimes works. In my contactlist it is possible to hear the contactname. But via voice dialing none of the contacts to choose.
best regards
Voice Dialling seems to be a bit choppy on most of the N-series models, because they use speech synthesis. Whereas this works for profile names, it's a different tackle for contact names. This is because contact names are assigned by assigned by you, the user. If you select Play Voice Tag for any given contact in your phone, it will output this name using speech synthesis. You will have to EXACTLY copy this output. And, if the name of a certain user is "John Doe Geralds", it wouldn't suffice to simply say "John Doe". You'd HAVE to put Geralds behind that, and in the EXACT same way as the device says it.
The only way to change a voice label for any given name is to change the name itself. The same goes for profile names and commands, but I wouldn't change these as the defaults work fine.
A reason because of which voice dialling may not work can also be found in the user's voice details having become useless for the phone. To correct this, go to Tools> Voice commands > Options > Settings and choose: Reset Voice Adaptations. Note that carrying this out means that ALL data collected about your voice shall be lost; you might have a bit of difficulty using voice features the first couple of times after performing this instruction. Beware to EXACTLY copy whatever the phone says, even though you know real-world pronunciation to be different. Until now, I haven't had to actually adjust the pitch of my voice to the synthesizer's pitch, but I know this would improve recognition accuracy.
Oh yeah... Sorry for my late reaction!
Best regards,
V3.0704.1.0.1
19-01-2007
RM-133 Nokia N73(57.01) Product Code:0539338

Muvo TX FM 512MB: firmware upgrade failed. How to recov

Hi, I have a Muvo TX FM 52MB. The firmware version used to be .4.0x. I tried to upgrade it to the newest one, .7.04.
I did everything according to the Instructions on the Creative Download Website. I let the OS to choose the recovery driver for me. The firmware upgrade file correctedly found my player and executed the upgrade. However, there's no instruction that I should check the format data option during upgrade. So I didn't format the data during upgrade. After the upgrade, I couldn't start the player and the PC couldn't recognize it.
I tried to do the upgrade again. The PC correctly recognized the player as a recovery device. After I started the creative upgrade program, the program founds the recovery device, then started to find any device connected to the computer, finally said that "The device is not connected to the USB port".
How to solve it's Many thanks.
Alex

go to nomadworld.com and find the firmware... READ PROPERLY... it says that u must install a new driver before u upgrade the firmware... mine works... for now, to recover it, press and hold the play button on the player while connecting it and hold the button until a window appears to install the player recovery software... before that, install the new driver first. then let windows search for the driver. windows will clear everything up in ur player. NOW U CAN DO UR firmware update... it doesnt matter whether u want to format or not cause the firmware upgrade program will format your player even though u didnt want to do it. its not the formatting problem.. hope this hel
ps.
thanks for reading.

Firmware upgrade correct steps?

Similar Messages

Maybe you are looking for