Firmware upgrade failed, printer now say i has firmware version 0. attention light lights up

Hey all
I had a problem printing a pdf on my mac, and then tried to upgrade my mac driver and printer firmware.
But the firmware upgrade failed for some unknown reason. And now the printer just have the ready and attentions lights on constantly.
I have tried to restart and reset the printer many times, and tried the HP firmware upgrade utility several times, with no luck. It just say it was "failed to upgrade"
Any idea what to do ??
My printer is a HP Laserjet Pro CP1025nw
Thanks
Jan

Hello Jan
It definitely sounds like the firmware update failed. Firmware is like a devices Operating System. Without it, it can't do much. This is backed by the "failed" message and that your printer reports it has version 0.
The printer will need to be serviced. Please call HP Phone Support at 1-800-474-6836.
Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
When a solution is found please mark the post that solves your issue.

Similar Messages

Vision:M - "Firmware upgrade failed!&qu

After spending several long, long hours rolling back WMP, trying different USB ports, installing and uninstalling various software, and borrowing friends' computers, I FINALLY got the firmware upgrade software to recognize my mp3 player. With great delight and an intense feeling of satisfaction, I clicked the "Upgrade" button and waited for several minutes, only to get a "Firmware upgrade failed!" message. I've tried the "Reload Firmware" option more than once, only to receive the very discouraging "Harddisk Problem". I've tried everything I can think of, from formatting to rebooting to resetting to reloading, but to no avail. I'm now left, like so many others, with a $300 bookend. Now what? I'm completely demoralized.

Well, being the stubborn person that I am,?I didn't listen to your advice andYesterday, against all odds from what I read on this forum, and being told that I would end up with an expensi've paperweight,? I decided to take the plunge and upgrade my Zen Vision M 30MB. ?I downloaded the newest firmware .6, saved it on my laptop which runs WMP 0, disabled all applications, including Norton and virus and spyware programs, as well as Creative's detector, connected my Zen Vision M to the USB dri've, double clicked the new firmware file, and followed the instructions. The new firmware started installing, within 3 minutes my player rebooted and then the library started rebuilding and within 5 minutes the process was SUCCESSFULLY COMPLETED!!!!!My player is working better than ever, it has all the new upgrades, album art, never went into Recovery Mode, and most important of all, I didn't lose any of my 2500 songs, hundreds of photos, slideshows and numerous videos, even my personal wallpaper and themes remained the same. I subsequently took the player to my desktop which runs WMP to test it'sand lo and behold, my player was immediately recognized, i transferred music and pictures without any problem and my player is now drag and drop compliant ?through Windows Explorer. My faith in Creative is unfaltering, I also own a MUVO TX FM, a Zen Micro and a Zen Sleek Photo and never had any problem with any of them.

After installing a new upgrade my computer now says...

After installing a new upgrade my computer now says QuickTime version 7.0d0 is installed, iTunes requires Quicktime version 7.0.3 or later.
Please reinstall iTunes.
So... won't that erase all of my music?and is it talkin bout the silver cd that says ipod on it?

hi Donnie!
first let's try a careful standalone QT 7.0.3 install:
b noir, "QuickTime Installation FAILED!! "Error Code: -1"" #1, 10:31am Oct 22, 2005 CDT
keep us posted.
love, b

Connected ipad to win 7 computer to upgrade it thru itunes. Says ipad has latest version but did not install correctly. Appear to have lost everything

Connected ipad to win7 computer to upgrade os as I needed to download an app. Says it has latest version but it did not install correctly. Ipad says hello,asks for language and location,wi-fi then options are set up as new ipad,restore from icloud or itunes backup. I think I have managed to backup over my good backup and lost everything. Ipad will not boot HELP

Hello RodneySmart,
Thanks for using Apple Support Communities.
From what I understand about your issues is that your iPad will currently not turn on. In attempt to resolve this issue please follow the steps in order below:
Resolution
If a single application is not responding or stops responding when it opens, you can force it to close.
If the device is unresponsive or if certain controls aren't working as expected, restart your device.
If the device remains unresponsive or does not turn on (or power on), reset your device.
If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
Let it charge for at least twenty minutes, then see if it starts normally.
If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
If the screen displays a red battery icon, continue charging the device until the battery is fully charged. Learn more about charging iPhone and iPod touch, or iPad.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Take care,
Alex H.

Creative Zen Microphoto - "Firmware upgrade failed&qu

Hi,
two days ago my Zen Microphoto started in "Recovery Mode".
I had no means of getting out. I first selected "Clean Up" and rebooted, still "Recovery Mode".
Then I downloaded the latest firmware version for it:
ZENMicroPhoto_PCFW_L6__3_0.exe
Then I selected "Upgrade Firmware", acknowledged with "Yes", the firmware was deleted, but the windows firmware application said "no player connected" after connecting the player.
Okay, after googling a bit, I found out that I needed to downgrade from WMP to WMP 0.
I (painfully) did this and after installing an additional Registry Key via fixup.cmd the
ZENMicroPhoto_PCFW_L6__3_0.exe
detected the player (hurray!). It showed "Current Player Firmware Version .20.0 " and "Upgrade File Version .3.0".
When clicking on "Upgrade" at the windows application, the blue progress bar appeared and the player showed "Recovery Mode" and a blinking USB logo.
What it did NOT show afterwards was a gear symbol with "Upgrading firmware" (which I found on a screenshot in the internet).
When the blue progress bar of the windows firmware upgrade application reached about 85% it halted and after minute the windows firmware application showed "Firmware upgrade failed!" while the player only showed a black screen with "Recovery Mode" and the green battery symbol at the top.
I also tried the same procedure with
ZenMicroPhotoP4S_PCFW_LB__20_0.exe with the same result: "Firmware upgrade failed!"
Any ideas how to "repair" the player
Toddl
Message Edited by Toddl on 04-2-2008 09:40 AM

I have this same problem except with the Zen Vision: M. Any help would be appreciated.

Firmware upgrade fails

I am having trouble upgrading the firmware on my WRE54G. My hardware is v.3 and the existing firmware is 3.01.01.
I downloaded the latest firmware and extracted the .img file. I went to the admin page of the expander, pointed it towards the new firmware, and hit "go." After a minute or so it said something like:
Firmware upgrade fail.
Fail!
No reasons are given.
Anybody have any idea what is going on?
Thanks,
Garth

I had a similar problem upgrading firmware with my WRT300N. What i did to solve the problem was first i downloaded and went through the winzip program given for the router, then i went back to the webpage of the router and retried the upgrade and it worked. I actually ignored by routers version, and downloaded and went through each winzip program and each firmware upgrade for every different version . **i only downloaded the firmware up to my version and my version**.
Message Edited by DaveY on 11-15-2007 07:01 PM

Was upgrading from Leopard to Snow Leopard. Install failed. Now says I'm in 10.6 but I'm incomplete. Screen goes gray. Can't boot from disk.

Snow leopard install failed. Comp says I have 10.6.8 but get gray screen when trying to install.

Run through this list of fixes
Step by Step to fix your Mac

Zen Micro 5GB Firmware "Upgrade Faile

Zen MicroFirmware: 2..02?Have just bought it from america, have tried installing both firmwares from the site, and both of them say "Upgrade Failed!" I havent installed any of the software from the disc except the Zen Micro driver, my pc didnt need this but i thought it would be best to. Also i can only add tracks to it through WMP 0, i cant drap and drop in windows explorer, why is this? On my old creative muvo n200 i could do this fine!?Some help please. Do i need to erase the firware in the recovery menu? I am just running the downloaded applications when my player has the docked icon on the screen.
Message Edited by ajay6 on 03-5-200607:28 PM

Thanks for help.
Major problem solved.
Already upgraded to new firmware.
I do it by:
1. uninstall all creative application and plugin.
2. using registry cleaner to clean the registry.
3. downgrade WMP to WMP0
4. Detected by WMP as MTP device, loading firmware upgrade, closed WMP. upgraded.
Now it Working fine already, just still have some problem is:
. Only WMP can detect it, all creative application can't detect it..
thanks anyway.

Muvo TX FM 512MB: firmware upgrade failed. How to recov

Hi, I have a Muvo TX FM 52MB. The firmware version used to be .4.0x. I tried to upgrade it to the newest one, .7.04.
I did everything according to the Instructions on the Creative Download Website. I let the OS to choose the recovery driver for me. The firmware upgrade file correctedly found my player and executed the upgrade. However, there's no instruction that I should check the format data option during upgrade. So I didn't format the data during upgrade. After the upgrade, I couldn't start the player and the PC couldn't recognize it.
I tried to do the upgrade again. The PC correctly recognized the player as a recovery device. After I started the creative upgrade program, the program founds the recovery device, then started to find any device connected to the computer, finally said that "The device is not connected to the USB port".
How to solve it's Many thanks.
Alex

go to nomadworld.com and find the firmware... READ PROPERLY... it says that u must install a new driver before u upgrade the firmware... mine works... for now, to recover it, press and hold the play button on the player while connecting it and hold the button until a window appears to install the player recovery software... before that, install the new driver first. then let windows search for the driver. windows will clear everything up in ur player. NOW U CAN DO UR firmware update... it doesnt matter whether u want to format or not cause the firmware upgrade program will format your player even though u didnt want to do it. its not the formatting problem.. hope this hel
ps.
thanks for reading.

WRK54G firmware upgrade fails: file pattern error.

When I attempt to upgrade the firmware in my WRK54G router, the upgrade fails with this error message:
Upgrade action is not finish!!
Upgrade file pattern error.
The linksys download page says the file size is 1.10 MB.
The size of the file I downloaded (WRK54Gv2_1_00_1) is also 1.10 MB (1,160,036 bytes). So it appears the file was downloaded successfully.
I had no problem upgrading the firmware to version 1.1.
Please advise.
Thank you

What is the hardware version of your router? Is it version 1, version 1.1 or version 2? Where did you download the firmware of your router? Is it from the US website.
On the US website you have 3 wrk54g, one is version 1, version 1.1 and v2.
"When love and skill work together, expect a masterpiece."

WRT350N- Firmware Upgrade Failed

when upgrading with .bin file (v1.05.8) via Administration - Firmware Upgrade, it fails when status showing 76% completion.
Please help what i need to do?
I already tried to boot in safe-mode to minimize programs running (firewall, etc), still showing Upgrade failed.
/v
Message Edited by viva on 10-20-2007 06:56 AM
(Edited subject to keep threads from stretching.
Thanks!)
Message Edited by JOHNDOE_06 on 10-20-2007 06:59 AM

Go to the control panel/network connections and right click on the local area connection. Click properties and roll down to highlight Internet protocol TCP/IP. Click the properties button and check "use the following IP address". Fill in 192.168.1.5 and tab through. The subnet mask will fill itself out to 255.255.255.0
make the preferred DNS server 192.168.1.1 (the router) and click okay.
If the computer succeeds in getting an IP address (verify this by opening a command window and typing "ipconfig" and seeing what it say under the local area connection), type ping 192.168.1.1 in the same command window and see if the router responds.
If so, you can use the TFTP.exe utility from linksys, available from linksysinfo.org at
http://www.linksysinfo.org/forums/downloads.php?do=file&id=4
Run this program, point it at the router IP 192.168.1.1 and show it the bin file you want to use. Might be a good time to use the released firmware rather than a beta. But that is your call. You can get the latest firmware from the linksys page.
If you are unable to ping the router, try putting the ethernet cable in a different port. Don't ask me why, but when my router bricked, it would only work on slot 4. Found this out by accident, but I was able to fix the router when I did this. If it does not work on any slot, you may be screwed. Call linksys and ask for a RMA to get a replacement. I would not tell them you bricked it with a beta firmware!

Linksys SRW224G4 firmware upgrade fail!!!

Hi,
I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
If is possible, I need that switch so a rapid answer will be appreciated!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x32d980 records...
Setting checksum: 0x19527ef1 , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
FAIL !!! Check image for valid file.
Please download a new image.
Here the result for
Downloading code using XMODEM.
-- Download complete --
Wrong file format. Writing aborted.
Perform WARM BOOT ...
Thanks,
Steve

I just tried updating the firmware in my SRW224G4 using the file "fesm-12216.ros" as indicated based on my bootloader version 1.0.0.06.
Now it's stuck in a reboot loop. Here is the log from Hyperterminal starting from the update:
Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
[6] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x2e4180 records...
Setting checksum: 0x1709abda , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from flash
100%
OK
Running from RAM...
*** Running SW Ver. 1.2.2a Date 05-Apr-2007 Time 15:35:50 ***
HW version is 00.00.02
Base Mac address is: 00:12:17:5d:08:d5
Dram size is : 32M bytes
Dram first block size is : 16969K bytes
Dram first PTR is : 0xF6D840
Flash size is: 8M
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
01-Jan-2000 01:01:08 %ERHG-F-SEND: BOXP_perform_smi_scan_of_devices_in_slot: inv
alid device type is found: 268374443 on device 0
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 1.2.2a (date 05-Apr-2007 time 15:35:50)
***************** SYSTEM RESET *****************
It just repeats this over and over. The unit is out of warranty. Can I do anything to get this switch back up and running?
Should I try reloading the firmware again or updating the bootloader?
Any help would be most appreciated!
Thanks.

Firmware-upgrade failed router not accessible

during firmware-upgrade the connection to E4200 got lost due to power-outage, now the E4200 router is not accessible, power-led flashes ...
the factory-ip-address 192.168.1.1 responds on ping, but nothing else ...
how to get a working environment back?

Once reset the router. Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
Once the light gets stabilize on the router perform the following steps:
# Open up the browser and on the address bar type 192.168.1.1, it will prompt for the username and password. Provide the username as 'admin' and password as 'admin' or 'password'. Then it will open up the Router setup page.
# Then click on status and check the firmware version. If its not updated then upgrade the firmware once again.
# Then after firmware upgrade reset the router again as explained above.
Then uninstall the existing Cisco connect software from the computer. After uninstallation then configure the router again using Cisco Connect CD as you did earlier.

Spa508 firmware upgrade failed

I bought a spa500ds and need to upgrade the firmware on my 508G to use it.
When I try to upgrade to 7.5.4, or 7.5.3 I get a failure. I was able to upgrade to 7.5.1a fine. All firmware was downloaded from cisco this morning and unziped
I see my tftp server giving the file.
I get upgrade failed: 12. corrupt file in my syslog
Any idea where to look next?

It states on the release notes of 7.5.4, that upgrading from 7.5.1a you should first upgrade the phone to 7.5.2b.
Have you done this upgrade step?
Joao

Zen Micro - firmware update failed so now "dead"

I have a firmware problem with my Zen Micro. Can anyone help?
The series of actions I have taken so far are these:
I got my Micro in January 2006. I now want to run Audible software to listen to their books so I downloaded the firmware update L6_2_2_02.exe from the Creative support site which is stated as providing the Audible?facility.
I backed up the Micro contents using Creative MeadiaSource Organiser. I then ran the firmware update from my Win XP PC. This started OK and I got a series of messages about what was happening. Then it stopped with the progress indicator bars about 2/3 across. I left it for half an hour and nothing changed so clicked to stop the update.
I checked the firmware version on the Micro and it said 2.2.02. The update?looked OK and the FM worked but of course I had no music content.
I opened my Creative MeadiaSource Organiser (v 3.0.09) but it said no device is connected so I was unable to reload the music. My XP PC recognised the Micro as connected and I checked Device Manager which showed the "device is working properly". I was also able to synch music to the Micro using Windows Media Player and this played OK. I tried another computer and could also synch using Windows Media Player but I wanted to reload my music from the backup.
I looked on the Creative site for the steps to take when a firmware update fails. The Zen Micro is not on the list as supporting the MP3 Player Recovery Tool so I did not use that. I followed the Reload Failure recovery instructions and ran Clean UP, then Format All, but this did not fix it so I ran Reload Firmware on the Micro. This was a big mistake!
Now when I try to run the firmware update from my Win XP PC, I select English then I get the message "Your player is not connected, please connect your player". I checked again and XP still recognises the Micro and the device is working. It is no longer recognised by Windows Media Player but just? appears to XP as an empty storage device.
The Micro now shows the firmware as v 0.0.65, but now it is stuck in Recovery Mode. I have contacted Creative Support but their reply is that this player is now over 3 years old, reached its end of service life, so there is no support other than on their web site. Following their web site recovery instructions got me into this mess so I guess?no extra help is offered from Creative.
The player is now essentially dead. Unless there is some way to get the firmware update program to recognise the device as connected, then I don't know how to fix this. This is a shame as it is a nice little player for my music collection.
Can anyone help as I don't know what to do next?

I have the same problem. I put the screenshots below and the errors that happen to me.I can not put him the firmware because I do not recognize the device.
Both windows xp windows 7 as the
DISPOSITIVO, IMAGEN ACTUAL
http://img528.imageshack.us/img528/3783/dsc0025mv.jpg
EL PORTATIL LO RECONOCE
http://img811.imageshack.us/img811/4323/dsc0026ox.jpg
MUESTRA BATERIA, PULSANDO BOTON DERECHO
http://img546.imageshack.us/img546/4855/dsc0027wj.jpg
ADMINISTRADOR DE DISPOSITIVOS
http://img801.imageshack.us/img801/4501/dsc0028une.jpg
ERROR AL INSTALAR CREATIVE SOURCE
http://img805.imageshack.us/img805/3061/dsc0029io.jpg
http://img208.imageshack.us/img208/9330/dsc0031sn.jpg
http://img545.imageshack.us/img545/7096/dsc0032qg.jpg
MP3 PLAYER RECOVERY TOOL, no me reconoce Creative ZEN MICRO como conectado
http://img528.imageshack.us/img528/1714/dsc0030qn.jpg
PROGRAMAS DESCARGADOS (pagina oficial creative)
http://img341.imageshack.us/img341/2466/dsc0033oi.jpg
DSC_0025.jpg
I need your help. I'm desperate. Uninstall Windows Media Player.
Thanks in advance

Firmware upgrade failed, printer now say i has firmware version 0. attention light lights up

Similar Messages

Maybe you are looking for