Firmware upgrade from 2.1(3a) to 2.1(3b).

I don't find any documentation on the web for firmware upgrade from 2.1(3a) to 2.1(3b)..
is it wise to follow this link http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/upgrading/from1.4/to2.1/b_UpgradingCiscoUCSFrom1.4To2.1.html
Any best practices ?

I would consult
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2.1/b_GUI_Firmware_Management_21.pdf
Cisco UCS B-Series GUI Firmware Management Guide, Release 2.1First Published:
Last Modified: July 12, 2013November 16, 2012

Similar Messages

SPA112 firmware upgrade from 1.0.1 to 1.2.1 kills the SPA

I took a brand-new, unconfigured SPA112 out of the box, plugged it into DHCP-enabled network, noted it was running v1.0.1 firmware and attempted a firmware upgrade to 1.2.1 via the web management utility.
After reporting a successful upgrade there was no further response from the SPA112 to HTTP requests, neither was there any response to pings. ARP requests are responded to successfully. The IVR works (as well as the IVR ever works) until I selected to perform a factory reboot at which point the IVR stopped responding as well. Holding the reset button for 20sec does nothing useful. It's dead, Jim.
I've had this experience on another SPA112 as well under similar circumstances although there is nothing in the Release Notes for v1.2.1 to say that such an upgrade does not work.
My questions:
1)Is there any way of recovering these devices or do I need to send them back to Cisco?
2) How am I supposed to perform such a firmware upgrade?

Hi Matthew,
I tried upgrading the firmware upgrade from v1.0.1 to v 1.2.1 and I had the same problem. The device just stopped responding. I tried that in a lab and I figured out what exactly to do when you get in to a problem like that. So lets start off once again.
Snce SPA112 must get an IP first through a DHCP on WAN port. Connect the SPA 112 device according to the instructins told in this article till the step 3.
http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=2775
Once you access the web GUI of SPA112 follow the contents of the following article and upgrade the firmware
http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=2676
In your case I believe the window got stucked at the point when it says "The upgrade is successful" and then there was no further response to HTTP requests.
Restart the device and see if it works or not. If it does not then log in to the router web GUI and navigate to the ARP table and see what are the VLAN assigned to the IP address.
NOTE: Both the router and SPA should be in the same VLAN. This way only the device will respond to the HTTP requests. If they are in a different VLAN's, navigate to the VLAN and disable the LAN memberships. For example there are two VLAN ID 1 and 100. Disable the LAN ports for the ID 100 and only enable it for 1.
Navigate to the ARP table again and refresh it. Both the IP addresses should be in the same VLAN. If yes. Access the SPA112 with an IP address assigned to it again and navigate to Administration > Firmware Upgrade. You will see the firmware of the device has been upgraded.
(optional) Upgrade the firmware again. This time, it will go through and the device will restart.
Let me know if you still need any help.

How the heck do i get a firmware upgrade from my computer to the router?

I went to this site here to try and make my router work. It is a WRT54GS wireless router, and I saw where i could download some firmware upgrade, so I clicked on it and saved it to my desktop. It is a .bin file. Now how do I get that file to the router?????
The router was working until today and now it isn't sending out a wireless signal. However, it is still connecting my computer to the internet through its wire (modem to router, router to computer with cable). But when I open the Easylink software, it says that the internet connection is not working, even though the little green light is on for "wireless" on the front of the router.
But anyway, how do I get this downloaded file onto the router??? There isn't any usb ports on the router to connect to it. There isn't anything in the Easylink software that gives me that option, or if there is they hid it pretty good. They really should explain how to do this, or do they expect everyone to have a degree in networking or computers or something? I need some help here

As sabretooth suggested,Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now,Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

BEFW11S4 v4 firmware upgrade from 1.45.3 to 1.52.02 failing

I've been having some problems with my router resetting so I decided to upgrade the firmware. I'm currently on version 1.45.3, Jul 1 2003 and I wanted to update to 1.52.02 4/07/2005. I downloaded befw11s4_v4_v1.52.02_000_FCC_code.bin from Linksys' site and selected it at http://192.168.1.1/Upgrade.htm. The progress bar will start to move and when it reaches about 75% I'm redirected to http://192.168.1.1/Upgrade.cgi which is a blank white screen . If I go back to http://192.168.1.1/ and check the firmware version I see 1.45.3 still. Does anyone have any idea what is going wrong?
Solved!
Go to Solution.

So I just went ahead and called the dreaded customer service.....turns out the filename just needs to be changed. There are 3 easy steps to fix this problem.
1. If its on your desktop the name should appear as BEFW11S4-v4_v1.52.02_fw,0 change it to befw11s4_v4_1.52.02_000_FCC_code.bin
2. Go to your upgrade firmware screen, click browse to get the file with the new name
3. Click upgrade and be happy that it worked!!

ASA firmware upgrade from console - tftp error

Have an asa 5510, trying to upgrade the firmware via console.
I have a tftp program installed on my PC but get an error running the command, any idea what I'm doing wrong?
asa# copy tftp flash
Address or name of remote host [142.xx.xx.xx]? ------------> IP of my PC
Source filename [asa912-k8.bin]?
Destination filename [asa912-k8.bin]?
Accessing tftp://142.xx.xx.xx/asa912-k8.bin...
%Error opening tftp://142.xx.xx.xx/asa912-k8.bin (No such device)

Hi,
You really cant upload files through the Console connection. Its not a network connection.
Your PC might have an IP address configured but that would be configured in its network interface card which has nothing to do with the console cable connection.
So you will have to configure one of the ASAs network interfaces with IP address and other basic settings. Then you need to configure the PCs network interface cards settings to match the IP address/subnet configured on the ASA. Then you will have an connection between the ASA and the PC and should be able to load the software to ASA.
For example
interface Management0/0
nameif management
security-level 100
ip address 10.10.10.1 255.255.255.0
no shutdown
and the configure the PC with IP address 10.10.10.100 and mask 255.255.255.0 for example and then load the software from the PCs IP address of 10.10.10.100.
- Jouni

NAC firmware upgrade from 4.1.3 to 4.7 or 4.8, anyone?

I currently have 1 CAS 3310 Failover Bundle for Wireless user, and 1 CAM Lite Failover Bundle for management.
ACAS, CAM and Clean Access Agents are running 4.1.3. We are considering an upgrade in particular because some end-users machine are soon to be Windows 7. Our authenticaion for users is provided by AD SSO.
I would like to know your experience when doing such a major jump (4.1.3 to 4.8.1). Looking for gotchas and known issues. Also what the incremetal upgrade path look like.
I was thinking we can go 4.1.3 -> 4.6.1-> 4.8.1. Any other way or recommendation. CIsco is highly recommending we go to 4.8.1 if all possioblem.
I am also aware that we need to create new root certificates.
Appreciate input.
Thanks,
Rosa

Hi,
Yes, that is the correct upgrade path: 4.1.3 -> 4.6.1 -> 4.8.1.
I would recomend you to go through the Release notes for 4.6.1 and 4.8.1 for all the known gotchas and detailed upgrade process.
Gotchas/changes/upgrade process for 4.6.1: http://www.cisco.com/en/US/docs/security/nac/appliance/release_notes/461/461rn.html#wp65900.
Gotchas/changes/upgrade process for 4.8.1:http://www.cisco.com/en/US/docs/security/nac/appliance/release_notes/48/481rn.html#wp65900.
Regarding the certificates, you should not use the self signed certs due to security reasons, and they should only be used for lab purposes.
This means that it still works with the self signed, but you need to import the CAS cert into the CAM trusted certification authorities and vice-versa, so that the CAM trusts the CAS cert and vice-versa.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

WLC firmware upgradation from 6.0.196.0 to 7.0.98.0

Hi,
I have not come across to upgrade the IOS of WLC at any time .
Right now , I have WLC 6.0.196.0 and it is working fine but still if in case I need to upgrade to 7.0.98.0 or whichever is latest , What is the procedure ?
How to go about it ?
kindly suggest me for the same.

Hi Vinod,
Sorry for the late reply.. this forum thingy is messed up.. suddenly this throws me off!! hav to re-login.. strange!! ok lemme get back..
Main image = The image helps you in getting the GUI and helps you in configuring through the CLI..
Boot Loader image = Is almost equal to ROMMON version on switches!! ok lemme explain u in WLC world.. When you reboot ur WLC, while rebooting if u hit "Escape" then you can see something like the Intial WLC config wizard.. or while doing the PASSWORD recovery we select options 1 to 5.. this is called as Boot loader version..
The complex explanation is.. A boot loader, also called a boot manager, is a small program that places the Operating System (OS) of a computer into Memory. When a computer is powered-up or restarted, the basic functions performs some initial tests.
lemme know if this answered your question and mark it as answered if so!!
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Firmware upgrades from Nokia Updater

Guys !
Hello Again
I was unable to update latest firmware through Nokia updator
when I had 11.0.034 firmware. I consistantly got this message "Your software is up todate" though 20.0.058 software was released. Will Nokia tell us why this ia happening ?
If my post has helped you please click the white star on the right

23-Nov-2006 12:38 AM babdi wrote: Guys ! Hello Again I was unable to update latest firmware through Nokia updator when I had 11.0.034 firmware. I consistantly got this message "Your software is up todate" though 20.0.058 software was released. Will Nokia tell us why this ia happening ?
Your post is unclear. The main reason for this is that you do not mention which phone you're using. Anyow, things such as this can happen because of two (2) reasons:1. You have a branded phone, which contains software customised by your operator
2. You have a CV-variant, where CV stands for Country Version or Country Variant.
If the former is the case, you will need to wait until your operator releases the firmware for your specific model; Nokia's responsibility ends here.If the latter is the case, you will have to wait a bit longer, as not all CV's have been added to the database yet. To find out whether you have a CV or not, post the FULL output you have when you press *#0000# on this board (in this topic), and e-mail your product code to Nokia (you may choose to also post your product code on the board.
V3.0704.1.0.1
19-01-2007
RM-133 Nokia N73(57.01) Product Code:0539338

Iomega StorCenter NHDD2 Firmware Upgrade from v1.27?

I hope you can help me;
I have an old Iomega NAS device that has performed flawlessly for as long as I can remember (2006 I believe?) but having attached a USB HDD to the rear it is only allowing read only access. Would a firmware update solve this?
If so, how would I go about it as the device does not show up in the LenovoEMC Storage Manager (v1.4.4.14439).
Thanks in advance,
Mac

Hello macaulay576
Is this a HMNHD? or HMNHD CE (2)? Could I have you provide the first two digits of the unit's serial number so I can confirm the correct device type?
If it is one of the HMNHD variants you should be able to modify the connected external drive's access permissions via the web interface.
If this is a device older than the HMNHD devices, you should still check the web interface for access permission options for the connected drive (it usually will show up as a share even on the older units) Firmware may help, but depending on the device an update may not be available any longer.
LenovoEMC Storage manager should be able to detect most legacy StorCenter devices, if it doesn't the unit may be too old to be detected correctly. you should then use your router or a network scan to detect the unit's ip address. the " arp -a " command will work in Windows and OSX to scan your local network and list the detected devices and their ip and mac/physical addresses.
You may also want to check here to see if there is any further suggestions on the forums.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Firmware upgrade from Verizon has caused errors.

I am unable to see contacts or use the phone. Contacts: application people (process com.android.htc contacts) has stopped unexpectedly. Phone: process android.process.acor has stopped unexpectedly.

Hard Reset is suggested....
http://community.vzw.com/t5/Android-Apps/After-the-Update-Somthing-to-consider/td-p/642367

Firmware upgrade crash

I've recently acquired my first BB, a Curve 9320 and when I linked it to the Desktop Software was enticed into carrying out a firmware upgrade from v7.1 bundle 1319 to v7.1 bundle 2039
After automatically running another backup, the upgrade crashed and bricked the device, which has had to be replaced under warranty. The replacement has the original firmware version on it!
Should I be tempted to try the upgrade again, or play it safe and keep what I've got?

Hey Sawbones,
Welcome to the BlackBerry® Support Community Forums.
I would suggest doing the update from a PC using the BlackBerry® Desktop Software, let me know if you need any assistance.
Thanks.
-HB
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

WRT45G firmware upgrade

The WRT45G operated flawlessly until a firmware upgrade from 3.0 to 4.2.1.1
Periodically, usually after a reboot - Internet (external) access is blocked, and attempts to adjust firewall settings, or restore saved settings fail to correct.
The only resolution I found - restore to factory settings - allows access to Internet.
NOTHING else is changed. Nothing has changed on the system except for the firmware update.
Any ideas how to roll back or to force the router to use the save settings appreciated.
Its XP - Linksys router and Cablemodem and router set to factory settings.
Firewall through XP

What is the exact version number of the router? Check on the bottom. Also after all firmware upgrades you are to fully hard reset the router by pressing the reset button on back for 30 seconds and release. Wait 10 seconds and power cycle the router. Now you must reconfigure the router from scratch, no backup files.

DMS 5.0 DMP Firmware Upgrade

I'm trying to use DMM 5.0.2 to push a DMP firmware upgrade from the server. I have done it before, but for some reason now when I go to create the "firmware upgrade" job I can't check the image on the list of "Available Assets". The checkbox just physically doesn't work. I have tried a couple of different browsers, to make sure it wasn't something browser-specific.
Anybody else seen this one? Is it just me?
Thanks!
Mike

I have the same issue. I have a DMM running 5.2.1, and I just installed a new DMP, out of the box with 5.1. So I tried the same thing.... First I went to DMP - Adv Tasks - Sys tasks, & created a new app for the firmware update, but it will not let me check the new firmware file that is sitting in the assets. I am new, and previously a firmware update had been done, and there is an App sitting there for the 5.2.1 update, but when I "edit" the application, it also shows no check in the box for the appropriate file. I don't know what to do at this point... will have to put a TAC case in. Let me know if you find the answer.

HP8600 Plus won't send or receive fax after firmware upgrade

Hi All,
Suddenly my HP8600, refuses to send or receive fax. I get the message "Can'r send or receive fax" immediatley after power up. I have a strong feeling that the problem started after an automatic firmware upgrade to version OJP8600_N911a_R1435A . Unfortunately there does not seem to be a simple way to downgrade or is there? HP refuses to tell. I have checked the telphone line and the connection also tested with another fax machine. I tried resetting several times without any success. It is just out of warranty and works perfectly in all other respects.
Do someone have any ideas?
Thanks in advance.
Bondra12

Hello @Bondra12 , welcome to the forums
I understand you now cannot send or receive a fax, and I am here to share my suggestions with you.
No, you cannot reverse a firmware upgrade from my knowledge. I would suggest however, troubleshooting the fax problem by trying out the steps from this guide: Cannot Send or Receive Faxes
If the problem does happen to continue, and I wish that it doesn't, to give us a call to see if you have any out of warranty printer options.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Best wishes,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

N96 crash during firmware upgrade & unrecoverable

Finally Nokia sent me a text to say that a firmware upgrade - from 10 to 11 was available. I've tried to install it after first backing up the phone. During upgrade where the upgrade software continually referred to connection problems (while the Nokia PC Suit showed the connection to be in place) with about 5 minutes of remaining installation time the installer gave up. It asked me to turn off the phone and reconnect which I did. The installer could not recover the installation. I now have a phone that will turn on but just has a blank screen and PC Suit won't recognise it so I can't restore from the backup.
Any ideas? Does my second N96 have to be sent back to Nokia?
This is all becoming rather silly...

B4 you update I found this improves the way it works
before you connect phone by USB
Plug in charger and leave in (make sure its turned on at the wall socket)
1st switch to line 1 if you have 2 lines
set profile on genral
turn off password on boot
turn OFF pincode request
turn OFF fixed dial
IF you have Lights ON installed uninstall it (you can put it back after)
if You have any other prog that RUNS all the time Like Lights ON unistall that too. (eg rotate me on N95)
TURN OFF PHONE
remove SD card
TURN ON PHONE to get a clean boot with nothing running in background
now make sure you connect in PC suite mode when you plug in USB
run P C suite click on Spanner TOOLS
go down to software update
NOW WAIT if it says there is a new version or it loads new drivers
there are 5 or 6 cable drivers that it MUST load before it starts it only does that once the 1st time
Now all will go well
most of the crashes are caused by either a prog running on the phone or the pin or password being set and the phone cant reboot or a flat battery
Message Edited by ivor_bigun on 11-Nov-2008 05:27 PM
Nokia user / modder since Nokia Orange and Mobira user too before that

Firmware upgrade from 2.1(3a) to 2.1(3b).

Similar Messages

Maybe you are looking for