Firmware upgrade - Router van no longer be accessed

Thanks to an automatic firmware upgrade my E4200 can no longer be accessed. Cisco is aware of this but have no solution yet.
Great testing again Cisco before releasing.

LPD1964 wrote:
Thanks to an automatic firmware upgrade my E4200 can no longer be accessed. Cisco is aware of this but have no solution yet.
Great testing again Cisco before releasing.
Check if you are still getting the valid ip address from the router. Connect a pc to it and open command prompt and type-in ipconfig. If you are getting the 192.168.1.100 ip address on the local connection, try to ping the router (ping 192.168.1.1). If you are getting good replies then the router is good. If it will say request timed-out then reset the router back to defaults by pressing the reset button on it for 10 seconds.

Similar Messages

  • After time capsule 7.6 Firmware upgrade I can't set up Access Control / Timed Access using mac adresses.

    After time capsule 7.6 Firmware upgrade I can't set up Access Control / Timed Access using mac adresses.
    I have a Time Capsule and an Airport express and when I change access control parameters on whatever one of those
    two devices through Airport Utility its duplicating the same setup on the other device !
    What a mess !
    I had to choose "Not Enabled" in the Access Control stup window.
    Has anyone experienced same problem ?
    Jean.

    I did downgraded firmware to 7.5.2 ...
    and the Acess Control Setting from Airport Utility is back to normal behaviour.
    Jean.

  • Upgraded router VPN no longer working - LCP: timeout sending Config-Request

    I recently upgraded my small office router from a Linksys WRT54G to a Linksys WRT610N. I duplicated all of the port forwarding configs from my previous router, but everytime I try to connect to my server I get the following error:
    Could not negotiate a connection with the remote PPP server. Please verify your settings and try again.
    The ports I have forwarded to my server are the following:
    1701 UDP
    500 UDP
    1723 TCP
    4500 UDP
    While I am connecting I have been watching the log from Server Admin, and this is what I see:
    2008-07-11 06:09:35 PDT Incoming call... Address given to client = 192.168.1.63
    Fri Jul 11 06:09:35 2008 : Directory Services Authentication plugin initialized
    Fri Jul 11 06:09:35 2008 : Directory Services Authorization plugin initialized
    Fri Jul 11 06:09:35 2008 : PPTP incoming call in progress from '76.172.xxx.xxx'...
    Fri Jul 11 06:09:35 2008 : PPTP connection established.
    Fri Jul 11 06:09:35 2008 : using link 0
    Fri Jul 11 06:09:35 2008 : Using interface ppp0
    Fri Jul 11 06:09:35 2008 : Connect: ppp0 <--> socket[34:17]
    Fri Jul 11 06:09:35 2008 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0xef7517xx> <pcomp> <accomp>]
    Fri Jul 11 06:10:05 2008 : LCP: timeout sending Config-Requests
    Fri Jul 11 06:10:05 2008 : Connection terminated.
    Fri Jul 11 06:10:05 2008 : PPTP disconnecting...
    Fri Jul 11 06:10:05 2008 : PPTP disconnected
    2008-07-11 06:10:05 PDT --> Client with address = 192.168.1.63 has hungup
    I am still using 10.5.3. This may be very obvious to someone, but I'd appreciate any help.
    Thanks!
    Scott

    I am having sever issues with routers vs. VPN and I am hoping someone here can tell me how they got PPTP and L2TP working through the Apple Airport Extreme.
    Basically, I used to have a cheap, old, but perfectly working Linksys router. I opened ports for PPTP and L2TP pass through and VPN worked fine. I decided to upgrade the router because I wanted something with basic firewall functionality...
    I tried two new linksys products and gave up in disgust. Then I thought I had a brainwave and ordered the Apple Extreme Base Station. Well, this is almost as hopeless.
    I can get PPTP to connect now but the remote clients can't connect to the AFP server. L2TP simply won't work. I have 1701, 500, 1723 and 4500 ports forwarded to my server so I don't know what I am doing wrong.
    Also, I see on Apple's Server page that the Server will set up the Apple Extreme Base Station automatically??? How does this work?
    Lastly, Do I want to enable NAT port mapping protocol?
    Thank you,
    Gareth

  • Sky Router firmware upgraded - can no longer login with credentials

    I usually have no problems accessing my sky router (white Sky Hub with ADSL) via the page 192.168.0.1 however I tried to login the other day and was greeted with an updated looking summary screen - all very nice I thought, let's go and explore! However when I put in the usual details - username: admin, password: sky I get prompted to input my details again which is very odd. Now I know that I am the only one who accesses the router in this way as my flatmate has never logged in and probably never will so I can only assume the firmware upgrade has caused the password/username to change. I logged in the other week and the password is saved in my browser so I am sure I am not making any mistake here. I have tried in chrome and IE just in case but I have the same issue in both. Has the new firmware brought a new default password? I cannot find any reference to this anywhere on this site so it seems unlikely. I would rather not reset my router to default settings as I have devices with static IP addresses and port forwarding setup that will take me some time to reconfigure. I don't think there is any feature to backup the config unless you are actually logged in to the router but would love to be worng about this. I am guessing I will have to bite the bullet and reset to factory defaults but would welcome any help or suggestions if possible?

    After review the events of the morning.....
    I normally keep my routers in the basement where my eth jacks all hub.  High on a shelf, I got reasonable coverage on 2.4Ghz even on the second floor.  I went to this router for the Dual mode, but found the 5Ghz didn't make it sufficiently well to the second floor.  So it was moved to the first floor, on a counter.  That morning the router started acting up a bit, not bringing an iphone online.  It was looked at - and a couple of post cards that had been placed on top, removed.  Air flow was not blocked around the sides in any way - just a few pieces of card stock on top to interfere with convection off the top.  
    1.  There is no way to look at temperature - maybe the device doesn't even know its own temp.
    2.  There is no fan that I can discern.  Clearly, creating a device that is designed to sit on a flat surface in a home environment ought to take into consideration "normal impediments to air flow".   Temp controlled fans is simple, well proven tech.
    3.  This design is small, has TWO radios, sits horizonal (thus is going to have lousy convection) - seems to me an engineer ought to have given more thought to not only providing the user with easy to obtain data (temp), alternative methods (fan/vertical mounting) and/or self-protection (to hot, I'm shutting down rather than corrupt my database).
    Having spent millions on Cisco gear in my career, I would have hoped that Cisco+Linksys would have a little more Cisco and a little less Linksys.
    me

  • Firmware Upgrade for a WRT54G v8.1 Router

    I just resolved a connectivity problem by downloading and installing the binary
    file "FW_WRT54G_8.1.09.02_US_20071227.bin".
    After this upgrade, I was somewhat confused by the new displayed Firmware Version under Router Status in administration.  My new version is displayed as
    "8.01.09 build 01 Dec. 27,2007".  The date seems to agree with the downloaded binary file name.  The Release Notes for this latest firmware defines this download as "Last Firmware Version: 8.1.09 build2".  There is an associated Firmware Date of April 10th, 2008.  Do I have the correct file downloaded and installed for the WRT54G v8.1 Router or is there something else that I need to do to complete the firmware upgrade?
    There is one difference that I have noticed in my new configuration that is somewhat strange, as well.  I no longer have the ability to use "MAC Address Clone" in Setup.  It is grayed out. Please advise whether this is normal with this new Firmware.

    Yes, I am quite certain that the firmware was upgraded from version 8.01.08 build 02 Oct. 26, 2007.  The Router was reset after the upgrade and completely reconfigured.  The "MAC Clone" option remains grayed out after several attempts, but all other features are functional.  I have gained connectivity by this firmware upgrade to a Time Warner - Road Runner, Broadband System.  I may still want the MAC Clone feature in the future.
    Thank You!

  • After iPhoto upgrade i can no longer access the photos stored on my external hard drive, after iPhoto upgrade i can no longer access the photos stored on my external hard drive

    I was just about to order a photo book, using photos stored on an external hard drive. I organised the book and pressed 'buy'. IPhotos instructed me that I needed to upgrade and so I went on the ASpp store, bought the upgrade and installed as directed. I then used the iPhoto Library upgrader as directed.
    After the iPhoto upgrade I can no longer access the photos stored on my external hard drive. I am able to access the photos stored on my internal hard drive - the remainder (including the photo album) seem to have vanished into thin air.
    Any suggestions please?

    What format is the external drive?

  • Why can I no longer create/access playlists on my iPod since I upgraded to iTunes 10.5.2?

    Why can I no longer create/access playlists on my iPod since I upgraded to iTunes 10.5.2?

    I have the same situation. I believe I disconnected iCloud by going into preferences and also unclicking the box for Contacts. What am I missing?
    Larry

  • Firmware-upgrade failed router not accessible

    during firmware-upgrade the connection to E4200 got lost due to power-outage, now the E4200 router is not accessible, power-led flashes ...
    the factory-ip-address 192.168.1.1 responds on ping, but nothing else ...
    how to get a working environment back?

    Once reset the router. Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
    Once the light gets stabilize on the router perform the following steps:
    #  Open up the browser and on the address bar type 192.168.1.1, it will prompt for the username and password. Provide the username as 'admin' and password as 'admin' or 'password'. Then it will open up the Router setup page.
    # Then click on status and check the firmware version. If its not updated then upgrade the firmware once again.
    # Then after firmware upgrade  reset the router again as explained above.
    Then uninstall the existing Cisco connect software from the computer. After uninstallation then configure the router again using Cisco Connect CD as you did earlier.

  • Firmware Upgrade for Actiontec GT704WG Rev. B Router

    How do I find the firmware upgrade for the Actiontec GT704WG Rev. B Router?  Almost everytime I try to get onto the internet, I have to run the troubleshooter because there is no connection and the final diagnosis is that "The default gateway is unavailable."  Googled and found that it is due to the need for a firmware update for the router but cannot find one on the internet.  Help!!!

    Hi Funrunner
    You didn't say which version of the firmware you are currently running, however the latest firmware for that router is Version
    3.20.3.3.5.0.9.2.14
    Thank you,
    Peter
    Peter_VZ
    Verizon Support
    Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

  • I'm trying to update iPhoto 7.1.5 to current versions so I can get my photos onto iCloud to access from my iPad.  I can't seem to find an upgrade route that will work?  Any suggestions?

    I'm trying to update iPhoto 7.1.5 on my old iMac (running  10.9.5) to current versions so I can get my photos onto iCloud to access from my iPad.  I can't seem to find an upgrade route that will work?  Any suggestions?

    For Mavericks you need to upgrade to iPhoto 9.5.1.
    You cannot buy this version from the AppStore, since the current version is iPhoto 9.6, and that requires Yosemite. The easiest route for you would be to upgrade to Yosemite. Then you can simply buy the newest version of iPhoto from the App Store and can use iCloud Photo Library (iCloud Photo Library beta FAQ), once it has been release for the Mac as well early next year.
    If you want to stick with Mavericks, you'll have limited iCloud features, only the Photo Streams  (iCloud: iCloud Photo Sharing FAQ), but no iCloud Drive (iCloud Drive FAQ) and iCloud Photo Library.  And to upgrade iPhoto you need to buy an iPhoto '11 installer. It comes as part of iLife '11. You can try to buy a boxed version from Amazon or try to find it at eBay.  Once installed on Mavericks, download the iPhoto '11 updaters from the apple Support Downloads page.

  • Problem Upgrading Router Firmware on MI424WR-GEN3I

    Having trouble updating my router firmware.  Current version says:  40.21.18.  Status says: OK.  However, it says this below:
    " Internet Version:  Old Wireless Broadband Router version 40.21.10.3 found?
    Does this mean anything?  I'm wondering if the firmware is still not upgraded.  Any thoughts on this?  Did my firmware upgrade?  

    Your configuration indicates you do indeed have the latest firmware version installed.  The Internet version is what is available to restore to a previous version, should you ever have the need to do so.
    You can see how this would work (without actually activating it) by clicking on Advanced > Firmware Restore.  It will show you what your current version is and the previous version that's avialable to restore to.
    Once you've taken a look, click on Cancel  to avoid actually reverting to the older version.

  • Since I've upgraded to OS 10.7.5, I no longer have access to Apple Works. What can I do?

    I upgraded my MacBook Pro to 10.7.5 and no longer have access to Apple Works. How can I get it back?

    Find an alternative, or return to Snow Leopard, either directly or by running Mac OS X 10.6 Server inside a product such as VirtualBox, Parallels Desktop, or VMware Fusion.
    (127049)

  • How the heck do i get a firmware upgrade from my computer to the router?

    I went to this site here to try and make my router work. It is a WRT54GS wireless router, and I saw where i could download some firmware upgrade, so I clicked on it and saved it to my desktop. It is a .bin file. Now how do I get that file to the router?????
    The router was working until today and now it isn't sending out a wireless signal. However, it is still connecting my computer to the internet through its wire (modem to router, router to computer with cable). But when I open the Easylink software, it says that the internet connection is not working, even though the little green light is on for "wireless" on the front of the router.
    But anyway, how do I get this downloaded file onto the router??? There isn't any usb ports on the router to connect to it. There isn't anything in the Easylink software that gives me that option, or if there is they hid it pretty good. They really should explain how to do this, or do they expect everyone to have a degree in networking or computers or something? I need some help here 

    As sabretooth suggested,Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now,Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

  • WRT110 Firmware Upgrade Crashed IE8, Router Does Not Work

    Last night, at 2:30am EST I felt the need to upgrade the firmware on my router.  I downloaded the latest firmware for the WRT110 v1.0 and attempted to upgrade the firmware. Close to the end of the firmware upgrade process IE8 crashed and left my router in a state of limbo.
    I called Linksys support only for them to tell me that I have 3 options (all which included paying money to them) :
    Pay $40 to add 6 months of extended warranty to the router and support for it
    Pay $30 for a one time support call
    Buy a new router through them with waived shipping.
    This wasn't exactly what I wanted to hear at 3 am, so naturally I was quite irritated.  Of course, the supervisor asking me if I was sure I downloaded the correct firmware and telling me to go on the internet when it's obviously not working really did not help either.
    I tried the two reset options suggested by the forums here and the supervisor on the phone, pressing down the reset button for 30 seconds and pressing it down for a minute and unplugging for 30 seconds.  Neither worked, so the supervisor essentially told me the router needed to be replaced.
    Now, is there any actual way of getting the router back to a working state?

    There is always a way. Check this topic and follow the procedures.

  • Wireless B router woes after firmware upgrade

    I downloaded and installed the firmware upgrade for my wireless B ver.4 router and now it's not transmitting a wireless signal. Computers plugged into the wireless router get internet connection, but it doesn't seem that the the router is broadcasting wireless. I tried to go to my routers set-up by using the default router IP...but it won't connect...any thoughts?

    Since you have upgraded the firmware on your Router, You need to Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Maybe you are looking for

  • Need help in using a Secondary Index of a GL Table

    Hello ABAPers, Good morning/afternoon! I  was wondering if anyone could give me a hand on this issue. To give you a brief background, I need to retrieve Open and Cleared items in the last 24 hours, that is, from 11 am yesterday till 10:59:59 today. T

  • Boot camp and Windowa 7 (64 bit)

    Happy New Year to every one! My mac is a 2.66 GHz Quad-Core with 8 GB RAM, a nvidia GeForce GT 120 video card and 3 1 GB super ata HDs. Traditionally, one of the hard disks is dedicated to windows os and its applications. Since I got this mac I insta

  • Currency in PO not allowed

    Hello guys! Does anybody have any idea if there is any way not to allow a certain currency in a purchase order? Regards, Ileana

  • Screen freeze issue

    Hello, I am using XPERIA  Z1 ,which i got this April 2014. 1. The issue i face is the phone gets extremely warm on use of more than 1-2 applications.which is also the case on playing a game.I cannot hold at times due to the heat at the back of phone.

  • How can I confirm that fix for JDK bug will be in certain JDK update?

    Currently I am struggling with one of JDK bugs (link to issue). We would need it fixed in one of the JDK7 updates. According to Oracle's bug tracker this bug has been fixed in JDK 8 and backported to JDK7 for version: JDK 7u66 (link to issue). Last r