Firmware Upgrade was interrupted

Hi,
While I was ugrading the firmware of my phone n73 music edition, for some reason the upgrade was interrupted, I think the usb cable has a bad connection, a little touch it disconnects. The problem is that the phone does not turn on anymore. Is there any way to resolve this?
thanks

Hi napoleao
Unfortunately things do not look good and most probably a visit to a Nokia Care Point is now needed to re-install the phone software.
I don't know whether you have tried leaving battery out for at least 10 minutes before replacing, which sometimes seems to be necessary before proceeding with the following.
You might like to look at post from nando61 just input "N93 update fix" into "Search Discussions" at top right of screen. Although different phone to yours, it seems to be a question of whether NSU can be "tricked" into reading phone.
Happy to have helped forum in a small way with a Support Ratio = 37.0

Similar Messages

DMP 4300 Firmware Upgrade

During the firmware upgrade of a DMP 4300 from Ver. 5.0 to Ver. 5.0.2 there was a disconnection and the upload of firmware image was interrupted.
The DMP now does not boot and gives no display at all. It shows the red led indication but does not try to take an IP from DHCP.
Is there a way to resolve this issue?
Regards,
Chaitanya Datar

Chaitanya,
My apologies, but a power disruption or a transfer interruption during the firmware upgrade could cause a non-recoverable error on the DMP. The DMP will display the symptoms that you describe. The only resolution is to Open a Case with the Cisco TAC and RMA the DMP.
T.

Firmware upgrade stuck

My router says there is still a firmware upgrade in progress. I have flashed and reflashed (using UI and tftp util) multiple times, and this will not go away.
This is all on top of erratic behavior, dropping the connection, periods of no connectivity, periods of degraded performance, etc.
I've tried a factory reset, and holding the button in for 30 seconds. Nothing will get this perpetual firmware upgrade to go away.

Anytime a firmware upgrade is interrupted (for whatever reason) before it completes, there is a serious risk that your router will die. However, there is always some hope. Please try the following:
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 08-25-2007 03:43 AM

In the middle of undating to iTunes10.6.3 a window comes up saying an older version on bonjour cannot be removed. Then further into the download a window comes up that says the download was interrupted and can not finish and try at a later time.

I am attempting to upgrade to iTunes 10.6.3 and halfway through the download a window pops up that says "cannot remove an older version of Bonjour", then I click Ok on that and then further into the download and upgrade a window pops up that says cannot complete , itunes upgrade was interrupted, try at a later time.What do I do now?

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any Bonjour entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

WPSM54G Firmware Upgrade

I was trying to upgrade my WPSM54G from 1017 to 1019 but the upgrade button refused to engage despite the wired connection to the router. I experimented and found that the upgrade button would engage after I changed my wireless security so that wireless would not work. Once the wireless was disabled the upgrade went through without a hitch. I just kept it connected and restored the wireless security.
Solved!
Go to Solution.

I had a similar problem (but slightly different) but this solution worked for me. The "upgrade" button did engage/activate, but then the upgrade process would fail.
I disabled the wireless connection (by changing the SSID to something invalid), and then the firmware upgrade was able to complete successfully.

Winxp keeps rebooting - can't finish the firmware upgrade

The firmware upgrade was almost done. Itunes told me to not disconnect the phone until it re-appears in i-tunes. Then never happened - Windows said "USB device detected - digital still camera" and then my computer rebooted (after briefly showing me the blue screen). It keeps happening - I'm stuck in a loop Ideas?

Ok so after reading an older post that talks about incompatibilities with older logitech webcam drivers (and also references http://docs.info.apple.com/article.html?artnum=306048) I did the following:
1.I connected my ysb logitech webcam to my computer
2.I updated the webcam drivers
3.I disabled the device in Device Manager
4.I disconnected the webcam
5.I connecedt the iphone
Things worked this time.

Firmware upgrade for keyboard failed now keys won't work

Hi
Hope someone can help, I recently upgraded my sisters intel imac and during the aluminium (USB) keyboard firmware upgrade it failed and now computer doesn't recognise keyboard keys but usb hub on keyboard that mouse is plugged into works fine. Another keyboard works fine which was handy when trying to type in the passwords to try to re update.
I have tried the following
1) searched discussions found advice on resetting nvram, and in open firmware (which on further research doesn't seem possible on this imac?) did control, option P R on start up.
3) EFI firmware upgrade was successful
4) have used disk utility to repair permissions
5) Looked in system profiler and keyboard usb hub is recognised but no keyboard. When another keyboard attached it recognises this fine and is in the system profiler
6) checked all usb ports
Main question - can I fix or do I have to get a new keyboard or perhaps it would be less stress, time wasted etc to just buy a new keyboard???
thanks
G

Hi, if the K/B is under warranty Apple will replace it FOC..Call Apple Help or ->
call in at the local Apple Store or Apple Approved Service Agent.

How to reset the accessible RAM of my CE658A printer (LJ P1102w) back to 8 MB after firmware upgrade

My printer LaserJet P1102w has a RAM of 8 MB. After a firmware upgrade was made (of 3 time yet), it was shorter than of 6 MB, then of 4 MB, then of 2 MB. I see now (on the configuration setup web-page) the accessible memory is of 2 MB only! How to return accessible RAM back to 8 MB? The guarantee period has expired, I can't write a question to the HP support by e-mail. (All the firmware files were downloaded from the HP web pages. The upgrades were made under the Windows7_x64 OS.)

My printer LaserJet P1102w has a RAM of 8 MB. After a firmware upgrade was made (of 3 time yet), it was shorter than of 6 MB, then of 4 MB, then of 2 MB. I see now (on the configuration setup web-page) the accessible memory is of 2 MB only! How to return accessible RAM back to 8 MB? The guarantee period has expired, I can't write a question to the HP support by e-mail. (All the firmware files were downloaded from the HP web pages. The upgrades were made under the Windows7_x64 OS.)

ZVM Firmware Upgrade Probl

Hello,
I just received my Vision: M 60GB player and was wanting to upgrade the firmware. It is loaded with version .0 and I see that version .5 is posted. When I tried autoupdate firmware upgrade was not suggested. When I manually download the file and click on it, it says that the player is not connected. However, the player says docked and it is visible in My computer. In other words, all indications are that it is docked. I am running windows XP SP2 and this computer is less than a month old.
Thanks much for any advice you can give.

you can't upgrade from this firmware look at the info!
you can just switch to the beta n2go firmware or wait for the final version of it

Zen Sleek photo firmware upgrade

I found out that the Creative Zen Sleek had a firmware upgrade (PlaysForSure Firmware 2.0.03). The Creative Zen Sleek Photo hadn't... Can 2.0.03 be used on the Zen Sleek Photo and what is the effect of it's

The Zen Sleek Photo was a later model and may have included the fixes that the update for the Zen Sleek had. It could be the Zen Sleek's firmware upgrade was just to catch up.
I wouldn't use firmware for another player.

The installation was interrupted message after iTunes upgrade

I would appreciate help with my problem. I'd like to use iTunes but it doesn't work.
Description of the problem: I was happily using iTunes for more than a year. I received a notice that a new version was available and I upgraded. When the installation was complete I received the following message:
"The installation was interrupted before iTunes could be completely installed."
iTunes is not listed in the Programs menu and there are no files at c:\program files\itunes (itunes folder is not there).
After subsequent downloads and installs, I get the same error. When I do the iTunes standard install, QuickTime is
available and works well. I went back to the previous version, but it continued to give me the same error. I found very old versions of iTunes on the web and they too had the same problem.
During the install the iTunes icon briefly appears on my desktop and then disappears. The message box indicating that the installation was interrupted occurs right after that.
I've tried to describe the problem in quite a bit of detail below to help avoid suggested fixes that have been tried and failed.
1. I have followed the steps in the KB article. Please see the details of that work below.
http://docs.info.apple.com/article.html?artnum=93976
2. I have Administrator access. I have verified that I'm part of both the Adminstrators and SERVICE groups under Impersonate a client after authentication. This process is found in the following doc:
http://docs.info.apple.com/article.html?artnum=300361
3. Windows is fully updated through the Windows Update utility. See Windows version info below.
4. I can install any other application. I use this computer for work and I can install and uninstall any other application
I try. No other known errors or problems. I've installed other applications that use Microsoft Installer and InstallShield installers without problems.
5. I tried the Quicktime standalone install and I received the notice that "The installation was interrupted..." Quicktime is now not found on the machine and there is no Quicktime files in the Program Files. During the middle of the installation, I received the following error. Error during QuickTime Standalone (7.1.0.210) install:
Error 1905.Module c:\program files\QuickTime\qtuiPanelControl.dll failed to unregister. HRESULT -2147220472 Contact your support personnel.
When I attempt to install iTunes from the standard install, Quicktime installs properly and works. It only fails during the standalone install.
6. No strange characters in the folder. There is no itunes folder so it contains no folder. The download exe is on my desktop.
7. Temp Folder emptied and machine restarted (many times)
8. Uninstall older versions - They are not listed as installed so there is nothing to uninstall. The Windows Clean Up utility does not list them so I can't use that tool to remove them. It appears that iTunes is cleaning itself up when the installation fails so there are no files. There is no iTunes folder at c:\program files\.
9. iPodService alert is not there so I don't need to delete it.
10. Redownload software - It has been downloaded many times. Each time I'm careful to permanently delete the previous install exe so it is redownloaded.
11. AntiVirus software has been disabled. I'm using McAfee VS Enterprise 8.0.0. I have also checked the AV logs to see if it has blocked an install or other event around that time - there is nothing in the AV logs to show any blocked or prevented activity. No activity at all because the software is disabled.
12. Registry - A search of "itunes" in the Registry Editor finds a lot of references. Too many to list, but most are in keys that apply to file types.
13. I have downloaded and attempted to install the Windows Installer 3.0 package from the following URL:
http://www.microsoft.com/downloads/details.aspx?FamilyID=5FBC5470-B259-4733-A914 -A956122E08E8&displaylang=en&Hash=9PV3FS4
I'm told by a box during the install that the version I have installed is newer than the one on the website and there is no need to install it.
14. The version of iTunes that I'm trying to install right now is 6.0.4.2. I've had this problem for at least three months so I've been trying many versions before its release.
15. Other than the mentioned AV program, I don't have a third-party firewall, anti-spyware or monitoring program installed.
System:
IBM ThinkPad T42
Windows XP Pro
1 GB RAM
McAfee VirusScan Enterprise 8.0.0
Microsoft Windows XP Professional
Version: 5.1.2600
Service Pack: 2.0
Location: C:\WINDOWS
Hot Fix: KB913446
IBM T42 Windows XP Pro

It is a miracle - After about 9 months without itunes, the new release installed on my machine today and appears to be working.
7.0.0.70 is the verion I just installed.
Another note to add to this now resolved issue. I bought an AirPort Express and I was not able to install the Admin software on the CD. I received the same error as I received with iTunes and Quicktime. This leads me to believe that this problem is in the registry or some other installer issue that is specific to Apple installations. I will have to go home and try to re-install that software. Maybe the new iTunes version cleared up the problem.

How do I upgrade the iOs on my ipad1 to version5? I've tried through itunes many times, but I get a message that says that the download was interrupted and i should try again later. Can i download the iOS file to my PC and transfer it to the ipad?

How do I upgrade the iOs on my ipad1 to version5? I've tried through itunes many times, but I get a message that says that the download was interrupted and i should try again later. Can i download the iOS file to my PC and transfer it to the ipad? How should I do that?

Thank you!
Disabling firewall and AV did the trick!
Kudos.
Alex

Installation was interrupted message for a routine upgrade

Right after "Publishing product information":
"The iTunes for Windows installer has completed.
The installation was interrupted before iTunes could be completely installed.
The System has not been modified. To install this program at a later time, run the installation again.
Click Finish to exit the wizard. "
Describes the problem, but (1) this is a routine upgrade from the previous version (I've never had problems before), (2) I disabled all virus protection etc. (3) downloaded an other copy to make sure not corrupted
Dell Windows XP Pro

hmmmmmm.
okay, let's try enlisting some additional technical help.
let's try getting a installer log to someone who can interpret installer logs.
Start menu -> Run... In the text field of the dialog that comes up, type in "cmd" and hit return.
In the command prompt dialog that comes up, find the iTunes installer on your desktop and drag it to this window. Then on the same line type in a space and then the following:
/Verbose"c:\log.txt" /V"ENABLE_QTLOGGING=TRUE"
There is no space between the e in Verbose and the double quote ("). There is no space between the V"Enable...
Hit return.
The installer will create two log files:
C:\log.txt and C:\qt.log
Find those files and send them to this email address Put the URL to this discussion thread into the email, so that the person who gets it has some context. Let them know the version of itunes you’re trying to install, too … in general, give as much info as you can.

Hello my OS upgrade process was interrupted due to Internet failure, how may I re-try to upgrade it? I got a message that says I can´t, the serial number can be used only once!

Hello I bought a macbook pro on August this year and got a bonus to upgrade the OS from Lion to Mountain Lion for free. I started the donwload but it was interrupted due to internet failure so the upgrade process was aborted. When I tried to initiated the process again, I got a message that says I can not used the same serial number to download Maountain Lion. What can do in order to upgrade the OS using the "bonus" I received with the purchase?

I have the same problem, only Purchases in the App Store shows nothing. The download NEVER showed up in the App Store only in the Launchpad with a progress icon. The Icon said paused but when clicked, it just disappeared with no download.
How am I supposed to get my free upgrade now?

WRT54g v3 firmware update when the power was interrupted.

I have a WRT54G v3 modem. firmware update when the power was interrupted. now is access the router's web-based setup page not open and power led are flashing. DMZ led 5 seconds are flashing.
Help me please!

As the power light on the router is flashing,it means the firmware of the router is corrupted...Try this link and try to re-flash the firmware once again....Once done,reset the router for 30 seconds,power cycle the router and check..

Firmware Upgrade was interrupted

Similar Messages

Maybe you are looking for