Firmware upgrades from Nokia Updater

Guys !
Hello Again
I was unable to update latest firmware through Nokia updator
when I had 11.0.034 firmware. I consistantly got this message "Your software is up todate" though 20.0.058 software was released. Will Nokia tell us why this ia happening ?
If my post has helped you please click the white star on the right

23-Nov-2006 12:38 AM babdi wrote: Guys ! Hello Again I was unable to update latest firmware through Nokia updator when I had 11.0.034 firmware. I consistantly got this message "Your software is up todate" though 20.0.058 software was released. Will Nokia tell us why this ia happening ?
Your post is unclear. The main reason for this is that you do not mention which phone you're using. Anyow, things such as this can happen because of two (2) reasons:1. You have a branded phone, which contains software customised by your operator
2. You have a CV-variant, where CV stands for Country Version or Country Variant.
If the former is the case, you will need to wait until your operator releases the firmware for your specific model; Nokia's responsibility ends here.If the latter is the case, you will have to wait a bit longer, as not all CV's have been added to the database yet. To find out whether you have a CV or not, post the FULL output you have when you press *#0000# on this board (in this topic), and e-mail your product code to Nokia (you may choose to also post your product code on the board.
V3.0704.1.0.1
19-01-2007
RM-133 Nokia N73(57.01) Product Code:0539338

Similar Messages

Firmware upgrade for Nokia 6280

I would like to know do we have firmware upgrade for Nokia 6280 as my present one is 3.65 and would like to upgrade it to 5.92 and I am in India
Could you please help me out.

updating to new firmware depends on product code which represents your region of purchasing, language pack and if it's branded or not .... so NOKIA releases firmwares and release it for every product code depending on mentioned points
you can check for updates @ :
http://mea.nokia.com/support/download-software/device-software-update/can-i-update
To find what the latest available device software is, you’ll need your device’s product code. The code is printed on the white label beneath the battery (e.g. CODE: 0520001).
if your phone is branded with an operator, that means that you should go to the operator care center and ask them, not NOKIA
some updates delay in some countries variant product code, as it requires more effort to add language pack to it like "example. China Japan Korea" or it needs the country to approve it due to its policy
-you can show appreciation to my posts if it helped or useful by pressing the green Kudo star beside my post that hepled
-if my answer was the solution , so click accept as solution button
Started From Nokia 3310 , Now with Nokia N97 v.22.0.110 + N900 PR1.2

No firmware upgrade for Nokia 5800 in India

I havn't received any Message regarding the firmware upgrade fr Nokia 5800 XM phone. Even i have visted www.nokia.co.in, no info has been found yet.
Kindly advice

updating to new firmware depends on product code which represents your region of purchasing, language pack and if it's branded or not .... so NOKIA releases firmwares and release it for every product code depending on mentioned points
you can check for updates @ :
http://mea.nokia.com/support/download-software/device-software-update/can-i-update
To find what the latest available device software is, you’ll need your device’s product code. The code is printed on the white label beneath the battery (e.g. CODE: 0520001).
if your phone is branded with an operator, that means that you should go to the operator care center and ask them, not NOKIA
some updates delay in some countries variant product code, as it requires more effort to add language pack to it like "example. China Japan Korea" or it needs the country to approve it due to its policy
-you can show appreciation to my posts if it helped or useful by pressing the green Kudo star beside my post that hepled
-if my answer was the solution , so click accept as solution button
Started From Nokia 3310 , Now with Nokia N97 v.22.0.110 + N900 PR1.2

Firmware upgrade from 2.1(3a) to 2.1(3b).

I don't find any documentation on the web for firmware upgrade from 2.1(3a) to 2.1(3b)..
is it wise to follow this link http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/upgrading/from1.4/to2.1/b_UpgradingCiscoUCSFrom1.4To2.1.html
Any best practices ?

I would consult
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2.1/b_GUI_Firmware_Management_21.pdf
Cisco UCS B-Series GUI Firmware Management Guide, Release 2.1First Published:
Last Modified: July 12, 2013November 16, 2012

SPA112 firmware upgrade from 1.0.1 to 1.2.1 kills the SPA

I took a brand-new, unconfigured SPA112 out of the box, plugged it into DHCP-enabled network, noted it was running v1.0.1 firmware and attempted a firmware upgrade to 1.2.1 via the web management utility.
After reporting a successful upgrade there was no further response from the SPA112 to HTTP requests, neither was there any response to pings. ARP requests are responded to successfully. The IVR works (as well as the IVR ever works) until I selected to perform a factory reboot at which point the IVR stopped responding as well. Holding the reset button for 20sec does nothing useful. It's dead, Jim.
I've had this experience on another SPA112 as well under similar circumstances although there is nothing in the Release Notes for v1.2.1 to say that such an upgrade does not work.
My questions:
1)Is there any way of recovering these devices or do I need to send them back to Cisco?
2) How am I supposed to perform such a firmware upgrade?

Hi Matthew,
I tried upgrading the firmware upgrade from v1.0.1 to v 1.2.1 and I had the same problem. The device just stopped responding. I tried that in a lab and I figured out what exactly to do when you get in to a problem like that. So lets start off once again.
Snce SPA112 must get an IP first through a DHCP on WAN port. Connect the SPA 112 device according to the instructins told in this article till the step 3.
http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=2775
Once you access the web GUI of SPA112 follow the contents of the following article and upgrade the firmware
http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=2676
In your case I believe the window got stucked at the point when it says "The upgrade is successful" and then there was no further response to HTTP requests.
Restart the device and see if it works or not. If it does not then log in to the router web GUI and navigate to the ARP table and see what are the VLAN assigned to the IP address.
NOTE: Both the router and SPA should be in the same VLAN. This way only the device will respond to the HTTP requests. If they are in a different VLAN's, navigate to the VLAN and disable the LAN memberships. For example there are two VLAN ID 1 and 100. Disable the LAN ports for the ID 100 and only enable it for 1.
Navigate to the ARP table again and refresh it. Both the IP addresses should be in the same VLAN. If yes. Access the SPA112 with an IP address assigned to it again and navigate to Administration > Firmware Upgrade. You will see the firmware of the device has been upgraded.
(optional) Upgrade the firmware again. This time, it will go through and the device will restart.
Let me know if you still need any help.

HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

Hello,
I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
Thank you in advance for a reply - especially from HP.

Hi cyskim,
Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Firmware upgrade on Nokia 6610i

Hi,
I own a Nokia 6610i. I did *#0000# on the phone and I get this output:
v 4.10
08-10-04
RM-37
Now is there a way to check if that is the latest firmware? Seems that this phone is too old for the Nokia Software Updater
Some sites on the net report that v 4.50 is the latest firmware for this phone. Is that true?
If yes, can I go to a Nokia Care center to have my phone updated, or is the phone so old that they'll just laugh at me? Would they charge me, or are firmware upgrades free?
The phone actually works perfectly fine, but I like having newest versions of software That being said, is there a list of changes between the various versions of Nokia 6610i firmware?
Thanks a lot!
Rohan.

Thank you so much, korngear. Would you know if there is a list of changes somewhere? I don't think it's really worth paying for the upgrade if there only a few minor tweaks
Message Edited by rohandhruva on 29-Dec-2007 07:41 PM

How the heck do i get a firmware upgrade from my computer to the router?

I went to this site here to try and make my router work. It is a WRT54GS wireless router, and I saw where i could download some firmware upgrade, so I clicked on it and saved it to my desktop. It is a .bin file. Now how do I get that file to the router?????
The router was working until today and now it isn't sending out a wireless signal. However, it is still connecting my computer to the internet through its wire (modem to router, router to computer with cable). But when I open the Easylink software, it says that the internet connection is not working, even though the little green light is on for "wireless" on the front of the router.
But anyway, how do I get this downloaded file onto the router??? There isn't any usb ports on the router to connect to it. There isn't anything in the Easylink software that gives me that option, or if there is they hid it pretty good. They really should explain how to do this, or do they expect everyone to have a degree in networking or computers or something? I need some help here

As sabretooth suggested,Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now,Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

X3-02 RM-639 v7.51 fw not seen from Nokia update

Why does the 7.51 version firmware not appear from within the Nokia Suite as an available update? x3-02 RM-639 here currently at v5.65.

Updates vary by region and product code and operator handsets,which may be locked and in most cases you are left waiting,
Contact your provider if your handset is locked and ask them.After that you may just wait.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

BEFW11S4 v4 firmware upgrade from 1.45.3 to 1.52.02 failing

I've been having some problems with my router resetting so I decided to upgrade the firmware. I'm currently on version 1.45.3, Jul 1 2003 and I wanted to update to 1.52.02 4/07/2005. I downloaded befw11s4_v4_v1.52.02_000_FCC_code.bin from Linksys' site and selected it at http://192.168.1.1/Upgrade.htm. The progress bar will start to move and when it reaches about 75% I'm redirected to http://192.168.1.1/Upgrade.cgi which is a blank white screen . If I go back to http://192.168.1.1/ and check the firmware version I see 1.45.3 still. Does anyone have any idea what is going wrong?
Solved!
Go to Solution.

So I just went ahead and called the dreaded customer service.....turns out the filename just needs to be changed. There are 3 easy steps to fix this problem.
1. If its on your desktop the name should appear as BEFW11S4-v4_v1.52.02_fw,0 change it to befw11s4_v4_1.52.02_000_FCC_code.bin
2. Go to your upgrade firmware screen, click browse to get the file with the new name
3. Click upgrade and be happy that it worked!!

Changes after firmware upgrade in nokia 3250

hi i have nokia 3250 and want to are there any changes after upgrading firmware beacuse before i owned nokia 6270 and after upgrading firmware the music volume on my headset became very low and i dont want same wit my 3250

yeah, the N80 has a history of being buggy. Even with the latest firmware. Its a shame, because it was a damn good phone. Anyhow
You can download Yahoo!Go from:
http://uk.mobile.yahoo.com/go
Not sure about the others. (My operator, Three, offers Yahoo Messenger and Yahoo Go to its customers, but they "are incompatible with the N80" if you can believe that.)
Anyhow..
Currently using E71, looking at options

ASA firmware upgrade from console - tftp error

Have an asa 5510, trying to upgrade the firmware via console.
I have a tftp program installed on my PC but get an error running the command, any idea what I'm doing wrong?
asa# copy tftp flash
Address or name of remote host [142.xx.xx.xx]? ------------> IP of my PC
Source filename [asa912-k8.bin]?
Destination filename [asa912-k8.bin]?
Accessing tftp://142.xx.xx.xx/asa912-k8.bin...
%Error opening tftp://142.xx.xx.xx/asa912-k8.bin (No such device)

Hi,
You really cant upload files through the Console connection. Its not a network connection.
Your PC might have an IP address configured but that would be configured in its network interface card which has nothing to do with the console cable connection.
So you will have to configure one of the ASAs network interfaces with IP address and other basic settings. Then you need to configure the PCs network interface cards settings to match the IP address/subnet configured on the ASA. Then you will have an connection between the ASA and the PC and should be able to load the software to ASA.
For example
interface Management0/0
nameif management
security-level 100
ip address 10.10.10.1 255.255.255.0
no shutdown
and the configure the PC with IP address 10.10.10.100 and mask 255.255.255.0 for example and then load the software from the PCs IP address of 10.10.10.100.
- Jouni

Iomega StorCenter NHDD2 Firmware Upgrade from v1.27?

I hope you can help me;
I have an old Iomega NAS device that has performed flawlessly for as long as I can remember (2006 I believe?) but having attached a USB HDD to the rear it is only allowing read only access. Would a firmware update solve this?
If so, how would I go about it as the device does not show up in the LenovoEMC Storage Manager (v1.4.4.14439).
Thanks in advance,
Mac

Hello macaulay576
Is this a HMNHD? or HMNHD CE (2)? Could I have you provide the first two digits of the unit's serial number so I can confirm the correct device type?
If it is one of the HMNHD variants you should be able to modify the connected external drive's access permissions via the web interface.
If this is a device older than the HMNHD devices, you should still check the web interface for access permission options for the connected drive (it usually will show up as a share even on the older units) Firmware may help, but depending on the device an update may not be available any longer.
LenovoEMC Storage manager should be able to detect most legacy StorCenter devices, if it doesn't the unit may be too old to be detected correctly. you should then use your router or a network scan to detect the unit's ip address. the " arp -a " command will work in Windows and OSX to scan your local network and list the detected devices and their ip and mac/physical addresses.
You may also want to check here to see if there is any further suggestions on the forums.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

NAC firmware upgrade from 4.1.3 to 4.7 or 4.8, anyone?

I currently have 1 CAS 3310 Failover Bundle for Wireless user, and 1 CAM Lite Failover Bundle for management.
ACAS, CAM and Clean Access Agents are running 4.1.3. We are considering an upgrade in particular because some end-users machine are soon to be Windows 7. Our authenticaion for users is provided by AD SSO.
I would like to know your experience when doing such a major jump (4.1.3 to 4.8.1). Looking for gotchas and known issues. Also what the incremetal upgrade path look like.
I was thinking we can go 4.1.3 -> 4.6.1-> 4.8.1. Any other way or recommendation. CIsco is highly recommending we go to 4.8.1 if all possioblem.
I am also aware that we need to create new root certificates.
Appreciate input.
Thanks,
Rosa

Hi,
Yes, that is the correct upgrade path: 4.1.3 -> 4.6.1 -> 4.8.1.
I would recomend you to go through the Release notes for 4.6.1 and 4.8.1 for all the known gotchas and detailed upgrade process.
Gotchas/changes/upgrade process for 4.6.1: http://www.cisco.com/en/US/docs/security/nac/appliance/release_notes/461/461rn.html#wp65900.
Gotchas/changes/upgrade process for 4.8.1:http://www.cisco.com/en/US/docs/security/nac/appliance/release_notes/48/481rn.html#wp65900.
Regarding the certificates, you should not use the self signed certs due to security reasons, and they should only be used for lab purposes.
This means that it still works with the self signed, but you need to import the CAS cert into the CAM trusted certification authorities and vice-versa, so that the CAM trusts the CAS cert and vice-versa.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

WLC firmware upgradation from 6.0.196.0 to 7.0.98.0

Hi,
I have not come across to upgrade the IOS of WLC at any time .
Right now , I have WLC 6.0.196.0 and it is working fine but still if in case I need to upgrade to 7.0.98.0 or whichever is latest , What is the procedure ?
How to go about it ?
kindly suggest me for the same.

Hi Vinod,
Sorry for the late reply.. this forum thingy is messed up.. suddenly this throws me off!! hav to re-login.. strange!! ok lemme get back..
Main image = The image helps you in getting the GUI and helps you in configuring through the CLI..
Boot Loader image = Is almost equal to ROMMON version on switches!! ok lemme explain u in WLC world.. When you reboot ur WLC, while rebooting if u hit "Escape" then you can see something like the Intial WLC config wizard.. or while doing the PASSWORD recovery we select options 1 to 5.. this is called as Boot loader version..
The complex explanation is.. A boot loader, also called a boot manager, is a small program that places the Operating System (OS) of a computer into Memory. When a computer is powered-up or restarted, the basic functions performs some initial tests.
lemme know if this answered your question and mark it as answered if so!!
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Firmware upgrades from Nokia Updater

Similar Messages

Maybe you are looking for