Firmware Version 3.1 or higher

I have an iPOD 10GB (older model, M8976LL)...I recently purchased a Belkin TuneBase FM so I can play my iPOD in my car...The minimum Firmware version required is 3.1...my iPOD has a 2.3 Firmware version....A few questions...1) is an firmware upgrade available for my older iPOD...2) if so, how do I find it to download it...I've been all over the Apple site and can't fine any reference to upgraded firmware...PLS HELP ...and THANKS

BTW, all iPod software versions beginning with 3.xx are only compatible with the iPod with click wheel. If your software version begins with 2.xx you have an iPod with dock connector, which might be incompatible with the accessory which you just purchased... make sure you hang onto that receipt!

Similar Messages

  • Firmware version is too high. How uninstall? Correct version where?

    Help! That Firmware thing is driving me nuts. Wish apple would organize the latest upgrades by OS. It’s a maze.
    My iMac DV (blue front slot loading) is OS 9.0.4 (I will upgrade but not right now, too long to explain).
    I had bought a LaCie HD some years ago & made partition with OS 9.0.4, 9.1 to 9.2, it fell, bought another and installed it.
    After much time I found out that to know my version of Firmware I have to look for boot ROM, my system profiler says it’s $0004.19f1 that means probably v 4.19.
    If it’s v 4.1.9 it is too high it needs OS 9.1 and probably happened with I had OS 9.1 on my external HD. My LaCie CD Writer became a nightmare and I don’t dare to use it anymore, maybe it was because of the firmware ….or it might be that Apple CD/DVD Driver can’t exist at the same time as Toast extensions, it’s unclear to me.
    Can’t find the latest firmware version for OS 9.0.4 that will work, or how I can take it off before I install another one. I know v2.4 will work on OS 9.0.4.
    Got: Firewire v2.3.3 - usb v 1.4.2 - CarbonLib v 1.6 - Apple CD/DVD Driver v 1.3.5 player is v2.1
    Help!
    1. What’s the latest Firmware for OS 9.0.4?
    2. Do I have Firmware v 4.1.9?
    3. How do I uninstall Firmware v 4.1.9?
    4. CAN Apple CD/DVD Driver exist at the same time as Toast extensions?
    Thanks very much
    Nicky

    I think that you misunderstood Kappy's point about Mac OS X version.
    What the information about OS X version is telling you is that those are the minimum requirements for the installer which places the firmware update permanently in the ROM on the logic board to run. However, once the firmware has been installed you are free to continue to update your version of Mac OS X for as long as Apple releases them.
    I have an iMac G3 DV+ which has ROM version 4.1.9f1 and is running Mac OS X 10.4.8.
    However, the firmware is backwards compatible as well. You obviously installed the firmware when you were running OS 9.1, but at some time regressed your OS to 9.0.4.
    I think the issues that you are experiencing are related to other issues on your Mac. The folks in the iMac G3 forum should be able to help you sort that out.

  • Firmware version explanation + sleep problem

    My 10 days old iMac baby has problems to sleep. It goes to sleep but after 5-6 minutes it's awaken again. I tried everything I found relevant to this problem on this discussion board but no help at all. Mac baby was born with 10.4.8 and now it's at 10.4.10 - combo update, everything else is working perfectly well except this sleeping problem. I
    After all, I went on Apple download in order to check if there are some EFI Firmware updates and now I'm more than confused with numbers.'
    On Apple's site it's clearly written that the most recent firmware version for my iMac is "IM51.0090.B03 (20-inch late 2006)" http://www.apple.com/support/downloads/imacefifirmwareupdate11.html but my System Profiler shows higher number count: "IM51.0090.B08".
    From System Profiler:
    Hardware Overview:
    Model Name: iMac
    Model Identifier: iMac5,1
    Processor Name: Intel Core 2 Duo
    Processor Speed: 2.16 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache (per processor): 4 MB
    Memory: 2 GB
    Bus Speed: 667 MHz
    Boot ROM Version: IM51.0090.B08
    SMC Version: 1.9f4
    Does anybody has any idea about this?
    Tnx,
    Denis
    iMac 20'' (Late 2006)   Mac OS X (10.4.10)   2 Gb Crucial DDR2 RAM @ 667 MHZ, WD My Book Premium Edition 250 GB

    Others have also found what appears to be a discrepancy in the firmware that System Profiler reports installed on their Mac versus the version reported in Apple Knowledge Base documents. The definitive document for me is Mac OS X: Firmware Updates for Intel-based Macs. This doc confirms the information that you report, so the logical explanation to me is that, although the doc was last updated by Apple on 1 MAY 2007, there has been an update to installed firmware in Macs shipping since the doc was last updated.
    But the firmware shouldn't have anything to do with whether your Mac sleeps or not. Sleep is one of the things regulated by the System Management Controller. This can be reset.
    But there are many other things that can interrupt the Mac auto-sleeping; external FW/USB peripheral devices, wifi, Bluetooth, etc. Have you added any such devices recently.

  • Is the new Firmware version of 5800 supports VoIP?

    I want just want to ask for those whoe already updated their 5800 to version 40 firmware if their phone already supports VoIP. I've read on some forums that Nokia 5800 doesn't support VoIP. Is the new update already have like the VoIP support of N97?

    mj_monserrat wrote:
    I want just want to ask for those whoe already updated their 5800 to version 40 firmware if their phone already supports VoIP. I've read on some forums that Nokia 5800 doesn't support VoIP. Is the new update already have like the VoIP support of N97?
    No, it's voip capabilities are exactly the same as previous firmware versions so it still does not support true native voip like the N97 does.
    The 5800 is highly unlikely to ever receive this feature.  As before you will need to use a program such as fring or nimbuzz for voip on the 5800.

  • Problem with restore.I have a 2 gen running firmware version 4.2.1

    Hello there !
    Hopefully some smart persons here will be able to help me. First it has been awhile since i used my itune store because i didnt needed to and did a format of my computer after the last time i used it..so i had to upload my library etc and start from scratch. I downloaded a couple new games,everything was working fine..then when it came the time to sync and put these games on my ipod touch 2 gen the installation failed. I retried again and it keeps failing again and again so i choose to do a restore on it and expecting the problems would be solved. Problem wasnt not solved at all and it said an error (6) occured and i have the image on my ipod of the white cord trying to connect to itune store.
    Restore doesnt work at all and it seems like my ipod is totally useless as i cant use it anymore. I did the diagnostic..it said no ipod were found. I also did the check up thing for the technician so ill paste it here maybe it will give some clues..
    I have this error now as well... No iPod, iPhone, or iPad found. It also said secure link to itune store failed..not sure if these are all related to the same problems or all different at all..im clueless and need a generous soul to help me out.
    Thank you tons for the help !
    @Edit : Even with my other 2gen ipod i cant install these new games,it keeps failing as well..but at leasnt i havent done Restore on it yet and i fear to do it for reason you guys can guess.
    Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
    System manufacturer System Product Name
    iTunes 10.3.1.55
    QuickTime 7.6.9
    FairPlay 1.11.17
    Apple Application Support 1.5.2
    iPod Updater Library 10.0d2
    CD Driver 2.2.0.1
    CD Driver DLL 2.1.1.1
    Apple Mobile Device 3.4.1.2
    Apple Mobile Device Driver 1.57.0.0
    Bonjour 2.0.5.0 (214.3)
    Gracenote SDK 1.8.2.457
    Gracenote MusicID 1.8.2.89
    Gracenote Submit 1.8.2.123
    Gracenote DSP 1.8.2.34
    iTunes Serial Number 00AAB2F80F513CD0
    Current user is an administrator.
    The current local date and time is 2011-07-17 18:45:37.
    iTunes is not running in safe mode.
    WebKit accelerated compositing is enabled.
    HDCP is supported.
    Core Media is supported.
    Video Display Information
    NVIDIA, NVIDIA GeForce 9500 GT
    **** External Plug-ins Information ****
    No external plug-ins installed.
    **** Network Connectivity Tests ****
    Network Adapter Information
    Adapter Name:     {B00FE55A-1662-4EE9-B880-6B076869B9F8}
    Description:     Contrôleur Atheros L2 Fast Ethernet 10/100Base-T
    IP Address:     192.168.2.10
    Subnet Mask:     255.255.255.0
    Default Gateway:     192.168.2.1
    DHCP Enabled:     Yes
    DHCP Server:     192.168.2.1
    Lease Obtained:     Sun Jul 17 17:51:16 2011
    Lease Expires:     Wed Jul 20 17:51:16 2011
    DNS Servers:     192.168.2.1
    Active Connection:     Connexion réseau
    Connected:     Yes
    Online:          Yes
    Using Modem:     No
    Using LAN:     Yes
    Using Proxy:     No
    SSL 3.0 Support:     Enabled
    TLS 1.0 Support:     Enabled
    Firewall Information
    Windows Firewall is off.
    ZoneAlarm Firewall is installed.
    Connection attempt to Apple web site was successful.
    Connection attempt to browsing iTunes Store was successful.
    Connection attempt to purchasing from iTunes Store was unsuccessful.
    The network connection timed out.
    Connection attempt to iPhone activation server was successful.
    Connection attempt to firmware update server was successful.
    Connection attempt to Gracenote server was successful.
    Last successful iTunes Store access was 2011-07-17 18:43:19.
    **** Device Connectivity Tests ****
    iPodService 10.3.1.55 (x64) is currently running.
    iTunesHelper 10.3.1.55 is currently running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    Universal Serial Bus Controllers:
    Contrôleur d'hôte ouvert PCI vers USB NEC.  Device is working properly.
    Contrôleur hôte PCI vers USB standard étendu.  Device is working properly.
    Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27C8.  Device is working properly.
    Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27C9.  Device is working properly.
    Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CA.  Device is working properly.
    Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CB.  Device is working properly.
    Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CC.  Device is working properly.
    No FireWire (IEEE 1394) Host Controller found.
    Most Recent Devices Not Currently Connected:
    iPod touch (2nd generation) running firmware version 4.2.1
    Serial Number:     9E01226F201
    **** Device Sync Tests ****
    No iPod, iPhone, or iPad found.

    thats just rubbish ! i bought it secondhand for my daughter to use for music and apps, but its not compatible with anything, any suggestions other then throwing it away?

  • How do you upload firmware to Airport extreme with the following message: This version of AirPort Utility requires this AirPort Extreme use firmware version 7.3.1 or later. Use AirPort Utility 5.6 to update this base station. I'm using airport utility 6.0

    The airport extreme at my parent's house has not had its firmware update in some time and it keeps dropping the internet connection and needing to be reset.
    I went to update firmware and opened up airport utilities (I'm running airport 6.0 on Mountain Lion, 10.7.4).  Everytime I open the airport utility I get the following message: "
    This version of AirPort Utility requires this AirPort Extreme use firmware version 7.3.1 or later. Use AirPort Utility 5.6 to update this base station. AirPort Utility 5.6 is available at AirPort Service and Support.
    I've followed the link and tried to update firmwares but none are available and the print says that airport utility will look to see if firmware are available and load them as necessary when prompted by user.
    One link said the only way to solve this problem is open up Airport Utility 5.6. I tried to do this, but 5.6 is not supported on Mountain Lion and couldn't be opened up.
    I'm getting the exact same message on my other computer, a Mac Air.
    So basically, can't download new firmware and am stuck with a ****** airport extreme that needs to keep being reset, a factory reset, in order to use the internet, but then continues to give me the same message.
    Thanks!

    See this article for instructions on how to install AirPort Utility 5.6 for Lion on Mountain Lion:
    http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html

  • Will firmware version 4.1.7 automatically update to 4.1.9?

    I recently upgraded to OS 10.3 from OS 10.0 on my Imac 700MHz G3. The installation documentation said that I would be prompted to upgrade the firmware if I needed to. I was not prompted so I went ahead and did the OS 10.3 installation. The firmware remained version 4.1.7f4 after the install.
    Not too long ago I went through the same procedure on my Imac 400MHz DV. The only difference is that I started the upgraded process from OS 9.I, then to 9.2.2 using the updates (ending at the latest version of 9), then to 10.0, and then to 10.3. And finally updating with 10.3.9 combo to OS 10.3.9. During that whole process I never new about firmware and never checked to see what version I had before starting this process. After all of the above installations were finished I ended up with firmware version 4.1.9f1.
    My concern is with the 700MHz G3 IMac. I'd like to update to 10.3.9 using the combo update but I'm concerned about the firmware. Will firmware 4.1.7f4 be updated automatically to 4.1.9f1 after the combo OS 10.3.9 is installed? Or should I erase the disk again and start over by first installing firmware update 4.1.9? Actually if that were the case I wouldn't be able to update my firmware since I don't have the correct bootable version of OS 9 on disk that is required for that computer. However my previous experience with the installations on the 400MHz DV suggests to me that that the firmware will automatically be updated. But I would like confirmation from the experts. I'd hate to spend all that time downloading and installing all of the latest updates (Combo 10.3.9, etc.) only to find that the firmware version is incorrect.
    Thanks!
    Al

    Al,
    I don't understand your anger. In your first message
    you posted that you installed OS 9 and updated it to
    9.2.2. So why don't you do that again on the 700 MHz
    iMac?
    I find it very amusing that somehow you see anger in my post. That is realy very funny! The reason I didn't just simply install OS 9 on the 700MHz Imac is stated in my original post. I would need a special (the original disk that came with this computer) bootable OS 9.1 disk to install 9.1 on this particular computer. However if there are retail 9.2 or greater disks available then that would work to. I own a retail version of 9.1 that I used for the 400MHz Imac. That wont work on the 700MHz Imac. So now I have to buy a another OS 9 disk. Thanks for your input. Al

  • Firmware Version 4 1 106 1982 of IomegaEZ MAL PERFORMANC​E and improve performanc​e

    Firmware Version 4.1.106.31982 of IomegaEZ MAL PERFORMANCE !!! and improve performance?
    I upgraded to version 4.1.106.31982 the IomegaEZ and enter SETUP MAL has PERFORMANCE WEB, it is very slow unlike the previous firmware version; as performance improves VERSION of this? You can return to the previous version without losing data?
    Thank You
    Ruben Arno
    ESPAÑOL
    Version de Firmware 4.1.106.31982 de  IomegaEZ de MAL RENDIMIENTO !!! como mejorar el rendimiento ?
    He actualizado a la version 4.1.106.31982 el IomegaEZ y al ingresar al SETUP WEB tiene MAL RENDIMIENTO,  es muy lento a diferencia de la version de firmware anterior; como se mejora el rendimiento de esta VERSION ? se puede volver a la version anterior sin perder datos ?
    Gracias
    Ruben Arno

    Hello pcyservice
    There is NOT a way to downgrade/roll-back/revert to a previous firmware without wiping all data.  This is specifically mentioned on the firmware update page:
    " CAUTION!
    This update is not data destructive, however, ALWAYS back up your data before performing any firmware update!
    Once you have updated the firmware, you will NOT be able to revert to an older firmware version."
    I recommend you disable any unnecessary features/protocols such as Media Server and Active Folders, then reboot the unit.
    If you are still experiencing performance issues, please contact LenovoEMC support to troubleshoot further.
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • HP OfficeJet Pro 8600 Plus Firmware version not current on the HP Downloads Page

    My HP OfficeJet Pro 8600 Plus came with Firmware version CKP5CN1334ER which the printer update says is up-to-date. The HP downloads page shows CLP1CN1322CR as the current version. Can you tell me what the differences are in version 1334 from the one (1322) on the web page?
    It would be nice to have the latest version posted for download to prevent confusion.

    Same question here.

  • How do you determine the firmware version for a laptop docking station?

    How do you determine the firmware version of a HP docking station?
    Laptop Model: HP 2740p
    OS: 64bit Windows 7
    Expansion Base: 2740 Ultra Slim Expansion Base WA995AA#ABA
    Thank you for any assistance.
    Alvin

    atenpo wrote:
    How do you determine the firmware version of a HP docking station?
    Laptop Model: HP 2740p
    OS: 64bit Windows 7
    Expansion Base: 2740 Ultra Slim Expansion Base WA995AA#ABA
    Thank you for any assistance.
    Alvin
    WA995AA#ABA shows to be a hard drive, not a docking station

  • Did the most recent update and now my TB Display turns off randomly on both my air and mini. I running  TB Firmware Version:     23.6

    did the most recent update and now my TB Display turns off randomly on both my air and mini. I running  TB Firmware Version:
    23.6

    When did you get this firmware version?  My TBD is at 22.2 and the TBD bus is at 23.4.  I thought I had the latest firmware.

  • An eligible Logic Pro version was not found in the Applications folder. This update requires Logic Pro version 9.0 or higher.

    Get this error when trying to install Logic patch 9.1.4 to my machine.
    An eligible Logic Pro version was not found in the Applications folder. This update requires Logic Pro version 9.0 or higher.

    Thx, but i had already read that and tried it: did not work.
    Got it fixed now by reinstalling Logic Studio 9 from DVD.
    That indeed creates the Logic Pro folder in Applications - something I had tried earlier by simply moving my existing Logic folder. This means the Logic 9.1.5 update does not simply check a folder name: there must be another entry/registry entry it checks. Reinstalling Logic Studio from scratch solved it for me.
    After reinstalling thought Lion forgot my Focusrite Saffire 40, so no DAW. Solved that by reading a forum entry on beta drivers.
    So I am happy, music creation wise.
    Left for me is to solve the X Mail application saying it does not run under Lion!
    Model Name:          Mac mini
      Model Identifier:          Macmini3,1
      Processor Name:          Intel Core 2 Duo
      Processor Speed:          2.26 GHz
      Number of Processors:          1
      Total Number of Cores:          2
      L2 Cache:          3 MB
      Memory:          2 GB
      Bus Speed:          1.07 GHz

  • How do I determine current firmware version for WRT54G

    I've been poking around the site a bit, and note that there are mandatory upgrades to various firmware versions. I'd like to upgrade if necessary, but have no idea how to determine what firmware version I have right now.Message Edited by shelmart on 12-17-200605:36 AM

    What is the excact hardware version # of your router? U can find that underneath the router itself, there's a sticker there & its just right below the Linksys Logo. If its version 5 or 6, u can go to this website: www.linksys.com/connect . Download  & save Easylink Firmware Tool & then before u run that file after saving, disable first all your internet security like firewalls & anti- virus coz it will block the connection of this software from running properly. That EFL will automatically upgrade the firmware of your router.

  • Need a Script to Audit Firmware version of HP components​.

    Hi Team,
    I am new to this portal, I am not sure if i have selected the correct board for this issue. If not please redirect thie thread to the correct team or guide me the link to the HP Blade system portal.
    My issue:
    We have 285 HP Servers, Where almost 275 are HP Proliant BL460 G7 & G8 Blades and the rest are HP DL380P and DL380 Standalone servers.
    We recently did a HP SPP Update on all these machines and now for a reason we want to Audit if the component updates were correctly done by our engineers or not.
    How ever for HP OS Components i have a script to Scan the registry and pull the Product version and match it to see if it has the Latest version or not.
    But how do i do an Audit for the ILO'S of these machines and the Onboard Administrators and the HP Virtual connect if the firmware versions are correct or not ?
    Is there any script or any Method to achieve this ? 
    We also have HP SIM tool as well, Can we do it form that? If yes then how ? Can any one please help in this ?

    Frederik, After some tweaking and testing i was able to get it working, I haven't tested it via GPO as a startup script but standalone it is doing what i was after. I cant thank you enough for helping me on this as i had lost hope after days worth of intense
    searching
    Change that i had to apply ( space in a network path
    was causing a "path not found error", Had to rename the "Office365 update" and update the path in Customconfig.xml  or any other location that was pointing to "office365 update" )
     set DeployServer=\\contoso\c2r\Office365 update\
    REM Set ConfigFile to the configuration file to be used for
    deployment (required)
    set ConfigFile=\\contoso\c2r\Office365 update\Customconfig.xml
    REM Set LogLocation to a central directory to collect script
    log files (install log files are set in XML file).
    set LogLocation=C:\AppData\Local\Temp

  • Nokia N80 new firmware version 4.0707.0.7

    It's so bad firmware version!
    I have lots of problems with new firmware version 4.0707.0.7 that I haven't with past version 4.0623.0.42 !
    I can't understand what's going on with NOKIA Software Updater!
    >I can't enter to my "Gallery\Images & Video" from "Camera Mode"
    >My OS speed decrease
    >Captured photos don't show in "Images & Video" until I restart my N80
    >For each new files you add, you need to restart your N80 until your N80 find them in memory!!!
    Why past version haven't these PROBLEMS and new version have them!!!
    Does anybody know how can I return to my past firmware version (mean 4.0623.0.42) ? Is it possible?Message Edited by zoologist1 on 03-May-200712:28 PM

    04-May-200710:53 PM
    djassa1 wrote:
    Basically it means that BB5 phones like N-Series including N80 and E-series cannot be downgraded to a previous version once they have been upgraded. Trying that with third party tools, because it's not possible through NSU, will brick (dead) your phone, period.
    That's why I said you'd have to take the phone to a service center.

Maybe you are looking for

  • Asset Close and Open period

    hi how close asset period and want to make entry in 2010 the how open period 2010 for Asset Accounting entry in which Transaction code . thanks Kisanp Moderator: Please, read basic SAP material

  • Permissions issues when trying to import CD

    When I try to import a CD to iTunes, it gives me the following error message : "Error occurred while converting the file "SONG NAME". You do not have enough access privileges for this operation." - iTunes could not save to your Music Folder and folde

  • Replace characters in StringBuffer

    I am importing some XML data using Java code and importing the data into an Oracle database, but there is at least one wierd character in the data. The character looks like an apostrophe (what most people call a single-quote), but it's not the apostr

  • Mustek scanexpress a3 usb 2400 pro

    Hi, So at work I was trying to hook up this scanner I have near my station, a mustek scanexpress a3 usb 2400 pro, but I can't detect it. I downloaded the latest drivers off the Mustek website and I tried using Vuescan, Image capture and Photoshop to

  • My screen on my Mac book doesn't work anymore and just stays black.

    The screen on my Mac book pro does not work anymore. The computer still come on but nothing will come on the screen.