First time working with 802.11n, not working properly?

Hello,
This is the first time I use 802.11n in my network there is only one AP1141 but the clients don't connect at 802.11n rates, instead they connect at data rates as low as 11 Mbps. At the begining they connect at 144 Mbps but immidiatly it decreases to 11 or 12.
Many of our wireless clients in the company are Intel(R) WiFi Link 5100 AGN.
Any comments?
AIR-AP1141N-A-K9
AIR-WLC2106-K9
6.0.182.0
Let me know if more info needed?
Thanks

Hi George,
So you suggest to keep only WPA2/AES?
Regarding the coverage area keep in mind this is a really small 4 floor building with an AP floor floor, I installed only one AP1141 in my floor and kept the AP1131 in the other 3 floors, I might reduce the power to half since I don't need them working at full power unless I need coverage in the stairs in order to enforce roaming to IPPhones. Also, I don't want to bond channels on 2.4 because I read that as a recomendation in a Cisco's document (anyways I did not find how to do it in 2.4, wuld be a nice tip if you tell me how just in case) so 144 Mbps would be great as long as it works properly. I did not experienced these rate hoping until I enabled this AP1141.
And yes most of the clients that reported issues are Intel (engineering team, haven't checked the rest yet).
Regards!

Similar Messages

PC laptop card to work with 802.11n?

I'm thinking of getting the new Extreme for my wife's Late 2006 Macbook Pro, but her sister is often on the same network with her PC laptop, an Acer Aspire 5100-5022 on which the current card is only g/b. Anyone know @ how much for an upgraded card for that, and any specific recommendations?
Thanks

I will give it a try for a second time with the installation method they suggest at Amazon. It works ok with Airport but it has a lot of issues with speed. I was with a technician at Linksys and after going through all my settings, they asked me to try with another computer. I am in the process to buy a new laptop and try it there to see where the problem lies. (he he he)
I will post an update when I try the new installation.
By the way the older adapters 802.11N can reach the 300 Mbps if the router is set in the 5Gzh/40Mhz radio band.
Many thanks for your comment and the link.

802.11n not working.....6hrs of frustration!!!!!!!!!!!

I've spent basically all day yesterday on the phone with Apple tech support and even took my unit to an Apple store with no conclusion yet. Here's the deal...
I have a PC laptop (Windows XP SP2, non wireless)....D-Link cable modem running to my 802.11n base station.....then my base station running to my PC laptop. I get service fine on the laptop. In the same room (10 feet away) is my Powermac G5 (OSX 10.4.8 and all current software updates) with a airport card. I'm in an appt building so I know my airport card is working because I'm picking up other networks from other tenents. I have a green light on the base station but I can't connect for the life of me on my G5. I even connected the modem/base station to my mac and it recognizes it through the airport utility and I was able to name it and give it a password but even directly connected to my G5 my wireless card isn't picking up the signal..........PLEASE HELP!!!!!! Forgot to add....I took the base station to the apple store and it worked there! Do you think it's the D-Link modem?

The Airport Extreme defaults to a 10.1.1.x address.
Most PC-Based Wireless hubs distribute 192.168.1.x
addresses. Set your Airport Extreme to redistribute
192.168.1.x addresses, and you will be able to
connect.
MacBook T2700
2gHz, 12GB, 160G Windows XP Pro Dual
Boot with latest OSX
ummm...no..that should not matter at all

Macbook CD2 802.11n not working

I have a macbook (cd2) and it wont connect as a 802.11n to my linksys router that has 802.11n. i can get the Atheros ar5008 to connect as N while in my mac partition, but i cant get it to connect while i am in XP. i tried reinstalling the latest driver, and deleting all the "preferred networks," but it's not working

Boot Camp Beta 1.2: Windows XP (SP2) unable to connect to 802.11n wireless router or AirPort Extreme (802.11n) Base Station
Relevant previous discussion.
iFelix

Will older macs ever work with 802.11n

Just wondering if the requirements for 11n is just a matter of buying a new network card or does the hardware also have to support it as well. I ask only because I have a G4 & G5 on my existing airport network. Have a MacBook Pro also on network. I would like all of them to be at the same speed if possible.
multiple macs Mac OS X (10.4.8)

retouch4food, Welcome to the discussion area!
As you undoubtedly know from reading the "Help & Terms of Use" for this area, we are all Mac users like yourself. Therefore we have no special knowledge of future Apple plans or products. Also the discussion of future plans and products is forbidden in this discussion area.
But... based on past history... it is very doubtful that you will see any type of 802.11n upgrade for existing non-802.11n Macs. 802.11n depends on multiple antennas to perform it's magic and it would be very difficult to change built-in antennas in the existing Macs.
With all that said... if you want to give your non-802.11n capable Mac 802.11n access, the best solution will probably be an Ethernet 802.11n adapter.

NB520, Replaced display, only work with AC power, not work with battery

Hi
I just replaced a broken display on my 7 months old Toshiba NB520 and now it only works with AC power.
The battery icon shows 52% but not charging.
When I plug out the AC power, it turns off.
Help

Please help guys. I dont know what more to do...

Js working with FF but not working with IE

Dear All,
I have created a text field P5_NO1 and in the
Post Element Text
<span style="color:#0000ff;font: normal 1.2em "Lucida Sans Unicode",sans- serif;font-size:12px;"> <select id="unit" onchange="TankUnit();" >
<option> -S-</option>
<option> ml</option>
<option> kg </option>
</select> Units
</span>
the js TankUnit() works fine in FF not in IE
I have an sample in apex.oracle.com
http://apex.oracle.com/pls/otn/f?p=4000:4150:4089089633206316::NO:::
can anyone help me to solve the problem?
bye
Srikavi

Hi Peter and John,
FF is so... tolerant to accept the value of the option as the same as it is displayed in the select list.
where IE is so... prudence, that we have to explictly tell it
ie Post Element Text in IE should be like this
<select id="unit" onchange="TankUnit();" >
<option> -S-</option>
<option value="ml"> ml</option>
<option value="kg"> kg </option>
</select> Units
bye
Srikavi

Airport Express 802.11n - not working at all!

I have had some trouble with my Airport express. Nothing works. I have tried to hard reset and factory default reset but nothing happens. It's only blinking yellow, and if i put a ethernet cable into it it turns green, but it still not showing in either airport (wireless) or at the airport utility. I have checked with both my MacBook Pro and my Mac Pro.
I also have a Airport extreme and i tried to expand the network wirelessly when i had the express up and running, but when it restarted it self it didn't show up nowhere.
Can someone help me out here?

After a factory default reset, the AirPort Express is broadcasting a wireless network with a name like Apple Network xxxxxx.
If you are tying to configure the Express using wireless, you need to make sure that your Mac is logged on to this network first, before you open AirPort Utility.
It's also possible to connect an Ethernet cable from your Mac to the AirPort Express and then open AirPort Utility. Once the Express has been configured an updated, you can remove the Ethernet cable.

Power PC G5... Will it work with 802.11n?

I have a 20" iMac, 2.1 GHz Power PC G5, running OS 10.4.11.
Can I connect with wifi on the "n" side of the extreme base station with this computer? I currently have the 802.11g side with the older extreme base station. But I'm thinking about getting the new extreme base station and would like my imac to connect on the "n" side if possible via wifi.
Any info is greatly appreciated! Thanks
TS

Can I connect with wifi on the "n" side of the extreme base station with this computer?
Yes. Use a component such as this one.
(46533)

FlexUnit is working with FlashBuilder and not working with Build file

Hi
I have few flexunit test cases . When I am running those testcases from Flashbuilder FlexUnit plugin I am able to run all the testcases and when I run Build file to run those testcases , build file is launching my testrunner swf file and it is throwing follwoing runtime error in flash player
VerifyError: Error #1014: Class flash.events::NativeWindowBoundsEvent could not be found.
at flash.display::MovieClip/nextFrame()
at mx.managers::SystemManager/deferredNextFrame()
at mx.managers::SystemManager/preloader_preloaderDocFrameReadyHandler()
at flash.events::EventDispatcher/dispatchEventFunction()
at flash.events::EventDispatcher/dispatchEvent()
at mx.preloaders::Preloader/timerHandler()
at flash.utils::Timer/_timerDispatch()
at flash.utils::Timer/tick()
here is the Build Console log
[taskdef] Could not load definitions from resource flexTasks.tasks. It could not be found.
test:
[mxmlc] C:\Users\user\Documents\workspace\project\bin-debug\projectTestRunner.swf (1626331 bytes)
[flexunit] Validating task attributes ...
[flexunit] Generating default values ...
[flexunit] Using the following settings for the test run:
[flexunit] FLEX_HOME: [C:\Program Files\Adobe\Adobe Flash Builder for Force.com\sdks\4.5.1.21328]
[flexunit] haltonfailure: [false]
[flexunit] headless: [false]
[flexunit] display: [99]
[flexunit] localTrusted: [true]
[flexunit] player: [flash]
[flexunit] command: [C:\Program Files\Adobe\Adobe Flash Builder for Force.com\sdks\4.5.1.21328\runtimes\player\10.2\win\FlashPlayerDebugger.exe]
[flexunit] port: [1024]
[flexunit] swf: [C:\Users\user\Documents\workspace\project\bin-debug\projectTestRunner.swf]
[flexunit] timeout: [60000ms]
[flexunit] toDir: [C:\Users\user\Documents\workspace\project\report]
[flexunit] Setting up server process ...
[flexunit] Starting server ...
[flexunit] Opening server socket on port [1024].
[flexunit] Waiting for client connection ...
[flexunit] Entry [C:\Users\user\Documents\workspace\project\bin-debug] already available in local trust file at [C:\Users\user\AppData\Roaming\Macromedia\Flash Player\#Security\FlashPlayerTrust\flexUnit.cfg].
[flexunit] Executing 'C:\Program Files\Adobe\Adobe Flash Builder for Force.com\sdks\4.5.1.21328\runtimes\player\10.2\win\FlashPlayerDebugger.exe' with arguments:
[flexunit] 'C:\Users\user\Documents\workspace\project\bin-debug\projectTestRunner.swf'
[flexunit] The ' characters around the executable and arguments are
[flexunit] not part of the command.
[flexunit]
[flexunit] Stopping server ...
[flexunit] End of test data reached, sending acknowledgement to player ...
[flexunit] Closing client connection ...
[flexunit] Closing server on port [1024] ...
BUILD FAILED
C:\Users\user\Documents\workspace\project\build\build.xml:33: The following error occurred while executing this line:
C:\Users\user\Documents\workspace\project\build\build.xml:175: java.util.concurrent.ExecutionException: Socket timeout waiting for flexunit report
Many thanks for In advance for your help ..

We had a similar problem in my project. Took a lot of research and trial and error, but we finally narrowed it down to the resource.properties file. Turns out that if the file gets too big it causes this problem. Extending the timeout doesn't help. You have to break your resource.properties into more granular files to reduce the file size. This seems to fix the problem. We have had it happen several times since then and we know how to fix it, so we get it fixed pretty quickly.
Not sure if this will fix your problem, but it fixed ours.

How can I get my AE to work in 802.11n mode with my dlink router?

Hi all,
I have a dlink 655 wireless n router that I use for my network and a recent AE with 802.11n capability that I use to connect iTunes to my home stereo.
I have a mix of computers at home and only my imac has 802.11n capability. I work alone in the day so to speed things up, I change the wireless setting on my dlink router to 802.11n only mode. Normally, it is in a mixed mode of 802.11g/n for the other non n computers on the network.
My imac connects fine when in 802.11n only mode but the AE looses connection. As it is 802.11n capable, I was wondering why this happens?
I tried checking Airport Utility for a 802.11n only mode or something similar, but didn't find anything. Will the AE only work in 802.11n mode when on the 5ghz frequency? if so, that would explain why it doesn't connect with the dlink 2.4ghz router in n mode.
Any ideas?? Thanks!

Hi. Thanks for the reply. It turns out that the router was not going into n mode because of the security I set on it. I finally figured this out and the AE did connect in n mode after all.
Well at least it's working now but I feel a little bad for posting when it was my fault!!
Cheers!

Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q with a real time mode but it is not working but when i run it with uploading it into the PXI it save in to the file

Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q and DAQ NI PXI-6229 with a real time mode but it is not working but when i run it without uploading it into the PXI it save in to the file please find attached my vi
Attachments:
PWMs.vi ‏130 KB

other problem is that the channel DAQmx only works at real time mode not on stand alone vi using Labview 8.2 and Real time 8.2

I just fix my macbook air because it was kernel panic. They changed the hard drive. I could not back up with Time Machine, because it did not work and I had over Adobe creative suite 5 design premium student. But I finished my studies last year and I'd li

I just fix my macbook air because it was kernel panic. They changed the hard drive. I could not back up with Time Machine, because it did not work and I had over Adobe creative suite 5 design premium student. But I finished my studies last year and I'd like to know how to get the serial number for me to reinstall Adobe creative suite 5 design premium when I am no longer study because I would still like the used? It is not fair if I do anymore because I really need.

You can download Creative Suite 5 here:
Other downloads
To deal with the issue of the serial number and using it again, you'll have to use Web Chat. Here's a link:
Adobe ID, sign in, and account help
See the bottom of the page for a link

HT201412 I was trying to update my iphone but it gives the following error(We're sorry, we are unable to continue with your activation at this time) Now my phone is not work working can anyone help?

I was trying to update operating system of my iphone but it gives the following error(We're sorry, we are unable to continue with your activation at this time) Now my phone is not work working can anyone help?

Is your iphone hacked/jailbroken?

Don't know if this went through the first time. Cannon printer would not print black. bought a new Epson-800. Same problem. Can it be something in my Mac causing the problem. It's only the black that is not working.

Don't know if this went through the first time. Cannon printer would not print black. bought a new Epson-800. Same problem. Can it be something in my Mac causing the problem. It's only the black that is not working.

Bill ...
Believe it or not, might be a font issue > Computer won't print black text in...: Apple Support Communities

First time working with 802.11n, not working properly?

Similar Messages

Maybe you are looking for