Fixed ip address NAS not being found

I have a mysterious network problem. I have a buffalo linkstation as NAS which is connected on to a switch (US robotics) which is connected to the network via an airport extreme which is set up as a remote base station on a WDS link from an airport express which is connected to the cable modem. The idea is that the airport express gets the internet access and acts as main base station on the wds link, assigning ip addresses to all the network elements. The problem is that the linkstation must have a fixed ip address so that i can access its setup screen via my browser. I therefore assigned it the address 10.0.1.25 (for no specific reason). The main airport express is at 10.0.1.1 and it assigned 10.0.1.233 to the airport extreme. What is strange is that none of the other network devices can see the linkstation except the mac that set it up. This is a problem because i want that linkstation to act as a music store for my sonos system but it cannot find it on the network even tough it's plugged into the same switch. Can anyone suggest a trouble shooting solution? I guess the problem comes from the fact that i have allocated a manual ip address to the linkstation and that therefore the airport express does not have it in its routing table to communicate it to the network elements but if i set the linkstation to get an ip address, i can't reach it via the web client anymore because i won't know it's ip address. i have been working on this for hours and would be infinitely grateful for any help. thanks.
p

The Express has a set range of IP addresses that it distributes via DHCP. You can change the range in the Airport Admin Utility. The best solution is to limit the range somewhat and assign your fixed IP addresses outside that range. I don't know that it'll fix the problem, though.

Similar Messages

  • The FIX for FireWire Devices not being found.

    If you have FireWire devices connected to your iMac that are no longer being recognized, this post is for you.
    1. Power off your iMac
    2. Unplug all USB and Firewire cables from the iMac.
    3. Unplug the iMac from the main power.
    4. Wait 4 minutes
    5. Reconnect and power on.
    6. Devices will be found as you'd normally expect.
    Somehow, four minutes without any kind of power resets the Firewire interface so that it will work again.

    1. Power off your iMac
    2. Unplug all USB and Firewire cables from the iMac.
    3. Unplug the iMac from the main power.
    4. Wait 4 minutes
    5. Reconnect and power on.
    6. Devices will be found as you'd normally expect.
    On step five, you say 'reconnect and power on'. Does this mean I should turn on my external device and connect before I turn the iMac on?
    As for my ports being blown, I don't think that's the problem for me. My iPod easily mounts on firewire. And this device mounts on my other machines that use 10.3 panther.
    Sorry if it sounds like I'm trying to hyjack this topic, it sounds like you've got a good method and I want to utilize it properly!
    Thanks,
    ben

  • Images and .properties(bunldes) files are not being found from my JSPs

    Hi,
    I have created .ear file by using ANT Application. And deployed into Oracle9iAS(OC4J). Here problem is that images and .properties(internationalization bundles)files are not found from JSPs.
    Here is my directory structure.
    public_html--->locale -->BusinessEntity -->businessentity_en_US.properties
    --->enterprise -->images -->knowldege.jpg
    --->BusinessEntity-->BEAdd.jsp
    in my jsp bundle(.properties)file is accessed like this:-
    <i18n:bundle baseName="/locale/-->BusinessEntity/businessentity" id="businessentity" locale="<%= locale %>" />
    in my jsp images accessed like this:-
    src="/enterprise/images/knowldege.jpg".
    In my working environment, without creating .ear file, images and .properties files are being found my JSPs. But if i create .ear file and after deploy, images and .properties files are not being found my JSPs.
    please let me know where i might did wrong
    thanks in advance
    srinivas

    Hi i am again. Here is my configuration files(server.xml and default-web-site.xml)
    server.xml :-
    <?xml version="1.0"?>
    <!DOCTYPE application-server PUBLIC "-//Evermind//DTD Orion Application-server//EN" "http://xmlns.oracle.com/ias/dtds/application-server.dtd">
    <application-server application-directory="../applications"
    deployment-directory="../application-deployments"
    >
         <library path="../tools.jar" />
         <rmi-config path="./rmi.xml" />
         <jms-config path="./jms.xml" />
         <log>
              <file path="../log/server.log" />
         </log>
         <transaction-config timeout="30000" />
         <global-application name="default" path="application.xml" />
         <application name="nalluri" path="../applications/trainiumear.ear" auto-start="true" />
         <global-web-app-config path="global-web-application.xml" />
         <web-site path="./default-web-site.xml" />
         <cluster id="-1640090707" />
    </application-server>
    default-web-site.xml:-
    <?xml version="1.0"?>
    <!DOCTYPE web-site PUBLIC "Orion Web-site" "http://xmlns.oracle.com/ias/dtds/web-site.dtd">
    <web-site port="8888" display-name="Default Oracle9iAS Containers for J2EE Web Site">
         <default-web-app application="nalluri" name="Commonwar" />
         <access-log path="../log/default-web-access.log" />
    </web-site>
    thanks in advance
    wating for reply
    srinivas

  • Sim Card not being found on Passport

    I have a new Passport which I like.
    It is locked to Vodafone and I have a Vodafone Sim
    First 10 days it was fine then the sim card was not being "found"
    I tried two new sims and no luck.
    It seems the device may be faulty.
    I bought it from a private user on Ebay for which it was an unwanted upgrade.
    How do I get it repared?

    Ok. Since it was purchased from an non-official retailer on eBay, I don't know...
    you might try the BlackBerry per incident support channel.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • WD Mybook not being found

    Hi,
    Anybody have any ideas why the WD mybook using firewire or usb is not being found by the iMac?? It had been working fine until a week ago and it will work in a windows enviroment. Any ideas woud be great Thanks.
    Imac 20"   Mac OS X (10.4.8)  

    The format maybe in NTFS (windows), as far as I know macs cant read that, see if Mac OS X can find it by going Macintosh HD > Utilities > Disk Utility or (Spotlight > Disk Utility) and see if you can see it there with your iMac hard disk, if it is unplug it and backup everything on your PC and wipe the external drive, then plug back in your iMac and then go to Macintosh HD > Utilities > Disk Utility or (Spotlight > Disk Utility) and format the external HD in FAT or FAT32 when done unplug and take back to windows pc and copy data back to drive. Try that and post your results

  • [svn:osmf:] 14982: Fixing some event parameters not being forwarded.

    Revision: 14982
    Revision: 14982
    Author:   [email protected]
    Date:     2010-03-24 02:15:50 -0700 (Wed, 24 Mar 2010)
    Log Message:
    Fixing some event parameters not being forwarded.
    Modified Paths:
        osmf/trunk/apps/samples/framework/OSMFPlayer/src/DebuggerElementProxy.as

    Hi,
    Thanks for posting in Microsoft TechNet forums.
    I will try to involve someone familiar with this topic to further look at this issue. There might be some time delay. Appreciate your patience.
    Thank you for your understanding and support.
    Kate Li
    TechNet Community Support

  • File shares in EMC Isilon NAS not being accessible .........in windows file server

    Hi
    We have an odd issue in windows 2003 server where the users are not being able to access the shares in EMC Isilon NAS drives.
    Found that the KB 3002567 installed on last Tuesday March 10 2015, caused the issue and related to Data that resides on EMC Isilon clusters is unavailable to SMB/SMB2/SMB3 clients.
    Finally resorted to uninstall the particular patch from the Domain controllers of 2003 & 2008 and the shares are being accessible.
    Is there any alternative to this process of uninstallation of the patch KB 3002567 ......since this patch has to be uninstalled in pending DC's?
    Any help is greatly appreciated
    Thanks & Regards S.Swaminathan Live & let others live!!!

    In my own environment, I found the following registry value to be helpful:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\LanmanWorkstation\Parameters:RequireSecureNegotiate=2
    (DWORD)
    http://blogs.msdn.com/b/openspecification/archive/2012/06/28/smb3-secure-dialect-negotiation.aspx
    Greetings/Grüße,
    Martin
    Mal ein
    gutes Buch über GPOs lesen?
    Good or bad GPOs? - my blog…
    And if IT bothers me -
    coke bottle design refreshment (-:

  • Contact pictures in Address Book not being displayed

    Hi,
    I am syncing my address book, calendar with Google. My "source" usually is the Mac address book. After having activated the "Mac <=> Google" sync, everything worked fine in the begining. But the last six weeks I seem to have a problem with the contact pictures:
    I have created contact pictures for nearly 95% of my contacts. These pictures were copied to the address book either from iPhoto or from the web. Via Google sync, the contacts are transfered to my iPod touch, my iPhone and my Nokia Lumia 800.
    Suddenly the contact pictures started to disappear from my Mac address book, but were still visible in my Google address book and my mobile devices.
    When I started to add the pictures to my address again I realized that most pictures are still there, they were simply not being displayed in my Mac address book. By switching to "edit mode" and opening the picture field I could see the pictures again. After clicking "OK" the pictures is visible again.
    I double checked all pictures, added the few missing ones and created an "address book archive". Yesterday all pictures gone again. I imported the archive, all pictures back again. This morning, the pictures are gone again. This whole thing doesn't seem to affect Google or the mobile devices.
    Any idea what the problem with the address book is?
    PS: Before you suggest to switch to iCloud. I need to sync my address book and calendar with all my mobile devices. If I would use iCloud, I would not be able to sync with my Nokia Lumia 800 (Windows Phone). And from comments in the forum, there seem to be similar problems with iCloud concerning address book information.
    Thanks for your ideas.

    I found this article online:
    http://reviews.cnet.com/8301-13727_7-20004209-263.html
    Export an Address Book Archive of all your contacts, then import it right back in. Worked like a charm.

  • Office HP P1505n printer connected to network not being found

    Hi,
    I'm trying to fix a problem we have had since experiencing a power cut last week. Our main support guy is on holiday and i am pretty new to our network.
    After we lost power i had to manually start all of our servers and services and i thought everything was working until a user tried to use one of our printers.
    The error message for one of the printers was 'Error - Offline' and the other says 'Unable to connect'. Both messages being displayed from the print options in microsoft word. The 2 printers are a HP LaserJet p1505n and a HP Colour LaserJet CM 2320.
    We have a small network with a domain controller and DHCP on one server and our printer installations on another (running Windows Server 2008 R2 64-bit. The printers are connected to the network via ethernet cable. I remember someone mentioning restarting a network switch which is next the printers which i have done.
    I printed a config page from one of the printers and made sure that the displayed IP address was correct in DHCP. It was correct for the address lease and reservation for the printer. When i try and ping the printer from a computer i get 'Destination host is unreachable'.
    It must be something to do with settings not being right after the power cut but i'm not sure where next to look.
    Any advise would be very welcomed.
    Thanks!

    Hello jamesrussellcj, and welcome to the HP Forums.
    I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at HP Commercial LaserJet Forums.
    I hope this helps!
    Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
    Jamieson
    I work on behalf of HP
    "Remember, I'm pulling for you, we're all in this together!" - Red Green.

  • Classes in web-inf/lib not being found.

    I'm having problems with a servlet app in which jar files placed in the web-inf/lib of the application are not found at runtime.
    If I put them in J2ee\home\lib they are found OK.
    This application has previously deployed and worked correctly, then I added another servlet and redeployed, and classes that were previously found OK stopped being found.
    On checking the server all the directories look correct.
    What could be causing this and how can I make my web applications deploy reliably?
    OC4J version is 9.0.3.0.0.
    Thanks

    Guys,
    Have you tried with the production version of OC4J 9.0.2 ? It should work. Please download the production version of OC4J 9.0.2 and give a try.
    regards
    Debu Panda
    Oracle

  • How to solve Error SPSite - The Web application at address could not be found

    Hello,
    I am trying to find out the internal name of a custom SharePoint list columns, for this I have used following code snippet in my
    console application but getting below error. The site I am accessing is a public SharePoint web site. This code is working
    well with my local host site and i am able to get the internal names of any list columns but don't understand why this is failing with
    public SharePoint site
    For avoiding this issue I have done following steps:
    1.Rebuild the application
    2.changed the  platform target as "Any CPU"
    3.Visual studio and this public site is working in my admin account, but still I am getting the error!
    I use visual studio 2010 and SharePoint 2010
    please note the error I am getting
    Error : The Web application at https://public.sp.a5-group.com/ could not be found. Verify that you have typed the URL correctly.
    If the URL should be serving existing content, the system administrator may need to add a new request URL mapping to the intended application
    Code Snippet
    static void Main(string[] args)
    using (SPSite Site = new SPSite("https://public.sp.a5-group.com/"))
    using (SPWeb web = Site.RootWeb)
    SPList splst = web.Lists["ListCard"];
    foreach (var field in splst.Fields)
    bool isHidden = splst.Fields[field.ToString()].Hidden;
    if (!isHidden)
    string internalName = splst.Fields[field.ToString()].InternalName; //This will give you the internal column name.
    Console.WriteLine(internalName);
    Console.ReadLine();

    I thin you need to have sharepoint installed on same computer and URL should be working on this computer.
    If this URL WEB APP is in your IISsite try to create disableloopbackcheck registry which should be help
    When you use the fully qualified domain name (FQDN) or a custom host header to browse a local Web site that is hosted on a computer that is running Microsoft Internet Information Services (IIS) 5.1 or a later version, you may receive an error
    message 
    http://support.microsoft.com/kb/896861

  • HT1386 ipod touch not being found by itunes

    just downloaded the larest version of i Tunes and now my iPod touch wont sync and id not being recognised by iTunes!!!!"!!!!!!

    iOS: Device not recognized in iTunes for Mac OS X
    Or
    See
    iOS: Device not recognized in iTunes for Windows
    - I would start with
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or              
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
    - Then do the other actions of:
    iOS: Device not recognized in iTunes for Windows
    paying special attention to item #5
    - New cable and different USB port
    - Run this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    Also see:
    iPod not recognised by windows iTunes
    Troubleshooting issues with iTunes for Windows updates
    - Try on another computer to help determine if computer or iPod problem

  • Can not restore due to folder not being found

    I just want to wash my ipod harddrive and just start over due to a couple of problems I have had.
    Whenever I connect to itunes, it does not recognize that it is a nano, but does say it is an ipod, and that it is corrupted, so I should restore.
    I click restore and the error that comes up is
    " can not restore because the correct folder can not be found "
    any ideas what that is about.
    already done all the troubleshooting steps to no avail.
    not a newb on the computer so its frustrating me.

    You might want to try deleting the "iPod Photo Cache" folder on your computer.
    See the instructions here:
    Photo Sync creates iPod photo cache
    After that, restart your computer, and try restoring your iPod again.
    Any difference after trying that?
    -Kylene

  • TS3299 I do believe that Apply should send a patch to fix the issue of not being able to burn a cd

    Why hasn't Apple created a patch to rectify this problem of not being able to burn cd's ?  I have tried to go through the lengthy solution - holding my breath, not wishing to make things worse I tried but................. it didn't cure the problem.  A patch please Apple.

    Hello Country Linda,
    Thank you for your question. It sounds like you are unable to burn an audio cd in iTunes. Here is a general list of troubleshooting steps to check if you are having issues with iTunes burning your music to a disc.
    iTunes 11 for Windows: If you have trouble burning a disc
    http://support.apple.com/kb/PH12349
    In order to assist you better, would you mind providing more details on why you are not able to burn a disc? Is there an error message of any kind? What happens when you try?
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • Has anyone else experienced problems with the disc burner/driver software not being found?

    I am trying to burn music onto a disc and it is telling me that the disc burner/driver software has not been found. Has anyone else experienced this with their MacBook Pro?

    SuperDrives wear out - it seems that yours might be on the verge of a mechanical failure. I'd just replace it, buying a new drive from Other World Computing and installing it yourself (because Apple would charge a small fortune).
    Clinton

Maybe you are looking for