Flash drive doesn't fit in ss USB port

Hello,
i have hp pavilion 15-n208TX laptop.
It has total 3 USB ports
my pendrive and other USB cables don't fit in one port. I applied the pressure but no result.
all ports are same than what is the problem ?
is the port has any hardware problem ?

Hello @h4c127 ,
Welcome to the HP Forums!
I understand you're having troubles with one of the ports on your Pavilion notebook.
I took a look at the specs for your product and I can see that you actually only have 2 USB ports on the notebook. The third port you are using is most likely the Ethernet (RJ-45) or HDMI port. If you look carefully they should be labeled to help you confirm this.
(Source - HP Pavilion 15-n208tx Notebook PC Product Specifications)
Hopefully this provides some insight!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Similar Messages

External USB2 drive doesn't work on left USB port

Hi,
I have an 2,5" external usb hard drive which works on my right usb port, but not on my left one, when i try the disk on the left port, afterwards the usb port is dead untill restart, even my mighty mouse does'nt work on it. My logic board and board with audio and left usb port are already replaced, without result, also the cable beween logic board and daughter board...
The disk works on a colleage's macbook pro on both ports...
what to do?

Try resetting the PRAM:
http://docs.info.apple.com/article.html?artnum=2238
Make sure also that no USB devices are connected when you put the machine to sleep (close the lid, or start energy saver).
A restart will clear a hung USB port usually.

Cable doesn't fit into back USB ports

My front USB port isn't working...everytime I plug a cable into it I get a message that reads "Power Surge on Hub Port" and it won't connect. My ports in the back are functioning, but I cannot connect my iPOd into them because the cord doesn't fit. Is there something I can buy (like a mini extension cord) that will connect them?
Please help I am so frustrated. thanks!

thanks so much for your help...
I'm using a Dell Computer (it has Optiplex GX270 written on it) with Windows XP. If you need more info just tell me where to find it.
Even when I plug in a USB cable (one that isn't connected to a device), the message still appears. The iPod connector does fit in the front, but not the back ones. I know the back ones work because I plugged a camera into one in the back and it worked, (it didn't in the front).
I would just use the back ports for my iPod too but the cable is a little different and won't work. I think there is excessive plastic on the connector?

I cannot get my computer to recognize the flash drives that I plug into the usb ports

I tried to locate a file from a memory stick and I could not get my usb port to recognize that I had inserted a memory stick in the usb ports.

No. I use VMFusion Version 2. I have not had this issue before. I have tried multiple memory sticks and they are not being recognized.

Flash drive only mounts when connected through USB hub

I have a PNY 32gb USB 2.0 flash drive, when trying to connect the drive directly to my Mid 2012 MBP (specs attached) the drive never mounts, doesn't list in diskutil as an unmounted drive either, however when I plug the drive into a Micro Innovations USB Hub (old ~ 2002) the drive mounts (albeit slowly).
On my iMac (Mid 2010 I7) the drive works perfectly in the machine or through Apple USB Keyboard.
Any help?

Is that the only USB drive that doesn't work with your MBP ?
Everything else works fine?

My flash drive doesn't work

When i inserted my flash drive in my mac it didn't pop up in my desktop like it always does instead it was like i didn't insert anything it worked in the morning i closed my laptop then took out my flash drive then i opened my laptop later and inserted the flash drive and it didn't work it doesn't even show on my finder what should i do? is my flash driver broken?

Choose Computer from the Finder's Go menu and see if it appears.
If it does, open the General tab of the Finder's preferences and check the box for it.
If it doesn't open the Disk Utility in the /Applications/Utilities/ folder and mount or repair it. If it doesn't show up there either, it's probably dead.
(116104)

After using TM My flash drive doesn't work on windows ! what should i do?

Hi everyone !
i Bought My Macbook Pro 2 Days Ago And This Is The First Time That I'm Using A Mac.
today i tried to make a backup of my Mac Os and i thought maybe i could use my flash drive , so i connected it and i opened the TM and it asked me that it should erase my flash drive so it can back up the files on it , but after doing all that stuff i found out that my flash's capacity is not enough for a complete backup, but now i cant use it like i used to, and it doesn't show up on my windows ... now how can i make it work normal ?!

it doesn't show up on my windows ...
If you mean 'wndows computer'... You will need to go to your Applications/Utilities folder and run 'Disk Utility'.
Plug in the flash drive, locate it on the left and click on the name to select it.
Then erase/format it using MS-DOS. When done, close Disk Utility and eject the flash drive.
Check it for proper operation on a Windows machine.
You can also erase/format it on a Windows machine or in a digital camera, as an example.
You can also format it for Mac OS, but I recommend keeping it Windows format for compatibility.
Good luck in any case.

Flash Drive Doesn't work on new macbook

I just got a new macbook pro. I plugged in my flash drive I use on my other macbook. Normally when it connects it lights up. I plug it into the new mac and it doesn't light up or show anywhere on the computer.

bamancabroad wrote:
Apple Care says it may be a bad hard drive and I should exchange the machine. However it was a special order, and it is a 6 week turnaround for a new machine. I use it for work, so that is a big issue.
If Apple offers you to exchange your machine and it is under warranty, by all means do it don't wait until your AppleCare expires.

External Hard Drive doesn't work on one usb, but works on the other, help?!

Hi there,
I have a very strange issue here. When connecting my external portable Maxtor 60GB disc to my MBP, I usually use the usb port on the right side of my laptop. However tonight, I connected it to the left usb port and noticed a horrible clicking sound coming from the otherwise silent drive. It made repeated clicking/scratching sounds and wouldn't mount and crashed OS X. Then I connected it to the right hand USB port and it mounted and worked like nothing else happened.
Has ANYONE experienced/can explain this bizarre phenomenon? Is it time to trade in my Maxtor for a new drive? I've only had it for a year and a half. Thank you!!

It's a power issue, use a 2-1 USB cord, a powered hub or an external power supply.

I have new hard drive in macbook pro(08) and have SATA cable with external power source to old hard drive (10.5.8)via. USB port and newer drive(10.6.8) will not recognize older drive..Do I need to partition newer drive with older disk to recover data?

I have new HD 750GB Hybrid in 2008 Macbook Pro 17" w/ Snow Leopard 10.6.8 connected to old Hard drive(250GB that had 10.5.8 on it at time of failure) via SATA cable to USB port with external power source.. Computer not acknowledging old HD at all in Disk Utility or otherwise (that I'm aware of)..Do I need to partition New HD and load old(10.5.8) onto partition to recognize older drive for data recovery? Thanks Wayno08

You do not need to load 10.5.8 onto your new drive in order for a 10.6.8 system to see the contents of a 10.5.8 system.
You might want to check out the hard drive troubleshooting bootk in the downloads section of this web site:
http://scsc-online.com
They also sell a product named Phoenix that can do OS extraction and volume copying/cloning, but to be honest I don't know if it's appropriate in this case.
I would suggest the following:
Open up Terminal.app (under utilities) and type "diskutil list" without the quotes. This is the command line version of Disk Utility. If the external drive doesn't show up at all, then it's likely not connected properly, not getting power, or just plain dead. If it shows up with only a devce name like disk0s16 but no volume it means the drive is seen, the OS just can't make sense of it.
Assuming the drive shows up, I would try to boot off the original installl disks for the system and run Disk Utility from that. I'm assuming the drive will show up. You'll want to select the option to repair the drive and then perform the option to repair the permissions.
If the unit isn't showing up, as per step 1, try a different USB port. More importantly with your unit, try it on another side of the unit if possible. If you read the book I referenced above, some of those units have I/O boards that are separated from the logic board. If the cable from the logic board to the I/O card goes bad or has problems, which isn't all that uncommon, some or all of the ports on the I/O card may appear to be bad as well. If you use a USB port on another side, it would be routing out of a completely different I/O path, so that's a potential problem.
If the drive is only seen with a device name such as disk0s16, it's likely either the index files are corrupt beyond Disk Utility's ability to see them. The only thing that I think would help would be a product named DIsk Warrior, but I can't guarantee that.
Disk Warrior can be found at:
http://www.alsoft.com/diskwarrior/
The company that I linked in the first link above also makes a product named Scannerz that does HD and system testing. The Scannerz/Disk Warrior combination make a good pair because the complement each other....Scannerz does what Disk Warriror can't and Disk Warrior does what Scannerz can't. However, at this point I'm not too sure getting a tool like Scannerz would be of much use because it sounds like the damage has already been done.
Let us know what happens.

Iphone doesn't work in my USB ports but everything else does, and iPhone works everywhere else!

My iPhone 3gs stopped working in the USB ports. Camera wizard doesn't even show up. Phone doesn't charge through it either, but if I plug my phone ANYWHERE else (computers and wall outlets) it works fine. When I plug keyboards and mice into my computer, they get recognized right away. My phone was working on my computer just about a week and a half ago, but just completely stopped. Can someone help me figure this out? I've read hundreds of threads from all over but can't seem to find the right answer. I'm going out of my mind here!!!

Did you do a restart, then if still not responiding then you need to do a restore through itunes.

Tecra S11-15T - GPRS modem doesn't work on internal USB port

My GPRS moden only works when I plug it into the dockingstation's USB port or if I use a USB port hub. If I plug it directly into the USB port on the laptop, I get an unknown device displayed in the device manager.
I have tried re-installing the chipset of my Toshiba Tecra S11-15T. I cannot get the device to work directly from the laptop's USB ports. I have WIN XP Professional.

Hi
Maybe the USB port does not provide enough power to get the modem working.
But all ports support the USB standards and every USB port is able to provide 500mA.
Possibly the modem needs more.
You can try to disable the USB power saving option.
In device manager, click right on USB root hub and go to Properties.
Then choose Power Management tab and uncheck the option; Allow the computer to turn off this device to save power

MS Word crashed and now my USB/flash drive doesn't work.

My MS Word crashed and when it recovered I got an alert saying my USB was not ejected properly (even though I didn't eject or remove it). I then removed it and put it back in and now my MacBook Air won't read it at all, and when I try it on a Windows laptop it says the drive is empty.
Please help! It has all my uni files on it!
Thanks so much.

Try plugging it into your MacBook and then repairing the disk permissions using Disk Utility.
Repairing a disk's permissions using Disk Utility.
Note: This should not delete any information or files from the disk.
Repairing a disk's permissions can help solve various file-related issues.
To begin, make sure your external disk that you are repairing is connected to the computer. If you are repairing an internal disk, skip this step.
After the drive is connected, launch the Disk Utility application in any of the following ways:
Type the first few letters of its name into Spotlight. Select it from the results.
Go Finder > Applications > Utilities > Disk Utility
Go Launchpad > Utilities > Disk Utility
Once you are in the Disk Utility app, select the external drive from the sidebar on the left.
Then, choose the Repair Disk Permissions button on the right.
If this does not solve your issues, you may have no choice but to reformat the drive using Disk Utility.
Austin

My flash drive doesn't show up on my desktop

Hi
All of a sudden my flashdrive does not appear on my desktop. It is plugged into my USB 2 socket on my iMac. Also, when I open disk utility, the application hangs. Is there anyway I can restore my flashdrive?
I think I may have unplugged my flashdrive before I ejected it!
Also, my imac would not shut down after my flashdrive had been inserted.
Hope someone out there can help.
Thanks
Phil
PS My flashdrive is a Sandisk CRUZER mini 512MB

Some USB devices have a nasty habit of sometimes not being recognised. I have found that usually this can be fixed.
Do not just plug it in and expect it to recognise it on the desktop. I know this will be a pain but turn your computer clear off, plug in the device and start your computer, I'll bet it will work then.
Also when you pull the USB from your computer scroll through your menu bar at the top and you will find that the USB device will show up in one of the icons and will allow you to safely remove it.
If you have been working along and decide you need to plug it in, chances are 70-30 it will not recognise it.
Several things can deternine this, The Operating System you have on your machine can be a factor.
I have an I-Omega Zip drive that will do this everytime.
I also have an older printer that will do it.
But like I said, If I plug it in and restart the computer it will recognise both of these devices.
Hope this helps. Don

Flash drive doesn't show up on desktop?

I have a f;lash drive that I've used for a long time to carry data between my home computer and my work computer. Suddenly it isn't showing up on the desktop of my MacBook Pro running the latest version of Yosemite. It does appear under devices in a finder window, but not on the desktop. I have restarted my computer, not just let it wake up from sleep, but that doesn't change anything. Any suggestions for how to get it to re-appear?
Thanks!

Do a backup.
Go to Finder and select your user/home folder. With that Finder window as the front window, either select Finder/View/Show View options or go command - J. When the View options opens, check ’Show Library Folder’. That should make your user library folder visible in your user/home folder. Select Library. Then go to Preferences/com.apple.desktop.plist and com.apple.finder.plist. Move the .plists to your desktop.
Re-launch Finder by restarting and test. If it works okay, delete the plists from the desktop.
If the same, return the .plists to where you got it from, overwriting the newer one.
Thanks to leonie for some information contained in this.

Flash drive doesn't fit in ss USB port

Similar Messages

Maybe you are looking for