Flash From Within, now won't charge. Please help
I have a 17 inch PowerBook 1.33, running the latest everything. I had my laptop plugged in (its a relatively new charger too, replaced recently) and was typing away with the laptop sitting on my lap.
I went to put it on the table in front of me, and at the moment that I put the computer on the table, I saw 2 blinks from within the computer. I saw these blinks through the left speaker, towards the top, right near where the charger plugs into the computer. As soon as that happened, the LED light on the charger went off, and the computer no longer thought it was charging.
I reset the PMU multiple times (shut down, ShiftControl+OptionPower Button, release, wait 5 seconds, start up computer) but to no avail.
I have a very depressing feeling that I blew something on the logic board, or soemthing happened that is going to require the loevely $700 charge from Apple to fix.
I figured I'd bring it into the Apple store and have Genius look at it, but I doubt that will solve anything.
Any help would be appreciated.
-From a poor college student who is freakin out.
A brand new battery would require a full charge in order to be used;
so you are lucky, in that the new battery had enough power already.
So that is not an indicator of much, other than the MagSafe Board
in the computer itself may have sustained damages due to ???
and would need to be checked over by an authorized tech or if you
are near an Apple Store with Genius bar, call ahead for appointment
to have a diagnostic test done and take along the MagSafe adapter
so they can see if that is part of the problem.
Of course, an optical drive issue could be part of a diagnostic check.
If you are in the US or Canada, the retail Apple Store offers a free
service of a diagnostic, even though the computer is no longer
covered by an AppleCare plan. So that is worth taking a drive...
Check the details here, and follow them to see if you can make it go:
•Intel-based Macs: Resetting the System Management Controller
http://support.apple.com/kb/ht3964
•About NVRAM and PRAM:
http://support.apple.com/kb/HT1379
Are the contacts on both the MagSafe adapter and MagSafe port
clean, or do they have an odd color or debris in/on them? It is
possible to clean them of debris, but don't use watery stuff. A
tool such as a wooden toothpick could be used to see if anything
on there could be rubbed off or out of the contact areas.
Good luck & happy computing!
Similar Messages
-
Mac Mini worked at first with Haier 42" plasma - now won't. Please Help!
I'd be interested in any resolution here. Here's my story:
I have a Mac Mini model MA723LL/A and a Haier P42LV6-T1 42" HDTV plasma with VGA and HDMI inputs. I first attempted to hook the Mac to the plasma TV using the DVI->VGA adapter that came with the Mac. I got no image at all on the TV, and the TV claimed 'No Signal'.
Then I used a DVI->HDMI adapter, and hooked the Mac to the TV thru the HDMI port. I got a picture and was happy. I setup iTunes, got the wireless working, surfed the web a bit and all was OK except the resolution seemed wonky. So I opened the Mac's settings panel to adjust the resolution, and as soon as I opened the settings panel, the screen went blank, with the TV claiming 'No Signal'. I shut off the Mac and rebooted, and from that point forward, what happens is this:
press On Button->
Apple Boot Screen->
MacOS 10 loading->
desktop For About 1 millisecond->
screen goes blank with TV claiming 'No Signal'
I hooked the Mac to my Dell 20" LCD monitor thru the monitor's DVI input and got a great picture. I tested all the resolution settings, and everything was fine. I have tested the Mac on the TV with all available resolution settings and it's always the same story (see above for sequence)
I'm kinda at the end of my rope. The Mac seems to be changing something on its video output at the end of its bootup, but I have no clue what. Has anyone seen anything like this? Any advice at all?Try what Apple recommends and see if that helps:
http://docs.info.apple.com/article.html?artnum=301345 -
Downloaded drivers from microsoft, now internet not working. please help
Internet connection lost after downloaded drivers updates
Install drivers from motherboard/notebook support pages.
I do not use optional updates, namely MS drivers.
Sometimes removing driver in Device manager and restart may cure your computer.
Consider HW and operating system update. From the point of view of security it is not wise to keep using Windows XP.
Rgds
Milos -
New Nano won't charge - please help!
Hey guys! Hoping you can help me.
Bought a new Nano 4g 2nd generation. I plugged it into my laptop, installed it and put music onto it. When I disconnect it, there is no battery life, even though it was plugged in for hours. I also have an AC adapter, and have plugged it into that, and when I disconnect it, the menu on the screen just disappears and I can't turn it on again.
This is the 2nd time I've bought a brand new iPod that has been faulty out of the box. I've tried the 5 R's and nothing seems to work. I know I may have to send it away to get a new one (shudder) but I just wanted to know if anyone else has had this problem, and if so, what eventuated?
Many thanks in advance!Same Problem with one I gave my daughter for Christmas. Purchased online direclty from Apple. What's the fix? DON'T IGNORE THIS ONE GUYS!
-
my mac doesnt recognize my ipod nano G4, its always worked before. read the trouble shoots, checked all connections. it needs to charge and wont do it.
Try the suggestions in article - iPod not recognized in iTunes and Mac desktop. If the suggestions do not work, more than likely you need a new battery. Take the iPod Nano to an Apple store or an AASP. Whichever is more convenient for you.
-
HELP NEEDED!! I bought a brand new mac air 11 inch a month ago, and for three days now I can't switch it on.when I do, i can hear the machine is on, but nothing else happens. (yes it is charged). please help.
I bought it in South Africa and I am currently in Israel.thank you for the response.its not working, tried that. i can switch the machine on and off, can hear the machine when i hold it to my ear. but nothing works, not the screen, not the sound, nothing.
-
Since upgrading to Yosemite on my iMac: My Mail app refuses to open, Safari won't load, and I can't upload pictures from my iPad...
Please help, any ideas very welcome. I've had my iMac since 2011, and have never had any issues to deal with before..
Thanks29/11/2014 20:17:01.315 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 11 seconds. Pushing respawn out by 49 seconds.
29/11/2014 20:17:37.013 com.apple.backupd[616]: Finished scan
29/11/2014 20:17:43.108 com.apple.backupd[616]: Saved event cache at
/Volumes/Time Machine Backups/Backups.backupdb/Geoff Lambrechts’s iMac
(2)/2014-11-29-200648.inProgress/9B453663-603F-40B8-AC21-24F05C724E15/.6162AD34- 38F8-30AB-98E0-4A22FB9D311F.eventdb
29/11/2014 20:17:43.207 com.apple.backupd[616]: Not using file event
preflight for Macintosh HD
29/11/2014 20:18:01.561 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 11 seconds. Pushing respawn out by 49 seconds.
29/11/2014 20:18:16.288 com.apple.xpc.launchd[1]:
(com.apple.quicklook[715]) Endpoint has been activated through legacy
launch(3) APIs. Please switch to XPC or bootstrap_check_in():
com.apple.quicklook
29/11/2014 20:18:23.705 com.apple.SecurityServer[56]: Session 100013 created
29/11/2014 20:18:32.046 mdworker[718]: code validation failed in the
process of getting signing information: Error Domain=NSOSStatusErrorDomain
Code=-67062 "The operation couldn’t be completed. (OSStatus error -67062.)"
29/11/2014 20:19:01.662 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 11 seconds. Pushing respawn out by 49 seconds.
29/11/2014 20:19:45.458 com.apple.xpc.launchd[1]:
(com.apple.imfoundation.IMRemoteURLConnectionAgent) The
_DirtyJetsamMemoryLimit key is not available on this platform.
29/11/2014 20:19:59.123 com.apple.xpc.launchd[1]:
(com.apple.PubSub.Agent[725]) Endpoint has been activated through legacy
launch(3) APIs. Please switch to XPC or bootstrap_check_in():
com.apple.pubsub.ipc
29/11/2014 20:19:59.123 com.apple.xpc.launchd[1]:
(com.apple.PubSub.Agent[725]) Endpoint has been activated through legacy
launch(3) APIs. Please switch to XPC or bootstrap_check_in():
com.apple.pubsub.notification
29/11/2014 20:20:01.138 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:21:01.484 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:21:13.430 com.apple.backupd[616]: Found 4529 files (1.1 GB)
needing backup
29/11/2014 20:21:18.786 com.apple.backupd[616]: 2.82 GB required (including
padding), 1.24 TB available
29/11/2014 20:21:31.775 Console[734]: Failed to connect (_consoleX) outlet
from (NSApplication) to (ConsoleX): missing setter or instance variable
29/11/2014 20:21:34.230 WindowServer[162]: disable_update_timeout: UI
updates were forcibly disabled by application "Console" for over 1.00
seconds. Server has re-enabled them.
29/11/2014 20:21:36.898 WindowServer[162]: common_reenable_update: UI
updates were finally reenabled by application "Console" after 3.67 seconds
(server forcibly re-enabled them after 1.00 seconds)
29/11/2014 20:21:36.971 coreservicesd[83]: SFLEntryBase::ListHasChanged
mach_msg returned 10000004d
29/11/2014 20:22:01.817 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:23:02.170 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:24:02.547 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:25:02.168 CalendarAgent[218]:
[Refusing to parse response
to PROPPATCH because of content-type: .]
29/11/2014 20:25:02.233 CalendarAgent[218]:
[Refusing to parse response
to PROPPATCH because of content-type: .]
29/11/2014 20:25:02.236 CalendarAgent[218]:
[Refusing to parse response
to PROPPATCH because of content-type: .]
29/11/2014 20:25:02.284 CalendarAgent[218]:
[Refusing to parse response
to PROPPATCH because of content-type: .]
29/11/2014 20:25:03.059 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:25:12.674 com.apple.xpc.launchd[1]:
(com.apple.imfoundation.IMRemoteURLConnectionAgent) The
_DirtyJetsamMemoryLimit key is not available on this platform.
29/11/2014 20:26:03.464 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
29/11/2014 20:27:03.841 com.apple.xpc.launchd[1]: (jp.buffalo.NASPower)
Service only ran for 10 seconds. Pushing respawn out by 50 seconds.
On 29 November 2014 at 19:29, Apple Support Communities Updates < -
I have the new IPad and can't connect via bluetooth to any of my apple devices (IPhone 4s and appleTV) neither from my new IPhone 4s. When I turn the Bluetooth on, both devices keep in searching mode... I don't know what to do now... Please help... I can't pair any device because they can't find whitin themselves.
Wmorlac wrote:
I have the new IPad and can't connect via bluetooth to any of my apple devices...
Correct... See Supported Bluetooth Profiles Here...
http://support.apple.com/kb/HT3647
Suggest you check the User Guides of your Devices to find the Method of what you are trying to do -
I have an account from Australia but I now live in Switzerland. I bought a Swiss Gift Card but I can't redeem it because I have 41 cents left from my Australian Gift Card. Please help me !
The only way to get rid of those little leftover balances is to make a request to iTunes Customer Service:
http://www.apple.com/support/itunes/contact/
Once they get it zeroed out, you will be able to enter your new Swiss billing credentials. -
From the past 3days,i can't install apps from the appstore,it says "this items can't be purchased right now,try again later", please help me,thank you
Hey Kay97,
These are some troubleshooting steps that might be relevant to your issue:
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
Welcome to Apple Support Communities!
Have a good one,
Delgadoh -
I just downloaded the new iOS7 onto my iPhone 5 and now I can not get my iMessage to activate with my Apple ID! My iPad connected just fine but my iPhone won't. Please help
I would go to Settings - General - Reset - and Reset Network Settings
Try it again after the phone restarts -
Hi ! I have an iPhone 4s , bought it from apple company , I have charging problem , very slowly , it sometimes takes all day of charging , please helpe ...
In most countries they will do so for a fee. US$199 for a 4S. It may just need a new battery, which Apple will install for about US$70.
-
Help my IPOD won't start PLEASE HELP
It gives me the apple screen and then switches into the foloer with an exclamation point and i don't know how to get it out. I have tried restarting, and plugging it into the computer doesn't do anything. It is charged, please help.
Hello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921�
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote -
After install ios 7 wifi won turn on please help....
after install ios 7 wifi won turn on please help....
Thanks for the update. I don't know if you have tried this, but I would next I would try removing and re adding the mail account from the phone, then testing the issue again:
Delete the affected email account from your device.
Tap Settings > Mail, Contacts, Calendars.
Choose the affected email account, then tap Delete Account.
Add your account again.
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
If it persists, I would next backup your device to iTunes with this article:
iOS: How to back up and restore your content
http://support.apple.com/kb/HT1766
And restore it from your backup with this article:
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/ht1414 -
my ipod nano 7th generation....works fine as long as it's on the docking station. when off the station, the display goes dark after a few seconds. it's fully charged. please help. this is the heartbeat of my business. thanks
In the worst case, it's still under warranty (all 7th gen nanos are still under one year from purchase).
So, you disconnect it from power, and it almost immediately goes dead? You can try a Restore... but it doesn't sound like the type of problem a Restore will fix.
You should probably have it looked by Apple Tech Support. If there's an Apple Store nearby, you can take it to the store's Genius Bar. To avoid waiting, you can make a reservation at the store's web page
http://www.apple.com/retail/
Maybe you are looking for
-
Getting Blue Screen error BCCode: 1a
Sometimes mi PC with windows VISTA have espontaneus Blue Screen Error.Then after startup I would get this message,can someone tell me what I shshould do? Problem signature: Problem Event Name: BlueScreen OS Version: 6.0.6002.2.2.0.768.3 Locale ID: 11
-
XML Page cannot be displayed -- whitespace is not allowed at this location
To create an online training program I am using Captivate 3 to create the videos then move the published flash file into Contribute 3 to create the XML and HTM files. Using the same publishing steps most videos play; however, some videos do not. I no
-
Character set problem with db link
Hello, I'm accessing a DB2 database through a database link (ODBC) and I'm getting this error: ORA-28500: connection from ORACLE to a non-Oracle system returned this message: [Generic Connectivity Using ODBC]DRV_GetRows: DB_ODBC_ENGINE(1125): ; [IBM]
-
TSD(Technical specifications document) for webdynpro iview
Hi, Do we hav any standard template to prepare TSD for WEBDYNPRO-IVIEW as we hav it for reports and interfaces?Please send it to me as soon as possible if u hav it,i need it immediately in my project work. Thanks, Deepthi.
-
How to Enable Logon & Logoff sounds? Please help! :(
I really would like the Logon and Logoff sounds please is there anyway i can get them back?