Flash media and keepout 600 physical nand black offset 1

My screen is frozen and this is the message at the top of the screen. Help~please!

Any physical or liquid damage to the iPhone?
First try a reset:
- hold the home button and sleep/wake button down at the same time
- the iPhonw qill turn off(keep holding) then as soon as you see the Apple logo appear release both buttons
If the issue remains then try plugging it into a PC/Mac with iTunes and see if it will be recognised. If it is recognised then back it up and then restore to factory settings. If all steps fail then [book an appointment at an Apple Store to have the iPhone evaluated.
All the best

Similar Messages

Ipad 3 wi-fi - nand flash media is keepout : 688 physical nand Block..

Hi,
i Need help how to fix it?
Need your guides how to fix it, my ipad warranty is expired. according to apple repair this item cannot repair need to replace 1 to 1. since the warranty expired than i need to up the money MYR 1,300.
Please guide me what should i do?
it's logical board? its flash problem, or something else please advice.
please refer this links:http://www.ifixit.com/Answers/View/138480/The+Error+is+nand+flash+media+is+keepo ut+%3A+688+physical+nand+Block..

I'm sorry but this item is 1 year and a few months old? damage to nand is not something you'd expect from normal wear and tear and therefore not caused by you. I'd contact Apple again. Be pushy, write emails, ring them. There are people who'd be able to replace this but finding them is the problem. good luck
pollytintop, 1 hour ago
Thanks pollytintop for your advice- I’m still keeping looking forward how to fix it. Will not this item (ipad) throw become rubbish due to damaged that do not know cause and cannot repair or fix it? Hope somebody highlighted this issue to Apple (the best customer service ). Thanks

My phone was jettisoned into a hot tub. Now I'm getting "_FindFlashMediaAndKeepout:600 physical nand block offset 1". what do I do?

My phone was jettisoned into a hot tub. Now I'm getting "_FindFlashMediaAndKeepout:600 physical nand block offset 1". What do I do?

If you can turn it off, do so and put the device in a sealed bag of uncooked rice for 3-5 days. After that, you can try and charge it and see if it will work. If not, you will need to purchase an OOW (out of warranty) replacement. See this link for costs in your area. Go to the Warrant & Service pricing section after selecting your area.
http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipho ne

HT201263 [NAND] Find Flash Media And Keepout Error

[NAND ] _FindFlashMediaAndKeepout :601 physical nand block offset 1
[NAND ] start :356 this 0x9f538400 PROVIDER=0x9f6b1f00 flashMedia=0x9f6b1f00
[NAND ] WMR_Start : 149 Apple PPN NAND Driver , Read/Write
[NAND ] WMR_Start : 174 FIL_Init [OK]
[NAND ] WMR_Open : 371 VFL_Open   [OK]
[NAND ] s_cxt_boot : 88 sftl : error , unclean shutdown; adopted 11280 spans
[NAND ] WMR_Open : 420 FTL_Open   [OK]
[NAND ] _publishServices : 642 FTL capabilities : 0x00000001
[NAND ] _ppnvflGetStruct : 3469 Checking borrowed blocks - count : 23 max_count : 23
[NAND ] _fetchBorrowedList : 881 number of borrowed blocks 16
Above is the error that I started receiving this morning. The phone wasn't plugged into anything and appeared to have turned off due to a low battery. The phone was unresponsive when I hit the lock screen button or home button. When I plugged it into a wall outlet with the original USB cord and wall adapter, it initially showed that it had a low battery. After a few minutes once it had enough power to start, the Apple logo displayed normally for a few seconds and then the screen went dim and displayed the above error.
I then pushed and help the lock screen button and home button together until it turned off to hard reset it. I held the home button and plugged it into my Mac Mini so that it would go into recovery mode.
When iTunes finally gives up, it will throw an unexpected error of either 4005 or 4013
I've seen similar discussions such as:
iPhone 4S Stuck at boot showing [NAND] ?                                                 https://discussions.apple.com/thread/4109291?start=0&tstart=0
Well I was using my iphone 5, When ..... i get the same error ,                    https://discussions.apple.com/message/23051809#23051809
My iphone 5 wont move ..... offset 1 Someone PLEASE HELP ME!              https://discussions.apple.com/message/21809003#21809003
and several others but none of which have been helpful. I've seen some actual Apple employees post on the discussions but nothing useful; the typical have you read the troubleshooting steps, here's some links to error messages, etc...that don't explain what this issue is and what I can do to resolve it.
Any help would be much appreciated.
Mr-apple

https://discussions.apple.com/message/26136922#26136922

My iphone 5 has gone to a screen with apple logo and message saying find flash media and keep out. I cannot do anything with my phone. can soomeone help.

my iphone 5 only has apple logo on screen with message saying find flash media and keep out. What does this mean, i cannot do anything with the phone

thanks

Iphone 5 error message on the top saying, 601 physical nand block offset 1.

iphone 5,on the screen, apple logo on and some error message on the top saying, 601 physical nand block offset 1. once i remove the cable from laptop to phone it goes on dfu mode and can't restore the phone because of some unknown error. please help.

yeah i am on my way. lets hope they will fix.
thanks.

What is 429 physical nand block offset 16

this iPad in business had the following error message when turned on:
NAND] _FindFlashMediaAndKeepout :429 physical nand block offset 16
[NAND] start:220 this 0x97aedc00 PROVIDER=0x97b9c500 flashMedia=0x97b9c50
[NAND] WMR_Start:149 Apple PPN NAND Driver, Read/Write
[NAND] WMR_Start:174 FIL_Init [OK]
It was erased and reset to default settings then after a month or so, the error came back.

Hi, my ipad 2 just got the same problem and after reading all relative post, finnally i figrue it out, that is no software issue at alll just hardware,
I did attemp replace the power button cable on my ipad so i must disconnect the back camera cable so there is my problem. Because the connect some how not exact in place, i took the camera out and the issue is gone. So, in your case, if you did try to replace anything look at them again or you just take them out one by one and reboot ipad until it work.
Hope this help
Binh

Findflashmediaandkeepout 601 physical nand block offset 1

A couple days ago, my phone got slightly wet. I soaked it in rice for a day then let it sit in a fairly warm room/area to air dry for most of the next day. The tird day, I looked over my phone and saw that it appeared to be completely dry so I allowed it to charge. When I plugged it up, I saw the usual Apple logo then 2 seconds later an error message popped up at the top of the screen. This is the main phrase: "findflashmediaandkeepout 601 physical nand block offset 1"
Seconds later, the message would disappear, but the Apple logo would remain for a few moments, disappear, reappear, etc. The phone is unresponsive to the pressing of just one button (home or power), and shuts off for a maximum of 25 seconds when pressing the buttons in unison.
I know I should take this to the Geniuses but I'm in desperate need of answers now.. Can anybody help me fix my phone or even help me understand what this error code means?????

Hi mmmaaaaany,
Welcome to the Apple Support Communities!
If your iPhone is unresponsive after getting slightly wet, it may be necessary to have your iPhone evaluated for repair. If you choose to set up the repair, you can follow the links on the attached website to set it up.
iPhone Other Repair Options - Apple Support
Have a great day,
Joe

[NAND ] _FindFlashMediaAndKeepout :601 physical nand block offset 1

Hi!
I Need help! Can anyone help me?
My phone crashd very hard on the floor... everything at the Display was destroed..
I've changed the Display an now Shows me an error... I dont understand what this means!
Can anybody read this error and tell me, which part or what else is terminated or any Flex?
Screen is new, touch works... but when i restore my phone, Shows me this error...
thanks and sry 4 bad english
My Error:
[NAND ] _FindFlashMediaAndKeepout :601 physical nand block offset 1
[NAND ] start :356 this 0xa18e0400 PROVIDER=0xa04f5e80 flashMedia=0xa04f5e80
[NAND ] WMR_Start : 149 Apple PPN NAND Driver , Read/Write
[NAND ] WMR_Start : 174 FIL_Init [OK]
[NAND ] WMR_Open : 371 VFL_Open [OK]
[NAND ] s_cxt_boot : 88 sftl : error , unclean shutdown; adopted 3494 spans
[NAND ] WMR_Open : 420 FTL_Open [OK]
[NAND ] _publishServices : 642 FTL capabilities : 0x00000001
[NAND ] _ppnvflGetStruct : 3469 Checking borrowed blocks - count : 25 max_count : 25
[NAND ] _fetchBorrowedList : 881 number of borrowed blocks 18

It's always risky opening an iPhone, which is why Apple considers it serious enough so they won't fix a phone that has been opened. This error means that the SSD memory control has detected a failure. It could be a flex not inserted fully, but it could also have been a static discharge when the case was opened because whoever did the repair did not do it on a copper ground plane and/or was not properly grounded him or her self. It's really pretty much impossible to diagnose a hardware fault without proper test equipment. If the front camera problem occurred before the phone was opened it is unlikely to be related to this newest problem. You can check for water damage by removing the SIM card and looking in the empty SIM slot with a bright light. If you don't see any red dots then water probably did not get into the phone, so that would be one less concern.
What happens if you do a reset (hold the HOME and SLEEP buttons at the same time until an Apple logo appears)?

HT201412 Apple IPAD has crash with [NAND] _FindFlashMediaAndKeepout:429 physical nand block offset 16 error

Today my IPad has crashed with this text at the top of the screen - it keeps rebooting bu won't go any further past this piece of text.
The full error text shown is:
[NAND] _FindFlashMediaAndKeepout:429 physical nand block offset 16
[NAND] start:220 this 0x9c0b6c00 PROVIDER=0x9c0b5c00 flashmedia=0x9c0b5c00
[NAND] WMR_Start:149 Apple PPN NAND Driver, Read/Write
[NAND] WMR_Start:174 FIL_Init [OK]
And then gets no further.
What is this, does this mean something has burnt out and how do I get the tablet repaired ? I live in the UK and the serial no. of the 16 GB IPad is:
DN6HDMTNDFJ1
I so need this tablet for my work and need to get it back up and going again.
Many thanks,
Jayne

Have you tried resetting it? I.e. Hold down the sleep/wake button and the Home button simultaneously until you see the Apple logo appear, then release them and see if the iPad will startup okay.

My ipad3 will not turn on except to display the following[NAND] _FindFlashMediaAndKerpout:429 physical NAND block offset 16 [NAND] start:220 this 0xa015cc00 PROVIDER=0x9ed20080 flashMedia=0x9ed20080 [NAND] WMR_Start:149 Apple PPN NAND Driver, Read/Write

Help. My ipad will not boot up except to show the following message.
[NAND] _FindFlashMediaAndKerpout:429 physical NAND block offset 16
[NAND] start:220 this 0xa015cc00 PROVIDER=0x9ed20080 flashMedia=0x9ed20080
[NAND] WMR_Start:149 Apple PPN NAND Driver, Read/Write
Ideas? Help

Hi, my ipad 2 just got the same problem and after reading all relative post, finnally i figrue it out, that is no software issue at alll just hardware,
I did attemp replace the power button cable on my ipad so i must disconnect the back camera cable so there is my problem. Because the connect some how not exact in place, i took the camera out and the issue is gone. So, in your case, if you did try to replace anything look at them again or you just take them out one by one and reboot ipad until it work.
Hope this help
Binh

My iPhone 5 fell into the water and writing like this showed up with the apple sign.[NAND]_FindFlashMediaAndKeepout :601 physical nand block offset 1 [NAND] start :356 this 0x96fec400 PROVIDER=0x96193b80 flashMedia=0x96193b80 [NAND] WMR_Start : 149 Apple

my iPhone 5 fell into the water and a writing like that appeared with the apple sign. (when its turning on) but it is now a gray screen and it is not working, nor can i connect it to my laptop.

You're seriously trying to use an electronic device that's been in contact with water????
You do know that since th beginning of time water and electricity don't mix, right?
Start being smart and top trying to use it NOW, and put it in a bag of rice for a week.

I too face the dreaded [NAND ] _FindFlashMediaAndKeepout :601 physical nand block offset 1 [NAND ] start :356 this 0x9f538400 PROVIDER=0x9f6b1f00 flashMedia=0x9f6b1f00 [NAND ] WMR_Start : 149 Apple PPN NAND Driver , Read/Write [NAND ] WMR_Start : 174

I've seen a few other people who have also had this issue, and their problem turned out to be some kind of camera flex thing, or a main logic board. I have an iPhone 5C iOs 8. I get that weird error message when trying to turn my phone on, after it randomly turned off this morning. Recently, I did have the screen replaced (for the second time) by a THIRD Party. Yes I know, I've voided the warranties, blah, blah blah, please don't crucify me. Now, the phone will bring up the apple logo on a black screen, but it does nothing. I'be tried to restart etc, and may have accidentally wiped out my phone by putting it in recovery mode. But oh well. Also worth noting is that my front camera hasn't worked in a few months, but I did nothing about it. Could the front camera problem be related to this? I also dropped my phone in the sink last night, but it was in its life proof, dried immediately and kept working fine. I have had nothing but problems with this phone, and if anyone has any advice, PLEASE HELP. Thanks.

I don't believe any of us here can do anything to help you other than to suggest that you take the device back to the third-party that did the repair and have them do the repair correctly.

Please help, need to import .swf/flash media

Hi all, have a little issue here. I have some SWF flash media and I want to bring it into imovie so I can edit it more effectivley then with qt. However, I have been haveing alot of trouble, most time I only get the audio part of it and no image. Most of the media is widescreen, I was able to export the media in qt to dv stream and then import it, however, it lost its widescreen look and was kinda squished from the sides if that makes sense, if anybody has expeirence with this type of media, please help.
Nathan

Hi Nathan,
I've never "dared" to convert .swf, but I read a lot about problems doing so... probably the Quicktime section of this forum is better to ask...
maybe a much easier workaround is using tools as SnapzPro from Ambrosia; this tool claims to "record" any screen content (and audio) and convert it directly into any wanted format (as dv)...
just a thought.......

Excessive Heat generated viewing Flash Media

I have a Apple Powerbook 15" w/1.6 Ghz, 2 GB SDRAM, OSX
10.4.10
I loaded a temp tool to read processor heat in real time.
With machine at idle, the temp is right at about 100F
Go to any video with Flash Media, and the temp reaches 155F.
I just checked the version of Flash Player, and it is V9
Processor Activity Monitor is also maxed out.
Why is it cheap portable DVD players have no issues with heat
or huge processor loads?
It's not enjoyable watching ones Motherboard melt every
soldered socket just to watch a micro video.

Your laptop is not overheating at all. If those were Celsius,
then we have a reason to be worried. Laptops are not the best for
heat management, you have no reason to be worried. Your temps are
fine. The activity monitor is maxing out because whatever you are
watching is obviously very processor intensive, and you are lacking
in that department. Overall, you are fine, and this isn't a Flash
Player issue. Why are cheap portable DVD player able to handle
this, well, that is what they are made for, and solely for that
purpose. They play DVDs and that is it. You have a computer, with a
slew of moving parts, and processes running in the background. If
your computer only played DVDs, than that would be all it is worth,
but you can play DVDs, burn DVDs, surf the web install
applications, the list goes on and on.

Flash media and keepout 600 physical nand black offset 1

Similar Messages

Maybe you are looking for