Flash media encoder 3.2 and black magic intesity pro 8.6 drivers

ok so here is my problem im capturing a source with compnent cables and after about 12 hrs i drop 1 frame on input from 30fps to 29fps.. my output is 29.97 and when this happens video lags to flash media server.. here is the funny part this doesnt happen ever on my x6 amd cpu using onboard video
The affected system is a 2600k with a 6850 xfx gfx card..
so what could problem be?
p.s both bmc are working fine in amd nothing wrong with them
now keep in mind i reset the fmle but this is how its configured

no one knows?

Similar Messages

Flash media encoder always disconnect and reconnect

flash media encoder 3.2 always disconnect and reconnect to both primary and secondary urls every about 10 minutes while using with wowza server
any help

When this happen to me it was becuase The interent was too slow.

Flash Media Encoder 3.1 and 3.2 / SigmaTel - no sound!

Hi there, I have Dell XPS 420 with SigmaTel on board,
cant get any sound output, both in XP and windows 7 but can hear sound ok through speakers but sound levels not moving and you cant adjust the AudioInputMixerProperties Master Input Mix, all greyed out,
however if I use old PCI sound card it works ok! Had no problems before on old PC, just this one.
Any help much appreciated!

Hi there and thanks for trying to help, but as mentioned above, you cant adjust the AudioInputMixerProperties Master Input Mix, all greyed out and you only got line out, microphone settings, I have clicked on all of them to no avail, i feel its the buttons on the left in this that need to be changed but you cant click on them or move the sliders, as if theres no sound on board at all...
Now that I have removed the old sound card that I was testing with it has gone back to the original way it was before tried to trouble shoot myself with another sound card and says when loading:
"No audio capture devices detected
Flash media live encoder requires an audio capture device to be connected and properly installed."
Also, when you tick the Audio box it comes up:
"No Audio capture devices detected
Flash media live encoder requires an audio capture device to be connected and properly installed"
and if you try and click on Device (which is empty) the program closes down (without any error message) and also you cannot click on the wrench as thats greyed out.
It just dont seem to recognise my on board sound card, but strangley enough when I put in old sound card you had the option to select it but still no sound from it, shame my other sound card is faulty (only works for about an hour - believe faulty capacitor) as would use that, dont really want to have to buy a new sound card just for this when I have used this many times no problem on old PC with onboard sound. As mentioned, everything else sound wise works ok no problems.

CS6 Premier Pro and Black Magic Intensity Pro not working?

Hi,
I am using the trial version of CS6 Premier pro. First the Playback settings in the drop down menu next to the viewer is greay out. Second, when I go into the playback setting through the settings menu I dont see the Black Magic as an option to send my signal out to. Is this a limitation of the trial version?
I have updated everything and the Black Magic works perfect with my CS5 and Final Cut Pro.. Any clues?

Hi Javier,
The new Mercury Transmit plug-ins from Blackmagic and other hardware partners are selected in a different way than the previous player plug-ins from CS5.5 and earlier. To turn on transmit, go to the Preferences, in the Playback area. There, if the plug-ins for your third-party hardware are installed correctly, you'll see options for the Audio Device and Video Device. Once you select the third-party hardware there, it can be used across sequences and projects. If the transmit plug-in provides a setup dialog for additional options, you'll see a small setup option on the right side of the Video Device option.
And of course, make sure that you have applied the latest CS6 updates, and are using the latest installer from Blackmagic for CS6.
Cheers,
Zac

Flash Media Encoder 2.5

Hi--
I'm using Adobe Flash media Encoder 2.5 to stream Video & Audio to a web-site. For the past few days I've been unable to access my Channel on that web-'s Player or ANY other channels on the web-site-- after eliminating the browsers (as all 3 experience the same issue of non-accessibility to the web-site Player),and the fact that all 3 browsers PLAY OTHER Flash-encoded content, I have deduced the problem is with Flash Media Encoder as it keeps re-setting every 20 seconds or so indicating "Encoding & streaming to server is stopped due to aproblem in capturing Audio/Video"--however the settings are the same as when there was no problem. Anyone familiar with Flash Media Encoder 2.5 and any problems it may be experiencing? This has been ongoing for 4 days now
Screenshot below
Nleibo

I had the same problem and just resolve it a few minutes
ago!!!
ok for example if I need to add a user named "joe" and his
password will be "1234" I will type the following at the momand
promt:
users add -u joe -p 1234
please let me know if it's works

Adobe Flash Media Encoder 3.0 Crashes

Hi, i just installed the new Adobe Flash Media Encoder 3.0 ,
and when i start it all it does is show up the main screen and then
closes automatically NO error messages at all!! Adobe Flash Media
Encoder 2.5 works fine... Any Fix or idea why ?

sort of same issue here, I downloaded encoder 3.0 and it crashes my pc about 20 seconds after start encoding any suggestions, it also now has issues getting into my livestream.com studio
And where do i try and delete the xml im dumb
steve

User Auth. for Live Streaming with Media Encoder 2.5 and FMSS

Hi,
i am currently thinking of buying the Flash Media STREAMING
Server (~995 $) and in order to see if this is the right choice, i
also take a look at the Wowza Media Server for comparison.
I want to support Live Streaming from Events with Flash Media
Encoder 2.5 and for this i'll need a user authentification for
giving access to special publishing Users only. Wowza Media Server
supports a User Authentification by parsing the connecting URL,
witch is delivered by the Media Encoder on starting a Connection,
and therefor grants or denies access to the publishing function.
Only Users with the right Access Persmissions, which is written
trough a password and the onPublish Comand in the url, can publish
Live Streams. Everyone can watch the Live Stream, if no restriction
to the onConnect Command was made.
The Problem in this case is, i will need seperate Application
folders for every user who should be able to start a live stream.
This would be a horrible effort...
more info ==>
http://www.wowzamedia.com/forums/showthread.php?t=1281
Is there a similar way to support authorisation for starting
publishing a LiveStream to the Flash Media Streaming Server, or do
i need the Flash Media Interactive Server?
How can i restrict access to users, who should not be able to
start a live stream on my FMSS?
Thx for your help,
Tobi

quote:
Is there a similar way to support authorisation for starting
publishing a LiveStream to the Flash Media Streaming Server, or do
i need the Flash Media Interactive Server?
Unfortunately no, there isn't. I struggled with same issue
earlier, and we were forced to purcahse the Interactive edition. As
the 'Streaming' version only runs Adobe-signed apps, there is no
way to change things that happen within the onConnect handler.
Furthermore, guys at Adobe haven't provided any possibility for
even simple access control through configuration files for built-in
apps that come along with the Streaming Server edition.
- Jakki

Adobe Media Encoder CS4 Suddenly Adding Black Bars To L & R

I think I may be going crazy.
Every video I have ever shot has been cropped to 720x340 in After Effects then exported as an uncompressed Quicktime movie file at 720x340. For the last year I have done this process exactly the same everytime.
On my website (www.stevenbogda.com) videos are either 360x170 or 480x226 FLV files, both variations of the original 720x340 Quicktime file. I would just bring a 720x340 file into Adobe Media Encoder CS4, adjust the dimensions and bitrate and export and it would work perfectly. Now all of the sudden, when I bring anything I shot and exported recently into AME CS4 to get it ready to go on my website, it adds BLACK BARS to the left and right side of my video (refer to image 2).
I thought it was just a visual problem in AME CS4 until I exported it as the FLV file that I planned on doing, just to find that the actual FLV file is in fact the dimensions I wanted, EXCEPT it has black bars on the right and the left...
I immediately blamed it on After Effects and started re exporting uncompressed Quicktime files with different settings and managed to get AME to work properly but it was random. Some videos were exported with "settings 1" and worked in AME but other videos with the same settings didn't work.
I went to my hard drive where I store my master Quicktime files that were used to make the videos on my site and brought some into AME CS4 and they acted the same way that the new videos I made do, with black bars on the left and right. These videos worked the way I wanted them to in AME CS4 last month, but now suddenly are doing what my more recent files do and I have no idea why.
I found out that by lowering the width of the video (refer to image 3) the black bars would dissapear slowly, but then the video would be a smaller width that it should be. I really think I am just missing something, or set some setting wrong by accident because this never used to happen and now is happening with files that once worked correctly.
Any help or ideas would be greatly appreciated because I am spending way too much time re exporting uncompressed files just to find out they don't work.
Thank you,
Steven

Stan,
I was using the on2VP6 codec at data rates from 275k to 400k with good results. -- with the new CS$ endcoder i am used h.264 at 500k to 700k, video quality looks good but the graphic overlays look like alised crap. In the encoder settings the edges of the graphics get jaged when I make the field order progresive...
I am starting with DV NTSC video at 720x480.
I am going to go back to my old work flow and test it. The settings are a bit different from premiere pro 1.5 to CS4 -- in 1.5 i could export out an unconpressed .mov with square px and then bring that large file to flash media encoder to create the .flv

Flash Media Encoder 3.1 Problem..

Okay so.. I just recently decided to start broadcasting on my new laptop which is windows 7 and a 64 bit and I reinstalled my Pinnacle software on this labtop and when I install the drivers and other needed programs such as this. So moving on to the problem, like many other people from what I see have similar problems like me about when you open Flash Media Encoder and then swap to your capture card it loads then black screens and finally instantly closes without warning.. I have pretty much gone through an ENTIRE day trying to get this to work.. I also went to my old labtop and tried it out there and for some reason it works an dis compatible there... Please I would appreciate some help as I would like to start broadcasting again..

Please try using FMLE commandline version FMLECmd and see if it works?
FMLE GUI has a known issue on Windows 7 starter and Home edition

Flash Media Encoder 3.1, ManyCam, SigmaTel, Windows XP - No Audio output to FME or to Justin.tv

I have adobe flash media encoder 3.1 installed and am trying to stream downloaded .avi, .mpeg, and other video files to justin.tv using ManyCam, Everything seems to be working fine, video stream is clear and not choppy. Audio on my end is clear, and in Flash media Encoder i have "SigmaTel audio device" selected as my audio output (which is my stock audio driver)..however i keep getting complaints that there is no sound to my page on justin.tv. As far as i know all my drivers are installed properly and up to date. The green audio bar on FME shows no activity. Im wondering if this ****** SigmaTel excuse of an audio driver just doesnt get along with FME? There is no option to select "stereo mix" as other forums have said to do. Can anyone please help me get sound to my justin.tv page? Or help me find a way to instal a different audio driver that is compatible with a dell piece-o-**** dimension e520. I have downloaded Realtek HD Audio, SoundMAX drivers, and a few others but the only audio driver this piece of **** dell wants to recognize is the SigmaTel Audio Device, Which WONT OUTPUT SOUND TO FME!!!!!! PLEASE HELP!! TUMOUR IS GROWING!!
Can i not buy a set of surround sound speakers that are hooked up via USB and go around this problem? I really just want to get RID of SIGMATEL forever, and use REALTEK...but it wont recognize no matter how many times i download it. fml!

"The audio preview in FMLE indicates there IS audio being input"
How do you know this?
are you "Saving to file"? how is the audio in the saved file?
Adninjastrator

Flash Media Encoder 3 Closes Randomly

Okay, So Everytime I open Flash media Encoder 3, And I Try To Do Somthing (Change Anything, Open Profile, Etc) It Just Randomly Closes. It Doesnt Give me a message or anything. Ive uninstalled and re installed every version of Flash media Encoder at leaste 2 or 3 times for each one. Ive restarted My Computer about 6 times and still it does the same thing every time.
Heres A Video That I Recorded of what happens.
(If Embed Video Doesnt Show Up For You, heres The Direct Link- http://www.youtube.com/watch?v=sKSieFFd08Q )
Please Someone Please Help Me

I think FMLE forum would be best place for posting this query. Link for FMLE forum is :http://forums.adobe.com/community/flash/flash_media_live_encoder?view=discussions

Can any one tell me when i use adobe flash media encoder how can i see my live vidoes on flash media

can any one tell me when i use adobe flash media encoder how can i see my live vidoes on flash media server . thnx

Flash Player version 10.1.102.64 is the last version available to PPC Mac users. However, this Flash version won't work for many videos on Facebook, YouTube and other sites. Adobe's latest version, 10.2.x or later, is only for Intel Macs. Adobe will not provide a newer Flash version for PPC Macs.
The message requesting that you download Adobe Flash Player takes you to Flash Player requiring an Intel processor. Doesn't work on a PowerPC processor. I found a hack, installed it & it works with Firefox, TenFourFox & Safari.
Download this http://www.steelbin.com/FPforFBPPC.zip to your desktop, unzip it, and replace the current Flash Player plug-in which is in your main/Library/Internet Plug-Ins folder, (not the user Library). Save the old one just in case this one doesn't work.
Hack Allows PowerPC Macs to Access Flash 11 Content
http://lowendmac.com/ed/royal/12sr/flash-11-and-powerpc.html
 Cheers, Tom

New Flash Media Encoder

So, I've been playing with the new Flash Media Encoder here:
http://labs.adobe.com/technologies/fme/
It was a really simple download and works seamlessly with
Flash Media Sever. I think you have to update FMS2 to the January
07 update to use it, though. Anyway, below are some options for
trying it out. Have fun :)
Per Chris H from adobe:
1. You don't need a main.asc file on your FMS app to publish
and broadcast live streams with FME.
2. You can get a live stream from FME to playback in the
normal FLVPlayback component that ships with Flash 8 Professional.
Just make sure you have the "isLive" parameter set to true and the
contentPath should be:
rtmp://server_name/app_name/inst_name/stream_name.
Option from FMS livedocs:
1 New Flash Document with two layers: actions and video
display.
2 Add this code from the FMS livedocs to the actions layer:
var my_nc:NetConnection = new NetConnection();
my_nc.connect("rtmp://<YOUR RTMP ADDRESS>/streamtest");
var my_ns:NetStream = new NetStream(my_nc);
my_video.attachVideo(my_ns);
my_ns.play("stream");
3. Open Window > Library > Click little dropdown toggle
next to library title and select a new video display object and
specify actionscript control.
4. Drag Video Display out of the library and give it an
instance name of my_ns and publish it. I used a laptop for this
part so that I could stream to the file from my FMS server. I saved
the .swf as video_receiver.swf.
5 Stop Flash Media Server and create a folder called
streamtest in the FMS Apps folder, then start it again.
6. Fire up FMEncoder, specify the RTMP address you specified
in the Flash 8 AS code, and be sure that the stream is named,
"stream" (no quotes). Also, toggle off the save stream file, unless
you want to save the recording.
7. Click start on FME and open the video_receiver.swf and you
should see the stream playing.
Another idea:
Use the receiver from this tutorial:
http://www.adobe.com/devnet/flashcom/articles/broadcast_receiver.html

We have our own FMS and I have just installed the FME on a
workstation. FME reads video perfect but when I try to connect to
the server it won't accept my username and password. Where do I set
this? I have installed the add-in for FMS and also upgraded to the
latest 2.0.7 release. I'm green to the Flash Media Services so this
may come as a dumb question. Please help!

Flash Media Encoder with multiple cameras?

Hi,
Is it possible to stream 2 or more cameras on one computer
with Flash Media Encoder, or are you restricted to one camera per
machine?
Cheers

Hi,
As JayCharles explained to me, you run two instances of Flash
Media Encoder on the Computer. I was running 1 camera on just one
computer and so used 3 computers instead of using just the one
computer.
In my new case, I had 2 Cameras on the one machine.
When you launch Flash Media Encoder it will detect any
cameras you have on that computer, you will get a dropdown box so
you can choose which camera you want to use in this instance.
Choose the camera you want.
In the FMS URL box type the rtmp path to your Flash Media
server directory you want to stream this video to using either the
ip address or web address of the FMS server followed by the correct
path to where the file will be streamed to for example:
rtmp://192.168.1.10/vob/live
In the Stream Box type the name of the video file without the
.FLV tag, ie:
livevideo
Click the Connect button to connect the Video to the FMS
server.
When ready click the Start Button to start the stream.
So far you are streaming the video, but no one can see it.
Open a Dreamwaver page for example and go to:
Insert/Media/Flash Video (CS3)
or
Insert/Media/FLV (CS4)
Change the Video Type to Streaming Video
In the Server URI box type or paste in the rtmp address you
set:
rtmp://192.168.1.10/vob/live
In the Stream Name Box type in the Stream name you set in
Flash Media Encoder:
livevideo
The Skin type must be HALO, (Dont understand why you get no
choice)
Set the width and height of the Video on the page
Tick the Autoplay to play a pre recorded file, or tick Live
video feed if it is live.
Click ok.
If everything is correct then when you lauch the page the
video feed should be playing.
Lets assume it is, to add a second camera you just repeat the
same steps.
Open another instance of Flash Media Encoder on the Computer
you already have a feed running.
It might complain that the camera is already in use, as it
might try to connect to the same camera on the running application.
Open the Camera source dropdown and now choose the other
camera that should be available.
Put in the same info for the Server URI as you will also
stream to the same folder.
Chnage the Stream name now to:
livevideo2
Click Connect and also Start.
Open the Dreamweaver page you created for the first video.
Follow the same steps as before to create the Video on the
page
changing the name this time to livestream2.
You should now have 2 live video feeds on the same page using
two different cameras.
hope this helps.

Camtasia + Flash Media Encoder 2

I am trying to use the Live Output feature of Camtasia Studio
5 along with Flash Media Encoder (and have also tried On2) to
capture my pc screen. When I try on Live Output on camtasia and set
the framerate to 60 fps and start it up, it actually says in the
recording window: Rate: 60fps (ranges from 55 to 60). However, as
SOON as I open up Flash Media Encoder or On2, they seem to attach
themselves to camtasia and the Rate drops to 4-6fps! I have tried
everything I can think of to prevent this drop but I can't figure
out why FME or On2 are doing this, and the result is very poor
quality videos streamed to my channel at 5fps, when they have the
capability of being sent at 60. Any help on this issue would be
most appreciated. Many thanks,
Dan

I had the same problem and just resolve it a few minutes
ago!!!
ok for example if I need to add a user named "joe" and his
password will be "1234" I will type the following at the momand
promt:
users add -u joe -p 1234
please let me know if it's works

Flash media encoder 3.2 and black magic intesity pro 8.6 drivers

Similar Messages

Maybe you are looking for