Flashed BIOS, ethernet card no longer works
I recently flashed my PT880 Neo to 2.0, but Windows XP would no longer recognize my ethernet card. I tried flashing back to an older version but I am still not having any luck. Anyone have this problem before, or have any suggestions? PS - I correctly flashed the BIOS carefully following the included instructions. Thank you
Clear CMOS Guide
Go back into the bios, restore system defaults, then make your settings, make sure to enable the lan, and then cross your fingers.
Similar Messages
-
IBook Ethernet Network no longer working after upgrade to 10.2
This is really strange but i was using ethernet on os 9 and the dhcp server from my speedtouch router came up and everything worked fine. But yesterday i upgraded to os x 10.2 and the ethernet connection no longer works. I have tried unplugging (this usually works with pc crap) and restarting both the ibook and the router. I know that the router is working fine as i am using the same lead on my powerbook to get internet. Here are the ibook specs:
Indego 366mhz (not firewire model), no airport installed and only has ethernet, usb and modem connections. Any help would be appreciated.1.) Download all OS X 10.2.x updates from software updater.
2.) After all updates are installed, check system profiler to ensure that your network card is detected and operating properly.
3.) Check for updated drivers for your specific network card.
4.) Verfiy and repair permission in OS X, and if possible download Onyx to execute maintenance and cleaning commands.
After all these steps, there should be no more problems.
Good Luck -
ITunes restore iPhone SIM Card no longer works.
Ok, I had all my contacts and information backuped onto my computer so I could easily transfer them from my 16GB 3G to my new 32GB 3GS. After being restored and synced with my computer my SIM Card no longer works. It wont let me place a call or text. When I un-plug the SIM Card and then plug it back in a message comes up saying invalid SIM and then disappears. Also it either has 1 "bar" with the rest flat and no AT&T logo or 3G, or says No Service.
Sounds like you need to call AT&T.
Phil -
Hey everyone I can no longer down load or up date my games videos so on on iTunes
It's telling me I need a new payment method but why would my bank card no longer work how can I fix it so my bank card works againhow do i fix this
-
Iwhy is my sim card no longer working after restoring my 4S
I bought a 4S and had to restore it now my sim card no longer works in my phone. I tried it in another phone and it works so its not the sim card.
I would try two things. First go to the store for your phone carrier and get a new sim card.
If that doesn't work, schedule and appointment with a genius at your closest apple store. -
Hi. Unfortunately my ethernet card was not working anymore. This is the message "This computer does not appear to have any PCI Ethernet card. How can I fix it?
i would try an SMC reset, the following article tells how to do this:
http://support.apple.com/kb/HT3964
if it still gives that message, you need to take it to apple store or apple service provider to have a new card installed. the apple site gives listings of providers and stores in your area:
https://locate.apple.com -
Thunderbolt to Ethernet adaptor no longer works
Hi All,
After upgrading to Maverick I find my Thunderbolt to Ethernet adaptor no longer works. Network app insists the cable isn't connected but the cable works fine with other pcs (a Raspberry Pi for instance). Any suggestions?
R.If you have access to the Companies Intranet then the Ethernet connection is working just fine. The computer is getting a valid IP address from the companies DHCP server.
You need to take this up with the IT staff as it seems whatever IP your computer is getting it is being block from going out to the internet. -
Credit card no longer works error states to contact bank to authorize online purchases. Error occurred following update to IOS 8.
Then you need to contact the bank. Apple does not authorize or not, but the bank would. If a transaction were denied, it would be the bank that denies it, not Apple. Contact the bank and see if there is a problem.
-
Ethernet card no longer showing in ifconfig [solved]
Hey,
Normally I don't have any problems with my networking, but this morning my wireless decided not to work. I haven't made made any changes in the past couple of days, so unsure what has caused it. Last Syu was on Thursday and every day including up until last night was fine.
So spent a while trying stuff out and stressing my tiny little brain for ideas, quick version is I did this:
netcfg: said interface didn't exist.
ifconfig: didn't list the interface (wireless is usually eth1)
lsmod: confirmed the module (ipw2200) was loaded
lspci: confirmed the card was there
After copying the output of the above commands plus the obligatory rc.conf onto usb to move to this machine (and just before pushing <submit> on a much larger post than this :-) I decided to check the mac address listed in ifconfig with what is on the sticker under my machine. Voila! My wireless has actually moved to eth0. OK, that's that solved. (Wish I checked that first though...)
But that means that the reason that my wireless card is now eth0 instead of eth1 is because my old-skool wired ethernet card is no longer there to be numero 0. Why isn't it working? lsmod shows that the tg3 module is loading (it's an Intel card with Broadcom chipset in a Thinkpad T43) , but it no longer shows up in ifconfig. lspci is not showing it (see below), only the wireless card comes up. Does this mean the hardware is borken? What else can I do to check the card?
$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 3 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc M22 [Mobility Radeon X300]
0b:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 8d)
0b:02.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
Appreciate any advice you can give.
Cheers,
vW
Edited subject
Last edited by von_Wanderlust (2009-07-28 16:10:22)Yeah, doesn't give me anything about the ethernet card, but does show the wireless one. No, hang on, just found it. Hmmm, didn't see it before, but I was grepping for 'net' then.
$ dmesg | grep -i eth
eth1: Tigon3 [partno(BCM95751M) rev 4101] (PCI Express) MAC address 00:12:34:56:78:9a
eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
OK, so it is at eth1 now, that makes sense since I put ipw2200 right at the beginning and tg3 right at the end of the MODULES array in rc.conf to avoid the system getting crossed up while trying load them too close together. Thanks B, so at least we know something is happening at boot time.
Btw, my assumption is that ifconfig shows hardware once it is loaded correctly, is that right? But apart from the modules, what else do I need to do to get it showing up in ifconfig? -
Ethernet card doesn't work with new arch install?
Hi guys,
so this is kinda my first post, not that I'm new to arch i just never had an issue i couldn't figure out on my own... But i love arch i have been using it for about a year now and have had no serious problems except for this. I have had arch running on an older dell vostro 200 desktop before i reinstalled with a vary similar issue except that the fix i came up with doesn't work anymore. I will tell you about the first issue first because i ALMOST posted on here about it originally but i figured out a way to make it work even though it was a hassle.
After cold/rebooting my computer the network card doesn't work at all. lspci reported that the kernel module e1000e was the correct one (i have verified this) and that the kernel has loaded it, i verified that with dmesg but still it wouldn't work. After much much anguish and hairpulling, I realized that it had to have something to do with the module so i tried forcing it to reload with rmmod e1000e and modprobe e1000e and it still wouldn't work until i physically unpluged the ethernet cord and pluged it back in until the light on the NIC turned on. After that everything works as normal i could even unplug and plug it back in with no problems. So eventually i wrote a script that did this for me (except for the uplugging and plugging part) and i used that when i cold/rebooted.
But now i have the exact same issue after reinstalling arch to the T except for the fact that the (crazy) fix i came up with doesn't work now. I used my "fix" after booting from the arch cd and it worked just like it always has. And now after rebooting into my fresh system the fix doesn't work anymore. So now i'm back where i was to begin with but i have no idea what to try next. I didn't do anything particularly different during installation except i added a udev rule for the e1000e module just to see if somehow that would fix the problem... it didnt and i have since deleted that (to see if it was the problem). The only other thing that is different is the root and home are now btrfs partitions instead of ext4.
I have booted several other live cds and dvds (diferent distros) including arch derivatives such as manjaro and they all worked just fine, using the same kernel module (e1000e). I'm not sure what that could mean but i know that it means there is a fix for this some way or another. I am going to hook up a wifi adapter and connect that computer to the internet to put some more information up if it's needed (asked for) but for now lspci -vnn | grep -i -A 10 net reports
00:19.0 Ethernet controller [0200]: Intel Corporation 82562V-2 10/100 Network Connection [8086:10c0] (rev 02)
Subsystem: Dell Device 0238
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at fdfc0000 (32-bit non-prefetchable) [size=128k]
Memory at fdfff000 (32-bit non-prefetchable) [size=4k]
I/0 ports at ff00 [size=32]
Capabilities: [c8] Power Management version 2
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [e0] Vendor Specific Information: Len=06 <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
ip a reports:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
3: enp0s25: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:1d:09:8c:36:f6 brd ff:ff:ff:ff:ff:ff
4: wlp0s29f7u3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 64:66:b3:16:92:10 brd ff:ff:ff:ff:ff:ff
inet 172.16.1.55/16 brd 172.16.255.255 scope global wlp0s29f7u3
valid_lft forever preferred_lft forever
inet6 fe80::6666:b3ff:fe16:9210/64 scope link
valid_lft forever preferred_lft forever
lsmod | grep e1000e
e1000e 215644 0
ptp 17692 1 e1000e
any help on what to do next would be greatly appreciated.
Last edited by mvheart/dev/null (2014-08-18 04:02:12)Sorry I was thinking that it was say "state up" after that, I was looking in the wrong place... It's been a long time since I was playing around with this. So it is as i thought it was before?
[aaron@arch-box Arch-Linux]$ sudo systemctl start [email protected]
[sudo] password for aaron:
Job for [email protected] failed. See 'systemctl status [email protected]' and 'journalctl -xn' for details.
[aaron@arch-box Arch-Linux]$ systemctl status -l [email protected]
● [email protected] - dhcpcd on enp0s25
Loaded: loaded (/usr/lib/systemd/system/[email protected]; disabled)
Active: failed (Result: exit-code) since Mon 2014-08-18 11:20:29 EDT; 4min 11s ago
Process: 17650 ExecStart=/usr/bin/dhcpcd -q -w %I (code=exited, status=1/FAILURE)
Aug 18 11:19:59 arch-box dhcpcd[17650]: version 6.4.3 starting
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: adding address fe80::ae3:ee04:7099:77c5
Aug 18 11:19:59 arch-box systemd[1]: Starting dhcpcd on enp0s25...
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: waiting for carrier
Aug 18 11:20:29 arch-box systemd[1]: [email protected]: control process exited, code=exited status=1
Aug 18 11:20:29 arch-box systemd[1]: Failed to start dhcpcd on enp0s25.
Aug 18 11:20:29 arch-box systemd[1]: Unit [email protected] entered failed state.
Last edited by mvheart/dev/null (2014-08-18 15:50:10) -
My Apple TV is a useless brick now. Ethernet port no longer works.
Not sure, but it seems after an update, my ethernet port does not work. I can plug it into the PS3 and works fine. I HAVE TO use WiFi now or my Apple TV is a useless piece of plastic that looks "oh so Apple Cool." Yea, whatever Apple. I have been using this same port for almost 2 years with no issue.
thoughts?It may well be a hardware failure but a few things to try:
Unplug from main for 5-10 mins and restart it.
Reset settings in the Settings menus.
Last resort - try to factory restore to current software using a microUSB cable to hook it up to a computer running iTunes.
Assume you don't have Apple care (even if you did I think it's only 2 years on AppleTVs anyway).
AC -
Right-click Flash selection of webcams no longer works. Bug?
After some tense struggles and several failed webcam swaps, our support team discoverd that using right-click to select a webcam no longer works after our hosted service's recent upgrade. Is this necessary, or a bug?
Yes, the menu driven webcam selection process works fine. It's just the old way to select webcam source that no longer works. The worst part is there's no indication that the selection process that has always worked no longer works. Hence my technican swapping webcams, assuming they aren't working.
-
FW800 and FW sound card no longer working. Mmmmm
My iMac has just stopped working with my firewire Edirol FA66 sound card. It has worked for years but now the iMac refuses to see it. I spoke to Apple Care this morning who ran me through a few things but didn't help. Having said that, my FW800 Sandisk card reader DOES work OK.
To through a spanner in the works, the sound card works fine with my MBP with the same lead and the same 10.8.4 OS.
A second call to AC this afternoon, after checking my MBP worked OK, was a wasted call. Sadly he didn't have a clue and kept pointing me in the direction of divers... for WINDOWS!!!
Anyway, I'm confused.com. Please can anyone help me?JonHob wrote:
My iMac has just stopped working with my firewire Edirol FA66 sound card. It has worked for years but now the iMac refuses to see it. I spoke to Apple Care this morning who ran me through a few things but didn't help. Having said that, my FW800 Sandisk card reader DOES work OK.
To through a spanner in the works, the sound card works fine with my MBP with the same lead and the same 10.8.4 OS.
A second call to AC this afternoon, after checking my MBP worked OK, was a wasted call. Sadly he didn't have a clue and kept pointing me in the direction of divers... for WINDOWS!!!
Anyway, I'm confused.com. Please can anyone help me?
Care to share?
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios. -
[SOLVED] Jmicron ethernet card doesn't work
HI there,
I am installing Arch64 on Sager NP8170 laptop. Networking card is Jmicron PCI Express Gigabit Ethernet Adapter, which is controlled by kernel-build module JME.
Command
lsmod | grep jme
shows that module is loaded. Ping to sites does not work.
dhcpcd eth0
is timed out.
I loaded the latest module from www.jmicron.com. The driver is compiled by the following Makefile:
MODNAME := jme
TEMPFILES := $(MODNAME).o $(MODNAME).mod.c $(MODNAME).mod.o Module.symvers .$(MODNAME).*.cmd .tmp_versions modules.order
EXTRA_CFLAGS += -Wall -O3
#EXTRA_CFLAGS += -DTX_DEBUG
#EXTRA_CFLAGS += -DREG_DEBUG
obj-m := $(MODNAME).o
ifeq (,$(BUILD_KERNEL))
BUILD_KERNEL=$(shell uname -r)
endif
KSRC ?= /lib/modules/$(BUILD_KERNEL)/build
MODULE_INSTALLDIR = /lib/modules/$(BUILD_KERNEL)/kernel/drivers/net
all:
@$(MAKE) -C $(KSRC) SUBDIRS=$(shell pwd) modules
@rm -rf $(TEMPFILES)
checkstack:
$(MAKE) -C $(KSRC) SUBDIRS=$(shell pwd) modules
objdump -d $(obj-m) | perl $(KSRC)/scripts/checkstack.pl i386
@rm -rf $(TEMPFILES)
namespacecheck:
$(MAKE) -C $(KSRC) SUBDIRS=$(shell pwd) modules
perl $(KSRC)/scripts/namespace.pl
@rm -rf $(TEMPFILES)
clean:
@rm -rf $(MODNAME).ko $(TEMPFILES)
install: all
install -c -m 644 *.ko $(MODULE_INSTALLDIR)
/sbin/depmod -ae
When I am doing
make install
I have the following error:
make: *** /lib/modules/2.6.33-ARCH/build : No such file or directory. Stop
I am working with the problem for 2 days and googling does not help either.
Please help.
Last edited by Fixed (2011-05-24 15:45:03)Here are the replies to the commands:
ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:90:F5:B8:10:8A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:31
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
#dmesg | tail -50
usb 1-1: new high speed USB device using ehci_hcd and address 2
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: irq 30 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
firewire_core: created device fw0: GUID ea6410b8f5900058, S400
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
hda_codec: ALC892: BIOS auto-probing.
Too many connections
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
Too many connections
usb 3-1: new high speed USB device using ehci_hcd and address 2
Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04731/0xa40000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 8 ports detected
EXT3-fs (sdb1): using internal journal
usb 3-1.1: new full speed USB device using ehci_hcd and address 3
usb 3-1.5: new full speed USB device using ehci_hcd and address 4
usbcore: registered new interface driver hiddev
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input10
generic-usb 0003:046D:C52B.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input0
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1.1/3-1.1:1.1/input/input11
generic-usb 0003:046D:C52B.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input1
generic-usb 0003:046D:C52B.0003: hiddev1,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input2
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 3-1.6: new high speed USB device using ehci_hcd and address 5
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device BisonCam, NB Pro (5986:0343)
input: BisonCam, NB Pro as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1.6/3-1.6:1.0/input/input12
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
jme 0000:03:00.0: irq 31 for MSI/MSI-X
eth0: Link is down.
usb 3-1.2: new high speed USB device using ehci_hcd and address 6
Initializing USB Mass Storage driver...
scsi6 : usb-storage 3-1.2:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 6:0:0:0: Direct-Access HP v125w PMAP PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: Attached scsi generic sg3 type 0
sd 6:0:0:0: [sdc] 15667200 512-byte logical blocks: (8.02 GB/7.47 GiB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] Attached SCSI removable disk
#ip link
command not found
#lspci -vvv
00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge: Intel Corporation Device 0101 (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f4000000-f60fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4169
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Kernel driver in use: pcieport
Kernel modules: shpchp
00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f650a000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6508000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f6500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000feeff00c Data: 41a9
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6400000-f64fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4171
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f6300000-f63fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4179
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f6200000-f62fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4181
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6100000-f61fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4189
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f6507000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 29
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at f6506000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4191
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f6505000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: nVidia Corporation Device 0dd1 (rev a1) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [size=128]
Expansion ROM at f6000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel modules: nvidiafb
01:00.1 Audio device: nVidia Corporation Device 0be9 (rev a1)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f6080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) (prog-if 30)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150 v1] #18
Kernel driver in use: xhci_hcd
Kernel modules: xhci
03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 31
Region 0: Memory at f6320000 (32-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at d100 [size=128]
Region 3: I/O ports at d000 [size=256]
Region 4: Memory at f6310000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at f6300000 [disabled] [size=64K]
Capabilities: [68] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [40] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [70] MSI: Enable+ Count=1/8 Maskable+ 64bit+
Address: 00000000feeff00c Data: 41b1
Masking: 000000fe Pending: 00000000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
Kernel driver in use: jme
Kernel modules: jme
03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f6326000 (32-bit, non-prefetchable) [size=256]
Capabilities: [a4] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) (prog-if 01)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at f6325000 (32-bit, non-prefetchable) [size=256]
Capabilities: [a4] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fffffffc Data: 0000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f6324000 (32-bit, non-prefetchable) [size=256]
Capabilities: [a4] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fffffffc Data: 0000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
04:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device 9196
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at c000 [size=256]
Region 2: Memory at f6200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
05:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller (rev 30) (prog-if 10 [OHCI])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f6101000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f6100000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fffffffc Data: 0000
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci -
Updated T61p to new BIOS, now Hibernate no longer works
I just updated to the newest T61 BIOS released 1/09, and now I can't hibernate. If I try to initiate hibernation, nothing happens for about 10 minutes, then the popup window comes up, and within another 10 seconds the machine locks up completely.
I've tried to disable hibernation, reboot, CHKDSK with bad sector search (JIC I had a bad block), reboot, defrag, chkdsk again, then reenable hibernation. Checked to find that the hibernate file was contiguous (was), then tried again. Same problem.
It's broke. Sure seems to me that it was caused by the update, since it has worked flawlessly and I typically use the function several times each day.
Help!BIOS updates don't typically cause issues with the hibernation file, nor hard disks to develop bad sectors. you also didn't mention what the operating system is.
my suggestion would be to temporarily disable hibernation, scan for & repair defective sectors, then re-enable hibernation.
disable hibernation:
1. backup/copy your important files first (documents, music, etc)
2. open a command console (see note #2 below how to do that, if necessary)
3. at the command prompt, Enter cd\ (change to root directory)
4. Enter powercfg /hibernate off (disables hibernation)
5. Enter attrib (lists attributes of files in root directory)
6. if 'hiberfil.sys' does not exist, skip to step 8, otherwise proceed to step 7
7. Enter attrib -s -h hiberfil.sys && del /f hiberfil.sys
8. Enter chkntfs /t:10 && chkdsk /r c: (type Y and press Enter when prompted to schedule a scan)
9. Enter exit in the command window and restart windows
- chkdsk will preempt the boot process when the system is restarted
- WAIT for chkdsk to scan & remap defective sectors (this may take a LONG time)
- the system will reboot itself when chkdsk completes
- then log back in to windows
re-enable hibernation:
1. open a command console
2. Enter powercfg /hibernate on && exit
3. done
Notes:
1. 'Enter' means type the command shown and press the Enter key
2. to launch a command console, type CMD in the Start Search box and press Enter when 'cmd' appears under the Programs category. a command console (dos prompt window) should open.
3. for best performance, you might want to do a full disk defragmentation before re-enabling the hibernation file... run defrag c: -f from the command line at least twice (two or more passes may be necessary to do a thorough defrag)
Maybe you are looking for
-
Updated to Oct 2014 version of photoshop CC. since that time cannot save ANY work. I can work on files but when I hit 'save as" every time it says "photoshop has quit working and needs to close." Need solution now.
-
I have an itunes account. However, I need to copy music onto a different iPod than my own. How do I do that? Do I need to create a separate iTunes account for that iPod?
-
I've never used iDVD this way. I imported 115 photos from iphoto, added music, dissolve transitions, and a title page, but when I pressed the icon to make the DVD in received this +WARNING: There were warnings during the project validation. It is rec
-
SQL Server 2005 Workgroup Edition compatibility for SAP B1 2005B
Hi Experts, Please advise SQL Server 2005 Workgroup Edition can be used as the backend for SAP Business One 2005B. Thanks, Shakeel
-
Why the standalone server unable to instantiate a bean?
I am using JDeveloper 11.1.1.2 and working on an application that has dynamic regions. The application was running fine within the Integrated WLS. But I got the following errors when the application run within the standalone WLS 10.3.2: : JspServlet