Flashing Red / Green Sys LED

My Network Extender works off and on. I will have all blue lights, but when I check the NE later I will have a flashing red or green sys light and the other lights will still be blue. I don't know what is causing the issue. I have the GPS module right next to the sliding glass door.

I am having the same problem with a blinking red sys light and red gps light. The system has been working fine for months and without my changing anything at all, it stopped working yesterday. I am using the correct power supply. I have powered off and on the gateway and the extender several times. My zip is 94306 (although Verizon shows my device as nearby Los Altos 94022 where I think the tower might be). I have AT&T Uverse as my ISP with a standard 2wire modem/router gateway 3800HGV-B. My internet speed is 15.39 Mbps down, 1.93 Mbps up (it is speedtest.net not text): http://www.speedtest.net/my-result/3707324666 VoIP test reports 15.1 and 1.92: Speed test statistics --------------------- Download speed: 15132 kbps Upload speed: 1924 kbps Download consistency of service: 93 % Upload consistency of service: 99 % Download test type: socket Upload test type: socket Maximum TCP delay: 54 ms Average download pause: 1 ms Minimum round trip time to server: 24 ms Average round trip time to server: 24 ms Estimated download bandwidth: 15434 kbps Route concurrency: 1.0199696 Download TCP forced idle: 0 % Maximum route speed: 21845 kbps General information ------------------- IP address: 99.108.141.9 Local time: Aug 22, 2014 4:12:39 PM Test server: http://mcssjc.visualware.com/ Thanks for any help, Larry Kaplan

Similar Messages

How can I fix this red blinking SYS LED light?

I am having problems with the extender losing signal and the GPS turns red and the SYS light is slow blinking red. I just spent 40 minutes on the phone with a Verizon tech who had me unplug it and just pretty much said "Sorry, there nothing we can do"!!!! This is happening several times a day for the past 2 weeks.

I am having the same problem with a blinking red sys light and red gps light. The system has been working fine for months and without my changing anything at all, it stopped working yesterday. I am using the correct power supply. I have powered off and on the gateway and the extender several times. My zip is 94306 (although Verizon shows my device as nearby Los Altos 94022 where I think the tower might be). I have AT&T Uverse as my ISP with a standard 2wire modem/router gateway 3800HGV-B. My internet speed is 15.39 Mbps down, 1.93 Mbps up (it is speedtest.net not text): http://www.speedtest.net/my-result/3707324666 VoIP test reports 15.1 and 1.92: Speed test statistics --------------------- Download speed: 15132 kbps Upload speed: 1924 kbps Download consistency of service: 93 % Upload consistency of service: 99 % Download test type: socket Upload test type: socket Maximum TCP delay: 54 ms Average download pause: 1 ms Minimum round trip time to server: 24 ms Average round trip time to server: 24 ms Estimated download bandwidth: 15434 kbps Route concurrency: 1.0199696 Download TCP forced idle: 0 % Maximum route speed: 21845 kbps General information ------------------- IP address: 99.108.141.9 Local time: Aug 22, 2014 4:12:39 PM Test server: http://mcssjc.visualware.com/ Thanks for any help, Larry Kaplan

T61 Battery light flashes red and green

Hello:
My T61(type 8891) won't start. I'm getting a series of flashes from the battery and power lights:
A/C power connected: power light flashes green alternately and battery light flashes green then red/green.
AC off, battery installed: power light flashes green at the same time as the battery light flashes red/green.
This happened twice before in the past 2 weeks. After about an hour, it booted up - no problem. This time, nothing.
Thanks in advance for any assistance.

It started about one month ago - no known cause. The problem happened 3 times since then but each time it booted up by itself after a half hour or so. A new motherboard is going to set me back plenty but f it's needed, I guess I must get it repaired. I'm quite handy at taking the laptop apart. I've replaced the hinge, and bezel.
Maybe the fan is inoperable which may cause it to not boot up. Lately, I've been feeling exhaust air much warmer than before even if it's not being used. I blew the dust off it 3 weeks ago.

My z10 led flashing red when charging and even at battery full it blinks red. no green at any note..

My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me

Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
Red for message or applicaiton notifications.
if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Net extender flashing red or solid green sys light

I just had my net extender activated last week & have several issues:
1) the lights are blue, except the systems light will frequently return to flashing red or a steady green. I have shut down the extender for >30 sec w/o improvement, and I have shut down the router as well w/o success. It tends to interrupt my computer’s internet function when flashing. Any suggestions?
2) I use a sonic net extender from my home’s computer to access my work’s VPN line – is that compatible with the Samsung net extender?
Thx

Hi help101,
Let's explore options to resolve this service issues! Some compatibility issues may certainly exist. You mentioned shutting down your extender for 30 seconds, and our troubleshooting guide indicates to disconnect the power supply from the extender for 30 seconds to reset. Please ensure you do this http://vz.to/y8v847 instead of powering off the unit and test. Keep us posted.
AntonioC_VZW
Follow us on Twitter at www.twitter.com/VZWSupport

Pxi 8360 power led flashes red

I have a PXI 8360 MXI Express board mounted in a PXI 1050 chassis. I am seeing the power LED occasionally flash red and I lose communication with the computer. The power LED will return to solid green status after a few minutes but I am not able to do much with NI DAQ to test the system since it has failed self test. The suspicion here is the power supply may be bad but how do we check that.
The system with the computer has worked well over the past several years and we are concerned about possible damage from a power fluctuation that happened here around Christmas time.

Hi Xavier,
The red flashing light is on the PXI 8360. I have not seen any flashing lights on the chassis.
The modules present in the system are
PXI 8360 MXI Express
PXI 4071 7 1/2 digit flex DMM
PXI 4110 Programmable DC power supply
PXI 4110
PXI 4110
PXI 8252 1394 Host Adapter
TB 2627 multiplexer terminal block
PXI 6289 M series multifunction DAQ
SCXI 1306
SCXI 1303
SCXI 1303
SCXI 1300
So far all testing has been done with all modules installed. Another person has tried reseating all modules to see if that would fix the problem but it does not.
The system will work fine for a few hours and then the blinking LED will begin and somewhere near that time the communications fail with the computer. The light will blink for a few minutes and then will return to solid green. Once the error has occurred it seems that the only way to re establish proper operation is to shut down the whole system, PXI chassis and computer, and restart. I saw one time where the power LED on the 8360 went from flashing red to solid green when the computer was turned off.
The computer is a Dell Precision 690 with PCIe 8361.
I will be opening up the chassis hopefully in the next day or two to check fuses and voltages where I can.
Bill

PXI Chassis Power LED Flashing Red: What to do?

My NI PXI-1042 keeps blinking red the Power LED. I know it means the voltage is out of the specs. What to do?

FilipeTaveiros wrote:
But it is not continuously red.. It is blinking red.. Thanks for your help. Anyone?
This is copied right out of the manual:
The chassis power switch has an integrated LED. This LED indicates one
of three different conditions:
• If the power switch LED is steady green (not flashing), the chassis is
powered on and operating normally.
• If the power switch LED is flashing green, the air-intake temperature
has exceeded the chassis operating range.
• If the power switch LED is flashing red, the power supply outputs are
not within voltage regulation requirements.
You either have a power supply problem, or you are loading it down with too many modules. Try running it empty and see what the light does.
Using LabVIEW: 7.1.1, 8.5.1 & 2013

Dell switch 8024F - Front left LED is flashing red - no connect terminal

Hello,
I have a DELL 8024F switch not connected console me.
The console cable is correct.
The LEDs on the switch are as follows:
LED right power source is green.
Left power source does not exist.
LED fans are green.
Front left LED is flashing red.
What can happen?
I have inserted several SFP + and are led as if they were not inserted.
I get the feeling as if you did not initiate the boot process.
Any suggestions?
regards

Hi,
The blinking LED typical means a non critical error, but if you can’t connect to console and it doesn’t recognize any SFP+ transceivers, it could be a more serious error. If you unplug it and then reconnect power is there any change? Have you reseated the power supply and fan modules?

When I wake up, I have email, but no flashing red LED!

Last night, I plugged the charger into my 8900, saw the clock displayed, and went to sleep. When I woke up this morning, I had 4 new emails and 2 text messages, but the LED was still blinking green, not red. Had I not looked at the 8900's screen, I would not have know there were messages waiting for me.
I searched the forums on this issue, and came across one post which said exiting the bedside mode by bypassing the clock application's "Exit Bedside Mode" option can cause this.
All I can think of, is that I might have set it to Bedside Mode (which turns off the LED) and then pressed the MUTE button to put it in standby. I remember seeing the message dialog box show up saying the phone was entering standby mode, but the message never went away. I cleared the dialog box by pressing the red End Call button. I think the phone may also have exited Bedside Mode at that time, or I may have manually exited it via the clock's option. My guess is that this is what caused the LED not to flash red after receiving messages. Unfortunately, I've been unable to replicate the error using this method, or any combination thereof.
Any ideas?

The blinking red LED blinks ONLY for about 15 minutes after receipt of a message or email. Unless you had received the email and SMS in the 15 minutes prior to your waking, there is no reason your LED should have been blinking.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Any further options for fixing a network extender with flashing red sys light?

I've been using my network extender without any problem for a few years. Well, except it always had stopped working on occasion (maybe every 6 months) and I would have to toggle it back and forth between open access and managed on the Verizon site to get it working. That was fine, but this time it's been stuck on a slowly flashing red sys light. The power, gps, and wan lights are all solid blue. Eventually it will seem to start over with the cycle of leds but end up again at all blue except a slow flashing red sys light.
That was months ago and I've been struggling with it ever since with no luck. I tried calling support a couple of times but could never navigate through to any appropriate option for network extenders. Both times the automated system couldn't figure out what my issue was and hung up on me.
I tried power cycling my cable modem and router. I've tried the open/manage setting change on the My Verizon page for the extender. I've verified my router settings, though no equipment has been changed. I even tried assigning an IP to the network extender and configuring the correct ports for it (found a list of the port numbers somewhere else on this site). I've of course tried leaving it off for a bit.. 5 minutes, 30 minutes, 10 hours, and ultimately a month or so. Nothing makes a difference and I'm still stuck with a slow flashing red sys light. It's frustrating as I general manage only 1 signal bar even at best in the house or around the yard. It's hardly usable even though the Verizon coverage map shows solid coverage all over my house and neighborhood.
Any help or ideas would be appreciated. Did the network extender simply die? Is there any way to diagnose that for certain?

It is up and running again.
I just really wish they would have the courtesy to post on here, Facebook, Twitter, whatever, wherever, but to just let us know that there is a problem, they are aware of it, and are working to fix it.
For a communications company, so far I have not seen that they have any communication skills.

Blackberry Pearl 8100 randomly shuts off and the status LED flashes red

My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
blackberry 8100 v4.2.1.96

Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
So if you're willing to try that, do the following.
First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
http://www.blackberry.com/btsc/KB03485
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

Start up and stuck with the flashing color (red green blue yellow...)

I just bought Macbook pro(My first time with Mac product) today, and when i unbox the MBP it was have a good start everything is ok, than I test the DVD drive to make sure it work or not, than i put the VCD to it. it was stuck (with the flashing color). than i dont'know what to do. I press the shutdown button around 10s the pc is shutdown...I open it again and eject the VCD, than I was stuck with flashing color (red green blue yellow...) i have try to restart many time buy pressing the button but still the same. than i keep it away for about 1hour than I open it again It was WORKING AGAIN the same as I first started, than I restart, but the same problem happen again (flashing color (red green blue yellow...).
1. I have tried to boot from DVD that come with the MBP holding C but nothing happen
2. I have tried to reset PRAM (Command-Option-P-R) not work
So what wrong with that?
Could anyone help me to fix this out?
Thank you

Solida wrote:
the flashing is the Macbook pro screen it Flashing Loop, sometime red, than suddenly change to green than yellow than loop again and again.
Notice when it first start up I see APPLE LOGO than the waiting animation round. than the random screen flashing color is happened.
Three options:
1. Call AppleCare.
2. Go to an Apple Store.
3. Go to an Apple Authorized Service Provider (AASP)

Blackberry LED light keeps flashing red

Yesterday Vodacom Care gave me a new Q5 device - i had a Q5 for 2 months and the phone just went dead - so they replaced it . Now my Q5 LED light keeps flashing red and it's a NEW PHONE ??? - make it stop please !

Hello,
Welcome to the BlackBerry Support Community Forums.
Thanks for the question.
Follow the steps below to try and bring the BlackBerry Q5 back to life:
Ensure that BlackBerry Link is installed on the PC or Mac OS
Ensure the computer has an internet connection.
Launch the BlackBerry Link Software.
Note: A backup of the BlackBerry device should be tried before a reload.
Turn off the BlackBerry device. Make sure there are no flashing LEDs and that the LCD is not still being lit by the backlight. If there are any flashing LEDs, hold the power button for 15 seconds until the LEDs stop.
Connect the BlackBerry device to the computer.
When prompted with Cannot communicate with device, click Restore and then click yes allow the update to be downloaded and installed on the BlackBerry device.
If the restore button is not seen press the vertical dots in the lower right corner of BlackBerry Link and select disconnected device. Highlight the disconnected device you are working with and attempt steps 4 to 6 again.
If the issue still persists, then I suggest contacting your network service provider for repair options.
Let me know if you have any more questions.
Cheers.
VIA | ViciousFerret
http://supportforums.blackberry.com/t5/BlackBerry-Z10/BB-Z10-Died/m-p/2230087#M10125
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

Why did mine stop working a few months ago? The Sys Light flashes red constantly - even after hours of being powered up.

I bought this last year - early summer. It worked great at first.
Sometime during the winter it stopped working with a constantly flashing red Sys light. I have tried many times to start it up, same issue even when leaving it powered up for hours. What is my next step in trouble shooting this issue?

Call Verizon Wireless Customer Service at (800) 922-0204 and verify the device is registered and working properly from there end. Good luck!

Z10 - blank screen + led flashing red

On connecting my new Z10 with BBlink, was given a an option for available upgrades. On upgrading the screen went blank and LED flashes red - 3 short 2 long - blank and starts the sequence again. Am unable to restore, restart or anything. Help wanted please email.
Solved!
Go to Solution.

Glad, that you were able to resolve the problem, Hopefully future releases of the BB link would work better with Mac's..

Flashing Red / Green Sys LED

Similar Messages

Maybe you are looking for