Flashing red tape on DVD

I have a problem where there is a flashing red clip emblem in the middle of the frame for about two minutes at the start on a dvd. The clip is about 40 minutes total and I need to see if I can take this flashing emblem out. Since it is burned to the dvd and it is mpeg 2 is there anyway to take it out using final cut pro or some other program? I also have CatDV pro. Any ideas would be appreciated.
Mark

I assume this red emblem is over a live background, right?
If you were to try retouching this in Photoshop or even a proper rotoscoping application, that's around 3600 frames for two minutes. Multiply that by how many minutes you need for a single frame and factor in your hourly rate...
Not saying it can't be done, but who is going to pay for it and how much is your sanity worth?

Similar Messages

  • Convert VHS tape to DVD or flash drive

    I would like to convert home movies that are on a VHS tape to DVD, and then to a flash drive or USB stick

    convert a vhs tape to digital
    I have done lots of that.
    To get your VHS video into iMovie, use the Grassvalley ADVC300 (much better than the roxio easy vhs to dvd).  With the ADVC300 Audio and Video go in, FireWire comes out. It also comes with a nice Macintosh application that works flawlessly with iMovie 06 and iDVD 09/11 (I have used it a few times with iMovie 11).
    The program that comes with the ADVC300 has some nice filters that can improve video and audio of the source material. The ADVC300 will take Audio and Video from any source (VCR, Tivo, Satellite Receiver) and convert it to FireWire (iMovie will treat it like a camera).
    http://www.grassvalley.com/products/advc300
    I would use iMovie 06 with iDVD 09/11, why?
    iMovie 09/11 uses 'single field processing' meaning every other horizontal line of the video is thrown out, which reduces the sharpness of the footage. iMovie 06 uses ALL of the image to form the video.
    If your primary workflow is editing DV clips and making DVDs, iMovie '06 is better suited. Your movie will arrive at iDVD in DV format, which is an ideal match for making a DVD: same resolution, same pixels aspect ratio, and original quality.
    If you share your movie from iMovie 09/11, it gets re-rendered at 640x480 or less, and then iDVD upscales it back to 720x480. The end result is obviously not as good.
    iMovie 06 and iDVD 11 is a "lossless" combination.

  • Help: Convert 8mm tape to dvd and edit with imovie

    Please help. I would like to convert my 8 mm tapes to dvd and edit them using imovie. I have the original camcorder that captured the video and it still works. (The camcorder is a Fisher Camcorder-8 model FVC-801 circa 1987). It says digital on the camera so I think the videos may already be in some sort of digital. I also have a new macbook and it only has usb ports not firewire. To play the video on the tv the camera came with a RF Adaptor and all i do is plug the adaptor into the camera and the yellow, red, and white cords into the tv. I have done a bunch of research and it seems that I will need some sort of converter. Can someone please tell me what kind of convert, which brand I should buy, and how the process works (ie what gets plugged into what, etc) Thank You.

    If you want to edit the footage, I'd recommend to NOT put them on DVD first. That will only compress the footage heavily ... then you'll have to uncompress to convert them into a format that iMovie works with natively.
    Instead, capture the footage by playing through a qualified DV device (DV camcorder, VTR or converter) and capture directly into iMovie for editing.
    Once you're done with the edit, that's when you'd export for DVD for final delivery.
    -DH

  • DVR620 won't dub from tape to dvd

    We bought at DVR620 over a year ago with the express purpose of recording old tapes to dvd.  The several times since then we've tried to do this and been unsuccessful. First, you press the setup menu, go to General Setting, press enter and NOTHING happens.  You can't enter diddly squat.  Oh, I know my remote works since I can use the up and down arrows on it to move vrom General Setting to Timer Programming, etc. but you can't enter any of these selections. I've tried puttting in a blank dvd-r, pressing dubbing with a tape in it, we get a red circle with a line through it.  I've done this in dvd and vcr mode with the tape playing and paused both.  This does not work. I've pressed the record button, put the tape in, pressed pause once it's started playing.  This did not work.  I've had the tape and dvd in both, pressed record, pressed play then pause on the vcr and nothing happens.  I do have several messed up dvds though. I did notice that if I press dubbing with the record slot taped over on the tape it instantly starts trying to record from the dvd to the tape though.  This has put blank spots on a tape now.  I have found no way to change the dubbing mode from dvd->tape to tape->dvd. At this point, I'm very frustrated.  Something's not right with this unit or the instructions are simply wrong or both.  Any help appreciated. 

    Be sure you have no DVD inserted, and no VHS tape inserted. Although this shouldn't matter, as long as you're not recording or playing back, let's be sure none are even inserted. When you press SETUP on the remote, and the Setup menu appears, you see General Setting, Timer Programming, Title List, and DVD Menu. You should see that Title List is in light blue and is therefore "grayed out" so it can't be selected. When you press the down arrow on the remote to move to Timer Programming, do you see that General Setting is also grayed out? If it is, that is the reason you can't press enter and then get the General Setting submenu. If the General Setting text is white, you should be able to press ENTER or the right arrow to go to the General Setting submenu. The changing of DVD->VCR to VCR->DVD dubbing mode is done by General Setting->Recording->Dubbing Mode and then selecting VCR->DVD. If General Setting is grayed out, such that it can't be selected, and you have no DVD and no VHS inserted in the DVR620, I'm not sure why that would be. In that case, you can try unplugging it for about 30 minutes and then plugging it back in to see if it resets itself. I have tested this with my DVR620 and only when the DVD or VHS is playing do I get the red circle when I press SETUP. I don't see the Setup menu at all in that case.

  • How do I restore my Ipad 4 from my desktop computer? My charger was broken. I bought a new one but now it won't charge. I have a BATTERY bar in the middle of the screen that is flashing RED and I have a symbol on the bottom that looks like a charger.

    How do I restore my Ipad 4 from my desktop computer? My charger was damaged so I bought a new one but it won't charge. On my Ipad, I have a BATTERY bar in the middle that is flashing RED and an icon on the bottom that looks like the end of a charger. I have tried to force into reset mode, by holding the sleep key and home button SEVERAL times but it does NOT work. I have plugged my Ipad into my desktop computer, but I do not have a screen on my desktop that is coming up. THIS HAPPENED BEFORE AFTER I DID AN UPDATE AND WAS LOCKED OUT AND I USED EITHER ICLOUD OR ITUNES TO RESTORE, NOT SURE WHICH AND I FORGOT HOW.

    Hi MrsMoosie,
    I'm sorry to hear you are having these issues with your iPad. If your iPad isn't responding or doesn't appear to be charging, you may find the information and troubleshooting steps outlined in the following articles helpful, in particular the following portion:
    If you don't see the charging screen within an hour, or you see the connect to power screen, check your connector, USB cable, and power adapter. Make sure that everything is plugged in firmly, free of debris, and not damaged. You might want to try a different USB cable or power adapter.
    If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
    If you can’t charge your iPhone, iPad, or iPod touch - Apple Support
    Regards,
    - Brenden

  • My iPod Shuffle (4th Generation) flashes red when I put it in the USB drive. What is wrong and how do I fix it?

    Earlier today, I tried to use my shuffle, but for some reason, not only did it not play music, it gave a tri-tone. When I put it into the USB of my computer, the light flashed red for a moment then stopped. My iPod does not show up on iTunes nor My Computer. Can someone tell me what is wrong and how to fix this?

    Kathleen,
    Start with this Apple support document.
    http://support.apple.com/kb/TS1410
    B-rock

  • Screen is suddenly flashing red and purple, whats up?

    screen is suddenly flashing red and purple, whats up?

    Octopus Chef-
    I think you will need the services of an iPad repair center.  If you search for an independent iPad repair center, the cost of a non-warranty repair should be less than at the Apple Authorized Repair Centers.
    One thing you can try is to reset (reboot) your iPad.  Hold both the Home and Sleep buttons for several seconds until the Apple logo appears.  Ignore the "Slide to power off" arrow.  The iPad will restart after a couple of minutes.  Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
    Fred

  • My Curve won't turn on and no sign of flashing red light

    Hi!
    I m all new to this blackberry forum thing....anyway i have a blackberry curve and all of a sudden yesterday it just stopped working. when i looked at the phone the screen was all white so i took out the battery and put it back on thinking that it will come back up but it didnt. Then i took the battery out again and plugged it to the USB(without the battery) because ususally it comes back up, but it still didnt. i put the battery again and plugged it to the USB thinking that it needs to charge but still no since of that flashing red light. I took the battery out and put my friends battery (cos he has a curve too) but still it didnt work. I did try holding down the power (red)button still not back on. 
    I just dont understand whats wrong with it, its not like i dropped it in the water or dropped it on the floor. I didnt do anything to it. It just stopped working. 
    Im really frustrated right now...I just dont know what to do..i hope someone can help me
    THanks!

    I finally got my curve to work.  I just left it on the charger for a while and then it powered up. It seems if its a little low on power and I don't charge it relatively soon it shuts down and won't power up for awhile. I've also updated the software and cleaned out the junk files. It seems to be working fine now, go figure.
    tm

  • IPOD - flashing red in itunes won't read or write

    I seem to be having a major problem. After updating to 10.4.2 the ipod was sluggish when adding songs. My Ipod was wiped clean in itunes 5 then I had a folder with an exclamation point - followed all the advice reformatted etc. I was able to load 3 songs - 1 at a time after shut down. Now when Itunes opens the ipod is flashing red and then I get the message - can't read from or write too. What do I do?? I reformatted 3-5 time, changed fire wire ports shut down etc - still no luck.

    I am not sure this will fix it, but you mentioned a photo editing program had been installed. If that was due to a new digital camera, you might try changing the drive letter assigned to the ipod. Some digital cameras and photo frames seem to "take over" certain drive letters (typically E,F,or G).
    Try changing the ipod drive letter to something further down the alphabet, like M. Directions are at the end of this article:
    http://support.apple.com/kb/TS1493

  • Flashing red Light on Photosmart D5160

    I have a 3-4 year old Photosmart which know suddenly comes with flashing red light when i try to print.
    In the display it says ERR and there are two commas or something on the bottom right. It does not match any of the problems which i can find on hp's pages.
    I received an error message on my computer when trying to print - saying something like : do not recognize usb (code 043) Port_#003 Hub_#0003.
    Can anyone help me out?
    espen

    Hi,
    Flashing amber LED does not always point to fault. Please see this bug related to system
    LED flashing amber.
    CSCsh44884 Bug Details : Appliance: No Troubleshooting for System health LED
    Status: NEW
    Symptom: The appliance hardware has a "System health LED" that may go into amber status,
    to indicate a hardware warning, and red to indicate a hardware failure.
    Conditions:
    In most situation the ACS appliance is still operative, when the light is in amber status.
    The appliance should offer better information on what condition caused this alarm, and include this either by new CLI command, or included as additional information in pakage.cab file.
    .Workaround:
    -Reload appliance
    -Verify enviromental conditions (temperature, power)
    Alternate Details:
    Symptom:
    The appliance hardware has a "System health LED" that may go into amber status, to
    indicate a hardware warning, and red to indicate a hardware failure
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&b
    ugId=CSCsh44884
    Let me know if you have any question.
    Regards,
    ~JG
    Do rate helpful posts

  • Bold 9930 - dead and flashing red light

    Bold - Verizon 9930, died with flashing red light, non-responsive. Can connect wtih loader, re-loading latest OS for Verizon (7.1.0_rel1737_PL5.1.0.429_A7.1.0.580_Verizon_Wireless) Load fails with "application loader was unable to connect with your device" when it tries to connect with the JVM. I have tried:- fully charged known good battery (tested in another 9930)- wiping device- start without battery, insert battery when JVM message comes up- both BB desktop and Loader directly- two different PCs (no change)- different USB ports- older version of BB OS for device- many, many iterations... All end with "application loader was unable to connect with your device" Is the device scrap?  If so why?  It's not even 2 years old, out of warranty, and apparently now totally worthless.  This one is the CEO's Blackberry, and he's not happy...  If I can't resolve this, it will be the very last BB to ever see the inside of our company.  This is the second 9930 to die this way in the last 4 weeks.    

    Hello,
    Firstly...
    truckin-on wrote:
    Does RIM care about these failure issues at all I wonder?
    If you were hoping for a response from RIM, you have misunderstood the purpose of these forums. These are not a channel for any communications with, support from, nor escalation to RIM for anything. Rather, these are a user-to-user community of volunteers trying to help each other out amidst their own busy lives. So patience perhaps would be a good thing to have...
    Nevertheless, please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
    With the battery inside, connect your BB to the wall charger
    Leave it alone for 2 hours, no matter what the LED or the display does
    Remove the battery
    Wait 15 minutes
    Insert the battery
    Wait another 2 hours, no matter what the LED or the display does
    This has been known to "kick start" some BBs.
    While you've already validated that your battery is good, I don't think you've tried the first part of this test:
    Obtain a known good and already fully charged additional battery...use it in your BB and see what happens
    Obtain access to a known good and identical BB...use your battery in it and see what happens
    The results of this will indicate if it's your BB or your battery that has the problem.
    While perhaps redundant to what you've already attempted, here are a few more things to try:
    KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
    KB27956 How to recover a BlackBerry smartphone from any state
    http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
    Since you are out of warranty, your next step I suppose would be to seek in-hand support from a qualified technician to give you a proper diagnosis. Doing such at this internet distance is quite a challenge and therefore cannot replace in-hand evaluation and diagnosis.
    Good luck and let us know!

  • Flashing red light on my ACS 4.1

    Hello, I have a flashing red light on my ACS. I have searched on Cisco.com to see what this meant and how I can fix it. I am aware that it is a critical error on the system health for my ACS. But what exactly does that mean? How can I figure out what is the problem before it becomes a big issue. Any help is well appreciated! Thanks!!

    Hi,
    Flashing amber LED does not always point to fault. Please see this bug related to system
    LED flashing amber.
    CSCsh44884 Bug Details : Appliance: No Troubleshooting for System health LED
    Status: NEW
    Symptom: The appliance hardware has a "System health LED" that may go into amber status,
    to indicate a hardware warning, and red to indicate a hardware failure.
    Conditions:
    In most situation the ACS appliance is still operative, when the light is in amber status.
    The appliance should offer better information on what condition caused this alarm, and include this either by new CLI command, or included as additional information in pakage.cab file.
    .Workaround:
    -Reload appliance
    -Verify enviromental conditions (temperature, power)
    Alternate Details:
    Symptom:
    The appliance hardware has a "System health LED" that may go into amber status, to
    indicate a hardware warning, and red to indicate a hardware failure
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&b
    ugId=CSCsh44884
    Let me know if you have any question.
    Regards,
    ~JG
    Do rate helpful posts

  • My z10 led flashing red when charging and even at battery full it blinks red. no green at any note..

    My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me

    Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
    Red for message or applicaiton notifications.
    if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Net extender flashing red or solid green sys light

    I just had my net extender activated last week & have several issues:
    1) the lights are blue, except the systems light will frequently return to flashing red or a steady green. I have shut down the extender for >30 sec w/o improvement, and I have shut down the router as well w/o success. It tends to interrupt my computer’s internet function when flashing. Any suggestions?
    2) I use a sonic net extender from my home’s computer to access my work’s VPN line – is that compatible with the Samsung net extender?
    Thx

        Hi help101,
    Let's explore options to resolve this service issues! Some compatibility issues may certainly exist. You mentioned shutting down your extender for 30 seconds, and our troubleshooting guide indicates to disconnect the power supply from the extender for 30 seconds to reset. Please ensure you do this http://vz.to/y8v847 instead of powering off the unit and test. Keep us posted.
    AntonioC_VZW
    Follow us on Twitter at www.twitter.com/VZWSupport

  • Why is my network extender flashing red and pink?

    hi,
    I have had my Verizon extender for a while, I bought a new Motorola modem/router connected them up and now my network extender isn't blue like it was before.
    the system band is flashing red and the gps band is solid pink.
    I have unplugged it more than once and it still won't go back to blue!
    Any help please?
    thanks
    Karen

    The breakpoint may not be as expected..
    OPen the subVI and check to see if there is a red contour when it is not running.
    If it is the case, use the brakepoint (pointer) and click onto a blank area inside the block diagram of the subVI. The red contour should dissappear.
    Run the vi (main vi). See if it is okay.

Maybe you are looking for