Flex 2-15: How to access BIOS

I purchased a new Flex 2-15 online the past week. The model name shown on the back is "20405". Manufacture date is May 12, 2014. The User Guide refers to a "Novo Button", which is shown in diagrams as being on both the left edge and the right edge near the front. Neither location has a button of any sort. The right edge has a pinhole in the supposed button location. A curved arrow icon is next to the pinhole. I have an inkling this may be some sort of factory reset button. Lacking the Novo button, what is the procedure for accessing the features which the manual says are accessed by pressing this non-existent button?. That is, BIOS, and/or the one touch image backup/restore system?
Moderator comment: Subject edited to match content.

That is correct. At that position, my Flex has a pinhole roughly big enough for paper-clip wire. Many electronic devices (including some computers) use pinholes like that for hard reset purposes. The "Safety, Warranty, and Setup Guide" foldout that was in the box with the laptop shows a "Novo button" at the same two locations as the User Guide. (The diagram is labeled Port assignment and button layout) One button is shown on the right edge at the left of the memory card slot (as on the UG page you refer to), the other on the opposite edge, just right of the audio jack. At both of those locations, my computer has solid plastic except for the pinhole at position #1 in the UG page 15. This image may help:

Similar Messages

How to access BIOS on Lenovo IdeaTab Lynx?

I am curious how do I get into bios on my Lenovo IdeaTab Lynx tablet?
Ps. It does not have a keyboard.

Dear dc2000
Welcome in lenovo forums
to access the bios just hold on the Volume Up+Down and power button
Please let me know
Thanks
Alaa
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to access BIOS on Satellite L670-134

Hi there,
i need to access the BIOS but i dont know the key combination.
Tried F1 F2 DEL Backspace etc none worked.
I think i turned an option like fast boot on once before... when i turn on the laptop i cant see any postscreen, the screen stays black after turning the laptop on and then the windows logo appears.
So how do i access the BIOS!?

Hi buddy,
If you enable this fast boot option you must be very quick to enter the BIOS so press F2 key immediately after you turned on your notebook.
Alternative you can access the BIOS using preinstalled Toshiba HWsetup. The fast boot option you can also disable/enable with this tool as far as I know.

How to access BIOS settings in Bootcamp Windows 7?

I need to reset the BIOS boot order in my Bootcamp partition to boot first from a DVD/CD, such as a Windows 7 repair disk. What are the steps to get there?

There is no BIOS, so you can't access the settings.

Portege Z930 15X - How to access BIOS?

HI all, I've got a Toshiba *Z930-15X*, and I can't access the BIOS at all.
I want to downgrade to W7, and it used to be pretty easy before Windows 8.
I know I have to follow these steps , and I would gladly, except I can't access this *** BIOS. I tried all the F1-F12 keys.
Does someone has this model and can tell me exactly which keys work, or another way to access the BIOS?
Thanks in advance!

Many people with new Win8 machines have asked the same question. Win8 is designed to have faster start as old Windows operating systems. For me it is something like standby option.
What you must do is to shut down Windows completely. After doing this you will be able to enter BIOS settings. Just follow link posted by PauPau and change settings in power options.
On my machine I must press F12 and there is option to enter setup settings BIOS settings.

Tecra 740 cdt - how do I access BIOS ?

Hello,
I've got an old Tecra 740 cdt without disc drive and an empty hard disc.
I wonder how to access BIOS so I could change boot priority to boot from an bootable CD.
Browsing this forum I found some keystrokes like F2, F8 and so on but this didn't work for me.
Anyone can help ?
TIA

Hello
The best page with information about Tecra 740CDT is http://www.toshiba-europe.com/bv/computers/products/notebooks/tecra740cdt/index.shtm
Check the content of Options & Accessories.

Accessing BIOS on the DV6

I want to be able to access the Bios so that I can change my AMD 7xxxm series GPU to be the 'fixed' GPU so that the Intel HD 3000 is no longer used. I read that this can be changed in the BIOS, but when I restart my computer, there is no information on how to access BIOS, just a blank screen with a HP logo at the centre. I've tried the traditional F1, F10 and escape with none going to BIOS. Is there any way of accessing BIOS without having to take the PC apart? I've spent hours already trying to resolve this issue, and don't wish to take the computer apart.
This question was solved.
View Solution.

Tap the esc key continuesly afrer presing the power button, then f10.
Refer:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02693833
Wish you luck,
Karthik
--Say "Thanks" by clicking the Kudos (purple thumbs up icon in the lower right corner of a post)
--Please mark the post that solves your problem as "Accepted Solution"

Memory Problem on 790fx-gd70 - how to access DDR Voltage in BIOS?

I have been getting memory related problems on a 6 month old system. I could only boot from one stick of RAM (Corsair TW3X4G1333C9A) but even then system was not stable for gameplay or stability test though this stick did pass overnight memtest. I returned the board, cpu and memory for them to test. They diagnosed faulty RAM and replaced. Well it worked OK for 24 hours then I started getting BSOD "PFN_List_Corrupt" and "Memory_Management" crashes.
I tested the new sticks and one fails memtest after a few seconds with 2378 errors and the other, although it passes memtest with 20 passes, crashes out straight away on Prime95 Blend Test (i.e. the one that stresses RAM).
They suggested I enter DDR Voltage manually rather than relying on Auto but no matter what I seem to enable this option is greyed out. Does anyone know which settings need changing from defaults so I can get at the voltage section?
I have tried swapping around the dimms but they are all the same regardless so not a slot problem. Now of course, I don't see it as a RAM problem either unless I am the unluckiest person to keep getting bad sticks. So now I think maybe something on the board or CPU is causing damage to the RAM or at least causing it to mis-report. Could a fault in the memory controller be doing this and if so how can I test for this?
At my wit's end here. Hope someone has some ideas - either on how to access DDR Voltage in the BIOS or get to the cause of my problem.
Many thanks.

OK thanks for explaining a bit more . This power unit did get some very good reviews in the sub $100 from many sites and from these I thought it would suit my needs. I have arranged to try a friend's 650w next week.
I think I am maybe not being clear. I have had the system running OK for six months. I had had no need to test the ram and didn't bother with stability tests at that stage. I am not a gamer and use my machine more for video and graphics work. One thing I did notice from the start was the couple of games I do have on (Call of Duty and Fallout3) would give occasional freezes. I put it down to my now rather old hot GPU which I would get around to replacing in due course.
Now the real problems started recently when I got round to replacing the stock cooler with a Titan Fenrir. Trouble with this is it overhangs Dimm1 but in moving around the memory sticks I seem to have opened a real can of worms. I could only get it to boot from one of the sticks. This stick passed memtest but would crash out of prime95 and games would freeze within a couple of minutes.
Now, the retailers here in the UK told me to send back board, cpu and RAM. They tested all 3 but they only replaced the memory and as you can see from my first post the memory related problems have continued. The memory by the way is in Corsair's list as "100% tested compatibility". Is it possible that something about the CPU/Board that is damaging the RAM? If a stick is failing memtest (it failed another test too called Windiag) is that definitive? It is bad for sure or board/cpu misreporting? Am I right in thinking memtest86 does cannot distinguish faulty RAM from faulty memory controller? Is there a test I can do to check if the CPU alone is faulty?
I don't know if this means anything to you guys but when I ran the prime95 (Blend) recently with both sticks in it failed straight away on 2 cores but went on running on the other 2.
One of my other frustrations is I don't know anyone else with am3 board or memory so swap things around.
Any suggestions for pinning this down would be much appreciated. Just don't assume my knowledge is as great as yours . But I do learn. I never knew v x a=w for example. And I now know how to change DDR Voltage in the BIOS - I had been expecting a sub-menu where Auto was greyed out and in fact it was just sitting there waiting for me to press + and -. Very embarassing that I spent hours trying to change this when the instructions on what to do were right there in the help column!

How to access internal table data from webdynpro to Flex application.

Hi Connoisseur
The data transfer from Abap WebDeypro to flex island works well. I followed , there is an example from Thomas Jung (by the way as always Great Work) and Karthikeyan Venkatesan (Infosys) but this example covers simple type only.
There is no example with complex types like arrayCollection which handle the transfer of data from flex to WebDynpro.
i tried to do pass internal table value to flex-datagrid.but its not work.
i would like to know
1.how to access internal table data from webdynpro to Flex application.
2.how to pass the internal table to flex-datagrid.
2.how to pass dynamically in ADOBE flex.
3. how to do Flex is receiving the wd context data?
4. how can we update WD context with FLEX data.
Ple give me sample example and step by step procedure.
Regards
laxmikanth

Hi Laxmikanth,
Please refer this...
Flash island: update complex type from flex
Cheers..
kris.

How to access the BIOS setting for H330 to verify VT setting?

How to access the BIOS setting for H330 to verify VT setting?

Hello Rho2019 and welcome to community,
To enter into BIOS, Press and hold the F1 key then turn on the computer. When you hear multiple beeps, release the F1 key.
Best Regards,
Tanuj
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to access Flex builder application on VC??

Hi,
I have developed an Flex application using Flex Builder 2.0.1 & i want to access this application on VC how to do that??
Is there any other way accessing flex application on SAP portal???
I want to know whether It is possible or not?? if possible how to do that??
please help me if anyone knows about this isssue.
Thanks in advance.
Regards,
Malar

Double post, look at this How to access Flex builder application on VC??
Best Regards,
Marcel

How do you access bios at start up p875s7102

I want to test my USB recovery flash drive but can't access bios at start up can someone please help also how do you boot from the read only file on the hard drive on my old model you would push 0 and hold while powering up and the computer would return to the just out of the box state THANKS

How would I get into bios if I can't remember my password to get to the desktop though to start with? I am beyond annoyed with windows 8 and toshiba. Best Buy didn't give me a disk, instead there's a stupid card. If I had the disk, I could simply do a reinstall and change the password. Plus we pay for the operating system so this is not good, what they are doing at all now! Even if they gave a reset disk it would be helpful. But now they want to charge for that?
any way.. how do i get to the bios at bootup before reaching the desk top so that I can reinstall or "something".. must be able to in there!

How do I access bios for my Satellite L45 - S4687?

I can't seem find info on how to access my bios anywhere. If someone can help I'd greatly appreciate it!

Satellite L45-S4687
Maybe this helps.
BIOS Setup / BIOS settings -- access instructions
-Jerry

How to access a Access array in flex

Hi
      Guys can any body explain me how to access an array.Actually i am succsufully getting value from array named Dynamic array.
                   DynamicArray[i].language_1[0].translation;
here the node language_1 is not static it may be language_2 or language_3 or language_4 ect.. so i put that getting value in a variable named key
var key:String = 'language_1'; //Suppose i am getting right value here in key
So please guide me how i access my dynamic array using key so that i got same value as previous code give.
i already tried:-DynamicArray[i].key.translation;
                       DynamicArray[i][key].translation;
but every time got error.
for more clarity i put array structure here
DynamicArr= Array (@43b1271)
    [0] = Object (@43ad219)
        contentlanguage_1 = Array (@43b1431)
            [0] = Object (@4417a11)
                choice_id = "0"
                deleted = "N"
                downloadurl = "http://94.126.48.105:80/cgi-bin/WebObjects/DataVit.woa/wa/Download/getImage?imageId=1281&f ilename="
                selected = "Y"
                translation = "2_486"
            length = 1
    [1] = Object (@4417949)
please Help me out
Thanks In Advance
   Vineet Osho

Hi Vineet Osho,
You haven't tried ---> DynamicArray[i][key][0].translation; This will work
You tried -> DynamicArray[i][key].translation; (This is wrong as you havent specified on which index you want to access)
If still doesn't work ty this...
Try (DynamicArray[i])[key][0].translation;
If the above one doesn't work then try the below one...
var obj:Object = DynamicArray[i];
var translation:String = obj[key][0].translation;
Thanks,
Bhasker

Yoga 3 Pro - Accessing BIOS, boot menu and System Recovery

The following tutorial will explain the following topics
How to access the BIOS Setup
Choosing a boot menu
Start a system recovery
It is not the idea to explain every single option of the above, since many of them are complex and it would be too extensive for such a tutorial like this.
To execute any of the tasks above you need to press the button marked with the red arrow in the picture below:
Press the button when the Y3P is off! Use a small pointing device, I use the tablet pen of one of my Thinkpad tablets
Once you press the button you will be presented with the following screen:
Use the cursor keys to move up and down, press Enter to choose an option.
1) BIOS Setup
The BIOS is where you can get technical information about your device, as well to change boot parameters and setting up security passwords. Be very careful when changing certain values, since it can affect the way the Y3P works and/or affect performance and security settings.
Information Screen
It gives the hardware details of the Y3P, like CPU, installed RAM, SSD capacity and so on. This is a display only screen, no settings can be changed here:
Configuration Screen
Time and date can be changed in this screen. Furthermore to deactivate the Wireless LAN and enable the Intel Virtual Technology. If you plan to use Virtual Machine software in your Y3P this setting must be enabled
Passwords can be set up in this section. Secure Boot settings can be changed here.
Primarily designed to protect users from rootkits and other malware attacks by blocking unauthorized executables and drivers from being loaded during the boot process, it must be deactivated if you plan to install Linux or having paralel operating systems
Boot Screen
Boot modes can be selected in this screen, you can disable booting from a USB stick or from a network for example
2) Boot Menu
This option is useful if you have Linux installed (using managers like LILO, GRUB, etc).
If you only use Win8 or higher there 's no much you can change.
3) System Recovery
This option will allow you to restore the system to either its factory setup, or to a previous backup done within Windows
A factory set up will leave the Y3P as it was shipped from Lenovo your private data and installed apps and/or programs will be wiped out. So make sure you have an external backup before such a reset

OK article. Doesn't answer my questions.

Flex 2-15: How to access BIOS

Similar Messages

Maybe you are looking for