Flush headphones?

What does that mean?

This means that there will no longer be an indented headphone jack. This was so one must purchase iPhone headphones (or an adapter) because most headphones did not fit inside the collar. Flush means the headphones just plug down flush with the top of the phone.

Similar Messages

  • Flush headphone jack?

    Does anybody know if the new 3G has a flush headphone jack?

    It means that you can use any "mini" headphone jack, you don't need the "special" iPhone headphones. You can use any mini jack headphones.

  • Here we go again- 3g AND Edge data problems - NYC area

    Just great.... been having great 3G data speeds for the past several weeks (after the data outage) and since last night (10/12) I cannot get a page to load. Sometimes it doesn't load at all, other times it takes about 5 minutes. What the heck is going on? I am in Woodside, Queens. I tried restarting/Restoring/etc...all that usual good stuff. Also, Edge seems to be affected as well. Anyone else having the same problems?
    By the way- Same problem on my wife's 3G phone.

    Symptoms for a week and a half:
    -Full 3g signal but zero data throughput. I'll try to visit a page and there's zero progress for a few minutes so I give up.
    -Dropped calls, sometimes 5+ within a minute while you're helplessly trying to redial someone.
    I've done multiple soft-reset efforts such as 3G off/on, airplane mode on/off, rebooting, etc. to no avail. Nothing seems to help so I'm convinced it's ATT and their network.
    I live near Times Square and work in SoHo. 5 full bars of 3g everywhere I go and the sad thing is... I've resorted to using edge only since the 3G isn't functional.
    So yea... right now I paid a pretty penny to upgrade my 1st gen iPhone to essentially have GPS, a flush headphone jack and slightly improved speakers.

  • IPhone 3G S: Audio Jack

    I'm not sure where I can post this yet but does anyone know if the audio jack in the new iPhone 3G S be able to directly connect to an audio in line (ie: in a car) without having to get some converter like the old ones?

    I think the confusion here is the recessed connector in the original iPhone. You don't necessarily need the TTY adapter, just a specific adapter for the iPhone. I guess the TTY one already has the deeper plug built-in. To answer the question, though, this issue was fixed with the iPhone 3G, which got a flush headphone jack. One can safely assume it's the same in the 3G S.

  • Why Does Apple Keep Changing the Charging Protocols?

    I bought an iPhone 3G yesterday, and after having a 1st-Gen iPhone for about 5 months, I'd have to say I'm not altogether impressed with the new one. Non-recessed headphone jack, check; faster downloads over 3G, check. The rest of it.. I dunno.
    The most irksome detail I've encountered so far is that something has changed in the -- what is it called, the docking mechanism at the bottom of the phone that connects to the dock -- that makes all my previous docks (and I have quite a few around the house) obsolete. Worse, this iPhone will not charge from the adapter I have in my car, the Dension ICE>Link which originally integrated all my iPod controls directly into my car stereo.
    When I got my first iPhone back in February, the first thing I noticed was that when I plugged it into an older "universal dock," I'd get an error message, "this accessory is not made to work with iPhone." I managed to work around it. I bought a new dock that is compatible, and I discovered that so long as I was using the iPhone as an iPod in my car, it would charge that way. So I wasn't losing battery charge if I listened to my iPhone/Pod in the car. That was good enough.
    Now, with 3G, first, I discover that the Universal dock that I purchased with the old iPhone generates the same stupid 'will not work with iPhone' message that the OLD iPhone generated with an older dock. So this iPhone 3G does not work with a dock that I purchased for the original iPhone, which did not work with the dock I had purchased for my iPods. Sheesh.
    But, again, it gets worse: now, when I slip the 3G unit into the cradle/adapter in my car, it will not charge ever, not even when I'm using the iPhone 3G as an iPod. The audio connects, I can still use the iPhone as an iPod and listen to it and control it through the car stereo, but I'm draining the battery when I do.
    So, from iPod, to iPhone, to iPhone 3G, it appears to me that Apple has changed something in the protocols for each new generation so that all the docks and accessories from the previous generation are no longer viable. Why are they doing that? What is the UPSIDE of this very obvious and irritating downside, other than the upside for Apple that gets to sell me ever more accessories.
    Are other iPhone 3G users encountering irritations like this? What sort of work around are there? Anything?
    The GPS and the faster data speeds of 3G are nice features, it's also nice to have a flush headphone mount (I can use this one with a bluetooth stereo headset transmitter). But there are other ways that this unit is just not integrating into the way want to use it, and I may be very tempted to go back to the original iPhone.
    Anybody want to chime in with their experience?
    Thanks,
    --PS

    There are two messages you might see. The one you allude to, "will not work with iPhone" is merely a warning that the accessory is not shielded against the electronic emissions of the iPhone, i.e. you may get a little static on the audio. You can ignore that error and use the accessory. The other error is a "will not charge" and that's because the iPhone 3G no longer draws power from the FireWire pins in the dock connector. Apple has been phasing out FW support - the ability to sync via FW was dropeed a couple of years ago. 3rd party manufacturers have known about this for some time, but seemingly chose to maximize profit by not changing their design (especially for car chargers, since the power input is 12 V, which FW can handle, but for USB the voltage must be stepped down to 5 V). There are dongles available to drop the voltage and move the power to the correct pins.

  • Is the headphone jack flush on the new iphone 3gs?

    i was just curious if they left the headphone jack flush like the iphone 3g?

    Yes .. big improvement over my 2G in that respect (and many others).
    But choosing a case which does not interfere with some headphone plugs can still be an issue.
    Phil

  • TS3700 My headphones are flush, but the music still stops when the display goes dim.

    I reviewed the apple support recommendation for my music stopping for no reason and ensured my headphones were flush, but this is still occurring.  Any ideas?

    I have a new I Pod Nano 6th Gen and took to apple store cause the music would also stop playing and the headphones were not working. Apple was able to restoe it due to the voice over button had been hit by accident so screen would not work tried to do the power and volume down reset but would not work also and took them about 10 mins to get it restored at the store. And the headphone problem was due to small amount of debris stuck down in the headphone jack. They had looked at hole for earbuds and saw that something was blocking the headphones from seating all the way.. They tried with their tools to clear and could not get out the object with their tools but showed me how to  look down the plug for the headphones with a flaslight and you should be able too  see a small white dot at bottom of plug and if you can not see white dot at the bottom   something is in the hole blocking it.. I took a needle and gently tried to  pull object out and was able to break up small piece of debris that had got jammed in hole and then the debris  came right out when turn over the nano and shook out small amount  of the debris and then looked with flash light down plug hole and was able to see whit dot and was able to put headphones in and they worked fine.  I do not recommend to try this if do not have good hand skills and can GENTLY break up piece of debris to shake out took about ten mins to clean out and see the white spot at the bottom indicating plug was now unblocked and saved $75.00 for a replacement nano that was a 16gb that cost me $100.00 to buy new factory sealed   Good Luck but they were very helpful at the store!!!...resetting unit quickly and pain free

  • TS3700 My ipod stills pauses when the display turns off, even though, my headphones are correctly attached (or flushed)

    My ipod stills pauses when the display turns off, even though, my headphones are correctly attached (or flushed)

    Does this happen still when you use another set of headphones? Have you check to make sure the headphone jack is clean and clear of debris?  If so, the jack may be faulty or damaged meaning you'll need to take or send your iPod in for service/repair.
    B-rock

  • How can I get my headphone cable to plug in flush in to my nano 6th gen.?

    The cable for my headphones don't seem to want to click all the way into the nano socket. I've tried multiple headphones. I assume something must be preventing it, but it is not obvious. Now what?

    This is an older nano, so I assume it did work before...?  Is it possible that there is something, like a small piece of debris, inside the headphone jack that is preventing the plug from being fully inserted?

  • Headphone output stopped working (snd-hda, Dell XPS 13)

    Update: I got it working! See my second post; I will leave this here as a reference for those with the same problem.
    My headphone output stopped working, and my integrated microphone also stopped working. The speakers work fine, though.
    AFAIK, I didn't do anything, and am quite baffled as to why this is. It's worked fine for half a year.
    I have a Dell XPS 13; it came installed with Ubuntu, I booted that, where it *does* work (just to eliminate hardware problems).
    I'm running 3.16.4-1; I also downgraded to 3.16.3, which didn't help.
    I'm testing with speaker-test and mplayer -ao alsa; I normally use PulseAudio, but eliminating that for testing seemed like a sane thing to do. It doesn't work either way.
    I also downloaded the hda_analyzer, that has a lot of options, but I'm not sure what most of them mean...
    The closest I've been able to get at the problem is this:
    [~]% alsactl monitor
    card 0, #17 (0,0,0,Headphone Mic Jack,0) VALUE
    card 0, #17 (0,0,0,Headphone Mic Jack,0) VALUE
    This is an insert & remove of my headphone jack; ALSA does detect something it seems. It's listed as "Headphone Mic Jack", is this right?
    Any hints would be greatly appreciated!
    More info:
    [~]% cat /etc/modprobe.d/alsa-base.conf
    options snd-hda-intel enable=0,1
    options snd-hda-intel model=dell-headset-multi,dell-headset-multi
    This is required to get this to work in the first place, and always has worked; I tried some other options, to no avail. the enable=0,1 is to disable the HDMI output (disabling this has no effect either).
    $ cat /sys/module/snd_hda_intel/parameters/model
    dell-headset-multi,dell-headset-multi,(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null), +(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    To verify these options are actually being used
    $ id -Gn
    martin wheel video audio vboxusers nfs
    I'm in the audio group, not sure if this is required, but can't hurt.
    [~]# cat /etc/asound.conf
    # Use PulseAudio by default
    pcm.!default {
    type pulse
    fallback "sysdefault"
    hint {
    show on
    description "Default ALSA Output (currently PulseAudio Sound Server)"
    ctl.!default {
    type pulse
    fallback "sysdefault"
    # vim:set ft=alsaconf:
    Nothing special ... pulseaudio is more or less mandatory these days. ~/.asoundrc doesn't exist.
    Some misc. info:
    $ grep Codec /proc/asound/card*/codec*
    Codec: Realtek ALC3661
    [~]% lsmod | grep ^snd
    snd_usb_audio 135316 0
    snd_usbmidi_lib 27484 1 snd_usb_audio
    snd_rawmidi 26806 1 snd_usbmidi_lib
    snd_seq_device 13132 1 snd_rawmidi
    snd_hda_codec_realtek 67127 1
    snd_hda_codec_generic 63126 1 snd_hda_codec_realtek
    snd_hda_intel 26327 3
    snd_hda_controller 26727 1 snd_hda_intel
    snd_hda_codec 108552 4 snd_hda_codec_realtek,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
    snd_hwdep 17244 2 snd_usb_audio,snd_hda_codec
    snd_pcm 88487 4 snd_usb_audio,snd_hda_codec,snd_hda_intel,snd_hda_controller
    snd_timer 26614 1 snd_pcm
    snd 73436 17 snd_hda_codec_realtek,snd_usb_audio,snd_hwdep,snd_timer,snd_pcm,snd_rawmidi,snd_hda_codec_generic,snd_usbmidi_lib,snd_hda_codec,snd_hda_intel,snd_seq_device
    $ lspci -vv
    00:03.0 Audio device: Intel Corporation Haswell-ULT HD Audio Controller (rev 09)
    Subsystem: Dell Device 060a
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at f0510000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: <access denied>
    Kernel modules: snd_hda_intel
    00:1b.0 Audio device: Intel Corporation 8 Series HD Audio Controller (rev 04)
    Subsystem: Dell Device 060a
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 59
    Region 0: Memory at f0514000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: <access denied>
    Kernel driver in use: snd_hda_intel
    Kernel modules: snd_hda_intel
    $ dmesg
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.16.4-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 20140903 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Oct 6 08:22:27 CEST 2014
    [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=7259ebb8-c940-4659-a99c-66226a58659c rw quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009cfff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c2879fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000c287a000-0x00000000dceeefff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000dceef000-0x00000000dcf9efff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000dcf9f000-0x00000000dcffefff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000dcfff000-0x00000000df9fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ff980000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f5fffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.7 present.
    [ 0.000000] DMI: Dell Inc. XPS13 9333/0GFTRT, BIOS A02 12/11/2013
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x21f600 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: write-back
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 00E0000000 mask 7FE0000000 uncachable
    [ 0.000000] 1 base 00DE000000 mask 7FFE000000 uncachable
    [ 0.000000] 2 base 00DD000000 mask 7FFF000000 uncachable
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] 8 disabled
    [ 0.000000] 9 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: last_pfn = 0xc287a max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000f0100-0x000f010f] mapped at [ffff8800000f0100]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
    [ 0.000000] Using GB pages for direct mapping
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b23000, 0x01b23fff] PGTABLE
    [ 0.000000] BRK [0x01b24000, 0x01b24fff] PGTABLE
    [ 0.000000] BRK [0x01b25000, 0x01b25fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x21f400000-0x21f5fffff]
    [ 0.000000] [mem 0x21f400000-0x21f5fffff] page 2M
    [ 0.000000] BRK [0x01b26000, 0x01b26fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x21c000000-0x21f3fffff]
    [ 0.000000] [mem 0x21c000000-0x21f3fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x200000000-0x21bffffff]
    [ 0.000000] [mem 0x200000000-0x21bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0xc2879fff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
    [ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
    [ 0.000000] [mem 0xc0000000-0xc27fffff] page 2M
    [ 0.000000] [mem 0xc2800000-0xc2879fff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
    [ 0.000000] [mem 0x100000000-0x1ffffffff] page 1G
    [ 0.000000] RAMDISK: [mem 0x3796a000-0x37cacfff]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x00000000000F0120 000024 (v02 DELL )
    [ 0.000000] ACPI: XSDT 0x00000000DCFFE170 0000BC (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: FACP 0x00000000DCFFB000 00010C (v05 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: DSDT 0x00000000DCFE6000 010557 (v02 DELL HSW-LPT 00000000 INTL 20120711)
    [ 0.000000] ACPI: FACS 0x00000000DCF9C000 000040
    [ 0.000000] ACPI: ASF! 0x00000000DCFFD000 0000A5 (v32 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: HPET 0x00000000DCFFA000 000038 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: LPIT 0x00000000DCFF9000 000094 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: APIC 0x00000000DCFF8000 000098 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: MCFG 0x00000000DCFF7000 00003C (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: SSDT 0x00000000DCFE5000 000228 (v01 DELL sensrhub 00000000 INTL 20120711)
    [ 0.000000] ACPI: SSDT 0x00000000DCFE2000 002028 (v01 DELL PtidDevc 00001000 INTL 20120711)
    [ 0.000000] ACPI: SSDT 0x00000000DCFE1000 000539 (v01 DELL Cpu0Ist 00003000 INTL 20120711)
    [ 0.000000] ACPI: SSDT 0x00000000DCFE0000 000AD8 (v01 DELL CpuPm 00003000 INTL 20120711)
    [ 0.000000] ACPI: SSDT 0x00000000DCFDC000 003641 (v01 DELL SaSsdt 00003000 INTL 20120711)
    [ 0.000000] ACPI: UEFI 0x00000000DCFDB000 000042 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: POAT 0x00000000DCF77000 000055 (v03 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: BATB 0x00000000DCFDA000 000046 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: FPDT 0x00000000DCFD9000 000064 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: SLIC 0x00000000DCFD8000 000176 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: UEFI 0x00000000DCFD7000 0002A6 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: SSDT 0x00000000DCFD6000 0005C1 (v01 DELL IsctTabl 00001000 INTL 20120711)
    [ 0.000000] ACPI: CSRT 0x00000000DCFD4000 0000C4 (v01 DELL QA09 00000002 LOHR 00000002)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000021f5fffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x21f5fffff]
    [ 0.000000] NODE_DATA [mem 0x21f5f9000-0x21f5fdfff]
    [ 0.000000] [ffffea0000000000-ffffea00087fffff] PMD -> [ffff880217200000-ffff88021ebfffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x21f5fffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009cfff]
    [ 0.000000] node 0: [mem 0x00100000-0xc2879fff]
    [ 0.000000] node 0: [mem 0x100000000-0x21f5fffff]
    [ 0.000000] On node 0 totalpages: 1973782
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3996 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 12386 pages used for memmap
    [ 0.000000] DMA32 zone: 792698 pages, LIFO batch:31
    [ 0.000000] Normal zone: 18392 pages used for memmap
    [ 0.000000] Normal zone: 1177088 pages, LIFO batch:31
    [ 0.000000] Reserving Intel graphics stolen memory at 0xdda00000-0xdf9fffff
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 56
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc287a000-0xdceeefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xdceef000-0xdcf9efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xdcf9f000-0xdcffefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xdcfff000-0xdf9fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfe100fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfe113000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff97ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xff980000-0xffffffff]
    [ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88021f200000 s86784 r8192 d23808 u262144
    [ 0.000000] pcpu-alloc: s86784 r8192 d23808 u262144 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1942919
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=7259ebb8-c940-4659-a99c-66226a58659c rw quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
    [ 0.000000] AGP: Checking aperture...
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 7688084K/7895128K available (5336K kernel code, 887K rwdata, 1688K rodata, 1128K init, 1164K bss, 207044K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
    [ 0.000000] NR_IRQS:8448 nr_irqs:1016 16
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 31981568 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 2394.295 MHz processor
    [ 0.000039] Calibrating delay loop (skipped), value calculated using timer frequency.. 4790.11 BogoMIPS (lpj=7980983)
    [ 0.000042] pid_max: default: 32768 minimum: 301
    [ 0.000050] ACPI: Core revision 20140424
    [ 0.020000] ACPI: All ACPI Tables successfully acquired
    [ 0.020260] Security Framework initialized
    [ 0.020267] Yama: becoming mindful.
    [ 0.020937] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
    [ 0.022978] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.023836] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.023849] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.024116] Initializing cgroup subsys memory
    [ 0.024140] Initializing cgroup subsys devices
    [ 0.024147] Initializing cgroup subsys freezer
    [ 0.024150] Initializing cgroup subsys net_cls
    [ 0.024155] Initializing cgroup subsys blkio
    [ 0.024183] CPU: Physical Processor ID: 0
    [ 0.024184] CPU: Processor Core ID: 0
    [ 0.024189] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.025376] mce: CPU supports 7 MCE banks
    [ 0.025391] CPU0: Thermal monitoring enabled (TM1)
    [ 0.025404] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
    Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
    tlb_flushall_shift: 6
    [ 0.025524] Freeing SMP alternatives memory: 20K (ffffffff819f9000 - ffffffff819fe000)
    [ 0.026475] ftrace: allocating 20445 entries in 80 pages
    [ 0.038058] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.071090] smpboot: CPU0: Intel(R) Core(TM) i7-4500U CPU @ 1.80GHz (fam: 06, model: 45, stepping: 01)
    [ 0.071098] TSC deadline timer enabled
    [ 0.071124] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
    [ 0.071149] ... version: 3
    [ 0.071150] ... bit width: 48
    [ 0.071151] ... generic registers: 4
    [ 0.071152] ... value mask: 0000ffffffffffff
    [ 0.071154] ... max period: 0000ffffffffffff
    [ 0.071155] ... fixed-purpose events: 3
    [ 0.071156] ... event mask: 000000070000000f
    [ 0.097907] x86: Booting SMP configuration:
    [ 0.097909] .... node #0, CPUs: #1
    [ 0.112630] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.119293] #2 #3
    [ 0.154938] x86: Booted up 1 node, 4 CPUs
    [ 0.154942] smpboot: Total of 4 processors activated (19162.45 BogoMIPS)
    [ 0.160676] devtmpfs: initialized
    [ 0.163608] PM: Registering ACPI NVS region [mem 0xdceef000-0xdcf9efff] (720896 bytes)
    [ 0.164642] pinctrl core: initialized pinctrl subsystem
    [ 0.164688] RTC time: 22:42:27, date: 10/21/14
    [ 0.164750] NET: Registered protocol family 16
    [ 0.164884] cpuidle: using governor ladder
    [ 0.164887] cpuidle: using governor menu
    [ 0.164916] ACPI: bus type PCI registered
    [ 0.164918] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.165012] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    [ 0.165014] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    [ 0.165118] PCI: Using configuration type 1 for base access
    [ 0.165125] dmi type 0xB1 record - unknown flag
    [ 0.177572] ACPI: Added _OSI(Module Device)
    [ 0.177575] ACPI: Added _OSI(Processor Device)
    [ 0.177577] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.177578] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.183007] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.194850] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.207326] ACPI: Dynamic OEM Table Load:
    [ 0.207339] ACPI: SSDT 0xFFFF880213EE7000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120711)
    [ 0.220827] ACPI: Dynamic OEM Table Load:
    [ 0.220838] ACPI: SSDT 0xFFFF880213F81000 0005AA (v01 PmRef ApIst 00003000 INTL 20120711)
    [ 0.237345] ACPI: Dynamic OEM Table Load:
    [ 0.237354] ACPI: SSDT 0xFFFF880213F56200 000119 (v01 PmRef ApCst 00003000 INTL 20120711)
    [ 0.255255] ACPI: Interpreter enabled
    [ 0.255267] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
    [ 0.255275] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
    [ 0.255298] ACPI: (supports S0 S3 S4 S5)
    [ 0.255300] ACPI: Using IOAPIC for interrupt routing
    [ 0.255336] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.268419] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
    [ 0.268426] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.268573] \_SB_.PCI0:_OSC invalid UUID
    [ 0.268575] _OSC request data:1 1f 0
    [ 0.268579] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
    [ 0.269580] PCI host bridge to bus 0000:00
    [ 0.269584] pci_bus 0000:00: root bus resource [bus 00-3e]
    [ 0.269586] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.269588] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.269590] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.269592] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
    [ 0.269601] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
    [ 0.269803] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
    [ 0.269817] pci 0000:00:02.0: reg 0x10: [mem 0xf0000000-0xf03fffff 64bit]
    [ 0.269826] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.269831] pci 0000:00:02.0: reg 0x20: [io 0x3000-0x303f]
    [ 0.270019] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
    [ 0.270029] pci 0000:00:03.0: reg 0x10: [mem 0xf0510000-0xf0513fff 64bit]
    [ 0.270244] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
    [ 0.270263] pci 0000:00:14.0: reg 0x10: [mem 0xf0500000-0xf050ffff 64bit]
    [ 0.270324] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 0.270459] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 0.270505] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
    [ 0.270526] pci 0000:00:16.0: reg 0x10: [mem 0xf0519000-0xf051901f 64bit]
    [ 0.270598] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 0.270790] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
    [ 0.270806] pci 0000:00:1b.0: reg 0x10: [mem 0xf0514000-0xf0517fff 64bit]
    [ 0.270876] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.271011] pci 0000:00:1b.0: System wakeup disabled by ACPI
    [ 0.271060] pci 0000:00:1c.0: [8086:9c10] type 01 class 0x060400
    [ 0.271140] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.271279] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 0.271327] pci 0000:00:1c.2: [8086:9c14] type 01 class 0x060400
    [ 0.271410] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.271549] pci 0000:00:1c.2: System wakeup disabled by ACPI
    [ 0.271602] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
    [ 0.271624] pci 0000:00:1d.0: reg 0x10: [mem 0xf051d000-0xf051d3ff]
    [ 0.271716] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
    [ 0.271867] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.271914] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
    [ 0.272193] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
    [ 0.272209] pci 0000:00:1f.2: reg 0x10: [io 0x3088-0x308f]
    [ 0.272217] pci 0000:00:1f.2: reg 0x14: [io 0x3094-0x3097]
    [ 0.272225] pci 0000:00:1f.2: reg 0x18: [io 0x3080-0x3087]
    [ 0.272232] pci 0000:00:1f.2: reg 0x1c: [io 0x3090-0x3093]
    [ 0.272240] pci 0000:00:1f.2: reg 0x20: [io 0x3060-0x307f]
    [ 0.272247] pci 0000:00:1f.2: reg 0x24: [mem 0xf051c000-0xf051c7ff]
    [ 0.272285] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.272451] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
    [ 0.272466] pci 0000:00:1f.3: reg 0x10: [mem 0xf0518000-0xf05180ff 64bit]
    [ 0.272486] pci 0000:00:1f.3: reg 0x20: [io 0xefa0-0xefbf]
    [ 0.272737] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.272853] pci 0000:02:00.0: [8086:08b1] type 00 class 0x028000
    [ 0.272899] pci 0000:02:00.0: reg 0x10: [mem 0xf0400000-0xf0401fff 64bit]
    [ 0.273097] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 0.273145] pci 0000:02:00.0: System wakeup disabled by ACPI
    [ 0.277341] pci 0000:00:1c.2: PCI bridge to [bus 02]
    [ 0.277347] pci 0000:00:1c.2: bridge window [mem 0xf0400000-0xf04fffff]
    [ 0.294607] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
    [ 0.294666] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.294723] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *7
    [ 0.294778] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
    [ 0.294832] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.294886] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.294940] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
    [ 0.294995] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
    [ 0.295346] ACPI: Enabled 5 GPEs in block 00 to 7F
    [ 0.295416] ACPI : EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
    [ 0.295555] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.295559] vgaarb: loaded
    [ 0.295560] vgaarb: bridge control possible 0000:00:02.0
    [ 0.295603] PCI: Using ACPI for IRQ routing
    [ 0.297024] PCI: pci_cache_line_size set to 64 bytes
    [ 0.297085] e820: reserve RAM buffer [mem 0x0009d000-0x0009ffff]
    [ 0.297087] e820: reserve RAM buffer [mem 0xc287a000-0xc3ffffff]
    [ 0.297088] e820: reserve RAM buffer [mem 0x21f600000-0x21fffffff]
    [ 0.297209] NetLabel: Initializing
    [ 0.297211] NetLabel: domain hash size = 128
    [ 0.297212] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.297225] NetLabel: unlabeled traffic allowed by default
    [ 0.297250] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 0.297256] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 0.299294] Switched to clocksource hpet
    [ 0.305097] pnp: PnP ACPI init
    [ 0.305113] ACPI: bus type PNP registered
    [ 0.305253] system 00:00: [io 0x0680-0x069f] has been reserved
    [ 0.305256] system 00:00: [io 0xffff] has been reserved
    [ 0.305259] system 00:00: [io 0xffff] has been reserved
    [ 0.305262] system 00:00: [io 0xffff] has been reserved
    [ 0.305265] system 00:00: [io 0x1800-0x18fe] could not be reserved
    [ 0.305267] system 00:00: [io 0x164e-0x164f] has been reserved
    [ 0.305270] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.305325] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.305378] system 00:02: [io 0x1854-0x1857] has been reserved
    [ 0.305381] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 0.305426] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.305459] pnp 00:04: Plug and Play ACPI device, IDs SYN0608 PNP0f03 (active)
    [ 0.305612] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.305614] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
    [ 0.305617] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.305619] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.305621] system 00:05: [mem 0xf8000000-0xfbffffff] has been reserved
    [ 0.305623] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.305625] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
    [ 0.305627] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
    [ 0.305630] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
    [ 0.305632] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
    [ 0.305634] system 00:05: [mem 0xdfa10000-0xdfa1ffff] has been reserved
    [ 0.305637] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.305958] system 00:06: [mem 0xfe102000-0xfe102fff] has been reserved
    [ 0.305961] system 00:06: [mem 0xfe104000-0xfe104fff] has been reserved
    [ 0.305971] system 00:06: [mem 0xfe106000-0xfe106fff] has been reserved
    [ 0.305974] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.306696] pnp: PnP ACPI: found 7 devices
    [ 0.306698] ACPI: bus type PNP unregistered
    [ 0.313588] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.313602] pci 0000:00:1c.2: PCI bridge to [bus 02]
    [ 0.313608] pci 0000:00:1c.2: bridge window [mem 0xf0400000-0xf04fffff]
    [ 0.313617] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.313620] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.313622] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.313624] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfeafffff]
    [ 0.313626] pci_bus 0000:02: resource 1 [mem 0xf0400000-0xf04fffff]
    [ 0.313661] NET: Registered protocol family 2
    [ 0.313895] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.314065] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.314196] TCP: Hash tables configured (established 65536 bind 65536)
    [ 0.314216] TCP: reno registered
    [ 0.314229] UDP hash table entries: 4096 (order: 5, 131072 bytes)
    [ 0.314260] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
    [ 0.314329] NET: Registered protocol family 1
    [ 0.314345] pci 0000:00:02.0: Boot video device
    [ 0.314427] pci 0000:00:14.0: can't derive routing for PCI INT A
    [ 0.314429] pci 0000:00:14.0: PCI INT A: no GSI
    [ 0.314520] pci 0000:00:14.0: can't derive routing for PCI INT A
    [ 0.314702] PCI: CLS 64 bytes, default 64
    [ 0.314746] Unpacking initramfs...
    [ 0.389760] Freeing initrd memory: 3340K (ffff88003796a000 - ffff880037cad000)
    [ 0.389768] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.389771] software IO TLB [mem 0xbe87a000-0xc287a000] (64MB) mapped at [ffff8800be87a000-ffff8800c2879fff]
    [ 0.389991] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
    [ 0.390043] Scanning for low memory corruption every 60 seconds
    [ 0.390383] futex hash table entries: 2048 (order: 5, 131072 bytes)
    [ 0.390776] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.392315] zbud: loaded
    [ 0.392526] VFS: Disk quotas dquot_6.5.2
    [ 0.392564] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.392709] msgmni has been set to 15022
    [ 0.392776] Key type big_key registered
    [ 0.392952] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.393009] io scheduler noop registered
    [ 0.393014] io scheduler deadline registered
    [ 0.393072] io scheduler cfq registered (default)
    [ 0.393422] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.393440] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.393482] intel_idle: MWAIT substates: 0x11142120
    [ 0.393484] intel_idle: v0.4 model 0x45
    [ 0.393485] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 0.393772] GHES: HEST is not enabled!
    [ 0.393860] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.394367] Linux agpgart interface v0.103
    [ 0.394421] rtc_cmos 00:01: RTC can wake from S4
    [ 0.394566] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
    [ 0.394596] rtc_cmos 00:01: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    [ 0.394611] Intel P-state driver initializing.
    [ 0.394625] Intel pstate controlling: cpu 0
    [ 0.394647] Intel pstate controlling: cpu 1
    [ 0.394663] Intel pstate controlling: cpu 2
    [ 0.394684] Intel pstate controlling: cpu 3
    [ 0.394756] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.395139] TCP: cubic registered
    [ 0.395367] NET: Registered protocol family 10
    [ 0.395811] NET: Registered protocol family 17
    [ 0.396487] registered taskstats version 1
    [ 0.397305] Magic number: 2:622:755
    [ 0.397469] rtc_cmos 00:01: setting system clock to 2014-10-21 22:42:27 UTC (1413931347)
    [ 0.397659] PM: Hibernation image not present or could not be loaded.
    [ 0.399550] Freeing unused kernel memory: 1128K (ffffffff818df000 - ffffffff819f9000)
    [ 0.399554] Write protecting the kernel read-only data: 8192k
    [ 0.403618] Freeing unused kernel memory: 796K (ffff880001539000 - ffff880001600000)
    [ 0.404603] Freeing unused kernel memory: 360K (ffff8800017a6000 - ffff880001800000)
    [ 0.411279] random: systemd-tmpfile urandom read with 4 bits of entropy available
    [ 0.412549] systemd-udevd[57]: starting version 216
    [ 0.429661] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    [ 0.430313] sdhci: Secure Digital Host Controller Interface driver
    [ 0.430315] sdhci: Copyright(c) Pierre Ossman
    [ 0.435942] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.436007] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.441502] ACPI: bus type USB registered
    [ 0.441544] usbcore: registered new interface driver usbfs
    [ 0.441562] usbcore: registered new interface driver hub
    [ 0.441712] usbcore: registered new device driver usb
    [ 0.442370] SCSI subsystem initialized
    [ 0.442606] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.442897] ehci-pci: EHCI PCI platform driver
    [ 0.443091] ehci-pci 0000:00:1d.0: EHCI Host Controller
    [ 0.443106] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
    [ 0.443121] ehci-pci 0000:00:1d.0: debug port 2
    [ 0.444256] libata version 3.00 loaded.
    [ 0.447021] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
    [ 0.447046] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf051d000
    [ 0.456197] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
    [ 0.456468] hub 1-0:1.0: USB hub found
    [ 0.456636] hub 1-0:1.0: 2 ports detected
    [ 0.456998] xhci_hcd 0000:00:14.0: can't derive routing for PCI INT A
    [ 0.457003] xhci_hcd 0000:00:14.0: PCI INT A: no GSI
    [ 0.457028] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.457038] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
    [ 0.457132] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 0.457158] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
    [ 0.457437] hub 2-0:1.0: USB hub found
    [ 0.457454] hub 2-0:1.0: 9 ports detected
    [ 0.460686] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.460692] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
    [ 0.460861] hub 3-0:1.0: USB hub found
    [ 0.460871] hub 3-0:1.0: 4 ports detected
    [ 0.461773] ahci 0000:00:1f.2: version 3.0
    [ 0.461915] ahci 0000:00:1f.2: irq 57 for MSI/MSI-X
    [ 0.471676] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.472802] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x4 impl SATA mode
    [ 0.472807] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
    [ 0.473307] scsi0 : ahci
    [ 0.473445] scsi1 : ahci
    [ 0.473555] scsi2 : ahci
    [ 0.473668] scsi3 : ahci
    [ 0.473715] ata1: DUMMY
    [ 0.473717] ata2: DUMMY
    [ 0.473719] ata3: SATA max UDMA/133 abar m2048@0xf051c000 port 0xf051c200 irq 57
    [ 0.473721] ata4: DUMMY
    [ 0.763125] usb 1-1: new high-speed USB device number 2 using ehci-pci
    [ 0.793107] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 0.793458] ata3.00: ATA-8: LITEONIT LMT-256M6M mSATA 256GB, DM8110F, max UDMA/133
    [ 0.793461] ata3.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
    [ 0.794069] ata3.00: configured for UDMA/133
    [ 0.794234] scsi 2:0:0:0: Direct-Access ATA LITEONIT LMT-256 10F PQ: 0 ANSI: 5
    [ 0.798767] sd 2:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
    [ 0.798902] sd 2:0:0:0: [sda] Write Protect is off
    [ 0.798906] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 0.798943] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 0.799393] sda: sda3 sda4
    [ 0.799749] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 0.841216] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 0.887143] hub 1-1:1.0: USB hub found
    [ 0.887202] hub 1-1:1.0: 8 ports detected
    [ 0.946321] systemd[1]: Cannot add dependency job for unit nfs-server.target, ignoring: Unit nfs-server.target failed to load: No such file or directory.
    [ 0.946348] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 0.960139] EXT4-fs (sda4): re-mounted. Opts: data=ordered,discard
    [ 0.981520] FS-Cache: Loaded
    [ 0.992070] RPC: Registered named UNIX socket transport module.
    [ 0.992075] RPC: Registered udp transport module.
    [ 0.992077] RPC: Registered tcp transport module.
    [ 0.992079] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 1.004660] FS-Cache: Netfs 'nfs' registered for caching
    [ 1.007058] Netfilter messages via NETLINK v0.30.
    [ 1.008839] nf_tables: (c) 2007-2009 Patrick McHardy <[email protected]>
    [ 1.023856] vboxdrv: Found 4 processor cores.
    [ 1.024080] vboxdrv: fAsync=0 offMin=0x2c2 offMax=0x31e0
    [ 1.024169] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
    [ 1.024172] vboxdrv: Successfully loaded version 4.3.18_OSE (interface 0x001a0008).
    [ 1.046603] usb 2-3: new full-speed USB device number 2 using xhci_hcd
    [ 1.322293] systemd-udevd[170]: starting version 216
    [ 1.380209] usb 2-5: new high-speed USB device number 3 using xhci_hcd
    [ 1.393592] tsc: Refined TSC clocksource calibration: 2394.460 MHz
    [ 1.439202] systemd-journald[135]: Received request to flush runtime journal from PID 1
    [ 1.471000] hidraw: raw HID events driver (C) Jiri Kosina
    [ 1.476250] systemd-journald[135]: File /var/log/journal/88482a6e208046b4ab2b978eaa052ecd/system.journal corrupted or uncleanly shut down, renaming and replacing.
    [ 1.510556] thermal LNXTHERM:00: registered as thermal_zone0
    [ 1.510560] ACPI: Thermal Zone [TZ00] (28 C)
    [ 1.510856] thermal LNXTHERM:01: registered as thermal_zone1
    [ 1.510860] ACPI: Thermal Zone [TZ01] (30 C)
    [ 1.516235] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 1.526161] ACPI Warning: SystemIO range 0x000000000000efa0-0x000000000000efbf conflicts with OpRegion 0x000000000000efa0-0x000000000000efaf (\_SB_.PCI0.SBUS.SMBI) (20140424/utaddress-258)
    [ 1.526172] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 1.545038] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
    [ 1.552395] cfg80211: Calling CRDA to update world regulatory domain
    [ 1.576090] [drm] Initialized drm 1.1.0 20060810
    [ 1.580291] random: nonblocking pool is initialized
    [ 1.596486] Intel(R) Wireless WiFi driver for Linux, in-tree:
    [ 1.596490] Copyright(c) 2003- 2014 Intel Corporation
    [ 1.596517] snd_hda_intel: probe of 0000:00:03.0 failed with error -2
    [ 1.596724] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
    [ 1.597671] iwlwifi 0000:02:00.0: irq 60 for MSI/MSI-X
    [ 1.606282] iwlwifi 0000:02:00.0: loaded firmware version 23.214.9.0 op_mode iwlmvm
    [ 1.622623] sound hdaudioC0D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
    [ 1.622630] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    [ 1.622633] sound hdaudioC0D0: hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
    [ 1.622636] sound hdaudioC0D0: mono: mono_out=0x0
    [ 1.622639] sound hdaudioC0D0: inputs:
    [ 1.622643] sound hdaudioC0D0: Headphone Mic=0x19
    [ 1.622646] sound hdaudioC0D0: Headset Mic=0x1b
    [ 1.622649] sound hdaudioC0D0: Internal Mic=0x12
    [ 1.627117] ACPI: AC Adapter [ADP0] (off-line)
    [ 1.628753] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
    [ 1.628924] ACPI: Power Button [PWRB]
    [ 1.629010] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input5
    [ 1.630785] ACPI: Lid Switch [LID0]
    [ 1.630887] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
    [ 1.631327] ACPI: Power Button [PWRF]
    [ 1.633943] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input3
    [ 1.634197] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
    [ 1.635366] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x16
    [ 1.635406] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x16
    [ 1.635428] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x16
    [ 1.635449] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x16
    [ 1.635520] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 1.639579] ACPI: Battery Slot [BAT0] (battery present)
    [ 1.640267] iwlwifi 0000:02:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
    [ 1.640997] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 1.641000] wmi: Mapper loaded
    [ 1.641249] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 1.644274] AVX2 version of gcm_enc/dec engaged.
    [ 1.662640] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
    [ 1.707814] iTCO_vendor_support: vendor-support=0
    [ 1.709016] [drm] Memory usable by graphics device = 2048M
    [ 1.709022] [drm] Replacing VGA console driver
    [ 1.710234] Console: switching to colour dummy device 80x25
    [ 1.710749] hid-rmi 0018:06CB:2734.0001: Scanning PDT...
    [ 1.711895] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    [ 1.711954] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
    [ 1.712089] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 1.713279] hid-rmi 0018:06CB:2734.0001: Found F34 on page 0x00
    [ 1.715870] hid-rmi 0018:06CB:2734.0001: Found F01 on page 0x00
    [ 1.718203] hid-rmi 0018:06CB:2734.0001: Found F11 on page 0x00
    [ 1.724578] hid-rmi 0018:06CB:2734.0001: Found F54 on page 0x01
    [ 1.727275] hid-rmi 0018:06CB:2734.0001: Found F30 on page 0x01
    [ 1.730545] i915 0000:00:02.0: irq 61 for MSI/MSI-X
    [ 1.730561] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 1.730563] [drm] Driver supports precise vblank timestamp query.
    [ 1.730596] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 1.733539] hid-rmi 0018:06CB:2734.0001: Found F55 on page 0x02
    [ 1.738729] hid-rmi 0018:06CB:2734.0001: Found F51 on page 0x03
    [ 1.740512] usb 2-6: new full-speed USB device number 4 using xhci_hcd
    [ 1.744701] hid-rmi 0018:06CB:2734.0001: rmi_scan_pdt: Done with PDT scan.
    [ 1.756260] [drm] VBT doesn't support DRRS
    [ 1.758240] hid-rmi 0018:06CB:2734.0001: rmi_populate_f11: size in mm: 97 x 59
    [ 1.766636] input: DLL060A:00 06CB:2734 as /devices/pci0000:00/INT33C3:00/i2c-0/i2c-DLL060A:00/0018:06CB:2734.0001/input/input8
    [ 1.766734] hid-rmi 0018:06CB:2734.0001: input,hidraw0: <UNKNOWN> HID v1.00 Pointer [DLL060A:00 06CB:2734] on
    [ 1.775456] fbcon: inteldrmfb (fb0) is primary device
    [ 1.802968] input: Dell WMI hotkeys as /devices/virtual/input/input9
    [ 1.808667] mousedev: PS/2 mouse device common for all mice
    [ 1.841252] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
    [ 1.842535] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 1.842776] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 1.854793] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 2.394398] Switched to clocksource tsc
    [ 2.838140] Console: switching to colour frame buffer device 240x67
    [ 2.845934] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 2.845936] i915 0000:00:02.0: registered panic notifier
    [ 2.876371] media: Linux media interface: v0.10
    [ 2.876864] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 2.877001] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input10
    [ 2.877148] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 2.879690] usbcore: registered new interface driver usbhid
    [ 2.879694] usbhid: USB HID core driver
    [ 2.883145] Linux video capture interface: v2.00
    [ 2.892232] input: SYNAPTICS Synaptics Large Touch Screen as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.0/0003:06CB:0AF8.0002/input/input11
    [ 2.892497] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0bda:5752)
    [ 2.895106] hid-multitouch 0003:06CB:0AF8.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [SYNAPTICS Synaptics Large Touch Screen] on usb-0000:00:14.0-3/input0
    [ 2.895830] Bluetooth: Core ver 2.19
    [ 2.895849] NET: Registered protocol family 31
    [ 2.895852] Bluetooth: HCI device and connection manager initialized
    [ 2.895861] Bluetooth: HCI socket layer initialized
    [ 2.895864] Bluetooth: L2CAP socket layer initialized
    [ 2.895877] Bluetooth: SCO socket layer initialized
    [ 2.901636] input: Integrated_Webcam_HD as /devices/pci0000:00/0000:00:14.0/usb2/2-5/2-5:1.0/input/input13
    [ 2.901827] usbcore: registered new interface driver uvcvideo
    [ 2.901830] USB Video Class driver (1.1.1)
    [ 2.910511] usbcore: registered new interface driver btusb
    [ 2.925460] Bluetooth: hci0: read Intel version: 370710018002030d2e
    [ 2.925464] Bluetooth: hci0: Intel device is already patched. patch num: 2e
    [ 3.331899] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
    [ 11.275262] systemd-journald[135]: File /var/log/journal/88482a6e208046b4ab2b978eaa052ecd/user-1001.journal corrupted or uncleanly shut down, renaming and replacing.
    [ 35.164461] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 35.241753] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 35.241999] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 35.255097] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 36.055112] wlan0: authenticate with c0:25:06:84:57:f0
    [ 36.058891] wlan0: send auth to c0:25:06:84:57:f0 (try 1/3)
    [ 36.061335] wlan0: authenticated
    [ 36.061563] wlan0: associate with c0:25:06:84:57:f0 (try 1/3)
    [ 36.067260] wlan0: RX AssocResp from c0:25:06:84:57:f0 (capab=0x431 status=0 aid=1)
    [ 36.070080] wlan0: associated
    [ 36.070111] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 36.070172] cfg80211: Calling CRDA to update world regulatory domain
    [ 4501.338278] PM: Syncing filesystems ...
    [ 4501.341188] atkbd serio0: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0).
    [ 4501.341196] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
    [ 4501.348617] done.
    [ 4501.348622] PM: Preparing system for mem sleep
    [ 4501.349019] Freezing user space processes ... (elapsed 0.001 seconds) done.
    [ 4501.350459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
    [ 4501.351580] PM: Entering mem sleep
    [ 4501.351657] Suspending console(s) (use no_console_suspend to debug)
    [ 4501.351917] wlan0: deauthenticating from c0:25:06:84:57:f0 by local choice (Reason: 3=DEAUTH_LEAVING)
    [ 4501.358219] atkbd serio0: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0).
    [ 4501.358222] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
    [ 4501.361609] cfg80211: Calling CRDA for country: DE
    [ 4501.362122] sd 2:0:0:0: [sda] Synchronizing SCSI cache
    [ 4501.362185] sd 2:0:0:0: [sda] Stopping disk
    [ 4501.992409] PM: suspend of devices complete after 640.028 msecs
    [ 4502.005724] PM: late suspend of devices complete after 13.299 msecs
    [ 4502.006247] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
    [ 4502.006367] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
    [ 4502.019376] PM: noirq suspend of devices complete after 13.638 msecs
    [ 4502.019816] ACPI: Preparing to enter system sleep state S3
    [ 4502.020586] PM: Saving platform NVS memory
    [ 4502.021109] Disabling non-boot CPUs ...
    [ 4502.021139] intel_pstate CPU 1 exiting
    [ 4502.022404] kvm: disabling virtualization on CPU1
    [ 4502.022854] smpboot: CPU 1 is now offline
    [ 4502.023143] intel_pstate CPU 2 exiting
    [ 4502.024386] kvm: disabling virtualization on CPU2
    [ 4502.125774] smpboot: CPU 2 is now offline
    [ 4502.126039] intel_pstate CPU 3 exiting
    [ 4502.127395] kvm: disabling virtualization on CPU3
    [ 4502.229207] smpboot: CPU 3 is now offline
    [ 4502.232189] ACPI: Low-level resume complete
    [ 4502.232259] PM: Restoring platform NVS memory
    [ 4502.232774] Enabling non-boot CPUs ...
    [ 4502.232814] x86: Booting SMP configuration:
    [ 4502.232815] smpboot: Booting Node 0 Processor 1 APIC 0x1
    [ 4502.245238] kvm: enabling virtualization on CPU1
    [ 4502.247462] Intel pstate controlling: cpu 1
    [ 4502.247514] CPU1 is up
    [ 4502.247533] smpboot: Booting Node 0 Processor 2 APIC 0x2
    [ 4502.259870] kvm: enabling virtualization on CPU2
    [ 4502.262107] Intel pstate controlling: cpu 2
    [ 4502.262155] CPU2 is up
    [ 4502.262172] smpboot: Booting Node 0 Processor 3 APIC 0x3
    [ 4502.274504] kvm: enabling virtualization on CPU3
    [ 4502.276760] Intel pstate controlling: cpu 3
    [ 4502.276807] CPU3 is up
    [ 4502.282141] ACPI: Waking up from system sleep state S3
    [ 4502.302447] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 4502.302450] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
    [ 4502.302690] PM: noirq resume of devices complete after 11.863 msecs
    [ 4502.303102] PM: early resume of devices complete after 0.384 msecs
    [ 4502.303194] usb usb2: root hub lost power or was reset
    [ 4502.303197] usb usb3: root hub lost power or was reset
    [ 4502.315679] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
    [ 4502.315810] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
    [ 4502.329054] sd 2:0:0:0: [sda] Starting disk
    [ 4502.390642] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
    [ 4502.535888] usb 1-1: reset high-speed USB device number 2 using ehci-pci
    [ 4502.643402] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 4502.643646] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 4502.649288] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 4502.652119] ata3.00: configured for UDMA/133
    [ 4502.766135] usb 2-3: reset full-speed USB device number 2 using xhci_hcd
    [ 4502.939946] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880212c09480
    [ 4502.939950] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880212c094c8
    [ 4503.099825] usb 2-6: reset full-speed USB device number 4 using xhci_hcd
    [ 4503.273741] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bdea5a00
    [ 4503.273745] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bdea5a48
    [ 4503.273748] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bdea5a90
    [ 4503.273750] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88020c2a6000
    [ 4503.273752] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88020c2a6048
    [ 4503.274732] PM: resume of devices complete after 970.836 msecs
    [ 4503.275664] PM: Finishing wakeup.
    [ 4503.275668] Restarting tasks ...
    [ 4503.275774] iwlwifi 0000:02:00.0: no hotplug settings from platform
    [ 4503.276362] usb 2-5: USB disconnect, device number 3
    [ 4503.276546] pci_bus 0000:01: Allocating resources
    [ 4503.276576] pcieport 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
    [ 4503.276585] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
    [ 4503.276592] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
    [ 4503.276596] done.
    [ 4503.276614] pci_bus 0000:02: Allocating resources
    [ 4503.276646] pcieport 0000:00:1c.2: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
    [ 4503.276653] pcieport 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
    [ 4503.276662] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
    [ 4503.276675] pcieport 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
    [ 4503.276681] pcieport 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 4503.276688] pcieport 0000:00:1c.2: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 4503.276695] pcieport 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 4503.276701] pcieport 0000:00:1c.2: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 4503.276712] pcieport 0000:00:1c.0: BAR 14: assigned [mem 0xdfb00000-0xdfcfffff]
    [ 4503.276726] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0xdfd00000-0xdfefffff 64bit pref]
    [ 4503.276739] pcieport 0000:00:1c.2: BAR 15: assigned [mem 0xf0600000-0xf07fffff 64bit pref]
    [ 4503.276748] pcieport 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
    [ 4503.276756] pcieport 0000:00:1c.2: BAR 13: assigned [io 0x4000-0x4fff]
    [ 4503.276773] pci 0000:00:00.0: no hotplug settings from platform
    [ 4503.276778] pci 0000:00:00.0: using default PCI settings
    [ 4503.276791] i915 0000:00:02.0: no hotplug settings from platform
    [ 4503.276795] i915 0000:00:02.0: using default PCI settings
    [ 4503.276809] pci 0000:00:03.0: no hotplug settings from platform
    [ 4503.276816] xhci_hcd 0000:00:14.0: no hotplug settings from platform
    [ 4503.276820] xhci_hcd 0000:00:14.0: using default PCI settings
    [ 4503.276836] mei_me 0000:00:16.0: no hotplug settings from platform
    [ 4503.276839] mei_me 0000:00:16.0: using default PCI settings
    [ 4503.276855] snd_hda_intel 0000:00:1b.0: no hotplug settings from platform
    [ 4503.276863] pcieport 0000:00:1c.0: no hotplug settings from platform
    [ 4503.276871] pcieport 0000:00:1c.2: no hotplug settings from platform
    [ 4503.276904] iwlwifi 0000:02:00.0: no hotplug settings from platform
    [ 4503.276912] ehci-pci 0000:00:1d.0: no hotplug settings from platform
    [ 4503.276917] ehci-pci 0000:00:1d.0: using default PCI settings
    [ 4503.276933] lpc_ich 0000:00:1f.0: no hotplug settings from platform
    [ 4503.276938] lpc_ich 0000:00:1f.0: using default PCI settings
    [ 4503.276956] ahci 0000:00:1f.2: no hotplug settings from platform
    [ 4503.276961] ahci 0000:00:1f.2: using default PCI settings
    [ 4503.276976] pci 0000:00:1f.3: no hotplug settings from platform
    [ 4503.276980] pci 0000:00:1f.3: using default PCI settings
    [ 4503.277590] pci_bus 0000:01: Allocating resources
    [ 4503.277619] pci_bus 0000:02: Allocating resources
    [ 4503.277652] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
    [ 4503.277669] pci 0000:00:00.0: no hotplug settings from platform
    [ 4503.277673] pci 0000:00:00.0: using default PCI settings
    [ 4503.277686] i915 0000:00:02.0: no hotplug settings from platform
    [ 4503.277690] i915 0000:00:02.0: using default PCI settings
    [ 4503.277703] pci 0000:00:03.0: no hotplug settings from platform
    [ 4503.277711] xhci_hcd 0000:00:14.0: no hotplug settings from platform
    [ 4503.277716] xhci_hcd 0000:00:14.0: using default PCI settings
    [ 4503.277731] mei_me 0000:00:16.0: no hotplug settings from platform
    [ 4503.277736] mei_me 0000:00:16.0: using default PCI settings
    [ 4503.277751] snd_hda_intel 0000:00:1b.0: no hotplug settings from platform
    [ 4503.277759] pcieport 0000:00:1c.0: no hotplug settings from platform
    [ 4503.277767] pcieport 0000:00:1c.2: no hotplug settings from platform
    [ 4503.277801] iwlwifi 0000:02:00.0: no hotplug settings from platform
    [ 4503.277809] ehci-pci 0000:00:1d.0: no hotplug settings from platform
    [ 4503.277814] ehci-pci 0000:00:1d.0: using default PCI settings
    [ 4503.277830] lpc_ich 0000:00:1f.0: no hotplug settings from platform
    [ 4503.277835] lpc_ich 0000:00:1f.0: using default PCI settings
    [ 4503.277852] ahci 0000:00:1f.2: no hotplug settings from platform
    [ 4503.277857] ahci 0000:00:1f.2: using default PCI settings
    [ 4503.277871] pci 0000:00:1f.3: no hotplug settings from platform
    [ 4503.277875] pci 0000:00:1f.3: using default PCI settings
    [ 4503.287972] Bluetooth: hci0: read Intel version: 370710018002030d00
    [ 4503.551878] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
    [ 4503.596787] usb 2-5: new high-speed USB device number 5 using xhci_hcd
    [ 4503.633858] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 4503.755400] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
    [ 4503.797807] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0bda:5752)
    [ 4503.801045] input: Integrated_Webcam_HD as /devices/pci0000:00/0000:00:14.0/usb2/2-5/2-5:1.0/input/input16
    [ 4503.943676] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
    [ 4506.058296] dell_wmi: Unknown key e00e pressed
    [ 4507.048423] wlan0: authenticate with c0:25:06:84:57:f0
    [ 4507.051164] wlan0: send auth to c0:25:06:84:57:f0 (try 1/3)
    [ 4507.053766] wlan0: authenticated
    [ 4507.056205] wlan0: associate with c0:25:06:84:57:f0 (try 1/3)
    [ 4507.062403] wlan0: RX AssocResp from c0:25:06:84:57:f0 (capab=0x431 status=0 aid=1)
    [ 4507.065241] wlan0: associated
    [ 4507.065268] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 4812.948936] usb 2-2: new high-speed USB device number 6 using xhci_hcd
    [ 4813.124097] hub 2-2:1.0: USB hub found
    [ 4813.124371] hub 2-2:1.0: 4 ports detected
    [ 4813.392831] usb 2-2.2: new full-speed USB device number 7 using xhci_hcd
    [ 4813.477901] usb 2-2.2: ep 0x85 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 4813.495517] input: Burr-Brown from TI USB Audio CODEC as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.2/2-2.2:1.3/0003:08BB:2902.0003/input/input17
    [ 4813.495657] hid-generic 0003:08BB:2902.0003: input,hidraw2: USB HID v1.00 Device [Burr-Brown from TI USB Audio CODEC ] on usb-0000:00:14.0-2.2/input3
    [ 4813.515300] usbcore: registered new interface driver snd-usb-audio
    [ 4813.546263] usb 2-2.3: new full-speed USB device number 8 using xhci_hcd
    [ 4813.648070] logitech-djreceiver 0003:046D:C52B.0006: hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2.3/input2
    [ 4813.699821] usb 2-2.4: new high-speed USB device number 9 using xhci_hcd
    [ 4813.700997] input: Logitech Unifying Device. Wireless PID:1028 as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.3/2-2.3:1.2/0003:046D:C52B.0006/0003:046D:C52B.0007/input/input18
    [ 4813.701200] logitech-djdevice 0003:046D:C52B.0007: input,hidraw4: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1028] on usb-0000:00:14.0-2.3:1
    [ 4814.121899] ax88179_178a 2-2.4:1.0 eth0: register 'ax88179_178a' at usb-0000:00:14.0-2.4, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:24:9b:0a:27:f6
    [ 4814.121931] usbcore: registered new interface driver ax88179_178a
    [ 4814.442429] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 4817.483762] ax88179_178a 2-2.4:1.0 eth0: ax88179 - Link status is: 1
    [ 4817.485665] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 6509.605763] usb 2-2: USB disconnect, device number 6
    [ 6509.605773] usb 2-2.2: USB disconnect, device number 7
    [ 6509.660447] usb 2-2.3: USB disconnect, device number 8
    [ 6509.692281] usb 2-2.4: USB disconnect, device number 9
    [ 6509.692540] ax88179_178a 2-2.4:1.0 eth0: unregister 'ax88179_178a' usb-0000:00:14.0-2.4, ASIX AX88179 USB 3.0 Gigabit Ethernet
    [ 6509.692573] ax88179_178a 2-2.4:1.0 eth0: Failed to read reg index 0x0002: -19
    [ 6509.692584] ax88179_178a 2-2.4:1.0 eth0: Failed to write reg index 0x0002: -19
    [ 6509.721655] ax88179_178a 2-2.4:1.0 (unregistered net_device): Failed to write reg index 0x0002: -19
    [ 6509.721669] ax88179_178a 2-2.4:1.0 (unregistered net_device): Failed to write reg index 0x0001: -19
    [ 6509.721678] ax88179_178a 2-2.4:1.0 (unregistered net_device): Failed to write reg index 0x0002: -19
    [ 6511.071805] PM: Syncing filesystems ...
    [ 6511.077462] atkbd serio0: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0).
    [ 6511.077473] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
    [ 6511.085453] atkbd serio0: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0).
    [ 6511.085464] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
    [ 6511.087129] done.
    [ 6511.087139] PM: Preparing system for mem sleep
    [ 6511.087676] Freezing user space processes ... (elapsed 0.001 seconds) done.
    [ 6511.089183] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
    [ 6511.090294] PM: Entering mem sleep
    [ 6511.090393] Suspending console(s) (use no_console_suspend to debug)
    [ 6511.090786] wlan0: deauthenticating from c0:25:06:84:57:f0 by local choice (Reason: 3=DEAUTH_LEAVING)
    [ 6511.100925] cfg80211: Calling CRDA to update world regulatory domain
    [ 6511.101532] sd 2:0:0:0: [sda] Synchronizing SCSI cache
    [ 6511.101598] sd 2:0:0:0: [sda] Stopping disk
    [ 6511.720807] PM: suspend of devices complete after 629.628 msecs
    [ 6511.734165] PM: late suspend of devices complete after 13.343 msecs
    [ 6511.734991] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
    [ 6511.735113] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
    [ 6511.747808] PM: noirq suspend of devices complete after 13.629 msecs
    [ 6511.748271] ACPI: Preparing to enter system sleep state S3
    [ 6511.749033] PM: Saving platform NVS memory
    [ 6511.749584] Disabling non-boot CPUs ...
    [ 6511.749628] intel_pstate CPU 1 exiting
    [ 6511.751130] kvm: disabling virtualization on CPU1
    [ 6511.752157] smpboot: CPU 1 is now offline
    [ 6511.752650] intel_pstate CPU 2 exiting
    [ 6511.754091] kvm: disabling virtualization on CPU2
    [ 6511.754112] smpboot: CPU 2 is now offline
    [ 6511.755147] intel_pstate CPU 3 exiting
    [ 6511.756491] kvm: disabling virtualization on CPU3
    [ 6511.857520] smpboot: CPU 3 is now offline
    [ 6511.860099] ACPI: Low-level resume complete
    [ 6511.860168] PM: Restoring platform NVS memory
    [ 6511.860682] Enabling non-boot CPUs ...
    [ 6511.860725] x86: Booting SMP configuration:
    [ 6511.860726] smpboot: Booting Node 0 Processor 1 APIC 0x1
    [ 6511.873161] kvm: enabling virtualization on CPU1
    [ 6511.875384] Intel pstate controlling: cpu 1
    [ 6511.875441] CPU1 is up
    [ 6511.875462] smpboot: Booting Node 0 Processor 2 APIC 0x2
    [ 6511.887813] kvm: enabling virtualization on CPU2
    [ 6511.890055] Intel pstate controlling: cpu 2
    [ 6511.890104] CPU2 is up
    [ 6511.890121] smpboot: Booting Node 0 Processor 3 APIC 0x3
    [ 6511.902450] kvm: enabling virtualization on CPU3
    [ 6511.904715] Intel pstate controlling: cpu 3
    [ 6511.904763] CPU3 is up
    [ 6511.910077] ACPI: Waking up from system sleep state S3
    [ 6511.930462] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 6511.930469] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
    [ 6511.930713] PM: noirq resume of devices complete after 11.834 msecs
    [ 6511.931215] PM: early resume of devices complete after 0.474 msecs
    [ 6511.931290] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
    [ 6511.931308] usb usb2: root hub lost power or was reset
    [ 6511.931310] usb usb3: root hub lost power or was reset
    [ 6511.932049] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
    [ 6512.019117] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
    [ 6512.030458] sd 2:0:0:0: [sda] Starting disk
    [ 6512.143743] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 6512.143995] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 6512.237297] usb 1-1: reset high-speed USB device number 2 using ehci-pci
    [ 6512.350707] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 6512.353607] ata3.0

    Update: I mucked about more after making this post; I installed gnome-alsa-mixer and checked the "internal mic" option and "Auto-Mute mode" (both were off), after this my headphone output works again, and does the built-in microphone (!)
    I have no idea how I ended up in this "broken" situation, or even what this option does, or how to use it without gnome-alsa-mixer (I had to install 15 packages to get this, as I normally don't use gnome)... Sound on Linux still seems no better than when I started using it 15 years ago :-( (I spent about 5 hours on this...)

  • My ipod 5th gen won't change volume when headphones are plugged in, but when they are not I can change the volume on the speaker.  How do I fix this?

    My ipod 5th gen won't let me adjust volume when headphones are plugged in, but when they are not I can adjust the volume on the speaker.  How do I fix this?

    Try a hard reset of the Nano. To do this, press and hold both the Select (Center) and Menu buttons together long enough for the Apple logo to appear.
    I assume you have double checked to make sure you are plugging the headset all the way in meaning the white part of the headset is flush with the body of the Nano?
    B-rock

  • Ipod Nano 7 - No sound comes out of the headphones, and i tried different headphones... Can you help? What shall i do?

    Hello ! No sound comes out of my ipod nano 7. I tried different headphones, all working on other players, but nothing comes out of the ipod nano. Of course I turned the volume up and made sure to press on play... Anybody to help me out? Thanks a lot !

    The jack on the Nano is very tight when it is new. Push the headphones all the way in until the plastic on the headset jack is flush with the body of the Nano.

  • Headphone jack is broken! [T500]

    I'm always using headphones while on my computer.  Earlier today, my headphone jack no longer works.  Even when the headphones are plugged in, audio only comes out of the speakers.  At first I thought it was an audio driver problem so I uninstalled and reinstalled the driver.  It still wasn't working on my Windows 7 drive.  So I then swapped in my XP drive and the audio still wasn't working.  It won't work on my Ubuntu drive either.  I blew some compressed air into the jack but it didn't fix the problem.  Obviously it's an internal hardware problem.  I'm out of my warranty (bought in June 2009, only got a 1-year warranty).  I'm a college student and this is my only computer.  How much will it cost for my laptop to get fixed?  Is it possible for me to make the repair by myself?  Please help.  I'm very distraught.

    if it is indeed the headphone jack that is the issue, then it is very difficult to repair it. I suggest you get a usb sound card or a expresscard sound card (the latter is better since it sits flush in the system). 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Headphone jack not working on new Macbook Pro what is causing this?

    My 17 inch Macbook Pro is less than two weeks old. The headphone jack does not recognize the headphones about half the time. This occurs with several pairs of headphones and yes, they are ther right size. This is really frustrating on a brand new 3500 dollar machine. What is causing this? It almost seems as if the headphones cannot make contact due to the fact that the connection is too far recessed. I don't live near an Apple store so dealing with this is going to be a P.I.T.A. Anyone have any ideas on how I might fix this issue? Thanks!

    Hi, and thanks for your reply. I didn't have a red light emitting from the jack. I had already checked in the sound preferences to make sure the settings were correct. The headphones were not being recognized. This was not working with several differing sets of headphones. I made a phone appt. with Applecare. The laptop PRAM was reset and it works. There is still a bit of a delay when I plug in the headphones before they are recognized and I do feel the port is just a bit "off" as the no headphones plug all the way in. They seem to just sit almost flush but, not quite. However, resetting it resolved the issue to a satifactory level. Applecare said the issue was that not enough power was getting to that function on my laptop. They gave me the case number and I can use it if I have any further problem when I take the laptop in with me to any Apple service center. I was quite satisfied with how this was handled by Apple and if I have anymore issues will follow up.
    I love  this laptop but, even though this is working now I do feel that port is somewhat recessed a bit much.
    I also want to add that this is my first Mac and despite having had this issue I was extremely impressed with the Applecare call that I got to help resolve this. One of the reasons I went with a Mac was the reputation for service Apple has. I was fed up with Sony to the hilt. I was glad I went with this Mac despite the headphone issue because had I still been with Sony, I'd have been give a major run around to deal with this issue. So far, Apple has tried everything possible to help me with this and assured me should I have any further issue they will immediately resolve it or give me a new machine. WAY better than dealing with Sony! I do not regret going with this MAC headphone issue or not!

  • Headphone jack problems.

    I bought the new iphone 4s Saturday and I just tried using my headphones with it. I tried my Bose headphones first and they worked for a little bit and then the music started playing through the speaker. I tried them again with the Bose headphones and it didn't play at all even if I held them in. I tried the headphones that came with my iphone and they only work if I hold them in. Weird. I haven't damaged anything on it, do I don't understand why it's not working. Any help?

    Might not be plugged in all the way. Give it a little more muscle until the plug sits flush with the phone. Shine a flashlight and check for debris just in case first.

Maybe you are looking for