FM2-A55M-E33 : stop working suddenly : 2 bips

Hi,
my motherboard FM2-A55M-E33 suddenly stopped to work : after switching on, the display remains black, keyboard (logitech G15) doesn't seems powered on, nothing boot but the buzzer produces 2 quick bip each ~10s. This config was working well for 2 months but i had to reboot this morning, but no way to boot again !
I cannot find explanations on these bips meaning and don't know what to do now, i try to removed as many component as possible (keyboard, harddisks) without success; could someone help me with this ? Any suggestion will be appreciated.
Do you have a way to do a hard reset of the BIOS ?
Board: FM2-A55M-E33
Bios: 10.1 (according to User's Manual)
VGA:  APU A4-5300
PSU: 350W
CPU : APU A4-3400
MEM: 1x4Go GSkill DDR3

Quote
Do you have a way to do a hard reset of the BIOS ?
  hard reset? Try that: >>Clear CMOS<<
Quote
Bios: 10.1 (according to User's Manual)
  The bios version of your board is not listed in User's manual...
Quote
PSU: 350W
What 350W psu? >>Posting Guide<<
Quote
MEM: 1x4Go GSkill DDR3
What GSkill stick? >>Posting Guide<<
Try reseating cpu and retry with testing the memory stick in any mem slot one after the other.

Similar Messages

  • PCI wireless card does not work after restart - FM2-A55M-E33

    Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
    BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
    I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
    Does anyone know more about this issue?

    Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
    ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
    ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
    ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
    And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
    I am unable to find any useful information in the logs.
    Got any more suggestions?
    Thanks! (And sorry to disturb so much)

  • Bug in latest 2 bios updates for FM2-A55M-E33

    Hey guys,
    Today I tried to update my bios of my FM2-A55M-E33 to the latest version(7721vA4.zip). Once everything completed succesfully, the bios wouldn't boot anymore.
    I plugged out my 3TB hdd and it worked fine. I installed an earlier version of the bios(7721vA0.zip) and this did work with my 3TB hdd.
    So in short:
    The latest bios updates for FM2-A55M-E33 will freeze(black screen) at bios start when a 2TB+ hdd drive is plugged in.
    Namely:
    FM2-A55M-E33 (MS-7) V10.3 BIOS Release
    FM2-A55M-E33 (MS-7) V10.4 BIOS Release
    I hope you can fix this asap, especially since these are the latest updates.
    Regards,
    Henkie de Grote

    Quote from: flobelix on 24-February-13, 08:05:55
    better report to MSI: >>How to contact MSI.<<
    True, but I couldn't find an email address, couldnt see how to contact them through a form or something, and don't really want to call them if otherwise possible.
    Thx for the info anyways

  • FM2-A55M-E33 and Dual Graphics

    I purchased a MSI FM2-A55m-E33 Mainboard, AMD APU (A8-5600K), 8 GB Kingston HyperX Memory and a MSI Radeon 6670 viseo vard to do a CrossfireX budget gaming rig.
    I have 2 Problems, the memory can not be set over 1333 MHz, if I set it to 1600 in the bios after about 10 minutes of playing wow, the game closes, if I set it back to default (1333) it runs fine.
    2nd problem, when I first set up the PC, and started to set up the bios after 20 seconds the PC would restart. I had the video card plugged into the 6670 card, not onboard, this happened 2 or 3 times so I decided to plug it into the vga on the mainboard, no more resets...so I thought...hmmmmm.
    Anyway, set up the bios, logged into Windows, downloaded the drivers, set it all up for dual graphics, restarted the pc. Plugged the monitor in the 6670 (as recommended by amd) and no video, pc boots and goes into windows, but I have no video, so I plugged the monitor into the onboard video and viola, it works.
    So, next I turn off dual graphics in the Catylist software, reboot pc to just use the 6670 until I get this figured out, plug the monitor into the video card, guess what...no video again. I can only get video from the mainboard, never from the 6670 video card.
    I have been tinkering with this all weekend to no avail, its driving me nuts.
    My setup:
    MSI FM2-A55M-E33 Mainboard
    AMD APU A8-5600K (Unlocked)
    8 GB Kingston HyperX 1600 Mhz DDR3
    MSI R6670 Video Card
    Thermaltake TR2 600 watt PSU, 2X 12V Rails
    Seagate Barracuda 640 GB HD
    Lite-On DVD R/W
    P.S, I laready updated the bios to ver 10.1, it didnt fix anything.
    Any help would be greatly appreciated.

    Quote from: oozz77 on 28-November-12, 21:28:39
    I think you got the wrong card for "duel graphics".
    I'm sure it can't be higher than a 6570 model with a A8-5600 and that's why it isn't working as it should!!
    You can now only use the 6670 once you set i in the bios or simply try to exchange it for a 6570.
     Yup, what you have integrated graphics: AMD Radeon HD 7560D, recommended what you need for dual graphics: AMD Radeon HD 6570
    http://www.amd.com/us/products/technologies/dual-graphics/Pages/dual-graphics.aspx#3
     Although that RAM is primarily meant for Intel Sandy Bridge system with 1600 XMP profile it's possible it may be OK for your system but you would have been better off getting RAM for AMD system instead. When trying for 1600 did you bump up voltage from 1.5V to a bit more  like maybe 1.55 to see if it would run stable?
     Research for proper component compatibility goes a long way to eliminate problems such as what you are having.

  • External graphics card problem with fm2-a55m-e33

    I just bought the fm2-a55m-e33, everything is working fine with the board. I was planning on using my old 9600gso but when I plug it in nothing happens. Windows doesn't recognize the hardware and nothing will display out of the card.
    What is the deal?

    list full system specs, read >>Posting Guide<<

  • FM2 A55M E33 upgrade concerns.. :)

    Hi just a few questions before i buy anything..
    At the moment what I have is:
    MSI FM2 A55M E33, AMD A8 - 5600K, 2 X 2GB 1333 RAM, Deepcool GAMMAX200 Heatsink, 500GB HDD, Generic 600w PSU, Cheap Case.
    Now, I'm planning to upgrade the Video Card and RAM this week, and I don't know what to get.. But i think from what I plan I may need a new PSU and CASE.. (Will get Thermaltake Commander MS1 - this one, i think im sure)
    My budget is below $300 (VGA, RAM, CASE, PSU).
    The guy from the store told me that I would have a problem running 1600 RAMs on my FM2.. I didn't bother to ask him so I'm asking here..
    Would a Powercolor HD 7790 work on my unit?
    Im sure i would need to upgrade my PSU but how many watts should i get?
    Thanks!

    Quote from: thinkx on 14-September-13, 06:26:25
    So something liker (Kingston HyperX Memory 2 x 4gb Ddr3-1600 Cl9) should work?
    Yes
    Quote from: thinkx on 14-September-13, 06:26:25
    Would this PSU -- Seasonic S12ii-520 Power Supply 520watts S-Series -- be enough?
    Yes but I would suggest you attempt to get a unit like that but around 600W as it will give you some headroom as that one is good on both but is close on the minimum wattage so may be a little unstable over time as it ages!

  • Msi fm2 a55m e33 build problem

    Recently I helped a friend build a rig.
    The setup as follows:
    Case: cooler master elite 344 with usb 3.0
    Mobo: msi fm2 a55m e33 / amd a6 6400k richland processor
    Os: Windows 7 home premium 64-bit
    The problem after I built finish, my friend complained of no sound.
    I got her to download and install the latest system and chipset drivers but didn't help.
    Got her to download and install the latest sound drivers from the msi driver page but still didn't help.
    So I told her to check the case and she told me that there is a small black speaker that I didn't connect to the board. So I told her to connect it to jfp2 according to user manual. Still didn't work. I suppose that speaker is meant for the beep.
    As far as I know about the audio aspect of the cm case, it has a hd audio and an ac 97 plug connected together into one single plug. Tried both on jaud1 but still failed.
    Not exactly sure where the fault came from.

     

  • FM2-a55m-e33

    Hello. Issues here. 
    Running this mobo with amd A4 - 5300, 1 stick gskill ram, OZ SSD.
    I can load windows fine, but after installation it "hangs" on the "windows is preparing user environment for first time use"  the progress indicated shows the PC is not frozen, but it never makes it past this part.
    I have been told that step is were windows sets up the drivers, so wondering if it might be a driver issue.
    Also this mobo BIOS version is from 5/1/13, there are two never versions. should i try to flash the BIOS? I am not sure how though, the only file MSI hosts is an executable for the BIOS which is only useful if you can actually get into a windows desktop environment. where can i get the actually BIOS file to be used in the M-FLASHER utility within the BIOS?
    any help is appreciated, i have sunk 6+ solid hours into this already.

    Board: MSI FM2-A55M-E33 FM2 AMD A55 (Hudson D2)
    Bios:   Version 11.1
    VGA:   CPU INTEGRATED
    PSU:   BCP450-OM (Came with case)
    CPU:   AMD A4-5300 Trinity 3.4GHz (3.6GHz Turbo) Socket FM2 65W Dual-Core Desktop APU (CPU + GPU)
    MEM:  G.SKILL NS 2GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory
    HDD:  OCZ Agility 2 OCZSSD2-2AGT40G 2.5" 40GB SATA II MLC Internal Solid State Drive (SSD)
    COOLER:  STOCK
    OC: NONE
    OS: Windows 7 64bit Professional
    I don't get any errors, or BSOD. It just will not make it past the "windows is preparing user enviroment for first time use"
    I can run DOS enviorments, but i cannot get into the device manager from either windows recovery disc OR when it "hangs" at the above mentioned spot. It is frustrating.
    I have tried the following.
    Installing a video card from another computer because i have heard a video driver issue might cause it to hang.
    I have swapped out power supplys with another known working PSU.
    I have dissabled all unnessisary BIOS features ex. the LAN adapter, power saver modes...
    I have reinstalled windows from a freshly formated drive multiple times.
    I have attempted to access the device manager from the command promt in windows repair disc with no success. It seems to only try run the devmgmt off of the X drive (system reserve partition) and not the D: drive (primary partiion with windows 7 instal)

  • FM2-A55M-E33 upgrade bios with richland

    Is there any way to upgrade the BIOS on my FM2-A55M-E33 with A4-4000 APU?  I don't want to have to buy a Trinity just to upgrade to the latest BIOS with Win 8.1.

    There is no reason for rma if nobody guaranteed you that your specific sample will work with Richland out of the box. That the board is able to run Richland cpus of course does not mean it will with any bios version. Vendors have boards in stock. They don't open any box so any board in stock is updated to the latest version. It is common sense a board manufactured before Richland support may not include a Richland supporting bios.
    paynej1,
    some FM2 boards will not completely work but post with Richland and allow to enter bios. Only those can be updated without a Trinity cpu. For all others you need a supported cpu or having the board flashed by a pc-shop or MSI.

  • FM2-A55M-E33 Problem

    I have bought a AMD A10 5800K Black Edition for this Mainboard, I have installed the latest bios firmware (11.5) and have hit a few problems sometimes the bios will frezze and when it boots to windows the windows boot screen frezzes but all works fine with the A4 that I have already installed
    MSI FM2-A55M-E33 Mainboard
    16gb RAM Corsair Blistix Memory
    500gb main hdd
    1tb second hdd
    dvd re-write drive
    Windows 7 Home Prem
    500w psu
    Any advice as to what the problem might be

    just recived a replacement Amd A10 cpu and the same this is happening bios locks up and when it does boot to windows i can't get passed the "starting windows" screen then the logo goes funny colours and a red stripe at the top of the screen apears
    Mainboard is FM2-A55M-E33
    Bios Version 11.5 (latest)
    Any help thanksQuote from: Svet on 04-December-14, 03:05:25
    what is your current bios version?
    how much memory sticks?
    exact models?
    2 Dimms 1866 Corsair Blistix
    what exactly?
    brand?
    model?
    PSU stats?
    Came with the case
    don't understand what you mean by all works fine with "A4"
    what is A4? and if all works fine when its installed what doesn't works then?

  • FM2-A55M-E33 don't boot with ATX 4-Pin Power Connector plug in

    I have a MSI FM2-A55M-E33 motherboard with AMD A10-5800K.
    When I boot, nothing happen, the fan start 0.10 sec, and stop.
    When I unplugged the ATX 4-Pin Power Connector, the fan run, but no video...
    I try with different power supply and memory, same problem.
    And no sound from the speaker...
    Can you help me ?
    Should I change my MB ?

    Here is my conf :
    Board: MSI FM2-A55M-E33
    PSU : ?
    Bios: ?? (no Video output)
    VGA:   AMD Radeon™ HD 7660D (include on MSI FM2-A55M-E33)
    CPU : AMD A10-5800K
    MEM : SPECTEK 2133 2x4gb DDR3 1333 CL9
    HDD: SANDISK SSD 60GB
    When I boot, nothing happen, the fan start 0.10 sec, and stop.
    When I unplugged the ATX 4-Pin Power Connector, the fan run, but no video...
    I try with different power supply and memory, same problem.
    And no sound from the speaker...
    Can you help me ?
    Should I change my MB ?
    Sorry, I have no info about my PSU. I have both 24 and 4 Pin Poweer Connectors...
    No OC, just standard config of the Board...

  • FM2-A55M-E33 Bios Problem

    Hello!
    I recently bought a system with below Specs.
    Main Board: MSI FM2-A55M-E33
    Bios Version: 11.1
    Video Card: None
    PSU:  Thermaltake 480w
    CPU: AMD A6-6400k
    Memory: 1 x HyperX Blu 4GB 1600
    SSD/ HDD: WD Green 500GB
    CPU COOLER: DeepCool Gammaxx300
    Operating System: Win7 x64
    after assembeling and turning on power and entering Bios, through Utility Tab > M-Flash upgraded the Bios from 11.1 to current version 11.5
    Now that i've installed win7 x64 and want to OC, i see "CPU Ratio" and "Base Freq" is locked! while my CPU is Black Edition!
    What's the problem? Is it normal?!!!
    Is it because of upgrading bios using Richland CPU?

    Quote from: flobelix on 01-June-14, 04:20:03
    Did changing multiplier work before the update? Have you tried +/- keys to alter settings?
    Thanks for response
    No i didn't check it before Bios Update
    Unfortunately yesterday my MB didn't boot and seems bios is damaged. I sent it for warranty, will comment what happened.

  • My iPod nano 6G stop working suddenly; After i reset it and even afetr put it in "stand by" mode by accessing deagnostic mode, it is still not working; Now i can access it sometimes (the main screen), but is not playing and is too slow. How can i fix it

    My iPod nano 6G stop working suddenly; After i reset it and even afetr put it in "stand by" mode by accessing deagnostic mode, it is still not working; Now i can access it sometimes (the main screen), but is not playing and is too slow. How can i fix it

    If you do not find a solution in the iPod nano (6th generation) - User Guide, suggest that you call AppleCare if still under warranty or take a trip to your local Apple Store or AASP.

  • Deploying Stop Working Suddenly

    hi,
    i have MDT 2013 with 4 Deployment shares, one of the deployment shares stop working suddenly "windows 7 deployment share" . when i start the network boot i can see a list of boot image but when i choose that image it gives me the windows loading
    screen for ever and not start the deployment process. other boot images is working fine
    can anyone help me to solve this problem
    thanks 
    Sameh Ismail System Administrator

    @Keith:
    Why are you always proposing your 'further questions' as answers? That's not adequate in any way!
    Especially as a 'Moderator' you should know better, I really dislike this and I am quite sure that I am not on my own with this opinion.
    http://social.technet.microsoft.com/wiki/contents/articles/4865.whether-or-not-you-should-self-propose-an-answer-in-an-msdn-or-technet-forum.aspx
    It is pretty obvious from the post that this happens while loading WinPE, what is there to misinterpret?
    Are you using different WDS servers for your sites?
    If yes, try to remove the boot image from the 'Broken' one and re-import it.
    Comparing checksums is never a bad idea in such a scenario.

  • My iPad stop working suddenly i see black screen only pressing the home? and sleep button dose not solve the  problem please help?

    My iPad stop working suddenly i see black screen only pressing the home and sleep button dose not solve the problem please help ?

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen, not responding, how to fix
    http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    Black or Blank Screen on iPad or iPhone
    http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Home button not working or unresponsive, fix
    http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
    Fixing an iPad Home Button
    http://tinyurl.com/om6rd6u
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

Maybe you are looking for