FM2-A75MA-E35 with A10-5800K will not POST

This is my first post, but not my first build. When I power on the processor, the CPU fan and the case fan start, but I have no signal or power at any of the rear panel connections. As a result, I have no keyboard, mouse, or monitor. Is it likely that I have a bad motherboard?
Here are the specs:
AMD A10-5800K APU (new): s/n 9L33252B30018
MSi FM2-A75M-E35 Motherboard (new): s/n 601-7721-010B1307193315
The board is MS-7721 version 1.3
Any suggestions would be appreciated. Thanks.
Bob

I removed motherboard and CPU, examined the CPU installation prior to removal from its socket. All looked OK while in the socket - no misalignment and no bent or exposed pins. I then removed the CPU from the socket and examined again. It is in perfect physical condition.
Next I cleaned the old thermal paste from both the heat sink and the CPU, reapplied clean paste, and then re-installed the CPU. The CPU dropped into the socket with zero insertion force. I re-installed the heat sink and fan, installed the memory, then connected the power cables and fan switches.
When powered up and run for 3-4 minutes, the processor heat sink is warm, so I think the CPU may be working, or at least it has power. There were no beeps on start up. I again tried to connect mouse and keyboard, and tested the USB ports for a signal. No change from the condition of yesterday - still no light on the optical mouse or keyboard, and no connection to the USB ports on the back I/O panel.
I can purchase another power supply locally if that seems to be the trouble, but the motherboard and CPU apparently have power. What else can I try?

Similar Messages

FM2-A75MA-E35 with A10-5700, CPU temperature at 85c!!! Is this normal?

I just put together the system, see below (no overclocking), and using AMD Overdrive for stability test with CPUID software to monitor temperature:
FM2-A75MA-E35
A10-5700 Boxed using stock fan
Patriot signature DDR3 8G 1333mhz
1T WD Greennnn..........
At room temperature about 25c
1. In BIOS, temperature after boot up jumps quickly from 25c to idle at 58c and the fan spinning at about 3200 RPM. It sounds like a small refrigerator.
2. Idle in Windows 7, CPUID displays CPU temp at 42c.
3. Stability test using AMD Overdrive with all components selected, CPU temp shoots up to MAX at 85c!!!!! average about 75c!
I found out that A10-5700 maximum temperature is 71c. I double check everything (connections and fan) and update the BIOS then run it again, the same results show up.
Is there anything wrong?
Darth

Quote from: darth_juon on 13-February-13, 02:03:41
Thanks Joe and wlahdone,
I am currently waiting for the new A10-5700 CPU.
Have you try the last BIOS version 1.7 (1/29/2013) with Update CPU AGESA code?
I also had BIOS problem.
BIOS version that come with the board, It hung when I try to save changes and exit. This issue has been reported by another user.
BIOS version 1.5, Solved the save changes problem.
*Both versions have the same funny temperature reading.
I don't want to spend much time with this, I only need a simple PC or two, just driving to the PC store gas cost a lot of money these days.
I had the same issues when i ve bought it - the freezing at save.
It seems the board comes with BIOS 1.2 which is bugged ,it simply takes the OC settings at the first boot and overclocks the FSB ,this giving the freezing most probable.
Clearing CMOS or pressing F6 and then F10 in BIOS solves the problem.
I am on BIOS 1.5 and it s ok.
The HW Monitor reports the 0 Celsius for the onboard video ,but i really don t care.
I ve thrown at it Windows XP ,Windows 7 ,Open SUSE 12 ,Linux Mint and Simply Mepis.
They all worked fine in spite of the little 5300 APU that i use for this HTPC , it runs everything
I ve made myself a toy that plays 1080p and routes in same time ,a pleasure to see it in action
After AMD releases the new APU-s ill switch from a AM3+ rig to one of these.
The board BIOS reports nice temps if you use a proper cooler.

FM2-A75MA-E35 with Samsung 43" Plasma TV

Good day
Can some please assist me, when I connect my PC to my Samsung 43" HD ready plasma via HDMI, when the PC starts up the start up screen is half cut off and the TV resolution drops to 1280*760 if I try to boot in to bios is does not show completely on the screen and if I click on anything I get a crash screen and the PC freezes.
In windows 7 Ultimate 64 bit if i set resolution higher than 1280*760 everything becomes very blurry but the TV resolution changes back to 1920*1080*60
PC Setup
550 Watt ARMAGEDDON PSU
MSI FM2-A75MA-E35 MOTHERBOARD
A10 6800K CPU
2 X 4GB DDR3 1333MHZ RAM
WD 1TB SATA3 HDD
SEAGATE 2TB SATA2 HDD
SAMSUNG PS43F4000 43" HD READY PLASMA TV
Also with CPU-Z the highest clock speed i have reached is 2175MHz with OC genie enabled, can overclock trough boot up bios because of above problem dont like over clocking through windows CLick Bios II
BIOS VER 2.2
Any ideas ??? please anybody
Thanks IA

Something seems to be really wrong with your setup. The standard frequency of a 6800K is already 4100Mhz and you say max would be 2175Mhz (assuming you mean under load). Try clearing cmos and retry: >>Clear CMOS Guide<<

M-Flash BIOS Update Failure on New But Working FM2-A75MA-E35 with AMD A4 5300

The BIOS had minor issues at the included rev. 1.2, so I downloaded 1.5 to update. From a FAT32 USB flash drive, the BIOS download file was selected and started programming. Then the monitor went black and that was the end. There is no response, and no video at all.
Looking around for help, I note that the msi site "bios-note" (which I am prevented from linking to) seems rather dated: I have another of these boards and have looked and looked, but I still do not know whether the BIOS is Award or AMI, and I have not had a floppy drive in a computer for a decade. Is recovery even possible without video? Now what do I do?

Thanks for your help.
OK and done on informative signature.
OK and done on clearing CMOS.
Quote from: Svet on 15-January-13, 12:53:04
about recovery place desired BIOS file which you want to recover over USB key FAT/FAT32 formatted,
then turn on PC and press Ctrl+HOME
OK and done on Ctrl+HOME attempt: By observation, almost nothing happens.
Front power LED comes on, fans come on, DVD writer comes on, keyboard does have a brief reset, but USB devices show almost no activity at all, except for a tiny blip when power first comes on. Ctrl+HOME causes no apparent change.
What now?

M-Flash, FM2-A75MA-E35, System is not reboot or taking long time

Hi,
I have FM2-A75MA-E35 with A10-5700.
Several days ago, I downloaded a ZIP file of BIOS version 1.7 from MSI. After extracted, it was the same version 1.5 (.150 extension), but with older version of .EXE compared to my previous BIOS version 1.5 download.
After the flash screen ended, the system was not reboot almost right away like my previous 1.5 flashed, but with blank screen, fan running fully speed, and both HDD LED and Power LED lite up. About a minute late, I pressed Power with not respond then Reset also with no respond. Several seconds later, the system rebooted and Windows loaded. Later, I flashed the system back to previous 1.5 and everything seemed to be OK. Yesterday, I checked MSI site and saw that the actual 1.7 BIOS is up, I am thinking about flashing again.
Here are my questions:
What is going on after the flash screen ended?
Is it save to 1) press power or 2) reset button or 3) pull the plug after the flash screen ended, If the system is not reboot or responding for about a minute?

I flashed it the same way that I did with the early weird 1.7 version and it was working.
After flash progress bar completed, it took about less than 5 seconds, the system rebooted twice with all the LEDs turn on and off and windows loaded. I rebooted and went into the BIOS which shown version 1.7.
The scary thing was when I was in the BIOS setting the clock, the screen went blank for about a second once and sometime blinking , and it seemed to do that on the clock setting screen, not the main screen. I think this might related to graphic buffering and programing.
I hope this is normal for this UEFI BIOS and not turns into a brick.
Please, let me known that if you think this is normal or not.
Thanks,

Cpu-nb voltage not changing for FM2-A75MA-E35

I have a FM2-A75MA-E35 with a A8-5600k amd cpu and I'm trying to increase the cpu-nb voltage. According to AMD overdrive its at 1.1875 and I'm trying to increase it but any voltage I select in bios is completely ignored for some reason. I even tried with the 1.33 beta bios. How do I adjust the voltage? Do I need a special program to accurately monitor the cpu-nb voltage or is it just not adjustable?

OK i tried the one memory stick in the first DIM everything powers on but it is not booting from the harddrive ive tried getting into the BIOS but it just goes black if i let it boot up this is what i get
EFI Shell version 2.31 [4.654]
current running mode 1.1.2
Device mapping table
fs0 :HardDisk - Alias hd13a65535a1 b1k0
PciRoot(0x0)/Pci (0x11)/Sata (0x0,0x0)/HD ( 1,MBR, 0x6583ff11, 0x32800,0x3a353000)
b1k0 :HardDisk - Alias hd13a65535a1 fs0
PciRoot(0x0)/Pci (0x11)/Sata (0x0,0x0)/HD ( 1,MBR, 0x6583ff11, 0x32800,0x3a353000)
b1k1 :BlockDevice - Alias (null)
PciRoot(0x0)/Pci (0x11)/Sata (0x0,0x0)
Press ESC in 1 seconds to skip startup.nsh, any other key to continue
Shell>_
I dont know what to do from here thanks again.

[SOLVED] FM2-A75MA-E35 A10-5800K no Max Turbo

Hello, I have a MSI FM2-A75MA-E35 motherboard with the 1.41 Beta Bios & AMD A10-5800K with DDR3 1600Mhz & Windows 8 Pro. I did the factory reset by hitting F6 to go back to stock bios, now when I put Intel XMP enable on then save the setting. when I boot into Windows 8 Pro the A10-5800K show the processor 3.80ghz as Max Speed which is normal, when I encode a video it run at 3.95ghz but not at 4.2ghz. all I did in the setting is enable Intel XMP & that it. I have not touch anything else, Max Turbo is in auto.

Thanks for reporting back!

New motherboard (FM2-A75MA-E35) deliverd with Bios of other Mobo (FM-2A75IA-E53)

I bought the FM2-A75MA-E35, i got a box with this model on and it's indeed a micro atx Mobo
Well, i builded my New HTPC but got since i started building it i got multiple resets of the pc (just power off-on, in windows kernel power 41 error).
After 2 days of troubleshooting, changing PSU, memory, SSD, ... I wanted to update the Bios from v2.0 to v2.1, I however got the error that my board was not supported, after looking in tools like CPU-Z i found out that my Mobo reported itself as FM-2A75IA-E53, an ITX Mobo, this also explains why I've an option in the bios for wireless and Bluetooth, which the FM-2A75IA-E53 has, but the FM2-A75MA-E35 hasn't.
So it seems like MSI flashed the bios of another Mobo on mine in the factory? And could this explain my random reboots?
Any suggestion other then getting it back to the shop?

This thread can be closed. MSI USA send me a special BIOS to force flash.

FM2-A75MA-E35/A10-6800K/Radeon HD8670D - cant load graphics driver

I'm building a new HTPC machine (specs below). OS installed fine. Boots with generic Microsoft drivers. Tried to install chipset drivers that came with mobo. The AMD catalyst control center tries to install the graphics driver (13.350.1005.0000 Beta). The screen flickers off once, then back on, then off again never to return. I'm seeing talk about flashing the BIOS with a cheap trinity core then flashing with my Richland core. I need expert advice on how to fix this. Thank You
FM2-A75MA-E35 motherboard (MS-7721 Ver:1.3)
A10-6800K/Radeon HD8670D
2x2GB G.SKILL 1600
Windows 8.1 64 bit
BIOS Ver 1.5
480W power supply
Samsung monitor on VGA

i had the same problem in last week, but i didnt buy a new processor, my bios just dont let me do anything so, i put a booteable usb of windows 7 and i booting the usb from bios and ignore the message to actualize to richland. Then i could install windows 7 ultimate 64bits and download the new BIOS driver. And that as you make so easy you just need to copy the ".exe" driver bios and put in a usb free. Start program, upgrade bios, reboot, and finish! you have richland v2.2 or something and you can run APU A10 6800k with no problems =)

Two issues with FM2-A75MA-E35

Hi there
1- In the uefi bios startscreen it gives the correct board (FM2-A75MA-E35) and V1.2
If i look at the board itself it reads MS-7721 Ver 1.3 is this correct?
2- After booting into uefi, the moment I enter the save config menu the mouse freezes. Hitting F10 instead does the trick.
Changing parameters in bios with clickbios works well.
Current bios version V1.2
Thanks,

7721 is correct but not as precise:
http://www.msi.com/service/search/?kw=7721&type=product
Try updating the bios:
http://www.msi.com/product/mb/FM2-A75MA-E35.html#/?div=BIOS
>>Use the MSI HQ Forum USB flasher<<

FM2-A75MA-E35 & 2133Mhz RAM

Hi guys, reading the spec data of the FM2-A75MA-E35 mainboard, i can see:
Supports two unbuffered DIMM of 1.5 Volt DDR3 1066/1333/1600/1866/2133*(OC) DRAM, 32GB Max
If i buy a kit of 2133Mhz RAM, can i set this frequency in the BIOS? Or better, does exists in the BIOS the "2133Mhz" setting field?
Thank you

Quote from: caml light on 03-November-12, 08:50:56
Not correct! The graphic section of AMD APU's take a nice performance boost with 1600+Mhz RAM, as you can see here:
http://hexus.net/tech/reviews/cpu/46073-amd-a10-5800k-trinity-needs-faster-ram/
So, do you confirm that this mainboard has a FSB/DRAM ratio to set RAM at 2133Mhz keeping the CPU at stock speed?
Thank you!
The mainboard pdf manual 7721v1.0 shows that a 'DRAM Frequency' setting is in the BIOS. The specs say it supports up to 2133 OC'd RAM speed, so presume the 2133 setting is available. Also, 2133 is not guaranteed as the CPU's IMC may not be able to handle or support it. In that review, if I read it right, they OC'd the GPU as well as the RAM in those tests. Do some tests for yourself at 1866, and at 2133 if they will run at that. In a real world application, I doubt seriously any actual visual difference will be noticeable.
Unless someone chimes in that has this mainboard to confirm the 2133 setting or not, recommend to contact MSI Technical and ask them.
>> How To Contact MSI <<

AMD 760K doesn't work in - FM2-A75MA-E35

Hey guys, I just got this motherboard and found out that the CPU isn't compatible with the board. I've flashed it with the latest Bios (I happened to have a Trinity CPU spare) so it's now on 2.1 and still nothing. I've tried to go to the MSI support site but when I log in and try and do anything I get prompted to update my profile and then when I do that I get some weird error page (and the same thing happens when I try to create a new account).
I was just wondering if anyone has had similar issues with the CPU and if they have a work around or if there are any beta Bios updates etc.
Many thanks!

Quote from: Svet on 31-July-13, 17:31:54
its not in the QVL list: http://www.msi.com/product/mb/FM2-A75MA-E35.html#/?div=CPUSupport
That CPU support list only goes up to BIOS 1.5 so it's out of date as of Dec. 2012 and doesn't show any Richland being supported even though 2.0-2.1 BIOS supports Richland CPU's.
It could be that since that CPU was only released last month that it will need a more recent BIOS update for support. You would need to contact MSI regarding that though as us folks here in the forum really wouldn't know for sure at this time.

Issues attempting to flash 2.0 BIOS on FM2-A75MA-E35

OK, so I'm planning to put a Richland APU into my FM2-A75MA-E35 as soon as these come out. In preparation for this, I've attempted to flash my BIOS to 2.0, which did not work.
Some background information, I've flashed the board before without issues, up to version 1.8. The process to flash 2.0 is entirely different now, in that you need to boot from a bootable usb stick, and then run E7721V20.exe.
This is what I did. It then went through some checks which passed fine, asked me to confirm whether I really wanted to flash the BIOS, to which I answered Y, it showed the message that it is now starting to flash the BIOS, and that's it.
It then remained in this state for a good hour before I finally drew the conclusion that this isn't doing anything. Even though it said not to switch it off while flashing the BIOS, it seemed to be my only option. I did, and luckily, all was working as previously, running version 1.8.
In short, the flashing program didn't actually do anything.
I am very reluctant to make another attempt at this point in time, because I'd much rather have the board in version 1.8 for the time being, than not have it work at all.
Is there anything I could have missed? Is there any way in which I can successfully flash my board to 2.0, so that I can later use a Richland APU in it?
Any help with this is appreciated!

I've done another search on the 1.8 BIOS and I can't find anything concerning Richland support. The description was just a generic "BIOS Update", whereas the 2.0 description is:
- Update CPU ID.
- Support Richland CPU.
To me, it looks like you need the 2.0 BIOS for Richland Support. If anyone could point me to any sources that the 1.8 BIOS already supports Richland APUs, I'd appreciate it. For now, I'll stick to my belief that you do need 2.0, until I've got evidence to the contrary.
Quote from: flobelix on 09-May-13, 20:50:34
Version 2.0 for FM2-A75MA-E35 like all Win8 bios versions for AMD boards currently can't be flashed with the forum tool. It's only possible by MSI's (risky) way.
And you can't even use M-Flash, like you can for all the 1.x versions. The only way to flash 2.0 seems to be to boot into DOS from a USB stick and then run the executable supplied by MSI. Will that likely remain the only way to flash to 2.x?
Quote from: florinbss2 on 09-May-13, 22:44:31
I did the update and it worked. But I have an annoying problem. When activating Cool'n'Quiet in the BIOS, it's not work on cooler. Change frequently but not speed CPU cooler. Any percentage would choose the speed cooler does not change. Cooler running at full speed.
Well, I was going to say that at least you managed to flash your board, but having the CPU fan run at full speed irrespective of BIOS settings doesn't sound all too good either, and you can't even flash back to 1.x now, or can you?

FM2-A75MA-E35, Less Usable Memory than installed....

I just powered up my new FM2-A75MA-E35 Mainboard with A6-5400K and 4G memory stick. Running Win 7 Ult 64.
When I used on board video, I had 3g out of 4G available. I assume the missing 1G was reserved for video use.
So I put in my ATI Radeon HD 5670 video card hoping that disabling the onboard video and using plugin video card memory would free up the missing 1G of ram.
Instead, now I have 2.9G out of 4G available.
Any help or guidance is appreciated.

F3-12800CL9D-8GBRL if i'm not mistaken are G-Skill Ripjaws (they are known to be very problematic on MSI boards Due to a DEAL with a brand-X) try some different RAM and i would suggest some from Corsair of 1.5v instead!
at most the board will dedicate with 8GB installed 2-2.5GB to the IGPU max (1.5GB if only running 4GB at the most) so it sounds more like a incompatibility due to the poor choice you have made when you bought the RAM!
if its no incompatibility then you have some VERY FAULTY RAM so its either a incompatibility or very BAD ram involved here.... i suggest you get some different ram from one of these 2 Manufacturers (Corsair & Crucial) as G-Skill cant be trusted on a MSI board as they have a very bad rep and in particular the RIPJAW skew they make!

FM2-A75MA-E35 & RAM Clocking issue

Heres my system specs
Mobo: FM2-A75MA-E35
CPU: A8 5600k (Max RAM support 1866Mhz)
Ram: GSkill RipJaws DDR3-1600 PC3-12800 & Corsair XMS3 PC3-12800
I notice in the Bios that the ram is only being detected @ DDR3-1333, I enabled overclocking to DDR3-1600 but even then the ram is still only clocked @1333 both in Bios and in windows. Is this a known issue with this board?

Quote from: flobelix on 23-December-12, 05:46:20
Nice discussion about this vga but what has this to do with the ram. This is a MSI forum and not meant for discussing Sapphire vgas.
That it is!
Quote
The person I am building the system for isnt really using teh system for gaming, more video editing.
Install a larger GB factory matched and tested RAM kit if that is the intended use of the pc, RAM performance difference between 1333 and 1600 is rather low anyway.
Quote
The new FM2 APu setups do support XMP.
I wonder what Intel will have to say about that?

FM2-A75MA-E35 with A10-5800K will not POST

Similar Messages

Maybe you are looking for