"Fn+F5" does not switch the wi-fi in G410m-mm
Hello!
"Fn+F5" does not switch the wi-fi in G410m-mm. How to make the shortcut work? All drivers and utilities are installed.
Regards,
Dmitry
skripatch wrote:
I suggest another driver for cardreader or maybe you're trying to use SDHC cards instead of SD.
I doubt that you'll be able to return it in MM after 20 September.
Due to Russian law suite after two weeks you can only return it in case of unrepaireable malfunction. If you hurry up right now you can come in time.
Thanks skripatch for your opinion!
I tried with both drivers: from the driver CD and from the site. The cards are readable in the G410 through an external USB reader. The cards are not SDHC, they are 64mb and 2gb miniSD cards in a SD adapter. I bought the G410 on September 25, not 20. Why can I "come in time right now", but not between September 20 and 25?
Regards,
Dmitry
Message Edited by di on 09-16-2008 02:45 AM
Similar Messages
-
During audio messaging the send button does not switch to a microphone after selecting a contact
During audio messaging the send button does not switch to a microphone after selecting a contact
Actually, this problem is the same as the one described in your other thread, and should be fixed as well after following the procedure described there.
-
The off button does not switch to 'hibernate' or lock when playing music.
The off button does not switch to 'hibernate' or lock when playing music. I have to hold the off button down
for a prolonged period of time to get it to switch off; have had to resort to holding the off button and the main
button simultaneously to reset but no improvement.- First try restoring the iPod from backup via iTunes.
- If problem persists, restore to factory defaults/new iPod.
- If still a problem than you likely have a hardware problem and an appointment a the Genius Bar of an Apple store is in order. -
Firefox does not fully load Barclaycard Authentication site. It loads as far as asking for certain letters in my pasword but does not load the "Submit" button so I cannot continue with my purchase and have to switch to IE8 browser to purchase anything over the internet. Any clues?
== This happened ==
A few times a week
== Couple of weeks agoYour UserAgent string in Firefox is totally messed up by another program that you installed, and Barclays doesn't know you are using Firefox 3.6.6 - it probably looks like IE 6.0 to that website.
[http://en.wikipedia.org/wiki/User_Agent]
type '''about:config''' in the URL bar and hit Enter
''If you see the warning, you can confirm that you want to access that page.''
Filter = '''general.useragent.'''
Right-click the preferences that are '''bold''', one line at a time, and select '''''Reset''''',
Then restart Firefox -
itunes 11.1.5 does not recognize the switch to 64 bit mode from 32... won't open
Is there some background story to this that might give us some clue? An error message quoted exactly? Did you just do an update?
Try starting iTunes with the shift key held down. If it starts it is probably some old plugin presenting problems. -
So only a few bucks left for the edge upgrade, decided to edge up since it gave me the option to do so, I figure why not?
Process seems to go fine until i'm in the checkout for a new device.
Tosses 'This device does not match the device ID on your original Edge Agreement. ' at me, but it's really strange because I'm using the phone I got direct from Verizon, haven't switched phones or anything.
Has anyone had this issue before?Toxicle,
I can understand how something like this can be concerning. Let's work to get to the bottom of this for you. What kind of phone were you Edging up from? Has the phone ever been replaced or removed temporarily? Just want to make sure we are getting all the facts to help with this issue.
CandiceH_VZW
Follow us on Twitter at @VZWSupport -
My iphone's screen goes black and it behaves like that it is switched off.No switches work and the power button also does not respond.The ringtone do not also respond.The only way to switch on the phone is to press home button and power button together.
Pressing the Home button and the sleep/wake or on/off button together until you see the Apple logo and then release is called a reset.
If no change after a reset, the next step is restoring your iPhone. -
Applications installed in my iTouch does not launch. the music and internet functions but the installed applications does not. tried switching it on and off, still problem persists. help...
Your only chance besides getting it serviced would be setting it up as new device:
http://support.apple.com/kb/HT4137 -
I have an iPhone 4s and have set up with my provider for voicemail. however, when called my phone does not switch to voicemail. How do I set the phone to transfer to voicemail when not answered etc?
Voicemail is a carrier feature, not a phone feature. This has to be fixed by your carrier, so contact them, as obviously, voicemail is not properly provisioned on your account.
-
Apple TV 2 does not switch automatically the video resolution (60 HZ / 50 HZ)
My apple TV streams the content from a Mac Mini. In my iTunes library are mixed content from the iTunes store. Some are 24 fps with 60 Hz and some are 25 fps with 50 HZ. All was bought on iTunes. The video resolution is set on my Apple TV to AUTO. This mens for me that my Apple TV will change the resolution by itself depending on the movie.
And this is the problem. The Apple TV does not change the resolution. It is only on 60 Hz. A lot of people has the same problem. My iPad wokrs fine and displays all movies correct.Thank you for the eplanation. What might cause that activity as the TV was off and no other HDMI was on? Only WiFi was available but nothing connecting to the apple TV.... I tried to "wake it up" with iTunes on my macbook - and it works (I was not aware of). But it could not be iTunes and it was not really "used". So it might be iPhone or iPod waking it without we want it to.
I'll check all items potentially connecting to it. Txs! -
Iphone and ipad does not find the airprint printer
After I upgraded my iphone and ipad I lost my airprint function. Ipad and Iphone does not find the airprinter. The printer is a HP Photosmart 5520, and it does work wireless with my Windows PC that is on the same nettwork.
In our case the Airprint printers could not be found after IOS upgraded to 7.1.2, all was fine before then. I have scoured the forums and many people have suffered the same problem. All the solutions given are aimed at a domestic network with just a Wireless router. They all involve restarting all the devices and rejoining the IOS devices to the wireless network. Some people have had to do it multiple times before they regained use of the printers.
In my case none of these work because I am talking about a business network with two wireless access points, several switches and a router. To prove it is the IPads I have installed Bonjour onto a Windows PC (Bonjour is the technology used by Airprint). This finds the printers perfectly so it is definitely something that was changed in the version of Bonjour on the IOS 7.1.2 that is causing all the problems.
I was hoping that Apple would release another upgrade to IOS to fix this problem but it has been several weeks so far and nothing has emerged.
So something that worked perfectly a few weeks ago is now dead in the water because of an update on the IPads!!!!!!!! -
Open Firefox 4 in new window gives a Window frame and address bar does not refresh the current url
Using Firefox 4 in Windows 7
I have customised the position of tabs (Tabs on top) and which toolbar items I would like to see.
The first window I open of firefox 4 always has the configuration as I set it.
Whenever I open a new window of firefox either:
- Right-click a link to open in a new window
- Click a link anywhere (such as an email) to open a new window
- When a website opens a page in a new window
Bad Results:
- The new window does not have the configuration as set in the main window (Tabs on top)
- The new window has a windows type window frame around the firefox window (see two sets of window controls eg. "minimise", "restore" and "close")
- The open page does not show the url - navigating to a new page within this window will not update the url :: strangely enough clicking the url page icon will update the url as it should be
- Sometimes when restarting firefox, it will open the first main window with the remembered tabs and then open approx 8 or so blank new windows as described aboveThis issue can be caused by an extension that isn't working properly.
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
* https://support.mozilla.com/kb/Safe+Mode
* https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes -
storage-vdc(config-if)# show module
Mod Ports Module-Type Model Status
2 32 1/10 Gbps Ethernet Module N7K-F132XP-15 ok
sw1-gd78(config-if)# sh module
Mod Ports Module-Type Model Status
2 48 1/2/4/8 Gbps FC Module DS-X9248-96K9 ok
4 8 10 Gbps FCoE Module DS-X9708-K9 ok
7 0 Supervisor/Fabric-2a DS-X9530-SF2AK9 active *
8 0 Supervisor/Fabric-2a DS-X9530-SF2AK9 ha-standby
10 22 4x1GE IPS, 18x1/2/4Gbps FC Module DS-X9304-18K9 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
2 5.2(2) 1.1 20:41:00:0d:ec:fb:8a:00 to 20:70:00:0d:ec:fb:8a:00
4 5.2(2) 0.107 --
7 5.2(2) 1.8 --
8 5.2(2) 1.8 --
10 5.2(2) 1.3 22:41:00:0d:ec:fb:8a:00 to 22:52:00:0d:ec:fb:8a:00
sw1-gd78(config-if)# sh run int ethernet4/6
!Command: show running-config interface Ethernet4/6
!Time: Mon Feb 20 22:56:12 2012
version 5.2(2)
interface Ethernet4/6
no shutdown
sw1-gd78(config-if)# no shut
sw1-gd78(config-if)# speed 1000
ERROR: Ethernet4/6: Configuration does not match the port capability.
sw1-gd72# sh int ethernet4/6 capabilities
Ethernet4/6
Model: DS-X9708-K9
Type (SFP capable): 10Gbase-SR
Speed: 1000,10000
Duplex: full
Trunk encap. type: 802.1Q
Channel: yes
Broadcast suppression: percentage(0-100)
Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)
Rate mode: dedicated
QOS scheduling: rx-(2q4t),tx-(1p3q4t)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: yes
Link Debounce: yes
Link Debounce Time: yes
MDIX: no
Port Group Members: none
TDR capable: no
FabricPath capable: yes
Port mode: Switched
sw1-gd72# sh int ethernet4/6 transceiver details
Ethernet4/6
transceiver is present
type is 10Gbase-SR
name is CISCO-FINISAR
part number is FTLX8571D3BCL-CS
revision is C
serial number is FNS12090EMJ
nominal bitrate is 10300 MBit/sec
Link length supported for 50/125um OM2 fiber is 82 m
Link length supported for 50/125um OM3 fiber is 300 m
Link length supported for 62.5/125um fiber is 26 m
cisco id is --
cisco extended id number is 4
SFP Detail Diagnostics Information (internal calibration)
Alarms Warnings
High Low High Low
Temperature 36.21 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.29 V 3.63 V 2.97 V 3.46 V 3.13 V
Current 8.11 mA 11.80 mA 4.00 mA 10.80 mA 5.00 mA
Tx Power -2.65 dBm 1.49 dBm -11.30 dBm -1.50 dBm -7.30 dBm
Rx Power -2.21 dBm 1.99 dBm -13.97 dBm -1.00 dBm -9.91 dBm
Transmit Fault Count = 0
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warningAnkit,
You are trying to set speed 1000 on a 10g sfp.
type is 10Gbase-SR
You will need to insert a 1gig sfp and then you will be able to set the speed.
Also, I noticed that you posted first with interface 2/6 and the output you gave me was for 4/6. Are you sure you're in the right interface? -
When I connect my iPhone to my PC it is not recognised and iTunes does not open. When I connect my iPod to the same PC everything works perfectly. I conclude that the problem is not on the PC or with iTunes. Switching off and rebooting the iPhone and the PC does not fix the problem. Any suggestions??
Refer to this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538 -
My Mac Pro does not switch off.
It worked before Lion. Installed 10.7 and also upgraded to 10.7.1 but, on both cases, it does not switch-off. To be precise it "sometimes" switch-off but many times it does not. Let's say once on 15 times... With Leopard I nevere had this problem. (it persists also after a PRAM reset). I also run a second problem but only once and only upgrading to 10.7.1 (not to 10.7). It says that my RAM was on wrong position.. I had to remove and install the RAM again and it worked.
Any other case like this? (This append only on my MacPro - early 2009. On my MacBook and my MacBook Pro OSX Lion works fine).Is there a pattern to the chimes, or are they simply random, as if the Mac is repeatedly rebooting on its own?
Have you tried a "Safe Boot"? Press and hold a Shift key as you power up the Mac. Does it start then?
If it starts at all "Safe Boot" will take much longer than usual, that's normal. Shutting down will take longer also. Try it.
Maybe you are looking for
-
How to delete the orphaned Expected Rule Entries exist in the FIM portal
Hi, How to delete the orphaned Expected Rule Entries exist in the FIM portal. A large number of orphaned Expected Rule Entries exist in the FIM portal (originally 140000k+ objects, currently 75000+ objects). They consume the a lot of FIM database spa
-
Where to see the change phases in status.
Hi We are dealing with cases (SCASE) when the status changes (example, from warning to customer status =5 , to next warning ,status =10). In the 'history'(log)button one can read all about these, but at times I want to know ""when"" was the status ch
-
Concat Operation failing.[Error ORABPEL-10039]: invalid xpath expression
Hi , I am trying to concat two values which are as mentioned below concat(bpws:getVariableData('paramsVar','/ns7:parameters/ns7:item[ns7:name='ContractNumber']/ns7:value'),bpws:getVariableData('AccumilateEmail','/ns1:AccumilatePLAContracts/ns1:Accumi
-
I also tried downloading the ZXP file, but Extension Manager says "Failed to unpack the zxp file. Please make sure the extension is valid. the extension will not be installed." Any help is appreciated.
-
Hi, What are the things to be backed up while upgrading a version patch from 10.2.0.1.0 to 10.2.0.3.0 Please inform me... thanks Giri