Folder with an ! mark!

When i push a button on my ipod a folder just pops up with an exclamation mark . I plug it into my computer, and my computer will not even acknowledge that i plug it in! i do now know what to do!!! PLEASE HELP

additional info
Suggestions when you run into a problem of a Sad iPod icon or a folder icon with exclamation point with your iPod.
1. Try these five steps (known as the five Rs) will conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
2. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
Still can't see your iPod?
Several things could keep iPod from appearing in iTunes or in the Desktop/Finder when you connect it to your PC/Mac. The most likely causes are listed below in logical order. Check each one starting from the top of the list to see if that is what's keeping iPod from appearing.
3. Try to wait 30 minutes while iPod is charging.
4. Try another known-good FireWire or USB through Dock Connector cable.
5. Try another known-good FireWire or USB port on your computer .
6. Try to disconnect all devices from your computer's FireWire and USB ports.
7. Try to connect on a different computer i.e. a PC formatted iPod connect with a Mac computer or Mac formatted iPod with a Window base PC.
8. Try to do a Erase (Disk Utility) on a Mac computer or a reformat with a PC (Disk Management tool) but ensure you choose the right Drive (your iPod not your Hard Disk of your computer).
If one of the above step helps to get your iPod to be recognized with your computer, do a Restore.
But, if none of these steps address the issue, your iPod may need to be repaired. You can arrange for service at the iPod Service Website.
Post here again if you still cant solve the problem

Similar Messages

  • Hard drive crash? Folder with question mark

    Hi everyone! I had problems with my macbook pro (early 2013). Last week, it slowed down suddenly and the laptop heats up during sleep. Then the hard drive recently crashed, at least I thought it crashed after it showed the folder with question mark during startup and did not show my old hard disk drive. Now I bought a 1TB WD mainstream hard drive disk, unfortunately it does not detect it in the internet recovery (disk utility). Now my question is, Do I have to do something with the hard drive first for my laptop to detect it? Like formatting it? The box said that it is compatible with mac OSx Lion, but my internet recovery lets me install Mountain Lion only. Is that the problem? or is the problem internal like the cable that connects the hard drive to the logic board?

    That depends on the type of drive you have. If it is a standard external drive (in an enclosure) you can connect the drive with a USB cable.
    If it is a bare drive like this:
    You will have to put it an enclosure and get a usb cable. External drive enclosure are < $10. They come in two sizes, 2.5" and 3.5". Buy one that's correct for your drive. http://www.amazon.ca/MOGOI-Enclosure-External--Silver-Accessory/dp/B00HC107R6/re f=sr_1_5?ie=UTF8&qid=1404755872&sr=8-5&keywords=disk+enclosure

  • MacBook Pro flashes file folder with question mark and startup manager will not run

    My son's MacBook Pro won't boot (gets the flashing file folder with question mark).  When I try to open startup manager (holding "option" key during boot does not do it).  Other posts suggest inserting the install disk, but I am pretty sure that for Lion, there was no disk, it was just off the website through the App Store.  Any further suggestions?

    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • Not solved with Blinking Folder with Question Mark after Erasing Hard Drive

    Before asking, I found someone had asked exact the same question, but that was actually an unsolved thread.
    Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
    Level 1(0 points)sdc3gJul 5, 2013 6:24 PM Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
    Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings 
    in response to Niel
    Thanks for the reply, held command+R again and it is trying to pick up WiFi, but it's not picking up my network and won't accept the password even when I try to put it in manually. Any thoughts on that?
    Me too had tried the command+R and failed to manually connect to my network. Can anyone help?

    Well, it was solved. I shifted to other place and tried other WIFis. One of the WiFi had the 2002f problem and another was fine, so the reinstall worked smoothly eventually.
    On the apple support page it says that Supported network configurations and protocols includs both WPA/WPA2, not matter what they are, but it might not be true.

  • Imac froze and on re load folder with question mark appeared.  Now will not start up to home screen.

    The other night my Imac froze during updates.  I found it in the morning with the screen and mouse frozen and only the loading icon spinning.  I re stared the computer from the power button.
    Upon re loading the apple logo did not appear and was replaced by a folder with a question mark in the middle.  I looked this up online and found the best option was to use disk utility to check and repair the hard drive.  This showed an error with HFS.  Used disk utility to fix the hard drive so thast no error appear.  I re stared the computer but all it loaded was the folder with the question mark again, so I decided to erase the hard drive of any information (I back up quite regulary, but left it as last resort due to inconvenience), when installing again it seems to go so far before telling me it cannot install and I need to re start.  I have erased the dsk again and completed disk clean too before trying again and getting the same results.
    I am currenlty stuck at this point and need help, which would be appreciated.
    My Imac is an early 2008 Aluminimum model and installtion disk is 10.3

    The folder with ? mark mean one of 2 things.
    1) The OS is so corrupted that the hardware can't find it as a valid way to boot the system.
    2) Your hard drive has failed.
    You can try booting from the Recovery HD partition, Commadn + r keys at startup if you are running Lion Mt Lion or Mavericks.
    Or boot the system from the original System reinstall DVD that came with your Mac or an upgrade OS X install DVd you may have purchased.
    With either use Disk Utility to see if the hard drive is seen and if it can be erased or repartitioned and then restore from a Time Macine baclup or reinstall OS X.

  • Switched on my imac 24inch intel based and all I get on screen is a folder with question mark flashing,I had backup on external hard drive but when I try to reinstall it can not find my mac hard drive

    Hi when I started my intel based imac this morning all I am getting is a folder with question mark in the middle flashing,I have external hard drive with backup,but when run disc utilities it does not show my mac hard drive.hope someone can help.(it's running mountain lion, well it was)

    Try starting up your Mac while holding down the Option key. That should prompt the Startup Manager window where you can select the startup disk then click Restart.
    The question mark folder indicates your Mac cannot find a system folder to boot from.
    A flashing question mark appears when you start your Mac

  • Folder with question mark keeps coming back

    Hello there , i have a problem with my mac pro.
    The problem is that every time i start up the mac it can't find my startup disk and then gives me the Folder with ? mark in it.
    Some times just do a start up for the second time helps but most of the time i will have to hold the alt button pressed, and then some times i get to choose my start up disk from there but most of the time it then starts up from my boot disk.
    When it has started up and i then go to the pref's , select my boot disk and lock the prefs so basicly it would not be able to chance that disk without my password, i find the next time i start it up, with all the same problems, the lock is also no more activated in my prefs.
    I tried several things already, resseting power management, pram , Applejack, combo update 10.5.5, repare permissions ...., until now nothing helped solve the problem.
    My Mac Pro 8 core, was just back from the dealer to get a new raid card battery and it worked fine for a while.
    The startup disk is disk 1 in JBOD on the raid card by the way.
    I feel that this problem started occuring after the 10.5.5 and java updates
    but since those 3 things came very close together i'm not 100% sure.
    I hope someone here can help me out with finding a fix for this problem because i have run out of ideas and i wanna avoid a reinstall of my system .
    Thank you for your help ,Data from the Netherlands.

    I tried several things already, resseting power management, pram , Applejack, combo update 10.5.5, repare permissions ...., until now nothing helped solve the problem.
    I am not ready to say Applejack is as safe as it use to be.
    I can say that making a backup with SuperDuper is essential; as is having OS X "EMergency" boot partition or drive (FW, someone said that used 8 or 16GB SDHC memory card).
    And use Disk Warrior along with Apple First Aid to repair your drives.
    Anytime you zap pram or SMC you have to reset the startup disk, and it sounds like your disk or NVRAM is a problem.
    Personally, I like a single fast dedicated boot drive; or, a stripped RAID (and instead of mirror better off keeping a good backup image cloned).
    So clone your system only to another drive with SuperDuper.
    Repair your boot drive with Disk Utility and Disk Warrior (or TechTool Deluxe/Pro).
    If you think 10.5.5 may have caused it, roll back to 10.5.4, that is what backups and making a clone of your boot drive are good for. And always make a backup before you even begin to upgrade the system.

  • I powered up my macbook and there is a file folder with question mark on the screen flashing.  What does that mean?

    Powered up Mac book and screen showing file folder with question mark flashing? 

    A flashing question mark appears when you start your Mac
    Hope that solves your issue.

  • Folder with Question Mark on Start-up/ DOS-like screen with errors now...

    Left my Mac Pro running last night, woke up to it being frozen (looked like it was
    in hibernation mode and wouldn't wake up).
    Forced a shut down from button on tower - on start-up, went gray screen
    with blinking folder with question mark.
    Inserted install disc 1 and held down 'C' - Went to choose your lang menu,
    I picked English, went to choose start-up disc. Options were the install
    disc and a network drive with a question mark. I picked drive with
    question mark.
    Computer looked like it was trying to restart, apple with loading circle
    spinning, and then blinked to a black screen that looked like DOS that was
    blinking error messages (one message was "diskOs2 undefined Oxe0030005")
    Any suggestions?
    Mac Pro   Mac OS X (10.4.9)  

    Was there a storm or outage that could have brought it down? for now it sounds like a kernel panic screen is what you are seeing. If you don't have a UPS, I wouldn't be w/o. Never know when one of those high winds will knock out power.
    You could try to do an SMC Reset and see.
    I assume you usually sleep the system and it doen't have trouble with wake from sleep, and you haven't altered the system (new hardware etc) in any way that would change that.

  • Folder with Question Mark, to Apple Icon, to Kernel Screen at Startup.

    At startup Folder with Question Mark, Followed all steps to resolve it to no avail, I try to re-install Snow Leopard and Apple Icon with Grey screen appears, then Kernel screen.
    I cannot get past the Kernel screen.  No options to click anything, like system preferences or anything. I have a Macbook, with Snow Leopard.  Any help would be much appreciated.
    I tried Pram Reset and everything.

    Hey, thanks for the quick reply Mende.
    I tried that, it goes to the apple icon, however after about 10 seconds of the apple it goes straight to the Kernel screen.  It doesn't give me the options of opening anything. Infact it doesn't even have a mouse curser.
    If I hold "option" it gives me the option of choosing only the "Leopard DVD" but that's it and then it goes to the Kernel Screen
    Again, thanks for the taking the time to help me out.

  • Folder with question mark + wont boot from disk

    Hi
    I am trying to reinstall a powermac g5 from the disk, using a old hard drive that works.. (formatted in NTFS) (hoping that when selected to boot from disk, mac will then erase and reformat it)this image is presented when i hold down the option key and the disk ejects this other image is presented when i hold down C (folder with question mark blinking) and the disk ejects... also presented if i boot normally.... Could some help be offered please??????
    Powermac G5
    Thank you in advance

    Yes, you must Format it HFS+ first...
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    How to format your disks...
    http://www.kenstone.net/fcp_homepage/partitioning_tiger.html
    (To Install OSX on an IntelMac the Drive it needs the GUID Partitioning scheme mentioned at the bottom.)
    Thanks to Pondini, Formatting,  Partitioning, Verifying,  and  Repairing  Disks...
    http://web.me.com/pondini/AppleTips/DU.html

  • Folder with question mark keeps showing on boot screen

    folder with question mark keeps showing on boot screen

    Click here and follow the instructions. If the computer was running Mac OS X 10.6.8 or earlier and you reach the third set of steps, insert a Mac OS X install disk.
    (120871)

  • Folder with Question Mark on Boot

    I can't get my mac to boot. Instead I get the gray screen and a folder with question mark icon. I'm guessing the HD is dead? Any chance for recovery? If not how much does a new one cost? The one year warranty just expired!
    Please help!
    Thanks,
    Brian

    So, what is it? The thing froze today and wont reboot - just a gray screen with NOTHING. Then after about 10 min. the flashing question mark folder appears.
    So, I popped in the install DVD that came with the computer, get the little gray Apple logo and it boots from the DVD.
    Launch Disc Utility. The HD appears on the left. Click on it - all of the "Verify" and "Repair" buttons remain grayed out. So what the hxll do I do?
    I cant boot into single-user mode or any other mode for that matter.
    This is a Macbook pro, dual-core Intel, less than a year old.

  • Folder with question mark and smiling mac face at start up

    After I was importing some video today, shut down G5 and on start up I get the folder with question mark and smiling mac face.
    Any help?
    Power Mac G5   Mac OS X (10.4.8)  

    Boot from a drive with Disk Warrior 4, or your emergency boot drive (FW or alternate) or if you lack that, use single user mode to run fsck command. The last option would be your Tiger DVD but that may be 10.4.3 or earlier and not your best.
    I say that because it seems like it was more than just needing to reset the startup disk preference and may have a corrupt directory. It shutdown smoothly and fully?
    At the least, using the OPTION key and SHIFT key for Safe Boot. My recollection of trying to do both is that it won't. You can do one or the other, but not both. So running FSCK is just insurance to repair the directory.

  • Flashing folder with question mark at Startup

    Here is what I know so far.
    - The computer was powered off by pushing the power button without shutting down.
    - The computer was then restarted and it was coming into the white screen with the Apple logo in the middle, but i noticed that it was skewed slightly (like someone took a 4:3 ratio screen and stretched it to a 16:9) and then it would show a circle slash icon and then the flashing folder with a question mark on it.
    - It would not come up in single user mode (Command + S) and it said that there was an error loading kernel 'mach_kernel'
    - It would not come up in safe mode (Shift)(The flashing folder came up again)
    - I reset the PRAM (Command + Option + p + r) and it seemed to fix the problem with the stretched screen but did not help the boot situation (still got flashing folder)
    - I did the start up where you can select the hard drive to boot with, it owed the HD and i selected it, but then i got the flashing folder with question mark.
    - It would not come up in Verbose Mode (Command V) Error loading Kernel again.
    - I bought a FireWire cable and hooked it to another MacBook Pro, and booted the faulty Mac into Target Disk Mode, the FireWire logo came up on the screen and bounced around like all forums said that it would, but the drive would not show up on my host. I checked the System Profiler on the host and it did acknowledge the Target Disk Mode was there, but the drive of the target would not show up on the host. I restarted the host, nothing. I checked all of the connections, nothing. I replugged all of the connections, nothing. I even reversed the FireWire cable, nothing.
    - I have DiskWarrior 4 if i can get the drive to show up in TDM, but nothing so far.
    Does anyone have any suggestions?

    Thanks for your help guys. I managed to get the computer started by holding down C at the Start Up with the Install Disc 1 in the computer. The disc was really kindof unnecessary, as the newest version of Mac OS X (10.4.10) became available via the hard drive.
    I then found out that the battery was not installed, so I reset the management system by removing the A/C power, the battery and pushing the power button for 5 seconds, and then reconnecting everything. It did not help, the battery is bad i guess, so I am going to call AppleCare and get a new battery.
    Thanks for your help.

  • My computer has a blinking folder with question mark on it at start... What is going on?

    My computer has a blinking folder with question mark on it at start... What is going on?

    The hatter wrote:
    also that the default is no longer set  asin when someone had windows as default and removed it w/o changing Startup Disk panel.
    Oh yes, I forgot that people still do that

Maybe you are looking for

  • Word Mole for Mac

    Anyone know how I can download Word Mole for my Mac?

  • Lost disk space after each reinstall.

    I've had to reinstall leopard on my macbook three times in the last week for different reasons. After each reinstall(erase and install) it appeared that I lost a little more GB to the HDD. I have a 250GB HDD, and I know it actualls reads as 232.87, b

  • Oracle10g - Startup hang - Parameter: local_listener

    Hello guys, i have got an error which i don't understand. I deleted an old entry from tnsnames.ora and forgot to delete the local_listener entry in the spfile/pfile. I read the following document: http://www.valentia-gmbh.de/twiki/pub/Viki/FehlerOra1

  • Can I call a VB object in a stored procedure?

    I need a PL/SQL stored procedure to call a Visual Basic object. Can it do that? If so, how? Someone mentioned using a cartridge, but I can't find information that supports that. Thanks for any help! Tami

  • Air 1.5 update breaks Air apps for Linux

    The beta version of Air worked fine, but after updating to Air 1.5, apps will no longer run or install. The installer says the air files are damaged. I've tried uninstalling everything & reinstalling. I don't suppose the beta version is still availab