For all iPad owners with video freezing concerns- read this first!

First of all, take a deep breath, acknowledge that it is not your fault, and there is nothing you can do with the software to fix it. It is a hardware problem, most likely video chip related, that is ONLY solved with replacement. I have had several discussions with senior tech support who won't say exactly what the cause is, but admit that there is nothing a user can do to fix the problem other than replacement. Which they will happily provide. This is where it gets tricky.
If you are like me, you can't live a day without your iPad, even though you also have a smart phone, a net book and a laptop....if I can admit it, so can you. So if your local store has a brown box replacement for your model, go in and get it replaced, and you are done. Most of the time, this will fix the issue because they test these ones first. If you are like me and your store does not have a replacement for your wifi only model, then you have to either drop yours off and wait for a replacement to be shipped in 4-5 business days, or purchase apple care where they will hot swap a new iPad with you with overnight to your doorstep. This is the way to go and here is why: you can't be without your iPad and you won't be. AppleCare is $100 that is fully refundable at a pro rated time period. So you have it for 1 week and then cancel it. Cost of use? Should be about $2. And the experience is seamless. This is just my opinion, but it worked for me!

taffytafftaf,
Agreed; The problem might very well be a hardware one. After all, these symptoms are very weird. It's undoubtedly a great phone. The main reason I bought it was to have the first decent looking WCDMA phone out there (that works in Europe) and I still quite like it.
To tell you the truth though, I was going to replace it with a 8GB N91, until I tried one yesterday. It's way too bulky, actually the dimensions seem weird - nothing like my old 8850. The HDD explains everything, but I really don't need another DAP or a pocket drive, so it won't quite do.
I'll take your advice and take the 6630 to my nearest NSC. Hopefully they'll be able to revive it. If not, I'll replace it with something very small.
"Good luck"
Thanks, I'll need it!
mbamg,
I think it's a case of "what goes around, comes around". You've obviously taken good care of your phone, whereas I haven't. I definitely should've taken it to a NSC to be updated. These problems, as mentioned above, might also have something to do with the hardware, as the phone has taken some unintended abuse during the years. We'll just have to wait and see.
The original RS-MMC card was in the phone when it was updated. After that the phone claimed it was faulty. Other cards don't seem to work either. Unfortunately formatting them didn't help.
I still partially blame the NSU, since these problems didn't surface until the software was supposedly "successfully updated". My 6630 is a bad combo of possibly damaged hardware and new firmware.
Thanks once again for your input guys, I really appreciate it!
Current communication arsenal:
HTC P3600 / Nokia 6630 / Globalstar GSP-1700

Similar Messages

  • Lockups, crashes, video freezes, BSOD, Read This!

    ...or other mysterious ailments.
    Before you tweak anything, go here and determine your power consumption (recommended power.) Remember to add a bit if you overclock and/or run onboard graphics, and/or USB mouse/keyboard. Don't forget your sound card (if any), hard drives, CD/DVD drives, system fans, and something other than stock cooling. If you can't find your device, then find the specs and plug in something close. Also, if you OC, list your processor as the one that runs your OC speed (e..g a 2500 clocked to a 3000). Also, don't forget it's better to be a little over than a litle under.
    http://www.jscustompcs.com/power_supply/
    After determining your power consumption, look at the real specs of your supply (available from the label, manual, and/or manufacturer's website) and NOT total Rated Watts. Use the peak max wattage of the +3.3V, +5V, and +12V rails together.
    If your total combined configurations come close (say within 10%), meet, or exceed the three rails spec, consider getting a new power supply before you troubleshoot any further.
    E.g., if you run an Antec Soultion Series SL400 supply, then, according to specs, your max current draw on the combined +3.3V, +5V, and +12V rails is 380W, not 400W. If your recommended power supply figure (from the above link) is, say 360W to 375W then you might want to think about getting a bigger power supply. If your recommended power supply is 380W or more, get a new supply, no question.
    This is not a panacea (cure-all), but a very good place to start.

    Hi,
    I had the same problem and downgraded to the lower version. now the video works without any problem, but there seems to be another problem. when I want to eject the ipod from itunes, I get a message, that the iPod cannot be ejected because data on the iPod is currently used by an external program...
    any idea...?
      Windows XP  
    UPDATE: AFTER RESTARTING THE PC IT WORKED WITHOUT PROBLEMS!

  • If you are JUST now signing up with your new iPhone Read this First!!

    If you have not begun the activation process - Stop Read - and then Proceed.
    Sign up for a new number when you activate!!!!
    DON"T MOVE YOUR NUMBER OVER
    If you are with AT&T - add an additional line
    If you are with another carrier - Get a new number.
    You can bring your old number over to the iPhone at a later date. The back log for activation is on bring in old numbers over - Not for new numbers.
    So, if you want to wait in vain and ***** and moan and suffer like the rest of us - Say you want to bring your number over.
    If you want to start playing with the coolest phone ever: Get a new Number, then deal with having your old number moved once the insane sign up frenzy dies down a bit in a few days.
    I'm sure this activation problem will go away, once the frenzy is over.
    My two bits.
    enjoy your phone!
    iMac 20" Intel core 2 Duo   Mac OS X (10.4.9)   2GB RAM Installed

    If you have not begun the activation process - Stop
    Read - and then Proceed.
    Sign up for a new number when you activate!!!!
    DON"T MOVE YOUR NUMBER OVER
    If you are with AT&T - add an additional line
    If you are with another carrier - Get a new number.
    You can bring your old number over to the iPhone at a
    later date. The back log for activation is on bring
    in old numbers over - Not for new numbers.
    So, if you want to wait in vain and ***** and moan
    and suffer like the rest of us - Say you want to
    bring your number over.
    If you want to start playing with the coolest phone
    ever: Get a new Number, then deal with having your
    old number moved once the insane sign up frenzy dies
    down a bit in a few days.
    I'm sure this activation problem will go away, once
    the frenzy is over.
    My two bits.
    enjoy your phone!
    iMac
    20" Intel core 2 Duo   Mac OS X (10.4.9)  
    2GB RAM Installed
    Activation, selecting to move my existing AT&T number, worked fine. The whole process took barely 5 minutes to complete all within ITunes.

  • I am a new iPad owner with Mac OS 10.4.11. Currently I have iTunes 9.2.1. What do I need to do to be able to sync my iPod settings in iTunes to my iPad? The  newest version of iTunes says I can't install since it requires 10.5 or later.

    I am a new iPad owner with Mac OS 10.4.11 on my desktop. Currently I have iTunes 9.2.1. What do I need to do to be able to sync my iPod settings in iTunes to my new iPad? The  newest version of iTunes says I can't install it since it requires 10.5 or later.

    Mac OS X 10.5 Leopard installation system requirements
    http://support.apple.com/kb/TA24950
    Leopard is no longer available at the Apple Store but may be available by calling Apple Phone Sales @ 1-800-MY-APPLE (1-800-692-7753).
    If you can't obtain a retail install DVD from Apple, look on eBay or Google the installer part numbers to possibly find at an on-line store. Here's what to look for:
    MB427Z/A  Leopard 10.5.1 install DVD
    MB576Z/A  Leopard 10.5.4 install DVD
    MB021Z/A  Leopard 10.5.6 install DVD (single user)
    MB022Z/A  Leopard 10.5.6 install DVD (5-user family pack)
    Installing Mac OS X 10.5 Leopard
    http://support.apple.com/kb/HT1544
    Mac OS X 10.5 Leopard Installation and Setup Guide
    http://manuals.info.apple.com/en/leopard_install-setup.pdf
    After you install the base 10.5, download & install the 10.5.8 combo update at http://support.apple.com/downloads/Mac_OS_X_10_5_8_Combo_Update
     Cheers, Tom

  • Hey, I have an unopened iPad mini that I won at work and I'm wondering if there's an upgrade option where I can exchange this for an iPad mini with retina display? Thanks

    Hey, I have an unopened iPad mini that I won at work and I'm wondering if there's an upgrade option where I can exchange this for an iPad mini with retina display? Thanks

    Take it to an Apple store and ask. All they can do is say no. They may ask for a purchase receipt to make sure it's not stolen.
     Cheers, Tom

  • When I add a https link to quicklinks, when I click on it, the (:) after https does not go to the address bar and thus the link is not connected. This is happening for all quicklink bookmarks with https:

    Question
    When I add a https link to quicklinks, when I click on it, the (:) after https does not go to the address bar and thus the link is not connected. This is happening for all quicklink bookmarks with https: Is there a solution?

    Try some basic troubleshooting.
    '''Try Firefox Safe Mode''' to see if the problem goes away. [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] is a troubleshooting mode that turns off some settings, disables most add-ons (extensions and themes).
    If Firefox is open, you can restart in Firefox Safe Mode from the Help menu:
    *In Firefox 29.0 and above, click the menu button [[Image:New Fx Menu]], click Help [[Image:Help-29]] and select ''Restart with Add-ons Disabled''.
    *In previous Firefox versions, click on the Firefox button at the top left of the Firefox window and click on ''Help'' (or click on ''Help'' in the Menu bar, if you don't have a Firefox button) then click on ''Restart with Add-ons Disabled''.
    If Firefox is not running, you can start Firefox in Safe Mode as follows:
    * On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
    * On Mac: Hold the '''option''' key while starting Firefox.
    * On Linux: Quit Firefox, go to your Terminal and run ''firefox -safe-mode'' <br>(you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
    When the Firefox Safe Mode window appears, select "Start in Safe Mode".<br>
    [[Image:Safe Mode Fx 15 - Win]]
    '''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
    ''To exit Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
    When you figure out what's causing your issues, please let us know. It might help others with the same problem.

  • In Apple Configurator, can I set up different sets of iPads with different apps loaded? Or will all iPads synced with Configurator be required to have the same build?

    In Apple Configurator, can I set up different sets of iPads with different apps loaded? Or will all iPads synced with Configurator be required to have the same build?

    Hi jshira86,
    You can definitely have different sets of iPads with different apps loaded. When you "supervise" your iPads, you will see that on the left side of the Configurator window there is a "+" sign in the lower left corner. Click it to create a new device group. With this new device group you can choose what apps and configuration profiles you want to install on that group of iPads. Create as many groups as you want to customize the apps and profiles you want on them.
    Hope this answers your question!
    ~Joe

  • FOR ALL ENTRIES IN with two tables

    Hi Guy's,
    I have two int. tables, gt_likp, gt_lips.
    I need to use "FOR ALL ENTRIES IN" with this two tables.
      SELECT matnr
             vkorg
             vtweg
             ypcogsl
        FROM mvke
        INTO TABLE gt_mvke
    <b>    "FOR ALL ENTRIES IN gt_likp gt_lips"</b>
        WHERE matnr = gwa_liefpos_tab-matnr
        AND vkorg = gt_likp-vkorg
        AND vtweg = gt_lips-vtweg.
    How to do this?
    Please Help.
    Thanks in Advance.

    Hi,
    Fill gt_likp-vkorg values in a range(r_vkorg). Use gt_lips in FOR ALL ENTRIES.
    Basically you can use only 1 internal table with FOR ALL ENTRIES statement.
    SELECT matnr
    vkorg
    vtweg
    ypcogsl
    FROM mvke
    INTO TABLE gt_mvke
    FOR ALL ENTRIES IN gt_lips
    WHERE matnr = gwa_liefpos_tab-matnr
    AND       vkorg in r_vkorg
    AND       vtweg = gt_lips-vtweg.
    - SRao

  • TS3274 its almost 10 months,i purchased ipad2 32 3g wifi.itinially i got problem with applications shut off frequently now since last 4 months my ipad starts with a message (connect iTunes)like first time start and going to restore mode and it occurs freq

    its almost 10 months,i purchased ipad2 32 3G wifi.itinially i got problem with applications and safari shut off frequently now since last 4 months my ipad starts with a message (connect iTunes)like first time start and going to restore mode and it occurs frequently.plz advise.

    If you have followed the standard Apple troubleshooting processes (see user guide )
    probably a trip to the local Apple Store Genius bar is called for before warranty runs out
    Assuming the iPad has been released in your Country if not you may have to take it to a
    neighbouring Country where it is available
    This page will tell you ,via the drop down menu Countries that can support iPad
    http://support.apple.com/kb/index?page=servicefaq&geo=United_Kingdom&product=ipa d

  • I pay for upgrading ifindyou and it doesn't work!!!! it clearly says that it tracks only your mobile in the lite version, after you ask the upgrade for all the mobile... can we call this a fraud????

    i pay for upgrading ifindyou and it doesn't work!!!! it clearly says that it tracks only your mobile in the lite version, after you ask the upgrade for all the mobile... can we call this a fraud????

    Hi,
    "A day after the name change became official my built in skydrive app stopped working"
    Did you point that SkyDrive changed to OneDrive?
    Did you move your OneDrive to another location or change its name?
    Please login OneDrive with web-based to check if you could access it successfully.
    Please refer to the following article to try the troubleshooter and check the service status:
    SkyDrive: FAQ
    http://windows.microsoft.com/en-in/windows-8/skydrive-app-faq
    Karen Hu
    TechNet Community Support

  • HT4589 When using compressor voice is not sync with video. What causes this and how to fix it, please?

    When using compressor voice is not sync with video. What causes this and how to fix it, please?

    Although you say you have let the battery drain, was it for long enough? Since nothing else that you've tried so far has worked, I suggest that you leave the iPod unplugged for at least four days, preferably a week. That way, if something is stopping the iPod from turning the screen on, then whatever it is will drain the battrey. However, since the screen isn't on, that may take longer than if the screen was on.
    Then, after that time, plug the iPod into a power source and leave it alone for at least thirty minutes. Only after thirty minutes will it show any signs of life, but you should leave it until it is fully charged before trying to use it.
    If you get to this stage, the fact that the battery has drained will cause the iPod to reset when it springs back to life.
    Let us know how you get on.

  • T500 Driver crash problem, for all upgrading owners

    To all the T500 Owners who have upgraded to windows 7. There is one major problem hindering a lot of t500 owners. Someone mentioned earlier in this thread to download the catalyst 9.9 drivers from ATI.  Everything else has worked great and all the drives have automatically been updated smoothly.
    They install properly but after a restart this is what happens as mentioned by another user
    "Hi I have a big problem with my lenovo T500. I installed Windows 7 RC x64 to my lenovo T500 (2082-53G) and when I install the ATI catalyst beta driver v9.9 from ATI's homepage, my computer freezes at startup (some activity on HD but I can't move my mouse and many processes faile to start at boot). I'm not the only one facing this problem: Lenovo T500 Thinkpad - WDM Radeon 3650 Driver Update Causes Screen to Freeze"
    I have the exact same problem.... have formatted twice already, gone into safe mode, theres no getting around this problem.
    Any help? I have the 32 bit version of windows 7 enterprise 90 day trial.
    I know we might not be able to swtich the graphic cards, but at the very least we should be able to pick one in bios and  be forced to use that.  At this point its not even allowing me to install the discrete driver.

    Hi SuperWoofer,
    Thanks for your sharing. You're very helpful indeed! =)
    Regards,
    Cleo
    Message Edited by Cleo_Lenovo on 06-12-2009 11:43 AM
    WW Social Media
    T61, T410, x240, Z500, Flex 14
    Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    Follow @LenovoForums on Twitter!
    How to send a private message? --> Check out this article.
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Drop down menu for all ipad and samsung tablets and desktop

    Does anyone know any drop down menu that works in all ipad and other mobile devices (like samsung tab 2) and desktop and how to use it in Oracle APEX? I played with the "pull down menu" in theme 24 - to replace page tabs - and it didn't work very well with sublists. Since the "hover" event didn't work in mobile devices, it already navigated to the target before the sublists showed.
    Thanks.

    I am still new in this area but this is what I would suggest:
    Depending on with Apex Version you are working with - and as I understand, a lot gets far easier with 4.2, when it comes to development for mobile devices - I would work with jQuery Mobile.
    A very nice introduction (at least for me) was this youtube Video with Peter Raganitsch.
    JQuery Mobile gives you the tools to create a very nice touch-friendly popup list.

  • Droid X2 Owners with Freezes/lockups READ THIS!! and VZ/MOTO employees!!!

    I am COMPLETLEY convienced the Freeze/lockup has something to do with the SD card or SD card slot. i retored my phone to 100% stock yesterday, NO bloatware removed etc...ran so nice all day, this morning i decided to put the SD card that came with it back in the phone, formatted it, and BOOM within 15 min, SCreen lock up
    MOTO and VZ, you need to look into this. i think that is the issue on the freezes. im going to maybe call and see if i can get a replacement....
    **also has happend with a seperate 32 Gig SD card*** SD card slots bad???

    Interesting.....if you are running GB, then that's probably your problem. I have had an original DX since Nov 2010 and up until August when they released GB, I had absolutely no problems with the phone. Once GB got installed to the DX, the SD card started having serious issues. The card the phone came with just up and completely corrupted right after GB got installed on the phone, and then the replacement card that I was forced to go buy (VZW refused to replace it but that's an entirely different story) has had problems 3 seperate times since I installed it into the phone since the end of August....seems like every 3-4 weeks the SD card suddenly has file system errors and I cannot read anything on it (computer won't even recognize it), so I end up losing pictures, ringtones and other things to the point that I have regularly back everything up to my computer just to make sure I can keep these pictures and ringtones.  They're not all that important pictures, but still....if I was able to go 9 months on Froyo with NO problems with the SD card (or phone for that matter), then how come 2 months since VZW pushed the GB update to the phones are there regular occurences......something is fishy in Denmark with all these sudden problems
    I would hope that VZW and Moto would realize the problems increased ten-fold since GB was pushed and actively attempt to fix them once and for all, but I truly believe they view it as the phone being EOL (no NEW phones are sold anymore) that the issues are no longer of a big concern to them. Seems like the only answer is that as we are able to do so, just upgrade to a different phone. I know for a fact that I will NEVER get another Motorola phone.....the DX is a great phone, but Moto, and to an extent VZW, have truly caused the phone to go down the proverbial toilet, which is a shame

  • IPod (with video) freezes Windows XP - POSSIBLE SOLUTION

    Hi everyone,
    I bought a 5g 30gig iPod with video a few days ago, and immediately ran into the "iPod freezes Windows when connected via USB 2.0" problem. I read through every possible post on this website, on iLounge, on Microsoft's forums, etc. There seems to be quite a substantial number of people running into this problem, because I've been seeing posts about this all over the place.
    My specific problem was that whenever I plugged in my iPod, the iPod would display "do not disconnect" and iTunes would begin to recognize it - sometimes it would reach the point where it would begin to update - and then the computer would completely freeze. The iPod would "disconnect" and be completely usable, but the computer would not respond to anything what-so-ever. I had to perform a hard restart to get the computer usable again. No error messages, no "ctrl-alt-del" saves, nothing. It would also lock in the same exact way if I just plugged the iPod in without starting iTunes (iTunes wouldn't automatically start, computer would just lock up after a few moments).
    Anyway, my problem was solved through a procedure I saw in a post somewhere (I'm pretty sure it was on these forums, actually). Basically, it seems as though there is some sort of conflict between iTunes, Quicktime, and Symantec's anti-virus.
    The process is pretty simple - completely turn off whatever version of Symantec you're using (Norton AntiVirus, Firewall, whatever... I'm running Symantec Corporate AntiVirus 10). Then, uninstall Quicktime and iTunes (it might not be absolutely necessary to completely uninstall iTunes - I uninstalled Quicktime and then "repaired" the iTunes installation).
    This seemed to resolve the situation entirely - I've updated my iPod three times now, and charged it, with no problems. Hopefully this continue to work... !
    Incidentally, I think it's disgusting that this seems to be such a prevalent problem, yet Apple so far refuses to acknowlege its existence, much less provide a solution. As a long-time Windows/Microsoft user (notice I didn't say 'fan'), I expected much more from Apple.
    Anyway, good luck!
    - Damion
    IBM Thinkpad x30   Windows XP Pro   Pentium IIIm 1.3ghz, 768mb RAM

    Hi!
    I have the same problem, though using iPod Touch.
    My PC crashes just after charging sound on th iPod sounds.
    I can be loggen on or not.
    I have tried the 5R's two times
    I have removed SP3, didn't help.
    I have updated to iTunes 8.0.1: Didn't help.
    But I have an portable PC (job PC) where it is working fine, both PC's using XP Pro, english version.
    So, just now, I am very dissapointed bu the Apple products (and it took me 20 years of Software Engineering before i bought something from Apple ..... )
    So the stress test will be: Will Apple do anything with this ?

Maybe you are looking for

  • Materials do not have a Target cost collector value/credit for the Final pr

    Hi, while running the sap report kkbc_pko, the materials do not have a target cost collector value . please guide me how to add the value to the material cost collector regards yogesh

  • Partition of HDD

    Hi everyone, I just bought a HP Pavilion slimline 400-235d desktop PC with 1TB HDD How do i partition the 1TB HDD into D, E and F drives without formatting the entire HDD? Any free and reliable software to do it? Thanks and regards, Steven

  • Updating Folio

    Hey everyone, as I read before, I´m not the only person with a serious update-problem. Does anyone know, how to solve this? I am working on a folio including many single articles. Now I made some changes at article No8 (nothing serious, just a font s

  • Dynamic class calling

    Hi All, I want to know the same class name which I am executing in the constructor of the class. Is there any system variable which stores this information. Like for example sy-repid for reports. Then after getting the calss name in string  how I am

  • Whats most common naming convention for MP3s (what does iTunes store use?)

    Trying to organise all my tags and music. I am using iTunes and some other tag (tag%rename) WMP etc, as some seem to not show all the tgs of other programs) However what is the generalised, most common naming convention for MP3 files? ie. track no, A