For new PCsuite

Hello,
I suggest for the new pcsuite, apart from supporting vista, the "hability" of storing all contact details. Now, if you have in your agenda a contact with 4 or 5 telephones, pcsuite stores only the two it wants.
Best regards

nHi,
Before doing any resets on your phone, kindly try this first
Do have backup of your phone data & PC registries then Uninstall Nokia PC Suite, Nokia Connectivity cable driver, PC Connectivity solution, Nokia flashing cable driver(if any on your PC), Run PC Suite cleaner. Install latest Nokia PC Suite from europe.nokia.com/pcsuite, reboot your pc. Once pc started, connect your phone with USB in different ports of your PC and check
Please do remember your default codes for resetting... If its failed for more than 3 attempts, you have to visit Nokia Care centre..... SO be carefull
Hi some reset codes
*#7780# "soft reset" :sets factory defaults WITHOUT erasing your data.
Use this code if you REALLY must
*#7370# "hard reset" : sets factory defaults AND deletes your data!

Similar Messages

Mail constantly checks for new mail; downloads same emails repeatedly HELP!

For the last three days (since 19th), Mail has been downloading the same emails over and over again. I first noticed a problem when about 20 spam emails that usually route to my Junk folder appeared in my Inbox. I thought I had just moved it incorrectly and deleted them, then they appeared again later.
The mail jogger cycle (next to Inbox) keeps turning and turning like it can't stop checking for new mail. How do I get it to stop?? The emails are multiplying like gremlins in my Inbox and driving me nuts!
Also, it only downloads new emails when I first open the app. I have to force-quit out of Mail, then reopen, and I will get a couple of new emails, and then ALL THE EMAILS FOR THE LAST THREE DAYS AGAIN.
Mail was working fine for me until three days ago. The only thing I've changed recently is a Software Update on the 15th for QuickTime and iTunes.
Please help! I tried to Repair Permissions and it didn't do anything. I also tried removing all messages from the server and that did nothing either.
Mail Version 2.1
THANK YOU ANYONE WHO CAN HELP ME!!
iMac G5 Mac OS X (10.4.7) 2.1 GHz, 512 MB Memory

UPDATE: I think I got it to stop checking mail. I have Yahoo mail and I checked my email through online Yahoo. I was able to delete a bunch of emails and it suddenly stopped checking for email in the Mail app.
HOWEVER, it will NOT remove some of my junk emails. I was able to delete over 100+ of them. But one specific message (which I now have 8 copies of) will not go away. It is one of those 'Delivery Status Notification' emails. Is this a virus??
I've tried Erasing Deleted Messages and Erasing Junk Mail. Neither helps. These emails won't go away.
Help please! I would be very grateful.

Data not loading for new Fields InfoObjects from DSO to InfoCube

Hi Gurus -
               I have a DataSource that is providing data to existing DSO then to Infocube. My client asked me to added couple fields to DataSource and get the data to DSO and then DSO to InfoCube.
Here is the Old scenarion:   DataSource -> DSO -> InfoCube.
Here is the New Scenation:
     DataSource ( Added new fields) -> DSO (added new InfoObjects for Corresponding DataSource FIelds) -> InfoCube( Added new InfoObjects to mapped from DSO)
I added the new fields to DataSource, added the corresponding InfoObjects to DSO and InfoCube.
I successfully loaded data from DataSource to DSO. Data is populating for the new Fields/InfoObjects in DSO.
But when I load data from DSO to InfoCube, I don't see any data for New Fields InfoObjects in the InfoCube.
Data from DSO to InfoCube is loading fine for the Old InfoObjects Fields but not for the New InfoObjects I added in InfoCube.
-Sonali

Hi,
Why dont u debug the load through DTP debugging and check what happens to the source field and target field once it passes through the transformation. You can easily trace back where the fields are becoming blank.
The loads which you have mentioned earlier did it have values in Added Records/Transferred Records column for the cube.
Regards,
Mani

Software Update Server - Deleting old updates to make space for new ones

On Page 77 of the SystemImage_and_SW_Updatev10.4.pdf Apple recommends "deleting old updates to make space for new ones". I've looked and searched and yet to find a way to do this. The Server Admin interface and the command line options I've looked into don't appear to provide this option.
So I actually tried stopping the server, moving the updates from /usr/share/swupd/html to another location, starting the server, the server wouldn't start, moving the files back again, the server still won't start.
1. Does anyone know how you're supposed to "Delete old updates to make space for new ones"
2. Does anyone have any suggestions as to how to get Software Update service running again?
Power Mac G5 Mac OS X (10.4.7)

Does this article contain anything useful?
(16738)

Quota credit on 1st of calendar year for existing employees and for new joinees on prorata basis

Dear All,
we are having an issue in quota generation, where casual leave quota should get credited on 1st of every calendar year and for mid month joiners on prorate basis. If we select calendar year it is crediting on 31st of calendar year, but we need it to be credited on 1st of January and also checking the prorate condition for new joiners.
So please guide on whether it is possible through standard or any work around solution. If so how can it be achieved.
Thanks
Vijaya

Hi,
check this one prorate basis -
http://scn.sap.com/docs/DOC-52928
for you quota on 1st day of calender year, check the settings in the table V_T559L
- Validity/deduction interval
- Validity period for default values
Best Regards.

ISSUE in basic pay arrears wage type for new joiners

Hi Experts,
I am facing an unusual issue as after executing payroll for new joiners from previous month(example: joining date 25.01.2015 & payroll execution date:28.02.2015) results not reflecting arrears wage types of basic pay but reflects /552 wage type and /ZF5 PF arrears wage type.
But this issue is not happening in case of salary revision or other action which affects salary from retro date ie. basic pay arrears wage types are reflecting in RT table.
Already analyzed similar existing discussions in the forum.
Kindly help me to get it resolved.
Thanks & Regards
Bindu...

As mentioned earlier check the parameters for payslip to bring the arrears on payslip, For your reference check the below image where similar case employee is joined in the month of January and payroll is executed in the month of Feb with arrears same wage types will appear on payslip this is standard functionality of SAP you can find out in the image with * with out * * indicates arrears.
let assume your basic pay is XXXX when arrears are there then another line appears with *XXXX indicates arrears similar to your case joined in the month of January and payroll executed in the month of February then one month arrears appear on payslip like above for each wage type.
This is completely integrated with payslip design and PC00_M40_CEDT parameters which we are using for Remuneration statement variant.
I hope you understand.
Regards
Venkatesh

I want the cursor to be in the address bar when creating a new window; it works for new tabs and in a new private window, but not in safe mode.

I have tried following the advice offered in the few different threads I have found on this but nothing fixes it. I want the cursor to be in the address bar when I open a new window and/or when firefox opens without restoring a previous session. I fixed the issue for new tabs via about:config but this doesn't work for new windows. I tried safe mode and the problem persists. In new private windows the cursor is in the address bar.

The search box in about:home steals the cursor. Changing your home page to something else will cause the cursor to start in the address bar for new windows.

Helpful hints for new Creative Zen MP3 2/4/8/16/32 GB (flash) Users On

Summary of helpful hints (from this forum and me) for new Creative Zen MP3 2/4/8/6/32 GB (flash) Users Only!
Rev..
Date: 4/28/2008
Author: ZenAndy
Creative terminology:
MP3 Player Recovery Tool - A program that resolves the majority of player problems quickly.
One click is all it takes to update your player to the latest available firmware, and to give your player a clean bill of health.
Link: http://www.creative.com/products/mp3...me.asp region=
Note: You can also go to "Creative" "Support" "downloads" choose your MP3 Player type to obtain the latest firmware and software releases.
Note: On your Zen you can look under "System" & "Information" and then compare the firmware download
releases OR you can have the "MP3 Player Recovery Tool" (above) do it for you automatically.
Note: Creative Zen 4/8/6 GB "MP3 Recovery Tool" DOES NOT stop on a firmware comparison match.
Note: All firmware releases/revisons for the 4/8/6 GB Zen also works (is the same as) for the 2 GB & 32 GB Zen.
Recovery Mode - If you experience one or more of the following symptoms, it is recommended that you boot the player into its unique Recovery Mode, and then clean up, format or reload the firmware.
. The player is not detected in Creative MediaSource or Windows Media Player
2. The battery does not last as expected
3. Your computer stops responding during file transfers
4. There is a power outage during file transfers
5. There is an error about firmware
6. LCD displays a "Firmware Problem" message
7. Your player is not responding.
8. The player is performing erratically.
Getting Started
. Load your Creative Zen software from CD FIRST and BEFORE plugging the Zen MP3 player, using the short cable, into the PC USB port to charge it.
2. Try charging the Zen MP3 player directly from the USB port on the PC. If not, make sure the USB Hub you are using is adequately powered to provide full charging current to the Zen player. Also, try to have the Zen MP3 player as the only USB device, if possible, on the USB hub.
Some/most Creative Zen flash MP3 Music players come "fully discharged" so, in the mean time, just read the manuals.
FULLY charge the Zen MP3 player for several hours (~4.0 hrs max) until the battery symbol is NOT flashing AND the battery symbol/icon has a small plug/key symbol in the middle.
After the first full charge - additional charging is much quicker about 2 /4 hours. (From 0% empty to full)
3. Go to Creative/Support/Downloads and check for the latest software releases for the Creative Zen. Then check on your Zen MP3 player under System/Information for your firmware revision. Make sure you have the latest software downloaded on your PC and firmware on your Zen MP3 player. < Latest revision [.2.0] 28Feb08>
OR
You can run MP3 Player Recovery Tool - see above.
4. In some cases you might have to do the Recovery Mode "paper clip reset" to get the Zen MP3 flash player started.
See the Zen User's Guide FAQ. The paper clip reset hole is on the bottom edge below the music pause/run switch.
(Not the slotted mic hole on the top edge of the player near the earphone jack and SD card slot!!!)
5. My preference is to have the player shutdown/off before inserting and removing the earphone/headphone plug.
Recovery Mode Using The Paper Clip OR
Alternati've Method For Recovery Mode Without The Paper Clip.
Why use it's
If you experience one or more of the following symptoms:
. The player is not detected in Creative MediaSource or Windows Media Player
2. The battery does not last as expected
3. Your computer stops responding during file transfers
4. There is a power outage during file transfers
5. There is an error about firmware
6. LCD displays a "Firmware Problem" message
7. Your player is not responding.
8. The player is performing erratically.
Save a copy of your player's content, if possible, before cleaning up the memory!
Recovery Mode Using The Paper Clip Reset Method
#. Turn off player if not already turned off
#2. Press/hold play/pause button. If you accidentally release
the button, start this reset procedure over again.
#3. Gently push the end of a metal paper clip into the reset hole on
the botton edge below the play/pause switch.
(Do not use the slotted mic hole at the top edge near the earphone jack)
#4. Slide the on/off/lock switch towards the on position - slide it to the botton hold
until the display lights up and then release.
#5. The recovery mode screen appears and four menu items are shown - see below
<Alternati've Method For Recovery Mode Without The Paper Clip>
#. Turn off player if not already turned off
#2. Press/hold play/pause button. If you accidentally release
the button, start this reset procedure over again.
#3. Slide the on/off/lock switch towards the on position - slide it to the botton hold
until the display lights up and then release. Be patient and wait!
#4. The recovery mode screen appears and four menu items are shown:
< Clean Up> - cleans, rebuilds and reorganizes your player's memory and restores it to optimal efficiency.
When the cleanup is complete, select Reboot. Your player restarts and starts rebuilding its music library.
Note: Your player's firmware is reset to default settings after your player's memory is cleaned up.
Note: This procedure the hide/show password is reset.
<2 Format All>- Warning - Formatting your player erases all content on your player's memory and resets your player's firmware to default settings. If possible, back up all data on your player before proceeding.
Also, you can do this from the PC see Zen User's Guide. FAQ
<3 Reload Firmware> - Caution !!!! Selecting Reload Firmware erases your player's firmware.
DO NOT select Reload Firmware unless you have downloaded a newer firmware version for your player, or have been advised to do so by Creative Customer Support.
Note: My advice when loading/replacing firmware is to connect directly
to the PC USB port without using a USB hub.
<4 Reboot> Restarts the player just like the "on/off/lock switch" when switched ON.
Note: Having NO battery energy/charge/juice this procedure will not work.
Lithium-Ion Polymer Battery Hints
Ref:
http://www.omnica.com/omniview_electronics2.htm
http://en.wikipedia.org/wiki/Lithium_ion_battery
. Allow the battery to completely discharge from time-to-time then recharge it fully.
2. Lithium-Ion batteries loses about 5%- 0% capacity per month.
3. Lithium-Ion polymer batteries have about 300-500 discharge/charge cycles.
4. A half full battery indication (50% @ /2 the battery color) used up about 24 hrs worth of battery. Below 50% the indication goes fairly fast to the max of 30 hrs. Note: The battery level indication seems non-linear through out its range.
5. Battery is Empty~0% - warning screen will appear on LCD and player might shutdown.
6. Battery is Full- 00% with battery symbol NOT flashing AND plug/key symbol in the center of the battery.
7. It takes about 2 /4 hours to charge the battery from empty to full.
8. It takes about 4 hours max to charge a "New" Zen player shipped from the factory.
9. There is a battery manufactuer's failure rate, which is normal ~ % or less, in which the Lithium-Ion Polymer battery refuses to charge. Creative, ships the Zen MP3 players with some or no charge so there is very small probability that you could have one. I call it the "Deep Six Discharge Battery" Contact/call Creative for replacement.
Documentation
There are several pieces of documentation you might need to read to fully understand and use your Creative Zen MP3 flash player to its fullest capabilities.
#. Zen Users Guide "English" - For Zen MP3 Player - download from Creative/Support/Product documentation
#2. Zen Quick Users Guide /Front/Back - download from Creative/Support/Product documentation
#3. Sync Manager (Creative Zen) Click on sync symbol on PC task bar then help
#4. Creative Zen Media Explorer - Just look under the main help menu
#5. Windows Media Player <if used>(Microsoft)Use the help files with this program.
General Tips to increase/decrease the playing time on your Creative Zen flash player.
<Creative Battery Spec: 5 Hrs. Video & "UP TO" 30 Hrs. Audio/Songs>
Please do the following:
. Volume control lower/higher - higher volume settings will decrease playing times. This is logical. More output "volume power" decreases the battery juice.
2. Audio Settings: EQ, Smart Vol, & Bass Boost will effect your playing time but I believe they are not critical as the Volume & Bit Rates(28 kbsp and others) / File Format (MP3,WMA) & Lock Switch.
3. Bit Rates & File Formats Do Matter. Bit Rates and File formats will increase/decrease your playing time.
Per Catherina-CL
"WMA files will use up more power than MP3 files, and higher bitrates more so than standard ones (like 28kbps MP3). Best thing to do is rip an album in 28kbps MP3 and leave it playing in a loop on a normal volume level. See how long the battery lasts then."
Please Note: The main difference between MP3 and WMA is the compression. According to Microsoft a 64KBPS WMA file is the same quality 28KBPS MP3. This is of course up to a person's preference but you may find you can get better compression out of WMA.
4. FULLY CHARGE your Zen. This means the battery symbol is NOT flashing AND there is a plug/key symbol embedded within the battery symbol. The battery is 00% FULL under BOTH conditions. Having just the battery symbol all green will not do it.
From the link:
http://www.omnica.com/omniview_electronics2.htm
Regarding lithium-ion shelf life, one of our engineers recently met with a battery-house representati've. It has come to their attention that repeated charging and re-charging of a less than fully discharged Li-ion cell affects the battery "gas gauge" included with many devices. Over a number of cycles there is a resultant loss in accuracy. Frequently, the indicated remaining charge has little relationship to the actual amount of life left in the cell! Fortunately, according to the battery expert, the gauge will reset itself if the battery is allowed to completely discharge from time-to-time.
5. Having different types of earphones/headphones will increase or decrease the playing time by how much "electronic load" the earphones/headphones create on the Zen player. There are some power hungry earphones/headphones out there.
The 6 ohm earbuds conserves battery power more than the 32 ohm earbuds supplied by Creative. (About 0% more)
6. Always, always lock your Zen player while playing music. This cuts off the power drain from the color 2.5" LCD and blank the LCD screen. After all, you can't read the LCD screen if it is in your shirt pocket and playing music!
7. Make sure you have the latest firmware upgrades in order to get the best of your Creative Zen Flash MP3 Player.
Troubleshooting
Your Creative Zen is extremely complex.
Check this link to peek inside player http://www.anythingbutipod.com/archi...isassembly.php
Also, this link:
http://arstechnica.com/journals/hard...ssor-behind-it
There could be a million things that could go wrong with your player so you will not be the FIRST or LAST to have a problem. Keep in mind, there are many, many others that have the Zen with no problems whatsoever. Things happen, but Creative is there to help.
Dropping a Zen or any other player might/will/possibly ruin the player for good!!!
Since this player is solid-state (no moving parts e.g. mini-disk dri've) then the only thing that will keep it from running for years is the non-user replaceable Lithium-Ion battery. I will concentrate on some troubleshooting tips which are battery related but I hope you have already the latest firmware downloaded and installed on your player
Battery - Lithium-Ion Polymer
#. Battery won't charge "out of the box" new player.
A. First, read above "Getting Started"
B. Next, try a different USB mini cable.
C. Next, there is a battery manufactuer's failure rate < %, in which the Lithium-Ion Polymer battery refuses to charge.
Creative, ships the Zen MP3 players with no charge so there is very small probability thatyou could have one.
I call it the "Deep Six Discharge Battery" Call / Contact Creative.
#2. Battery won't charge properly after using the player for some time.
A. When you plug in your player into the USB port via mini USB patch cable, the connection resets the player to the "docked screen" with the battery level gas guage , in the right hand corner.
Sometimes this action does not reset the player properly but there is no indication to you that the player is charging.
Just disconnect/connect the USB cable again.
B. Sometimes, the Zen player gets confused and you have to do a Recovery Mode "paper clip reset" which forces the player into a "special menu screen" to clean-up the player and to reset the player which allows showing the "docked screen" while charging the unit. See Zen User's Guide for explicit instruction und FAQ.
C. Since the Zens came out late in 2007, the maximum of 300-500 charge/discharge should not apply YETbut users beware, as with any other Lithium-Ion Polymer battery it will not charge fully "like new"because of a " fixed shelf life" (2-3 yrs) OR too many charge/discharge cycles. A battery replacement is in order.
Methods of charging the Creative Zen MP3
. The short mini-standard USB cable provided by Creative from the factory. Plugs into a PC USB port.
2. Uni'versal Power Adapter (Creative) plugs into the wall. Works "anywhere in the world"
Note: Different countries have different wall AC voltages and hertz requirements. This has adapters for different countries/locations wall outlets and a uni'versal power supply for all voltage and hertz requirements.
Note: This is a heavy duty high/fast charging wall outlet charging adapter. (2400 ma)
3. Auto/Vehicle 2 VDC charger (Creative) or other compatible vehicle 2 VDC to USB charger.
4. EARHUGGER IPOD POWER POD - MP3-8370 (White compact module)
http://www.earhugger.com/powerPod.html
http://www.amazon.com/Earhugger-MP3-.../dp/B000QTTKSS
This compact module will solve all the following travel modes and conditions:
. Camping, hiking or outdoor travel - no PC or noAC or maybe no auto/car.
2. Airplane travel - no PC or no AC or no auto/car.
3. Train/subway travel - no PC or no auto/car
4. Car travel - no PC or no AC
5. Foot travel - no PC or no AC or no auto/car
It uses 4 ways to charge the Zen:
. Retractable mini-standard USB cord for PC charging. <--- does not communicate with PC! - only for charging
2. Retractable mini USB cord for auto/vehicle charging (Fused)
3. Retractable mini USB cord for wall 0-20 VAC 50/60Hz charging. (non-international use plug style)
4. 9 VDC battery terminal for using standard alkaline 9 VDC or high ma Lithium 9 VDC to charge the Zen via
mini USB cable. Note:You might need several alkaline batteries to charge the internal 550 ma hr Zen battery!
Great for remote destinations.
5. Rechargeable portable battery packs.
Black & Decker has several "Power To Go"models CPI0B-C & CPI20XB (not for international use because of 20 AC 60Hz only charging wall wart)
Note: There are other brands that also do this method of charging.
http://www.blackanddecker.com/Produc...Path=4033.4040
You charge this portable NiMH battery pack from the AC wall outlet so you can carry with you on trips to charge the Zen.
6. Mobile phone chargers. Some have a mini-USB plug for charging the phone but it could be used to charge the Zen BUT BEWARE IT COULD RUIN THE ZEN IF IT IS NOT COMPATIBLE! The output should have a voltage of 5 VDC +- 5% (4.75-5.25 VDC) ON THE PROPER MINI-USB PINS and a charging current at least 200 ma to 2400 ma. See this forum for the recommend phone phone chargers to use with the Zen.
Note: You are charging an internal Lithium-ion polymer 550 mahr battery in the Zen so the lower the charging current the longer it takes to charge.
Note: You will find that charging the Zen from the wall charger is much faster than the "current limited" charging on the standard PC USB port.
Note: For diagnostic purposes and emergency charging of the Zen it is wise to have an external (non-PC) charging device for your Zen.
Note: Only the battery charging symbol shows up on the Zen when using an external charger.
Scratches
All plastic screens will scratch, doesn't matter which type you have.
For minor scratches you could use the Novus three part cleaner, polish and scratch remover system. Do not use the #3 coarse abrasi've in this system! Be extremely careful in using this product !!!! Please check the web.
OR
Low abrasi've toothpase <--- some say this works
OR
CD scratch remover/repair kit <---- have not tried this.
The Zen (Flash) MP3 glass LCD screen is covered by the overlay plastic you see on the front. Worst case, you can have only the outer shell repaired and replaced by Creative.
To prevent scratches in the first place:
Use the Zen cloth bag which comes with the unit (sometimes ) to prevent scratches.
OR
Buy the Zen clear plastic case (Clear Case #70AB2600002). Sold by Creative.< I use this>
OR
Buy an clear plastic overlay. (Screen protector #70AB2600003) which goes over the LCD protector screen for protection. Sold by Creative.
OR
Also, you can cut up a "generic" PDA screen protector to fit the Zen.
OR
Obtain a "digital camera lcd screen protector" from a camera store or internet
OR
"Invisible shield" -The best protection money can buy
http://www.zagg.com/invisibleshield/...ns-shields.php
How to destroy your Zen - WHAT NOT TO DO
. Leave it in the auto/car/vehicle - the vehicle inside heats up 20-35 F higher than the outside temperature.
2. Leave it outside in freezing temperature 0C 32F. The LCD will freeze/discolor/absorb water.
Note: It is remotely possible it could recover when warm-up at room temperature.
Note: Just keep the Zen near your body heat when outside in freezing temperatures.
3. Dropping it might cause the LCD screen to crack or loosen up the internal connections to the electronics or short out the internal electronics.
Note: Use a protecti've case to cushion the blow from dropping the Zen.
4. Dropping or submerging or getting the Zen wet in water might short out the electronics and battery.
You could prevent destruction by immediately shaking the Zen vigorously in open air to dry it out.
5. Sitting on it could flex the electronics and short or open circuits which would cause a defecti've/faulty Zen.
<A bit of humor ... There is No Santa Claus, Easter Bunny or Tooth fairy and Creative does NOT give away money. If you destroy or damage your Zen you will pay not Creative>
How can you tell if your Zen is defecti've/faulty
. A "white screen" or a "totally blank black screen" shows up on the Zen LCD.
2. You cannot force the Zen into the special "Recovery Mode" menu screen.
3. The Zen refuses to "take a charge"(To charge up the internal Lithium-Ion Polymer battery)
4. The Zen LCD is cracked or distorted due to dropping or handling abuse.
5. The Zen clock does not keep accurate time (within 2 mins max per month)
Contact Creative if any of the above faults occur - the Zen is bad and nothing you can do will fix it!
WSOD "White Screen of Death"
The "White Screen of Death" is really caused by a hardware problem. You see, the internal Freescale/SigmaTel STMP3700 MP3 processor has to write to the LCD. If this operation is prevented by internal electronic opens or shorts, bad STMP3700, locked-up firmware, bad LCD or any other electronic component failure then the CPU might/will halt and refuse to write to the LCD which will be reflected in a "white screen of death" I cannot cover all the causes of the "white screen of death" but rest assured Creative should pick these problems up in their quality control manufacturing process with a 99% success rate. Problems do show up after the manufacturing process but Creative has warranty protection for this other % fault rate. (Which is normal in electronics manufacturing)
Media Content
Listening to the built-in music on the Zen is OK but after a while your question now becomes "What else can I do with my Zen "
Note: The "How to" instructions for adding Media content can be found in the Zen documentation.
Terminology:
Album: Collection of tracks or songs under one "album" title.
Artist: Track or song artist
DRM: Digital rights management - copy protection scheme - Zen cannot use music with this music protection scheme. (itunes) (But "itunes plus" will work)
Genres: Type or kind of music
<The following genres are defined in ID3v>
Blues,Classic Rock,Country,Dance,Disco,Funk,Grunge,Hip-Hop,Jazz,Metal,New Age,Oldies,Other,Pop,
R&B,Rap,Reggae,Rock,Techno,Industrial,Alternati've ,Ska,Death Metal,Pranks,Soundtrack,Euro-Techno,
Ambient,Trip-Hop,Vocal,Jazz+Funk,Fusion,Trance,Classical,Instru mental,Acid,House,Game,Sound Clip,
Gospel,Noise,AlternRock,Bass,Soul,Punk,Space,Medit ati've,Instrumental Pop,Instrumental Rock,
Ethnic,Gothic,Darkwave,Techno-Industrial,Electronic,Pop-Folk,Eurodance,Dream,Southern Rock,
Comedy,Cult,Gangsta,Top 40,Christian Rap,Pop/Funk,Jungle,Nati've American,Cabaret,New Wave,
Psychadelic,Rave,Showtunes,Trailer,Lo-Fi,Tribal,Acid Punk,Acid Jazz,Polka,Retro,Musical,Rock & Roll,
Hard Rock
<The following genres are Winamp extensions>
Folk,Folk-Rock,National Folk,Swing,Fast Fusion,Bebob,Latin,Revival,Celtic,Bluegrass,Avantg arde,
Gothic Rock,Progressi've Rock,Psychedelic Rock,Symphonic Rock,Slow Rock,Big Band,Chorus,
Easy Listening,Acoustic,Humour,Speech,Chanson,Opera,Cha mber Music,Sonata,Symphony,
Booty Bass,Primus,Porn Groove,Satire,Slow Jam,Club,Tango,Samba,Folklore,Ballad,Power Ballad,
Rhythmic Soul,Freestyle,Duet,Punk Rock,Drum Solo,A capella,Euro-House,Dance Hall
<A bit of humor: I think the above Genres lists are missing two - "elevator music" & Crying and Whining e.g. Country Western>
ID3 Tags: Internal file information associated with an Mp3 or wav audio file. This format contains
Track number, Album name/title, Genre, Artist and Song Title which can be sorted and indexed by
the Zen device.
IPTV: Is a system where a digital television service is deli'vered using Internet Protocol over a network infrastructure, which may include deli'very by a broadband connection. http://zencast.com/
JPEG: Is a commonly used method of compression for photographic images.
This is the only photo format used by the Zen.
MP3 and WMA music tracks: Music format used by the Zen.
Note: Having the wrong bit rates will drain the Zen battery faster. (See above)
MP3: Is a digital audio encoding format using a form of lossy data compression.
Non-protected AAC: Files are regular AAC files without any DRM: they can be converted to other formats (like MP3) and can be played on an unlimited amount of devices and burned an unlimitd amount of times. They have no restrictions.
Podcast: Is a series of digital-media files which are distributed over the Internet using syndication feeds for playback on portable media players and computers. http://zencast.com/
Protected AAC: Files are AAC audio files that contain DRM (Digital Rights Management), most often music purchased from the iTunes store. The Creative Zen cannot use these files.
Note: "Itunes Plus Store" have songs without DRM which the Zen can use.
Ripping CDs: Copying tracks from an audio CD on a PC and downloading tracks to the Zen.
Note: Use the Creative Zen Media Explorer for ripping audio CD is one method.
Song Title: Name of song or track
Track Number: Numerical number of track of CD album.
Track: General name for song or song title.
Unprotected AAC format: Music format used by the Zen
WMA:Is an audio data compression technology developed by Microsoft. The name can be used to refer to its audio file format or its audio codecs.
WAV: (or WAVE), short for Waveform audio format, is a Microsoft and IBM audio file format standard for storing an audio bitstream on PCs.
Note: The Zen's built-in microphone produces this audio file format.
Zen Audio Format:MP3, WMA, WAV, non-protected AAC (.m4a), Audible (2, 3, 4)
Zen Media Content: Video, Music, Audio, Photos/Images transferred/dowloaded into the Zen
Zen Photo Format:JPEG
Note: You can copy/drag/paste JPEG photos from your PC to your Zen for viewing.
Note: You can import photos & view photos from the SD card.
Zencast Organizer: Seamlessly integrates ZENcast media files with Creative portable media players and/or your computer
Zen Video Format:MJPEG, WMV9 and (with transcoding - MPED4-SP, DivX 4/5 and XviD)
Warning - In some countries (including the US) its illegal to do:
Copying audio DVD & DVDs
Defeating DRM MP3 Music (Digital Rights Management)
Intercepting/copying (non purchased) music.
Downloading music/songs from an illegal or "free" rouge website.
General Media Content links:
http://pro-music.org/Content/GetMusi...lineStores.php
Note: Check to see if your music files/tracks contains ID3 tags.
Note: ZEN also supports iTunes Plus tracks from the iTunes store,
Note: The following media content is only a small fraction of means and ways
of collecting/dowloading media content to the Zen.
Media Content from Creative Website(s)
Note: The Media Content can be found under "Fill your Zen" on the bottom of the Creative Zen product page.
http://zencast.com/
ZENcast is the ultimate source for free IPTV channels, video blogs and podcasts on the Internet. It provides quick and easy access to a wide range of interesting and entertaining video and audio content online.
http://www.audible.com/adbl/site/cre...seBVCookie=Yes
Audible.com - Audible.comis the Internet s leading audio provider of bestselling audio books, comedy programs and today s most relevant magazines and newspapers
http://creative.vongo.com/
VONGO is the video download service that gives you instant access to over 2500 hit movie and video selections from Starz .
Watch movies whenever, wherever on your ZEN. A great entertainment venue for watching movies while on the road or on the go.
http://www.napster.com/creative/
Transfer unlimited music to your ZEN without paying per song.
With Napster To Go you can:
Choose from over 5 million songs, plus new releases every week
Play music instantly from any internet-connected computer
Find old favorites and discover new music by exploring playlists, radio, Billboard charts and more
Create a library of your favorite music and build custom playlists.
http://www.emusic.com/ZEN
Choose from over ,500,000 songs
Burn unlimited CDs
Compatible with every MP3 player
No confusing restrictions-Own your music!
http://www.lala.com/frontend/action/...=user:2672@223
Why pay 99per song when you can get the whole album for $At lala.com, you can trade your used CDs for new music.
.8 million titles available for trade. CD quality guaranteed.
Every CD you receive is yours to keep - no restrictions.
Pay only $ per CD received. No monthly fees or commitments. Sign up is FREE.
http://www.amazon.com/b/ &node=62663
Buy or Rent Movies Online
Watch DVD-quality video downloads on your PC or ZEN
Conveniently download from your PC at work to your PC at home
Discover thousands of TV shows & movies available for download
I started this thread in April 08 to help other new Creative Zen MP3 (Flash) users. If there are common threads that are posted from new users then I try to make a section to inform other new users in solving their similar problems. I cannot believe that this thread was viewed over 0,000 times! Thank you for your "viewing" support.
Please note: This thread is constantly changing so check back for any new helpful hints, problem solving, troubleshooting and practical solutions for the Creative Zen.
"The Creative ZenR O C K S"
Zenandy
Message Edited by Zenandy on 08--2008 08:26 AM

Hi,
I'm from germany so no 'best buy' but I think I will lock around sleeve/bag for a different product with same measures. Any tip?
The clear plastic case is not what I want. I would like to use the player without such protections. I just want a sleeve to protect the player while its in my jacket/pants.
Btw, i have bought this version: Creative Zen (maybe european version?). I also doesn't seem to have your mentioned sleeve. I also couldn't find it on the website.
Anyway, thank you,
Chris

Reset encryption password for NEW iPhone backups

Hello Everyone,
I have an iPhone and iPad which are currently working perfectly. However during testing I figured out that I somehow lost my iTunes backup encryption password. As such I figured I would just change the backup password, delete the old backups, and create NEW backups for which I do know the password to and all would be good (and ready for a future device failure.)
However it appears that iTunes will not allow you to change or disable the encryption password for NEW backups without first knowing the old encryption password. Does anyone know if a way around this?
Thank you for your time.

Thanks!

Upgrade from 8.2 to 8.6 for new ASA 5515X

Hello,
My customer has a rather complex configuration on an ASA 5510 running version 8.2
They are migrating to new ASA 5515X models which of course only version support 8.6
How can i convert the configuration from 8.2 to 8.6 since the new ASA's do not support the earlier versions?
The X series seems to be a great option for new deployments but what about replacements of existing older models?
Thanks for any ideas everyone!
Chris

Hello,
I would say go to 8.4 From there you will have the same syntax.
There will be new commands and features on 8.6... That for sure but you are going to be on the same path.
Any other question..Sure ..Just remember to rate all of the helpul posts
Julio

Migration of balances for new ledger using the New GL

Hi everyone,
I have a specific scenario into this customer where we have implemented the SAP version ECC6.0 with the table FAGLFLEXT is active and using just one ledger (0L - standard). We need to create a new ledger for IFRS (e.g: 1L), as the customer didn´t use the splitting document functionality, it was not purchased the migration services.
Now I need to upload the balances in the accounts into new ledger, I understand that for general accounts there is no problem because I can use the transaction FB01L and specifying the new ledger (1L).
My doubt is : How can I to do the upload balances for open items into the AP and AR accounts?
Anybody can help me?
Thanks
Ricardo Gomes

You are right. I just realized that and came back to update my response. Please see the following note.
https://service.sap.com/sap/support/notes/1070629
I see a standard program delivered for that purpose in the note above.
FAGL_MIG_SUBSEQ_POST
Again, please go through the note. There is a lot of information on data transfer (and other FAQs) for new non-leading ledgers.

Report Painter for New GL

Dear experts,
I need to create a custom report with ReportPainter with the data you see with t.FAGLB03.
Since there are no standard reports for New GL, to copy and modify, i created a library by copying the library 0FL (Table FAGLFLEXT) and i stopped after :(. For example, "Lead column" must be a hierarchy of profit centers. In the "Element definition" i added "Name" - "Profit Center" and chose "Characteristic is Interpreted as Set / Hierarchy," and "Characteristic is Interpreted as variable. In the list of "Value of variable" for the "From" there is no variable that refers to the table FAGLFLEXT, PRCTR field.
What should I do? I create all the necessary variables with T.GS11, or is there an easier way? Can I use something existing?
Please, can you give me an explanation step-by-step what I should do. Any advice is welcome!
Thank you in advance.

Hi Serena,
As stated you can create your own reports using the standard SAP library 0FL
you do not need to create a custom library.
One tip I have is that If you are creating reports with the Profit Center scenario active then
you can still use transaction code KE5B to copy your Financial Statement Version (FSV) groups to EC-PCA.
Even though your reporting source will NOT be EC-PCA in the New G/L, this method can still be
used as a short cut to create account groups that can be referenced as sets in Report Painter.
I used this method in the lead column for "Account Number" to easily generate a FSV style report
in report painter in the New G/L with the profit center scenario activated.
- Good Luck

How do you get your experts with negative stance for new things / innovations to HANA

We have over 50 ABAP developer (senior experts). Primarily we develop in the old core module (SD, MM, FI, CO, HR, PP, CS, IH, PS) on ERP systems / business suite.
We have three groups of developer:
Group 1: They can’t await to work on new architectures – they’re open for all and have fun to work as a pioneer and dig in the deep of the system
Group 2: For this developer it’s all the same – for this people it’s not a problem to go to a other architectures
Group 3: They have no interest
to work in new architectures
to spend time to learn new things
they are very closed for new things
they have for all topics bad statements
I am part of the group 1. In my opinion in the IT it’s normal to spend much time at new topics in free time to keep up to date. New topics / innovative things make the developer job very exciting. For me it’s regular process – and that’s my own passion .
Since two month we have our own HANA system in our data centre as play field :-) (business suite on SAP HANA). I’ve some colleagues who made the HANA certification – and we made the first steps in our system. For group 1 and group 2 everything is okay and they’ve fun .
We have problems with the group 3. They find every hair in the soup – they spend very much time to search arguments against HANA. That’s our “negative group” . We copied our SAP System to a new system and made a technical migration. Now they compare the SAP System, which is based on an oracle datebase, with the new SAP System which is based on a HANA System. They go through the standard ERP process (offer / order / purchase order / goods movements / delivery / MM invoice / SD invoice / material master data / customer master data / vendor master data / conditions / financial bookings / etc.). They main argument is, that they can’t see a grow up of the performance / the added value of the invest / etc. Our other problem is that the group of this people have experience over 20 years in ABAP developing – and their opinion have a high weight. The other arguments: IBM and oracle are working on similar architectures – and we can hold on on the open sqlsyntax / on the present coding.
Have you similar problems to get the acceptance of group 3?
Have you tips / tricks for us?
Have you ideas for catching the group 3?
What standard components are really optimized for HANA?
In which standard components can we see a really performance grow up?
There are standard use cases to see the differences?
Which data volume do we need in the data model to see the differences?
What can we do to take the group 3 with us?
How can we open the group 3 for innovations?

Hi,
Please find my reply below.
1. Have you similar problems to get the acceptance of group 3?
In IT world we have similar groups. Only results help this group3. I would suggest showcasing on results.
2. Have you tips / tricks for us?
As you mentioned in your email, you already have HANA System to play with. So I would suggest looking at high performance transactions like MRP run and FICO Month-end Close.
3. Have you ideas for catching the group 3?
SAP has few use cases. Take-up these use cases build data models and use in ERP.
4. What standard components are really optimized for HANA?
Recently in our organization we replaced database from DB2 with HANA. Now our SAP ECC is running on HANA. Straight away we have seen 30% of performance improvement in all the transactions. SAP is providing optimized SAP Transactions and there is significant performance improvement and SAP Road Map clearly talks about providing more optimized SAP Transactions on top of HANA to its customers.
We tried to push some of our high performance code to DB layer by creating the Data Models and using those views in SAP ABAP Programs or Transactions. This gave us significant performance improvement.
Please refer to below document. This has list of standard optimized transactions.
Link
5. In which standard components can we see a really performance grow up?
This blog throws light on following high performance transactions.
Link
6. There are standard use cases to see the differences?
Use Case
7. Which data volume do we need in the data model to see the differences?
MRP run transaction has huge performance issue you can work on MRP Run data model.
8. What can we do to take the group 3 with us?
Only Proof of Concepts (POC) results will help to take this group.
9. How can we open the group 3 for innovations?
As per your email, I feel group 3 is most demotivated group. I would suggest to talk to each individual and understand there areas of interest and try to put them in their areas of interest. As per my experience this will give good results.
-VJ.

Want to know how to check for new line character in text file

Hi All,
I`m trying to read data from text file. However I`m not sure whether the data is in 1st line or nth line. Now I`m trying to read the text from the readline. But if text is "" and not NULL then my code fails. So I want to know how to check for new line character and go to next line to find the data. Please help.
Thanks
static int readandwriteFile(Logger logger,String filepath){
          BufferedWriter out = null;
          BufferedReader in = null;
          File fr = null;
          int get_count = 0;
          try     {
          if(new File(filepath).exists())
          fr= new File(filepath);
                    System.out.println("FileName: "+fr);
               if(fr != null){
in = new BufferedReader(new FileReader(fr));
                         String text = in.readLine();
                         if(text != null){
                         get_count = Integer.parseInt(text);
                         in.close();
                         else{
                              get_count = 0;
     else{
out = new BufferedWriter(new FileWriter(filepath));
     out.write("0");
            out.close();
               }          //Reading of the row count file ended.
          catch(Exception e) {
               e.printStackTrace();
          finally {
               try{               if (in != null) {
                         in.close();
          if (out != null) {
                         out.close();
          catch(Exception e) {
                    e.printStackTrace();
          return get_count;
     }

You are calling the readline() only once which means you are reading only the first line from the file...
Use a loop (Do-While preferably)
do{
//your code
}while(text == "")

I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add

I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add APN. Now when i switch to safari its showing you are not subscribed for cellular data. But I am able to use data on other phone.
Will you please help me in this regard?
Another issue, since i bought my new iphone there is dust inside back main camera.
Your advises are highly appreciated.

Hey Shaiju isac,
I'd take a look at the following article, it'll guide you though steps to you troubleshoot cellular data issues on your iPhone:
iPhone: Troubleshooting a cellular data connection
http://support.apple.com/kb/ts3780
Cheers,
David

For new PCsuite

Similar Messages

Maybe you are looking for