Forcing iPod Auto connect to the the strongest access point?
I have two access points at home, one on the first floor "platinum 1״ and "platinum 2" on the second floor. How can I force my iPod Touch 4th generation (the newest version) to connect to the the stronger access point?
In many cases I am on the second floor where the wifi signal is stronger from platinum 2 but the iPod stay connected to platinum 1 access point.
I want the iPod to change automatically to the stronger AP at my home.
Please advice
It will stay connected to the current network until the signal strength gets too low to stay connected, then it will switch to another network if available.
Similar Messages
-
I restored my ipod before connecting it to the computar and now it just stays at the screen like when its the silver apple is there a way to fix this?
- Have you tried resetting the Ipod:
Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.-
- Next connect it to your computer. If iTunes sees the iPod restore the iPod, First restore from backup and if problem persists restore to factory defaults/new iPod.
- If iTunes does not see the iPod first try placing the iPod in recovery mode. If not seen try placing it in DFU mode:
Recovery mode:
iPhone and iPod touch: Unable to update or restore
DFU mode:
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
Aironet 1600 - A response was not received from the router or access point
Hi,
I'm trying to set up a wireless network with multiple SSID's. The new network only has CISCO products (router, switches). For the moment I'm trying to connect to 1 SSID (Windekind.Gast). the SSID is visible but when connecting devices have te folowing error message in the log:
Connection status summary
Connection started at: 2015-02-17 09:55:49-951
Profile match: Success
Pre-Association: Success
Association: Fail
Security and Authentication: Not started
Root cause:
Wireless association to "Windekind.Gast" failed
A response was not received from the router or access point.
Detailed root cause:
Wireless association to this network failed. Windows did not receive any response from the wireless router or accesspoint.
The signal is perfect (I'm only a few feet away from the AP).
To make sure there is no dhcp problem I tested the swich port in access mode for vlan 30 which supplied an IP correctly. I'm really not seeing the problem and searched the web for days now! Any help would be very much appreciated!
Below the config of the access point (done via de web interface).
! Last configuration change at 05:30:28 UTC Mon Mar 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2452
no preamble-short
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
endHi Rasika
thanks for the reply! 10.0.0.81 belongs to vlan 1. I changed the config as suggested but no luck.. (same problems are logged in the event viewer). the ap is connected to a switchport in trunk mode and vlan 1 is the native lan (untagged). the port also is joined to vlan 30 (and others).
Below the new config. Hope you can see an error..
! Last configuration change at 22:56:10 UTC Thu Apr 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Default vlan 1
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
no preamble-short
channel 2452
station-role root
payload-encapsulation dot1h
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
t -
How do I set the transition between access points would be fine?
Hello everyone,
We have an organization Wirless controller 2504 with 20 aironet access-point (700 series)
Once I defined all the access points I noticed that the transition between them is not working fine...
I mean that clients can not walk around in our organization without having to connect to any access point separately.
How do I set the transition between access points would be fine?
Thanks a lot (:HI Omri,
which software version you have on WLC ?
Is the site survey done propely ?
Remember: It is the client that decides when to roam and which AP to connect to based on what it perceives the signal to be.
If your site survey design is perfect and still have problems while roaming then:
Disable your lower data rates on the 2.4ghz and or 5ghz radio and your clients will roam better. Try to disable everything below 11mbps. and give that a try.May be old device will work in this case.
Regards
Dont forget to rate helpful posts -
Where can i find the french manual for the Procurve MSM310 Access Point
Hi
I'm looking for the french version of the ProCurve MSM310 Access Point manual.
Where can i find it ?
Thanks in advance
DavidHi, David:
You may want to post your queston on the HP Business Support forum -- MSM Series.
http://h30499.www3.hp.com/t5/MSM-Series/bd-p/wireless-e-series-forum#.U-fngDh0zGg -
Any new firmware for the Cisco AP541N access points.
Do you know if Cisco has come out with any new firmware for the Cisco AP541N access points.
Latest release is 1.8.0 from Jan 25, 2010:
http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=1.8.0&mdfid=282790482&sftType=Small+Business+Pro+Wireless+Software&optPlat=&nodecount=2&edesignator=null&modelName=Cisco+AP+541N+Wireless+Access+Point&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=&hybrid=null&imst=null&lr=Y -
Auto connect using more the one iPhone 4S
MEX-BT3100P will Pair 2 iPhone 4s successfully individually. But will only auto connect from the last paired device. I would then have to go into iPhone setup and select Sony Automotive in Bluetooth settings before it will connect. Now this iPhone will auto connect and the other iPhone will not auto connect. Tried powering off the first paired device completely before trying to auto connect the 2nd device. Still no go. Tried using BT SIGNL but it does not detect the iPhone without going into phone's settings to connect.
What sort of card is it, debit or credit ? If it's a debit card then I don't think that they are still accepted as a valid payment method - they are not listed on this page and there have been a number of posts recently about them being declined. If you don't have a credit card to use in its place then are iTunes gift cards available in your country to use as your payment method instead ?
If it's a credit card then is it registered to exactly the same name and address (including format and spacing etc) that you have on your iTunes account, it was issued by a bank in your country and you are currently in that country ? If it is then you could check with the card issuer to see if it's them that are declining it, and if not then try contacting iTunes support and see if they know why it's being declined : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Account Management -
connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage. -
Help me find the required Wireless Access point
Dear Friends,
I am in search of a access point with below specification, so please let me know that which model has this functionalities.
. Wireless Access Point:
* No of port should be 10Base-T/100Base-TX Ethernet
* Standard should be IEEE 802.11g, IEEE802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af(PoE), 802.1q(VLAN) , 802.1X(Security authentication), 802.11i ready (Security WPA2), 802.11e ready (wireless QoS), 802.11F(Wireless roaming)
* LEDs should be power, PoE, Wireless, Ethernet
* Web Management should be built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
* SNMP Support should be SNMP version 1, 2c, 3
* Operation modes should be access point made, point to point bridge mode, point to point multipoint bridge mode, repeater mode
* External antennas should be 2 (omni directional) SMA detachable
* Security should be WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
* Access Control should be wireless connection control: MAC-based
* Wireless Security monitor should be Intrusion alarms(e.g. rogue client detected, spoofed MAC address) Denial-of-service alarms (e.g. duration attack, association table full) vulnerability alarms (e.g. access point is not using encryption, access point is broadcasting SSID)
* Power should be 12V 1A DC input, and IEEE 802.3af compliant PoE. Maximum power draw should be 3.36WHello Shekib,
All you did was describe the WAP200.
It fully fits in your description.
Please check it and see with your eyes.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10047/ps10048/data_sheet_c78-501966.html
I hope i helped you.
Regards.
Andrey Cassemiro. -
How old is the 1142 wifi access point?
How long was the Aironet 1142 wifi access point in production? When was it first available for purchase?
Few details are over here
http://www.cisco.com/c/en/us/products/wireless/aironet-1140-series/eos-eol-notice-listing.html -
Blackberry Z10 connection with an Aironet Cisco Access Point 1200
Hi everybody,
I'm trying without success a connection between a Blackberry Z10 and an Aironet Cisco Access Point 1200.
We have no BB Server, we would like just to connect the WIFI.
I've checked this points during the activation of the device:
There's no LEAP protocolle.
There's an EAP-Fast possibility.
There's Mac Address recognition possibility.
When we try to use the EAP-Fast possibility, we generate a .pac file, but i don't know where i can put this file so that the Blackberry recognize this file. I've search the whole day and didn't find anything... there's simply no explanation with the Z10 around the .pac file without a BB Server.
I've try the Mac Address recognition and it simply doesn't work (no error the search time is too long)
Every other older smartphones - Blackberry (there's 4 devices) are working.
Anyone have an idea about? a suggestion? a list of compatible WIFI Devices?
Thank you ahead.
Have a nice day.
Joel.Sorry i don't understand your answer.
I'm not a developper but a system administrator.
I just would like to use a Balckberry Z10 with our Wifi/Router Aironet Access Point 1200.
not more.
Best regards,
Joel -
Dear all,
I deployed new Linksys Wireless WAP4410N Access Point and it is working fine. Laptop which is connected to AP can able to access internet. It can able to communicate with AP and also the gateway IP(Router IP) but the issue is wireless devices are not able to communicate between them. In the case LAN device can communicate between wireless devices. Can't able to share files between wireless devices.
Please help me to troubleshoot this issue. Wat could be the issue over here. Wat step i have to take to clear this issue.
Advance in thanks.
Thanks and regards,
Chandhuru.MHi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
Under Wireless/Security how do you have the Wireless Isolation configured?
Wireless Isolation (within SSID) should be disabled to allow wireless computers associated to the same SSID to see and transfer files between each other
Thanks
Eric Moyers .:|:.:|:.
Cisco Small Business US STAC Advanced Support Engineer
CCNA, CCNA-Wireless
866-606-1866
Mon - Fri 09:00 - 18:00 (UTC - 05:00)
*Please rate the Post so other will know when an answer has been found. -
Problems connecting WRE54G with DLINK DWL2100AP Access Point
Please help!!
Hi there,
Your dlink device, is it an access point?
Your range expander, is it version 1 or 2?
Check the wireless settings of your access point and set in the range expande. They need to be exactly the same.
Hope this helps.
"When love and skill work together, expect a masterpiece." -
how do you know which updates you need for your a second generation ipod touch. I havent used my ipod touch in forever and now no matter what i do no matter how many times i restart everything it still wont show up in itunes or my pc when its connected it charges but thats about it. ??
Did you do everything here:
iOS: Device not recognized in iTunes for Windows
Including Remove all reinstall ALL Apple software)
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
New cable and different USB port?
Runs this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Try on another computer to help determine if computer or iPod problem -
Hi I recently upgraded with a new computer. I see that when I open my itunes that my old playlist did not transfer to the new computer. I want to transfer my paylist from the old computer to the new one without loosing what I have on my IPOD Nano (7th Gen) at present. I saw that you can link the IPD directly to te computer and download the playlist to my new computer. Okay so I just hook in directly once I have it set up what do I push to transfer the playlist frommy IPOD to the computer> A by-the-number explanation would be appreciated as I am not computersavy and over 60. Thanks
Welcome to the Apple Community.
I'm not entirely sure if this is what you mean, but the following User Tip may help you.
Recover your iTunes library from your iPod or iOS device.
Maybe you are looking for
-
Exchange Online Plan 1 use with Office Home and Business 2013 License
Question: Does the Office Home & Business 2013 Outlook work properly with Exchange Online Plan 1? (are there limitations?) As a farm dealership needing 44 licenses (very light Office product use except email), I'm struggling with the sustaining cost
-
ITunes can't open - because of QuickTime?!
Hi, recently when I try to open iTunes, I get the notorious "iTunes has encountered a problem and needs to close" error message from windows. The error report is as follows: AppName: itunes.exe AppVer.:6.0.0.18 Offset 0000b77d Now, I did do research,
-
Do we require an OLTP DB and Data Mart?
Our data sources are as follows: - An mdb file (downloaded every hour) - Multiple xls files (downloaded every week) Our aim is to develop a BI solution using BISM, Data Mart, OLAP cubes etc. From my understanding, we do not necessarily require an OLT
-
Cannot print color from pdf correctly
Hello , i have hp designjet roll 111 when print any thing form autocad i can print fine and good resolution but when try to print form pdf i can print but the resolution for color not clear. i am installed latest driver and update acrobat reader and
-
ResourceBundle - French characters
I have a Swing application that I want to internationalize. I.E. I want to have an English resource bundle, and a French resource bundle. I created the two resources files and I've placed them in the classpath, I then load the files like this ( for t