Formatting drive with Airport Extreme with Encryption?

How can I format the Hard Drive so it is still encypted and attach it to the Airport Extreme?

Have you tried restarting the devices involved and giving them all a fresh go?

Similar Messages

Cannot see OS Extended-formatted drive on Airport Extreme in Finder

*EDIT: solved

I just purchased two 500GB USB hard drives and am attempting to connect them to my AirPort Extreme Base Station. They are connected to the USB port of the AEBS via a powered USB hub.
When I turn them both on, the base station goes into a restart loop. That is, it continually restarts until I power off both drives. If I turn on just one drive, it doesn't reboot itself until I attempt to connect to the hard drive via the Finder, or the AirPort Disk Utility menu. It then goes into the restart loop.
I have just run the 7.1 update for the AEBS, and had this problem before and after the update. My problem seems to be different than most on these forums, but I'm hoping the solution is similar.
MacPro Mac OS X (10.4.9)

How to connect a hard drive on Airport Extreme (second edition)

how to connect a hard drive on Airport Extreme (second edition)? Does it need a special format? It is now fromat on FAT32, but i don't see it ??

The USB port your Mac is high powered. The port on the AirPort Extreme is not.
So, it tends to be borderline as far as its ability to supply sufficient power to a hard drive...even if the hard drive has its own power supply.
Often, users...including me....need to use a powered USB hub when they attach any drive to the USB port on the AirPort Extreme.
You might want to give that a try. Double check to make sure that the drive is formatted in FAT32 as well, since Windows NTFS or exFAT will not work with the AirPort Extreme.
Powering down and restarting the entire network.....modem first, then router, etc.....is something that you would always want to do after any change or addition to a network.

How to deactivate a shared Hard drive on Airport Extreme - keeps sleeping

was curious if anyone one knows how to temporally deactivate a shared Hard drive on Airport Extreme - keeps sleeping every 30mins and have to wait 12 second for the drive to spin up and wait for the beach ball to stop spinning. Getting really aggravating.... Thanks

The external harddrive is NTFS format and someone from apple told me that it would have to be reformatted to be seen by the Extreme -- Needless to say with 33% of the hard drive filled, I do NOT want to reformat.
Unfortunately, HDDs attached to the USB port of the AirPort Extreme, cannot be recognized by the AirPort if formatted in NTFS. If you do not wish to reformat this drive, you will either have to use a different drive or connect this drive to a Windows PC for sharing on the network.
The AirPort can only share drives formatted in HFS+ or FAT32.

Usb hard drive and AirPort Extreme

I have been using an external usb hard drive connected to my Airport Extreme to store music which is then picked up by a Sonos system to play music even when my iMac is switched off - has been working great. However I became aware recently (and I think this pre-dates upgrading my iMac to Mountain Lion) that my external hard drive no longer shows up as a shared drive within Finder. If I go into Airport Utility / Edit / Disks - 'enable file sharing' is checked. Disk Utility doesn't see the drive but I'm not sure that really means anything as a network drive rather than a drive connected directly to the iMac.
Has some recent upgrade disabled network drives on Airport Extreme's (ie assuming we are all now backing up to iCloud so don't need it)?
Thanks

OK, I feel silly on this one.
After looking for issues with the airport and not finding any and needing a file from my backup drive, I had to connect it up to my PC. That's when I found my solution.
The Drive I had connected had stopped responding. That's why the Airport was not showing it and not allowing connections. I had power cycled the drive a few times while testing, just not long enough. I unplugged the drive for 2 minutes, all cables, then reconnected. After about 5 minutes, the Airport was able to confirm the drive and turned the share back on.
Hope that helps.

Can't add hard drive to Airport Extreme

I wanted to add an external hard drive to Airport Extreme and I can't get it to show up in my net work. If I go to the configuration program for Airport Extreme, I can see that the base station has identified that hard drive (a Lacie 750 mb drive). Any suggestions?
Message was edited by: Karlhan

I have the exact same problem with one twist I tried adding an 8gb memory stick instead of a spinning hard drive. Airport utility recognizes it but it does not show up on any of the computers.

ITunes Settings for Media on External Drive via Airport Extreme...

iTunes Settings for Media on External Drive via Airport Extreme base station versus plugging directly into laptop.
My current configuration is that my iTunes Media (700gb) are all stored in an External Drive that's plugged into my Airport Extreme Base Station. This works great for me having wireless access to my iTunes external drive.
Whenever I need to back up that hard drive with Time Machine, I just plug it directly to my laptop...
But how do I let iTunes (or iTunes library) know that this is the same hard drive where all my media is stored when it's plugged directly into the laptop as opposed to trying to access it from my Airport Extreme network?

No there isnt any files call library in the folder i created I am now in the process of copying them back but I guess I will loose all my playlists and playcounts. I do have a Copy of my drive that i made with carbon copy cloner. So maybe it will be best to boot from there, restore and start again.
Chris it was just the media folder. I was following the instructions on the apple support page. Got to point 14 didn't get the warning but did seen to have a brand new itunes, so emptied the trash as they said expecting everything to be fine but it wasnt.

File transfer speed in Shared USB Hard Drive via Airport Extreme

I' am planing to buy one of this, but first I need to know what kind of file transfer speed I can expect when sharing USB drive via Airport Extreme 1000Mbps Ethernet.
Thanks.
Message was edited by: Robert81

most likely 14m/sec but normally 10.5 this is ethernet wired and usb attached. wireless would be about 8M/sec
Wired is good enough I use it for Finder copy frequently.

Incompatibility Issues with connecting USB Hard Drive to Airport Extreme

Over the last few days i have been fiddling around with my new Airport Extreme Base Station N router. I can connect a printer and use the internet through it seamlessly. I can even share two of my hard drives through a USB hub, however, my Maxtor 500 gb One Touch 4 HDD will not connect with my macbook through AEBS. It is only this drive that is not working with AEBS and it is the one i need to be connected and sharing. If i plug my 500gb Maxtor directly into my macbook it works fine, i can read all the files. This drive is formated as Mac OS Extended (journaled).
I am about to give up on this because i have tried everything:
1. Reformatted HDD
2. Downgraded Firmware
3. Searched Forums for advice
4. Reconfigured AEBS in, i think, every way possible
So, these are most of the things ive tried and so far there is no solution in sight. I have one hypothesis: my particular HDD (Maxtor 500gb One Touch 4) is incompatible with AEBS at this time, but it is possible that a future firmware update could fix this.
Does anyone have any advice? I'm lost and disappointed. Please help, thanks.
Message was edited by: benjaminwooda

Chances are pretty good that the power draw of your external drive is just at the "tipping point" for what the USB port on the Extreme can deliver. Powered USB hubs are inexpensive and should help in this situation.

External Hard Drive on Airport Extreme with a PC

I am trying to setup my Seagate FreeAgent external hard drive through my AirPort Extreme with my PC laptop. The AirPort Utility recognizes the disk, and I have enabled file sharing, but I cannot see the drive on either of my PC laptops that are connected to the network. How do I make the drive visable?

With an AirPort Extreme, the PCs will "see" the HFS+ formatted drive on the network as a FAT32 volume, so there is no need to reformat the drive as FAT32, but the normal limitations of FAT32, like maximum file size of 4 GB, slow transfers, etc. will still apply.

How can I access USB drive on AirPort Extreme with iPad

Good day. I recently purchased an AirPort Extreme, and am very pleased. I thought I would take advantage of the ability to store files and videos of my children on my USB drive on the router. Installation was flawless, however, i cannot access the USB drive with my IPad. I have seen several postings about this, am i correct in reading that this is not possible without a 3rd party app? If that is the case, could someone point me in the right direction?

Have you tried this? (And is the Airport new enough that you can call Apple?)
*Manually mounting Mac OS Extended (HFS+) volumes*
*From the Finder's Go menu choose Connect to Server.*
*Enter the AirPort Extreme Base Station's LAN IP address (by default 10.0.1.1).*
*Enter the username and password required to access the AirPort Disk(s).*
*Select the desired AirPort Disk(s) from the available Volumes.*
*Manually mounting FAT16/FAT32 volumes*
*From the Finder's Go menu choose Connect to Server.*
*Enter the AirPort Extreme Base Station's LAN IP address preceded by smb:// (for example, smb://10.0.1.1 )*
*Enter the username and password required to access the AirPort Disk(s). Leave the Workgroup field empty unless you have assigned one in AirPort Utility.*
*Select the desired AirPort Disk from the available CIFS (Common Internet File System) volumes*

Time machine with USB drive on Airport Extreme

For 2+ years I used a USB hard drive shared off my Airport Extreme to host time machine backups. I just switched internet providers solely so that i could go back to using my airport extreme and sharing a backup disk. But time machine no longer shows it as an available drive...and I found this
AirPort base stations: Time Machine hard drive compatibility - Apple Support
which states: Time Machine is not supported with USB hard drives that are connected to an AirPort Express or AirPort Extreme device.
This is a pretty big step backwards as far as I'm concerned.....are there are any ways around it?

There is a way around it: buy the latest type of the Airport Extreme (the tall one). But even that solution isn't considered reliable: http://pondini.org/TM/AEQ2.html

Partition an Advanced Format drive with 4KB sector (for Linux OS only)

I got a brand new WD 1TB drive, model WD10EZEX, I'm upgrading from an old 500 GB drive with Arch running on it, and I'm going to make a fresh Arch install on it.
I suddenly learned about all this Advanced Format issue, with the first units "lying" about physical sector size and all that stuff, which started like 2 years ago and I was not aware of.
I couldn't find a step by step guide to perform the proper formatting for a fresh Linux OS install with 4KB-sector, despite the info is out there scattered in tons of blogs, forums, etc.
I figured out the steps for my simple setup, and I'd like to know if everything is all right. For the ones who already know the steps, can you please go to the bottom of the post, and tell me if the final setup is all right to start the fresh install ?? I reproduce all the steps hoping that this will help other people in the future.
I'll use the whole drive only for an Archlinux install, with one partition for the / and another for /home.
Seems the GPT modern method is the way to go, and the gdisk tool will do the trick. If we are booting from this drive, with GRUB2 in a BIOS system, we must also create a BIOS Boot Partition.
So, with the drive having no partitions at all, and sda being the device name
# gdisk /dev/sda
Command (? for help): p
Disk /dev/sda: 1953525168 sectors, 931.5 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 6527769B-B4BC-408C-A45B-D2DAA4036620
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 2048-sector boundaries
Total free space is 1953525101 sectors (931.5 GiB)
Number Start (sector) End (sector) Size Code Name
we create the 2 MiB BIOS Boot Partition
Command (? for help): n
Partition number (1-128, default 1): 1
First sector (34-1953525134, default = 2048) or {+-}size{KMGTP}: 2048
Last sector (2048-1953525134, default = 1953525134) or {+-}size{KMGTP}: +2M
Current type is 'Linux filesystem'
Hex code or GUID (L to show codes, Enter = 8300): ef02
a 45GB partition to use as /
Command (? for help): n
Partition number (2-128, default 2):
First sector (34-1953525134, default = 6144) or {+-}size{KMGTP}:
Last sector (6144-1953525134, default = 1953525134) or {+-}size{KMGTP}: +45G
Current type is 'Linux filesystem'
Hex code or GUID (L to show codes, Enter = 8300): 8300
Changed type of partition to 'Linux filesystem'
and the rest to use as /home
Command (? for help): n
Partition number (3-128, default 3): 3
First sector (34-1953525134, default = 94377984) or {+-}size{KMGTP}:
Last sector (94377984-1953525134, default = 1953525134) or {+-}size{KMGTP}:
Current type is 'Linux filesystem'
Hex code or GUID (L to show codes, Enter = 8300): 8300
Changed type of partition to 'Linux filesystem'
we can check the setup
Command (? for help): p
Disk /dev/sda: 1953525168 sectors, 931.5 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 6527769B-B4BC-408C-A45B-D2DAA4036620
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 2048-sector boundaries
Total free space is 2014 sectors (1007.0 KiB)
Number Start (sector) End (sector) Size Code Name
1 2048 6143 2.0 MiB EF02 BIOS boot partition
2 6144 94377983 45.0 GiB 8300 Linux filesystem
3 94377984 1953525134 886.5 GiB 8300 Linux filesystem
and everything looks fine, we have the multiples of 8 starting sectors, so we write the changes
Command (? for help): w
Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING PARTITIONS!!
Do you want to proceed? (Y/N): y
OK; writing new GUID partition table (GPT) to /dev/sda.
The operation has completed successfully.
now we need to give the / and /home partitions a format, I choose ext4 and ask for a 4096 block size just in case we have a "lying" unit (not my case but I prefer to write down the most general command)
# mkfs.ext4 -b 4096 /dev/sda2
mke2fs 1.42.6 (21-Sep-2012)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
2949120 inodes, 11796480 blocks
589824 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=4294967296
360 block groups
32768 blocks per group, 32768 fragments per group
8192 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000, 7962624, 11239424
Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done
and the same thing for /dev/sda3 .
Check with gdisk and parted that everything is fine, is this all right to start the install ??
# gdisk -l /dev/sda
GPT fdisk (gdisk) version 0.8.5
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sda: 1953525168 sectors, 931.5 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 6527769B-B4BC-408C-A45B-D2DAA4036620
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 2048-sector boundaries
Total free space is 2014 sectors (1007.0 KiB)
Number Start (sector) End (sector) Size Code Name
1 2048 6143 2.0 MiB EF02 BIOS boot partition
2 6144 94377983 45.0 GiB 8300 Linux filesystem
3 94377984 1953525134 886.5 GiB 8300 Linux filesystem
# parted /dev/sda
GNU Parted 3.1
Using /dev/sda
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) print
Model: ATA WDC WD10EZEX-00R (scsi)
Disk /dev/sda: 1000GB
Sector size (logical/physical): 512B/4096B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 1049kB 3146kB 2097kB BIOS boot partition bios_grub
2 3146kB 48.3GB 48.3GB ext4 Linux filesystem
3 48.3GB 1000GB 952GB ext4 Linux filesystem
Last edited by karamaz0v (2012-12-06 06:39:45)

Your partitions look fine from an Advanced Format point of view. The test is simple: Are all your partitions' start points, as measured in sectors, divisible by 8? Yours are.
karamaz0v wrote:what confused me a bit, was that I saw a lot of setups with the BIOS boot partition, and also a 200 MB EFI one. Having a BIOS system, I think I don't need the EFI one.
Some people do this because they're unclear of their requirements. Others do it because they want to have the option of switching boot modes between BIOS/legacy and EFI. With both types of boot loader installed, you can choose on a boot-by-boot basis which way to start the computer, assuming it supports both boot modes.

Installing 10.6 on a formatted drive with no install DVD

Hi,
I have an intel 2006 core duo iMac which has a formatted drive (Mac OS Extended (Journaled)). I want to instal Snow Leopard on this iMac, the latest version of OS X I can I believe, but I do not have the install DVD.
I have a Snow Leopard DVD which came with my MacBook Pro, but when I tried to use that an error told me that Snow Leopard could not be installed on the iMac. I know it can as I have seen it running.
Is this because I am trying to use the DVD that came with my MacBook Pro? If so, what are the options available to me to get a copy of the OS that I can install from?
Many thanks,
Ian

You cannot use an installer DVD for another model. They are usually incompatible and it's illegal.
You can purchase Snow Leopard by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The price is $19.99 plus tax. You will receive physical media - DVD - by mail.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store.
Depending upon the actual model you have you may be able to install Lion on it. You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Snow Leopard General requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider; fees may apply.
6. Some features require Apple’s MobileMe service; fees and terms apply.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7, or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.

Setting up USB External Drive to Airport Extreme Base Station

I've attached an External Hard Drive to my AEBS. My base computer is connected to the AEBS via Ethernet Cable and can see the external drive under Networked Drive however it shows up twice as Drive Y and Drive Z both showing the exact same capacity.
My desktop computer is running windows vista, and my laptop is also running vista. My Laptop connects to the AEBS wirelessly. The laptop does not see this External Hard Drive. How do I get my laptop to recognize this drive? Shoule my external hard drive display with two different drive letters, or should it only appear as one? I've not had much luck using this feature of the airport extreme and was the basic reason i purchased the AEBS

The USB port on the AirPort Extreme will support drive formats of Mac OS Extended (Journaled) and FAT32. NTFS is not supported, so that might explain some of your difficulties.
What feature did I invoke that automatically established a "third" drive? Where is it established on the physically formatted Mac drive? Does the format of Appleshare just indicate how the partition is accessed?
Not sure about this. When I format a drive as Mac OS or FAT 32, I see a single drive when accessed from the Finder.

Formatting drive with Airport Extreme with Encryption?

Similar Messages

Maybe you are looking for