Forwarding help

I just set up forwarding and a mask with my godaddy account for my iweb site but when I try to log in i get an error message saying:
To view this page, you need to log in to area “idisk.mac.com” on www.karenard.com.
Then it asks for a name and password. I do not have my site private and if you go to karenard.com (without the www) it works. people always type in www though so they won't be able to get to my site! Help! What can I do to fix this. The go daddy support guy said it was fine on their side and it had to do with iweb...??? Thanks

Hi Torevollan and welcome to the Cisco Home Community!
The EPC3925 is handled by the Cisco Small Business Support Community.
For discussions about this product, please go here.
https://supportforums.cisco.com/community/netpro/small-business

Similar Messages

Application And Gaming / Port Forwarding || HELP NEEDED || Can Only Access Via LAN

Hi.
I have just bought a Wireless Router, Model Number: WGKPC354G-UK. With the intention of setting up a small server. This server will run from my PC (directly wired into router), running a game called "Counter Strike" - I had to download a dedicated-server tool for this and i successfuly installed this and followed the tutorial to set it all up..
So I thought i had done it, but I could only access my server with my internal IP 192.168.1.64 (LAN).
I then found out that i needed to "Port-Forward" I followed a tutorial on www.portforward.com - This showed me how to open the ports, and which ones to open.
I did all this and i still encounter the same problem !
So i then opened all my router ports "DNZ" and it still doesnt work !!!
Any help will be greatly aprreciated !
PS. Below Are The Required Ports.
http://portforward.com/english/routers/port_forwarding/Linksys/WAG354G/Counter_Strike.htm

Keep in mind your ISP could be blocking the ports needed. DMZ almost ALWAYS works and if it doesnt, most likely your ISP blocks the ports.
another test is to make sure you can connect to the game server from another CS machine on the inside of your network. If this works, that means your server is up and running properly and its probably your ISP blocking certain ports needed for the CS Server.
You should also check you have the Windows firewall disabled, and any other software firewall on your server disabled.

Attachment to email does not stay attached when email is forwarded - HELP

I recieved an email that had a pdf attachment and when I forwarded the email, the attachment was no longer there?
Is there something I need to do to keep the pdf attachment with the forwarded email - I also have to do this with tiff attachments.
Please help me fix this. Do I need some app that I don't have yet?

Hi. I am sorry you are having issues forwarding emails with an attachment and I can certainly help you from here. Does this happen when you forward any type of attachment or is it just PDF attachments? Are you forwarding this from your Gmail email account? Does the recipient of the email get the email and just not the attachment?
Waiting on your reply
Thanks!

Port Forwarding HELP NEEDED!!!!

I have a HomeHub v2 and I just cannot get the 25565 port open!
I have it opened in the router settings exactly as all the guides say to do it however http://www.yougetsignal.com/tools/open-ports/ still says it's closed!!!!!!
Please help, what am I doing wrong???

As well as the suggestion above, you also need to check that the IP address/Device Name that the Port Forwarding is assigned to is available. You should use ping to check this locally first.
Due to the IP address being dynamic (able to change when the DHCP lease expires), it is sometimes easier to set a static IP address on the device you are forwarding to.
Settings->Advanced->Home Network->Click on Device->Always use this IP address. While you are there, check that this device corresponds to the IP address/hostname that you have Port forwarded to.
For your convenience, Home Network link here:
http://192.168.1.254/hnet_device.lp?be=1&l2=0&l0=2&l1=3

JSP forward *HELP*

Hi,
Im trying to forward a JSP page to another if user password is blank,,
the code is :
errorString rURL = "myURL";
if (Pass.length() == 0){response.sendRedirect(rURL);} but I get the following error:
HTTP Status 500 - Internal Server Error
type Exception report
message Internal Server Error
description The server encountered an internal error (Internal Server Error) that prevented it from fulfilling this request.
exception
org.apache.jasper.JasperException: Cannot forward after response has been committed
     at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:254)
     at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:295)
     at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:241)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDispatcher.java:684)
     at org.apache.catalina.core.ApplicationDispatcher.doForward(ApplicationDispatcher.java:432)
     at org.apache.catalina.core.ApplicationDispatcher.forward(ApplicationDispatcher.java:356)
     at org.apache.jsp.mainController_jsp._jspService(mainController_jsp.java:52)
     at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:137)
Can you please help me..

Try it like this:
if (Pass.length() == 0){
response.sendRedirect(rURL);
return;
} Basically after you redirect/forward from your servlet, you should make sure the execution leaves your servlet/jsp page. Otherwise your page will keep adding to the output, which may result in this sort of error - particularly if it tries to forward/redirect to another page.
if (test){
response.sendRedirect(...);
return;
}or
if (test){
response.sendRedirect(...);
else {
}

Port Mapping / port forwarding - help please...again...

Hi,
I am trying to use port forwarding/port mapping but after numerous failures to access my computer from an Internat connection, I am seeking advice or guidance.
I have a 2011 Apple Time Capsule, and under the Advanced tab on Airport utilities, Port mapping I have chosen +
it then comes up with a box in which I have entered the following:
Service - drop down menu (number of options...but have been advised on other threads to leave as is)
It then has 5 boxes:
Public UDP port(s) - 9080
Public TCP ports(s) - 9080
Private IP adress    - 10.0.1.x
Private UDP Port(s) - 9080
Private TCP Port(s)   -9080
note I have enabled NAT port mapping protocall. My ISP has advised that I cant use port 80 for some reason...but all others should be ok
note also the 10.0.1.x is a static address i have assigned to teh camera.
I have a dns provider, and when I use the URL on my LAN - I can access the camera....but as soon as I tryu to access via the WAN - it is unable to reach the server.
Other points - the TC is in normal mode (i.e. not Bridge)
Does anyone have any idea if I have set port mapping up correctly; any way i can test, any ideas how i can fix this??
I have tried this on a number of forums thus far - but no success to date.
Welcome all and any help!!!

LaPastenague wrote:
Have you reset the camera web page to use 9080?
i have checked again and in teh advances settings of my camera - it asks for HTTP port, HTTPS port, and for Nata Traversal it asks for an alternative HTTP port.   I have entered 9080 against all of these.
The TC is in normal mode ie as a router.. what modem do you have in front of it? Is it in bridge? Does the TC get the public IP or does the modem route the address as well? You will have no success via double NAT.
not sure what brand the modem is - but i can confirm it is set up as a modem only with both the router and wireless functions turned off.
The Modem is not in Bridge mode - neither is my ATC. The ATC gets the public IP address via the adsl modem. so double NAT should not be an issue
When you say you can access the camera using URL on lan, is that using the new port 9080? Please give explicitly what address you use.. (you can hide the full public address) and port.. and AFAIK this should NOT work as the TC would have to handle NAT Loopback which would amaze me if it does. According to all the info around the web the TC has no NAT Loopback and therefore should not be able to handle the address. I need to know therefore the exact address you use
this is actually using the url that my dns provider provides to me as i do not have a static ip address.   albeit this appears temperamental as to when it works sometimes from my LAN. after which it requests user name and password and I can then see the live stream.
one problem I have just noted is that when checking teh DNS setup - it still appears to default to port 80 which my isp has advised i can not use) so i am checking with teh dns provider how i change this.
The good news is port mapping must work on my ATC, as I have just set up my slingbox using their automatic port mapping assistant and it seemed to set up with no issues...i have also just confirmed that the stream can be viewed on the internet.

WRT54GS utorrent port forwarding (HELP PLEASE)

Hey everyone, I bought my WRT54GS router yesterday and cant forward utorrent ports. I have a static IP set up and am trying to use port 32069. I am sure all of my settings are correct in the port forwarding section, nad have tried checking/unchecking "enable". I think i've tried everything so far and it still wont work. If anyone can help me with this, it'd be greatly appriciated.
Message Edited by SinInSpira on 06-28-2007 09:28 PM

if the ports are not getting forwarded , try upgrading / reflashing the router's firmware ..

FritzBox Port Forwarding Help???

Does anyone out there have any experience with port forwarding
and the Fritzbox model 7170 or 7040? I am Having porblems with
an iChat account and it is possible that the culprit is the
Fritz Box.
Thanks in advance

Hi,
I have a FritzBox 7170 that I've used with port forwarding, I'll try to be as specific as possible. Before you do this, you need to assign your computer a static IP address, if you don't have one yet. (See here if you don't know how to do this, scroll a little for the Mac OS X section: http://corz.org/comms/hardware/router/static.ip.address.php)
1. Open a browser page (Safari, Firefox, whatever) and access your FritzBox. Usually with the address fritz.box or with an IP address that you find in the documentation.
2. Make sure you have the "expert settings" on. Go to the menu "Ansicht" and there choose "Experteneinstellungen anzeigen". Confirm this by pressing the button "Übernehmen".
3. Go to the settings menu- "Einstellungen"
4. Click on "internet". You'll see several sub-menus, including "port forwarding" ("Portfreigabe").
5. Click on "new port" ("neue Portfreigabe").
6. Youl'll see a pull-down menu, choose "Other applications" (Andere Anwendungen"). Write your own IP address in the field below.
7. Write "iChat" under "description" (Bezeichnung) and then choose your preferred protocol, add the port number you want to reserve for iChat in "from" and "to", your IP address should have been automatically added and then write port number again under "an Port". Confirm by clicking on "Übernehmen".
That should be it. You probably had tried already, but hadn't seen the options because you hadn't turned on the expert settings option. The same happened to me I hope this helped.
iMac G5 17' Mac OS X (10.4.6)

WRT45G Port Forwarding Help

Ok I just switched to this router yesterday. Before that I had a dlink one. I copyed the ports that I needed to rune Apache Xampp and my Game server called Evolutions. Now I tryed port forwarding with this router but all i get is " User Login - Failed
Access permission is currently denied
Can anyone Help me? I will attatch a screenshot of what I did to port forward.
As you can see i am trying to portforward Neverland which it my game server that I run and Apache to be able to have a site run off my computer.
If anyone can help please do
Thanks in advance,
Cailer

It looks like you have assigned your server a fixed (static) LAN IP address of 192.168.1.101 --- is this correct? If you are not using a fixed LAN IP address in your server, you probably should be, otherwise, from time to time, your server will get a different address from the DHCP server, and your port forwarding won't work.
If you did setup your server with a fixed LAN IP address of 192.168.1.101, then you are probably using an illegal fixed LAN IP address. With Linksys routers, fixed LAN IP addresses must be outside the DHCP server range. (This is different from D-Link routers.)
Rules for using fixed LAN IP addresses on Linksys routers:
With Linksys routers, a fixed (static) LAN IP addresses must be assigned in the device that is using the address. So you need to enter the fixed address in the computer or printer, not in the router.
When using a Linksys router, any fixed LAN IP address must be outside the DHCP server range (typically 192.168.1.100 thru 192.168.1.149), and it cannot end in 0, 1, or 255.
Therefore any fixed LAN IP address would normally need to be in the range of
192.168.1.2 thru 192.168.1.99 or
192.168.1.150 thru 192.168.1.254
assuming you are still using the default DHCP server range.
Also, in the computer, when you set up a static LAN IP address, you would need to set the "Subnet mask" to 255.255.255.0 and the "Default Gateway" to 192.168.1.1
It is also important that no two devices on your network be set to the same static LAN IP address.
Check all of your static LAN IP addresses. If you have violated any of the above rules for static LAN IP addresses, it could be the cause for your problem, and you should fix it before attempting any other router repairs or changes.
Also, are you sure you need to use port 443 ? Port 443 is usually used for "https" communications. Is that what you are using it for?
Message Edited by toomanydonuts on 05-30-200701:56 AM
Message Edited by toomanydonuts on 05-30-200701:57 AM

I need port forwarding help for xbox live. I have a WRT54G router.

I forwarded the ports but it still says I have a moderate NAT. I think I need to get a static IP address on my PC and I know how but what DNS servers do I put in. When I made my static IP the internet didn't work and I figured it was the wrong DNS servers. Do I also have to switch anything in the router settings? Like switch from DHCP to static IP? Any help would be appreciated.
PS. I know nothing about routers and will need to be told where to switch things.
TYTY

in order to open the ports for the x-box , u need to assign a static ip address on the x-box itself and not the pc.....it should be anywhere in between the following range
192.168.1.2 to 192.168.1.99 or
192.168.1.150 to 192.168.1.254
the dns numbers would be the one from the status page on the router ui...to access the router ui , you need to type http://192.168.1.1 .. logon using "admin" password......on the setup page , adjust the mtu settings to 1365.....under "applications and gaming" , open ports 88 and 3074 and give the ip address of the x-box...

Port forwarding help please

Hi All,
I am looking to forward my airport extreme base station to port 57331. No matter what I trying I can't get Playon software working. It is running through parallels since it is a windows only program that allows netflix to be streamed to a driod phone. Can someone please provide a step by step process to port forward? Thank you so much in advance.
Scott

Can someone please provide a step by step process to port forward?
Scott,
The following is the basic steps to configure port mapping/forwarding on the 802.11n AirPort Extreme Base Station (AEBSn):
To setup port mapping on an AEBSn, either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
o AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <leave at the default setting>
o Public UDP Port(s): 57331
o Public TCP Port(s): 57331
o Private IP Address: <enter the reserved DHCP IP address here>
o Private UDP Port(s): 57331
o Private TCP Port(s): 57331
o Click "Continue"

JSP forwarding (Help!)

After forwarding control to another JSP page or servlet using the RequestDispatcher.forward() method, can the response be modified once the forward method returns? For example,
<%
RequestDispatcher rd = request.getRequestDispatcher("/somepath");
rd.forward(request, response);
response.getWriter().println("Some more output");
%>

After forwarding control to another JSP page or
servlet using the RequestDispatcher.forward() method,
can the response be modified once the forward method
returns? For example,
<%
RequestDispatcher rd =
request.getRequestDispatcher("/somepath");
rd.forward(request, response);
response.getWriter().println("Some more output");
%>Give it a try and see. Or see what The API might have to say about it...

WRT320N. Port forwarding help. Xbox and ps3 playing at same time. NAT issues

Hi
I'm trying to have both my xbox and ps3 play with open NAT's for online gaming. I have had success utilizing info from 'portforward.com'. But the solutions will unlock OPEN NAT for either the ps3 or the xbox .. one at a time. Is there a way to get both to be open?
It seems like one main conflict is the success depends on both utilizing port 3074. But I can't have both use it? ( obviously).
I tried port forwarding the xbox per specs off of this forum and that works great.. And DMZ ing the PS3. But like i said before. Most solutions
leave one console with OPEN and one with Moderate.
Is there a solution that allows both NAT OPEN's on both consoles?

First of all XBOX works on a different port number and PS3 works on a different port numbers. Follow the steps below to open the ports on your router for XBOX and PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
This settings are for your XBOX.
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
For PS3 Follow the steps below
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

E3000 port forwarding help

I cannot access the settings for my E3000. The default "admin:admin" for user/pass doest not work with any kind of capitalization, and my understanding is that the other way is to use Cisco Connect ... but I cannot find anywhere to download Cisco Connect. Help?
Solved!
Go to Solution.

If you are unable to login to the setup page of your Router using the default password, then you need to reset your router. ress and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable...Now re-configure your router...

Company Email Forwarding Help

Hi,
our company has our domain bought through 123-reg.co.uk, which has given me an email address of [email protected]
All our emails are forwarded through gmx.co.uk.
I have setup my email account on my iphone as follows:
Name: me
address:[email protected]
username:[email protected]
incoming mail server:pop.gmx.com
outgoing mail server:smtp.gmx.com
i am recieving all my emails to [email protected] with no problems.
when I go to send an email I get the following error message: 'Cannot send mail - The sender address was invalid'.
would anyone have any idea what the problem is?
these seem to be the same settings that I use on my outlook and I did use on my blackberry.

Its possible that GMX do not like you sending out emails with the 'from' address not being one of their addresses. It would appear to some systems that you are faking the response address like spammers do to disguise the sender. Ss GMX is a free service, its pretty likely.
Or a whole host of other reasons I guess.
Have you asked GMX ?
And why not just send the emails direct from your company website hosted facilities ? If you have www.blahblah.co.uk then you should have a mails ever you can use for outgoing mail rather than forwarding everythng to GMX ?

Forwarding help

Similar Messages

Maybe you are looking for