Fp-2000 status LED starts blinking

The status led of my FP-2000 started blinking twice after turning off my module and turning it on again, I already updated the firmware to version 10.4 following the indicated steps. I already tried in safe mode, also reset and format disk , always after configuring the IP the status button starts blinking twice, again.
Thank you for your support

Hi Srael
Try following this document to see if you can solve the problem
http://zone.ni.com/devzone/cda/tut/p/id/4466
Greetings
Julio Mena

Similar Messages

CFP-2110 controller STATUS LED red blinking after powering up

Hi,
Have any one experienced this before: once we powered up the control panel to the instrument, the cFP-2110 controller would just start blinking the RED STATUS signal. I checked the manual on cFP-2110 and it says if the red signal comes off more than 4 times, it is an unrecoverable error. Any recommendation from the board?
Thanks a lot.

Hi,
The default IP is 0.0.0.0. Do you see this same behavior when booting into safe mode? Please see the cFP-21xx User Manual page A-2. You can also contact NI support at www.ni.com/support.
Lynn
National Instruments
Staff Systems Engineer

UCS240 M3 System status LED Amber blinking

Hi Guys
I have a alarm in the UCS240 . The System status LED Amber is blinking, but in the vCenter nothing appears abnormal.
Please see the captures:
-System Event
-System Status
- CPU
- Memory
- Storage
-Temperature
-Platform Alert
TIA
Cristian

Dear Eric
Time :Fri Dec 20 12:55:17 2013
Severity :Warning
Code :F1008
DN :sys/rack-unit-1/board/storage-FLASH-ctlr-1/vd-HV
Probable Cause :equipmentDegraded
Description :Flex Flash Virtual Drive HV Degraded: please check the flash device or the controller
TIA.
Cristian

Cisco AIR -LAP-1142 status led continuosly blinking green

hello all,
I have implemented around 46 access points (AIR-LAP-1142) in a customer site and i can see that the led of some of the access points are continously blinking green and no clients are associated to these access points. I have a WISM which has two controllers in it. I can see the particular aps to be joined in the controller. But my question is that why its not giving me any signal. Please help me as this is very urgent!!.. even if am under the access point the signal is not there. I checked the radio status of the aps and its up. The WLANs are activated from the controller also. Please help mee....!!

continously blinking green
This could mean that the AP hasn't joined the WiSM yet.
Can you console into the AP? If you can, reboot the AP and post the entire power up and bootup process and include the "sh logs".

D400 - system status LED blinking, network LED blinking

Hi - Just recently started experiencing this problem with my D400.
The system status LED is blinking, which according to the user guide means that WHS is either booting or shutting down. The Network LED shows activity.
Problem is that I can't get on the D400 via remote desktop.
Frustrating. Talked with support already, said only option is to send in to depot or find a local resource to troubleshoot or fix. Problem is that we have our music/photos on this thing.
Support also said that if we factory reset data on all drives will be erased.
Looking for help wherever I can get it. Thanks!
Scott

Hi scottdcm, and welcome to the Lenovo User Community!
To get your music/photos off the system before returning it for service, connect the hard drive(s) to another computer with a SATA connection. An external USB/SATA connector or drive enclosure will also do the job.
You can also remove any drives you have added before shipping it for service.
Hope this helps!
I don't work for Lenovo. I'm a crazy volunteer!

FP-1600 Status LED blinks 17 times.

My FieldPoint bank has 9 modules. I previously had a problem with the FP-TB-10 power and ready lights blinking, but that was because one of my dual-channel modules was not seated correctly. Now the status LED is blinking 17 times. The manual says to contact NI about this. The FieldPoint Explorer seems to find all of the modules correctly, though. Anyone know what's up?

Aaron,
I checked the firmware and the FieldPoint Explorer version, and I'm using 3.20 and 3.0, respectively. When I power cycle the FP-1600, the 17 blinks of the status LED go away. Communication works, and all of the devices are found. However, communication does drop out from time to time, and eventually the status LED begins blinking 17 times again.
A possibly related issue is that the FP-AI-V10 dual-channel module that I have plugged into slot 2 of the FP-TB-10 base causes the FP-TB-10 to flash its power and ready LEDs. Re-seating the FP-AI-V10 seems to fix this, although the module is definitely already clicked into place when I see this problem. Upon reseating (or just pressing on it without removing the module), the FieldPoint Explo
rer program finds this module.
I'm tempted to think that this issue with the FP-TB-10 and FP-AI-V10 are unrelated to the FP-1600's status LED blinking 17 times because even with the FP-TB-10 removed from the bank, I still get the flashing LED.
Any ideas? Also, what is a GPF type error?
Thanks,
Jake

NI smart camera 1764 Status LED Blinking

I am using NI smart camera 1764. when i am giving 24 V DC supply to the camera then Power & Status LED is blinking continuously in RED colour. on the other hand pass & fail LED also blinking in RED & GREEN colour alternatively. i am not able to connect camera to my computer through ETHERNET cable & cannot use for my application.
Please suggest me the solution as soon as possible.

Have a look at chapter 6 of this manual:
http://www.ni.com/pdf/manuals/372429b.pdf
Adnan Zafar
Certified LabVIEW Architect
Coleman Technologies

CompactRIO unusual error status LED flashing continuously

Hi,
I have a cRIO 9014 controller with an error i can't solve.
After re-installing LV 8.5 on my laptop MAX could see the controller but with the VISA and NI-RIO error. I wanted to obtain the IP address from the DHCP server (before i used the static IP address without any problems), rebooted the controller and the status LED started flashing continuously every 1 second. (unrecoverable error or corrupted flash memory card)
I rebooted the controller several times with IP reset but LED is still flashing. Also in MAX i can't see the controller anymore so reformatting controller is not possible.
Firewall is off, crossover cable is connected, IP of host is ok but no cRIO in MAX
Found a similar problem on the forum http://forums.ni.com/ni/board/message?board.id=170&message.id=238333&query.id=24781#M238333 but it didn't solve my problem unfortunately.
Thanks for your help!
Greetings from the Netherlands

Hello TrabW,
Thank you for your post on our webforum.
Can you try to start up the controller in safe mode? Is it possible to ping the controller? Please try the default IP address and the one you entered (in case the controller didn't reset the IP). Please let me know the results,
Best regards,
Martijn S
Applications Engineer
NI Netherlands

Sun Fire X2100 Blinking Status LED...

We have 3 new Sun Fire X2100 servers at my current job. Just recently the status LED (orange) started blinking. The logs show fine and running a prtdiag shows everything up and running fine. Is there a way to turn off the blinking LED? I have gone over every piece of information I can find and have found nothing about how to turn this off once it has started blinking.

This may be one of two issues:
- There's a know ILOM/nge driver bug in eariler releases of S10 x86 (pre 6/06).
- There's a know issue with an older firmware rev of the BIOS/LOM where the net management port hangs/drops out and triggers the blinking fault LED. Do you know what BIOS revision you are at?
Most times a mobo swap is NOT the fix. You may be making the problem worse because we have mobos in the supply chain with older firmware revisions.
On the X2100's I usually have my customers try:
- Moving the RAM in different slots
- Updating the BIOS/LOM firmware
- Running the PC-Check diags
... before I send a field tech out to do major surgery.

My 1st gen apple tv displays a black screen,led status light is blinking orange constant. I have tried all the owners manuel tips but it appears to have locked up. Any advise?

my apple tv 1st generation appears to have locked up. it constantly now displays only a black screen.No function reset etc from remote use.The led status is constantly blinking orange. I have tried all the manual tips etc but still blank. Any ideas anyone?
Gary.

Same/similar thing just happened to me....two days ago or so. Ran fine for months since going from wifi (major problems) to ethernet now.
I hadn't been on atv 1 for a few days and had it powered down. Turned it on and it ran thru the startup video/sequence then did the ole sit on a black screen where you can hear the remote responses (say, if i hit left on the remote - the 'option not available' doink noise is made instead of the usual sound you'd get if you were moving to the left on the menu.....not sure if that description makes sense?
The 'exit' or moving out of a menu 'noise' does sound, as does the enter/moving into a menu noise.
This has happened in the past, but more when i had it set up via wi fi.
Thing is this time i left it sit on the black screen while reading the paper, and after about 5 minutes, the menu screen finally showed up. Everything was really sluggish to start - but it was there. But, then, i reset it to see if the sluggishness would go away, and back to the black screen after the startup video.....and then 5 minutes later, it came up.
Not sure what is going on...but did have the blinking orange light for a while during the issue.
Don't think its an age thing as it did this even when i first purchased it....
Once into a video or music it runs fine (though i did notice that every once in a while with the music playing from my itunes, it would have a second of silence mid song like it paused for a second, and then would resume as if nothing happened.....
Any ideas whats shaking with this? Does this sound similar to your issue or am i in a different ball park.

Cisco 1131AG LWAP status led yellow and other leds blinking green

I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
The SSID broadcast is enabled.
On the switch the interface is up and there is traffic going in and out of the LAP.
I tired power reset and factory reset for the APs but the problem remains the same.
Any ideas for what might be the problem ?!!
Regards

Yes the clients are not able to see the SSID broadcasted by the AP.
But these APs were functioning normally before without any changes to the WLC config.
I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

No cisco web is working perfectly.
do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
Autonomous AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
LAP AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards

What does it mean when my FP-2000 Status blinks 8 times

I am using FP-2000 modules for data logging. I have 9 systems working on one network. Yesterday, 4 of the modules stopped communicating. 3 were flashing a status light 8 times, 1 was flashing 2 times. What do these lights mean?

Hello Fridge,
Thank you for contacting National Instruments.
Both 2 and 8 flashes on the status LED indicates a problem with your firmware. Try updating your firmware to fix this problem. To do this in MAX, select your FieldPoint Bank under Remote Systems and click on the Firmware Tab at the bottom of the screen. Then browse to your firmware (it should default you to C:\Program Files\National Instruments\FieldPoint\Firmware\Ethernet\FP-2020, or something similar) and click on Upload.
Let me know if this does not help...
Sean C.
Applications Engineer
National Instruments

MDS 9216 - showing red status LED, not starting up

Hi,
In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
Any ideas, any similar experiences?
Many thanks,

As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
Thanks,
Mike

Scroll/Num Lock and Caps Lock LED's blinking not starting

Hi, I have a problem with my Pavillion dv4-1222nr. It was fine last night and this morning when I turned it on the Scroll/Num Lock and Caps Lock lights started blinking. I turned it off and on several times and still a blank screen and blinking lights also the light that shows the hard drive is running is not on. I can hear the fan from the processor and the dvdr engaging oh, that light is blinking too. I pulled out the battery to see if it would reset but it didn't work. Can anyone please help

Hi, I have a HP Pavillon Dv4 1225 dx. Since a week when I turn it on I hear a noise that seems that it is going to start but it doesn´t. The scroll, num block and caps looks bottom are blinking all time and the screen remains as if it were off, even if I wait for an a half an hour. I tried changing the memories, connecting another monitor, checking the battery but it doesn´t work. I would be great if you could give me an advice about what can I do to solve the problem. Kind regards

Fp-2000 status LED starts blinking

Similar Messages

Maybe you are looking for