FPGA target visible in MAX but not in LabVIEW

Hey!
I recently installed a RIO device. Before installing the hardware, i installed FPGA module & RIO 3.0 as directed. Now i can see the device in measurement & automation explorer, but its not in 'Add targets & devices' list. It says 'No devices found' in existing devices tab. I cant understand the problem. :/
Solved!
Go to Solution.

That's interesting...seems like a similar post to this:
http://forums.ni.com/ni/board/message?board.id=280&message.id=6481
Try to follow the suggestions mentioned in there and post back if you still have issues.
Adnan Zafar
Certified LabVIEW Architect
Coleman Technologies

Similar Messages

Device works fine with MAx but not with Labview visa serial

I have a Monarch rpm sensor hooked up to Monarch tachometer , it gives error while coding in labview and works fine in Max if the sensor doesn't read 0. I have written simple RS-232 programs never had an error but this one is giving errors ..not ablt to fix it..please help
Solved!
Go to Solution.

No device can actually measure a speed of zero. It can only specify that the speed is less than some minimum, which depends on how long you are willing to wait for an answer.
I do not know anything about your instrument, but I would guess that you are getting an error which is the equivalent of "The instrument has waited the maximum permissible amount of time and did not detect any measurable motion." This is the instrument's way of saying that the speed may be zero, or very slow, or something is broken so that it cannot make a measurement but it cannot detect the problem.
Look at the manual for you instrument to see how it responds to the zero speed condition. This error may be normal. If so, you need to capture the particular error code and handle it however you think is appropriate.
Lynn

Camera works in MAX but not in LabVIEW

I've been struggling a lot with getting a DCC3240M camera from Thorlabs working in LabVIEW. The supplied software (Thorcam) works as it should. However, the LabVIEW SDK does not work as it should, it gives an error 155 "the operation is not supported".
Instead of the SDK I tried the DirectShow drivers and now the camera turns up in MAX and works as it should. It also shows up with IMAQdx Enumerate Cameras.vi and in the Vision Acquisition Express vi. BUT when I try to run either IMAQdx Open Camera.vi or the Express-vi it doesn't work. Open Camera gives a DirectShow error code 0x80040275 "No capture hardware is available, or the hardware is not responding." And when i try to select the camera in the express vi, a red icon appears and I can only select "Cancel":
It's really really annoying that the camera evidently works with the provided drivers, but I cannot use it in LabVIEW.
I would be grateful for any ideas of what is wrong. I am running 32-bit LabVIEW on 64-bit Win8.1.

Issue solved!
I thoroughly removed all drivers that came with the camera and then I installed the manufacturers drivers (IDS) instead of Thorlabs drivers. And now it works, the camera still shows up in MAX and doesn't work. But now the provided VIs work. So I'm happy. It only took me a week to figure it out.

Why is my USB camera recognized in MAX but not in LabView?

I am trying to use myRiO to acquire video using a Logitech HD Pro Webcam C920.
I am using LabView 2013 and have the NI-IMAQdx 4.2.0.3.0 software installed on the myRIO.
I have tried a couple sample programs: https://decibel.ni.com/content/docs/DOC-3587 and https://www.youtube.com/watch?v=L7tMeKshd38.
I plugged my Logitech camera into the myRIO USB port. In both cases, LabView failed to recognize my Logitech camera. However, in both cases, it was able to use the integrated Webcam in my laptop to acquire images. When I disabled the integrated camera, it did not find any camera.
Here is a screenshot of the error when I disabled the integrated camera:
However, when I look at the MAX, the Logitech camera appears and is able to acquire images:
David York

yorkdav1 wrote:
I am trying to use myRiO to acquire video using a Logitech HD Pro Webcam C920.
I am using LabView 2013 and have the NI-IMAQdx 4.2.0.3.0 software installed on the myRIO.
I have tried a couple sample programs: https://decibel.ni.com/content/docs/DOC-3587 and https://www.youtube.com/watch?v=L7tMeKshd38.
I plugged my Logitech camera into the myRIO USB port. In both cases, LabView failed to recognize my Logitech camera. However, in both cases, it was able to use the integrated Webcam in my laptop to acquire images. When I disabled the integrated camera, it did not find any camera.
Here is a screenshot of the error when I disabled the integrated camera:
However, when I look at the MAX, the Logitech camera appears and is able to acquire images:
David York
David,
Have you tried deleting your "session in" control & recreate it? I have come across situation a while back where the control did not get refreshed with latest values from Max and it gave me pretty much same errors as what you see (I believe it was due to a small name change of the resource which did not get refreshed in the session control). I say that because you mentioned camera resource getting detected properly with Max & working. Doesn't hurt to give it a try...
-BTC

Why does the counter work in MAX, but not Labview?

Please help, I have been away from Labview for over 3 months, and I am quite rusty....
Last year, I successfully configured NI9401 to measure period (seconds) by counting the rising edges of my sensor signal. Since then, I have aquired a new PC, and loaded all my software into it, including the Labview VI's that successfully worked on the old computer.
I can see the digital signal using MAX and the test panel for the NI9401, so, I know my wiring and my TTL signal is OK, but, when I try to run the attached VI, nothing happens except the error below.. How do I tell this VI to look for the signal on MOD3/CTR0 and channel 14?
Thanks. I am sure it is a small adjustment...this worked fine a few months ago...not sure what is wrong now.
Thanks,
Dave
Solved!
Go to Solution.
Attachments:
continuously measure period buffered_singlechannel_forum_feb_23_2012.vi ‏20 KB

OK, now. Resolved the issue. The vi is fine, but, some shaky wires were identified...worked in MAX but not in the vi. Now that the connections have been tightened up, it works for both. Sorry for the inconvenience.
Dave

TS1363 my ipod classic is visible in windows but not in itunes, this happens on 2 different computers where my iphone and ipod touch work fine which leads me to think something is up with the ipod itself and i cant find any threads to help

my ipod classic is visible in windows but not in itunes, this happens on 2 different computers where my iphone and ipod touch work fine which leads me to think something is up with the ipod itself and i cant find any threads to help.
any thoughts anyone??

Perhaps the reason you haven't had any replies is because there is no such thing as an 8GB iPod Classic.
I suggest that you begin by correctly identifying which iPod you have.
http://support.apple.com/kb/HT1353

I am trying to set up my newly purchased Apple TV but when I enter my network password while setting up, I am not able to enter the Submit button, any idea how to hit the visible submit button that is visible on screen but not responding?

I am trying to set up my newly purchased Apple TV but when I enter my network password while setting up, I am not able to enter the Submit button, any idea how to hit the visible submit button that is visible on screen but not responding?

You need to use the right arrow on the remote to go all the way to the right. The submit button will be highlighted and you can then press select on the remote to proceed.

Serial communication works in hyperterminal but not in LabView

Hello,
I am trying to control an APP Automated Pressure Controller using LabView 6.1 via a serial connection. I am able to control the system with Hyperterminal but not with LabView. I set used the same setup (9600 baud, 1 stop bit, no parity, no flow control, etc) in LabView that worked in hyperterminal.
According the the documentation from the Pressure Controller: "Every character that is sent to the controller is echoed back to your computer so you can check to see everything is working. When a valid command is given, the controller will also send a carriage return (acsii 13) followed by a line feed (ascii 10) to signify the command was executed. Before sending any commands, the program should clear any characters in the input buffer that may be there from previous responses."
In hyperterminal, when I type in a command such as "OA", the Pressure Controller responds (without pressing enter or any other keys) and I can see the "OA" on the screen. As soon as the Controller is done responding, the cursor moves down to the next line (which I assume is caused by the carriage return and line feed) and waits for the next command.
I have tried to use the Serial Communication.vi with no success. Does Hyperterminal add (or Labview omit) a special character or command that I am missing? Do I need to do something special to clear the input buffer in LabView?
Thanks for any help.
Alex

Hello,
Try to run your application in other system (computer),
frequently some PCs configurations are not recognized by LabVIEW serial
routines. I do not know exactly the problem but is not the first time I know
that kind of problem.
Sometimes the problem comes from the serial property called
Termination Character that enables receive buffered data once you have a
Carrier Return or a Line Feed symbol (Hex 0D/0A) character into the buffer. Try
to set it true and assign a 0A Hex Value.
For sending information you need to finish all command
message with an enter symbol concatenating both (Message + Hex 0D0A) using the
special character in the string palette library. This action permits system to
put out buffered data.
Good Look

TS1538 Running Windows XP,Ipod Mini works fine,but Ipod Nano visible in Windows,but not Itunes.Have loaded latest version of ITunes.How do I prceed

Am running Windows XP pro,Ipod Mini works fine,but Ipod Nano is visible in my computer as a mass storage device,but not in Itunes.The settings on the Ipod says Version 1.0.2 Mac.Have tried all the trouble shooting solutions under Itunes help,but no success.Is it a problem with the Ipod or my Windows computer?Please help.Thanks Marcus.

http://support.apple.com/kb/TS1363

PDF images visible in Adobe but not Preview or Mac Mail's Quick Look

I have a PDF that I am inserting an ad into. I copy and paste the ad from one PDF into another. The problem I am having is when I have the final 10-page PDF with the ad inserted in it, you can open the 10-page PDF in adobe and the ad will be visible, but if you open it in Preview or using Mac Mail's Quick Look, the ad isn't there. When I open the original file with the ad in it (that I copied and pasted the ad from) in Quick Look or Preview, the ad appears. I need to know why the ad isn't showing up after it is copy and pasted into a new PDF?
files can be viewed below or at this address:
http://6letters.com/help/
"lanai3_Grand Jewels-001Winning.pdf" is the document I am copying the ad from
"lanai_122211.pdf" is the document I am pasting the ad into. The ad is on page 10. The ad is viewable in Adobe Acrobat but not in Preview or Mac Mail's Quick Look.
I am using Adobe Acrobat Pro 9 (version 9.4.6) to do the copy/paste/save.
I just clicked the above link and the ad doesn't show up online now either. It is supposed to be in the blank space on page 10.
Any help much appreciated!!!!!!

Hi,
Acrobat 9 and older versions paste images as a stamp/comment which (that poorly functional) Preview cannot see, so you need to "flatten" the page if you want to see a pasted picture in Preview.
(Preview, Mail and QuickLook shares the same rendering library)
You can easily flatten one or several pages in a PDF using this free tools: http://abracadabrapdf.net/articles.php?lng=fr&pg=717

PIR visible in MD63 but not showing in MD04

Hi,
I have transferred SOP plan to demand management through mass processing...requirements are visible in md63 but they are not showing in MD04..
Thanks
Kumar

Dear Kumar,
The PIR is maintained for the version GP,which is not active,as suggested either you should maintain
the PIR for this version as active or else for the version 00(SAP standard).
Regards
Mangalraj.S

How come my comments are visible in iweb but not on published site?

I published my site (after many frustrating attempts and publish errors) and had allowed comments. I made a blog entry and published to .mac and found out from a friend that that particular entry didn't have an option to add a comment. I tried to republish many times - I don't know how it happened but the comment option showed up eventually. I had the same thing happen again today so I tried publishing again but this time I tried publishing to a folder. Not sure if this caused the problem but now one comment on the blog disappeared and the rest are only visible in iweb and not on the published site - on the published site there isn't an opportunity to add comments where they used to be. Can I get the comments back on my site?
Thank you for any help.
MacBook Mac OS X (10.4.10)

Oh, rats. Do I need to remove the folder that I published to? I'm not even sure where to find it. I have republished successfully with the comments still in iweb but they don't show up on-line. I'd really like to get them back on if possible.

Device works using max but not with VI

Hi All..
I am able to control a kepco power supply with comminicating by MAX. But with VI (7.0) that has the same command structure it s not possible..Moreover, i dont get any error message either. Could you have a look the VI attached and make ur comments.
thanks
Attachments:
sweeping current.vi ‏79 KB

I have localized where there are something strange happening.
I attach 2 VIs one of which works but not other one. The only difference is that the working one writes data to Writing VI via buffer. When I change buffer to string it doesnt? It doesnt any make any sense to me.. What is wrong?
Attachments:
writing_data_not_works.vi ‏50 KB
writing_data_working.vi ‏47 KB

Text caption visible on slide but not when running project

I am using Captivate v4.
I have one slide of 64 where the text cpation is seen on the slide and runs correctly when using F3 - but when I run the project / F10 the text caption does not appear.
I have copied the slide with this error onto a blank project as i assumed the project might be corrupt - but the same happens on the blank project.
Help please...anyone ?
Noel

Thanks Rod and Rick,
Not sure what was the cause of the problem - but have fixed it now.
After trying many things, including copying the project onto a new blank Captivate project - none of which worked, I did the following and the problem was fixed.
Working on the original project and the slide with the error - I removed the text caption that was not working (for the nth time) and thought I would try one more time to put the text caption back using a different font.....
When I opened the text caption option I noticed there are "two" options for the transparent text caption one above the line and one below, see below;
I selected the transparent option below the line...and it worked OK.
Have to assume that the ones above the line are the most recently used, and I must have been using this one without noticing which one I was selecting - and there was something wrong with the one above the line.
Staring to think I need to upgrade to v5.5 - but not convinced it is the right thing to do.
Thanks again guys,
Noel

GR/IR difference visible in MB5S but not clearing via MR11

Dear gurus,
I am facing abnormal behaviour of the system. System is showing few POs in MB5s but not showing it in MR11 for clearing purposes. Has anyone faced the same situation ?
Regards,
FR

Transaction MB5S is used to analyse the purchase order history and will list all entries where the goods receipts quantity is not equal to the invoice receipts quantity. The report looks at the purchase order
from a logistics viewpoint.
What MB5S does is to look in table EKBE where the PO history is
stored.If there is any balance between the GR/IR , this is shown
in the report. Sometimes there is confusion in the interpertation of the results of
RM07MSAL. The aim of this program is to show how the GR is effectively valuated
if the existing invoices are taken into account, independently from how the GR itself was valuated (or not valuated).
MB5S is not the appropriate functionality for analysis of the clearing account.
Transaction MR11 will only pick up variances in quantity, not in values.
The aim of MR11 is to clear the GR/IR account, not the quantities.
However, an open item on the GR/IR account can only exist, if the
quantities are different (for normal POs with valuated GR).
MR11 posts like an debit/credit note with value 0 and the open quantity.
This clears the GR/IR account, and the quantities are cleared as well,
but only as a by-product of this mechanism.
POs with non valuated GR never have open items on GR/IR account,
because neither GR nor IR post to the GR/IR account.
For additional information about the MR11 transaction please check
the SAP note 10757 FAQ: MR11, clear GR/IR clearing account.

FPGA target visible in MAX but not in LabVIEW

Similar Messages

Maybe you are looking for