Fragmentation problem with Wlan Controler 4402 due to LWAPP header overhead
Hello there,
I have following situation.
network---wlan controller4402----FW1---MPLS---FW2---Access points----networks
I can see very big amount of fragmented packets coming to FW2 and getting dropped in one moment. After those packets get dropped, access points get disconnected
I wonder, is there any documentation, or maybe some of you guys can give me some tip/trick how to set up WLC4402 to use TCP MSS, PMTU or any other settings that can help that IP Datagrams between 4402 and access points don't go over 1300B
Thanks a lot for any help
Regards
Milos
Hello,
Thanks for your response.
I'm a bit confused watching this document you gave me. I don't know which part of it can be related to prevention of IP Fragments between controller and AP-s.
Problem is that controller is located on one side of the network, and we have FW (non cisco), MPLS network, other FW and then APs
other FW across MPLS receive a lot of fragments, which of course should be defragmented for session inspection, so this leads to large CPU utilization and fragment drops.
If we can instruct controller to set MSS bits or to be involved in PMTU, then we could try to prevent end hosts to ever create large TCP/UDP segments/datagrams to be sent via LWAPP tunnel
Thanks for any advice
Cheers
Milos
Similar Messages
-
I am able to make it to the site for about 2 seconds and then I am quickly logged off and the statement, "There is a problem with your authentication, possibly due to inactivity. For your safety, you have been logged out and must sign in again to continue."
I don't have a clue as to the problem but since this is impacting my participation in these classes and ultimately could have a negative impact on my grade, I am more than a little concerned!Have you allowed this site to set cookies?
-
Problem with Table control lines
Hi Friends,
This is the problem with table control lines:
I have screen with table control and I would like change the table control lines dynamicaly.
Exp:
In my PBO the Internal table which I am using to loop the TC is havig 7 records and its displayed with 7 records, now I have added one more record into my ITAB and now ITAB is having 8 records, when I am looping this ITAB with TC its taking the TC lines 7 only.
here is the code:
Initial values in gt_scr400 = 8
Initial values in tc_scr400 = 8
Now added one more recor into gt_scr400 , now gt_scr400 = 9.
LOOP AT gt_scr400
INTO wa_scr400
WITH CONTROL tc_scr400
CURSOR tc_scr400-current_line.
ENDLOOP.
I have used this logic :
DESCRIBE TABLE gt_scr400 LINES g_rec_300 .
tc_scr300-lines = g_rec_300.
but its not modifying the lines in my table control.
How to change the TC lines based on ITAB total records.
Thanks,
Sridharthere is a field in TableViewName-xxx
don't remember the exact field name for (total no of records)
you can check it in debug. when you add records in Internal table, u need to modify this field which is set at the first time when table control is populated. -
Who else has a problem with parental controls enabled not being able to run Firefox on the Mac?
Who else has a problem with parental controls enabled not being able to run Firefox on the Mac? (Any solutions?) (BTW. Chrome doesn't work either)
Although FF4 is so nice I'm almost ready to ditch iGoogle!
Please fix what appears to be an RSS/iGoogle issue with FF4...
Gmail is fine, but titles dont show in most RSS feed gadgets and no stories, strangely, apart from this one:
http://www.google.com.au/ig/directory?hl=en&url=www.google.com/ig/modules/builtin_news_technology.xml
Which if you enter the last part of the url reports that
"<Content type="html">
This is a builtin module, so the UserPrefs and Content are ignored."
Any ideas? -
Keyboard problem with T410 - Control Key
I have a problem with the control keys on the keyboard of T410.
I swapped my X200 keyboard over to T410 to check if it is software or hardware issues. With the X200 keyboard, the 'Ctrl' key is not working. With the T410 keyboard, 'e', 'd', 'c' and 'Ctrl' keys are not working.Welcome to the forum!
I believe that X200 and T410 keyboards are mapped differently in BIOS.
Can you find another T410/T510 keyboard to test with?
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you. -
URGENT ! JDEV 10.1.2 Problem with data control generated from session bean
I got a problem with data control generated from session bean which return a collection of data transfer object.
The dto's seem to be correct. The session bean load correctly the data into and the object's are plenty of data. Using the console to display the dto content is ok.
When generating a data control from this session bean and associate the dto included in the collection only the first object level and one-to-one dto object are correctly setted in the data control. Object that represent collection into the dto (one-to-many foreign key) are setted as collection with an iterator but the structure of the object is not setted. I don't know how to associate this second level of collection with the dto bean class to obtain the attributes definition.
I created a case with hr schema like the hrApp demo application in the tutorial with departments and employees table. I got the same problem.
Is it a bug ?
It exists a workaround to force the data control to understand the collection data structure ?
Help is welcome ! this is urgent !!!we found the problem by assigning the child dto bean class to the node representing the iterator in the xml file corresponding to the master dto.
-
I am experiencing on going problems with my i phone 4 due to me sharing an i tunes account with my daughter. I have been told by apple to cancel my existing (shared) i tunes account and open a new one for my use only. How do I do this? I cant find any links in i tunes to do this. mountfield
No, it's done on the computer, it's just done on the web and not through iTunes. I guess you could do it on the iPhone, but it would be easier to do on the computer.
Just go to the site linked above, then click on the big blue button and fill out the neccessary information. -
Problem with wlan sticks module, not able to write to disk any more
Hello everybody,
when I booted my PC today, a strange and some sort of severe problem occurred concerning my wlan stick(s) that I think, I'm not able to solve without your help. I searched for a solution but it didn't seem that somebody else has had a similar problem before.
Here is the description:
I have two wlan sticks (but I do not use both of them nor are they both plugged in at the same time), and both happen to malfunction since today. My "main" stick (used most of the time) is a BigTec Wireless 11N Adapter with a Realtek chipset. My second one (only used to solve problems with the other stick) is a Fritz! WLAN USB Stick (to be used with ndiswrapper).
After bootup, which makes no problems at all, my "main" wlan stick is not able to connect to the network. When I run wicd-curses (I use wicd as network manager), the virtual terminal freezes (when I use urxvt under openbox to run wicd-curses, only the window freezes). After one minute, a message appears that says something about a dbus problem but I am not able to read it because of the screen clears. Then I'm able to use the terminal again, but (and this is the very, very strange about this) when I run any program that tries to write on my disk it stucks, so I can't cancel it with ctrl-c nor can I kill the process. Wicd-curses, ifconfig or iwconfig also crash after entering the command and show the same behavior. At this point, my wlan stick does not show any sign of being plugged in (normally it blinks...).
My second stick makes the computer crash: After a few moments a stacktrace is shown (like when a kernel panic occurs), saying something about "stack being overrun". But I can't find the message in the log files so it is difficult to post it.
When I tried to figure out a solution, I saw in pacman.log, that yesterday udev and hwdetect were updated... But also downgrading all the packages that were updated yesterday did not solve the problem!
I'll post now the last lines of a few logs here (but nothing concerning the ndiswrapper stick, else it would be too disturbing), I hope they help you at helping me!
everything.log
Jan 23 15:25:26 localhost dhcpcd[835]: dhcpcd not running
Jan 23 15:25:27 localhost kernel: [ 21.415035] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
Jan 23 15:25:27 localhost kernel: [ 22.063785] r8712u: 1 RCR=0x153f00e
Jan 23 15:25:27 localhost kernel: [ 22.064534] r8712u: 2 RCR=0x553f00e
Jan 23 15:25:27 localhost kernel: [ 22.170765] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jan 23 15:25:27 localhost dhcpcd[847]: dhcpcd not running
Jan 23 15:25:28 localhost kernel: [ 22.410354] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
Jan 23 15:25:28 localhost kernel: [ 22.463386] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
Jan 23 15:25:28 localhost kernel: [ 22.463902] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 23 15:25:28 localhost dhcpcd[854]: dhcpcd not running
Jan 23 15:25:28 localhost kernel: [ 22.735037] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
Jan 23 15:25:29 localhost kernel: [ 23.383789] r8712u: 1 RCR=0x153f00e
Jan 23 15:25:29 localhost kernel: [ 23.384535] r8712u: 2 RCR=0x553f00e
Jan 23 15:25:29 localhost kernel: [ 23.490763] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jan 23 15:26:11 localhost dhcpcd[1382]: dhcpcd not running
Jan 23 15:26:12 localhost kernel: [ 66.495307] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin" # then I hard reset because of the freeze
errors.log
Jan 23 15:00:01 localhost /USR/SBIN/CROND[5597]: (CRON) EXEC FAILED (/usr/sbin/sendmail): No such file or directory
Jan 23 15:20:01 localhost /USR/SBIN/CROND[6215]: (CRON) EXEC FAILED (/usr/sbin/sendmail): No such file or directory
Jan 23 15:25:26 localhost dhcpcd[835]: dhcpcd not running
Jan 23 15:25:27 localhost dhcpcd[847]: dhcpcd not running
Jan 23 15:25:28 localhost dhcpcd[854]: dhcpcd not running
Jan 23 15:26:11 localhost dhcpcd[1382]: dhcpcd not running # then I hard reset because of the freeze
daemon.log
Jan 23 15:25:15 localhost [ 0.864888] udevd[48]: starting version 175
Jan 23 15:25:15 localhost [ 4.116488] udevd[235]: starting version 178
Jan 23 15:25:26 localhost dhcpcd[835]: dhcpcd not running
Jan 23 15:25:27 localhost dhcpcd[847]: dhcpcd not running
Jan 23 15:25:28 localhost dhcpcd[854]: dhcpcd not running
Jan 23 15:26:11 localhost dhcpcd[1382]: dhcpcd not running # then I hard reset because of the freeze
I hope you can help me and thank you for trying
hoeffl
P.S.: Excuse all the mistakes I made because of being new here, please!This seems to be a problem with r8712u on all 3.2.x and 3.3-rc kernels on all distros. I've had it for weeks on Gentoo, Arch, and several other distros.
If you are running a 3.2.x kernel, this is almost definitely the problem. All 3.1 kernels don't do this.
I posted a temporary work-around on the Arch bugzilla, and Larry Finger (kernel dev with wireless) is currently working on it (a patch).
In the meantime, If you compile your own kernels, you can get 3.2.x's to work normally- see my comment here for more details. https://bugs.archlinux.org/task/27996
Top of page doesn't say r8712u, but it's the same problem, and after the first 2-3 comments it deals with r8712u specifically.
There is also info on the Gentoo forum 3.2 kernel quirks thread, towards the bottom of Page 1: http://forums.gentoo.org/viewtopic-t-901702.html
Last edited by wrc1944 (2012-02-03 07:45:32) -
Problem with custom control and focus
I've a problem with the focus in a custom control that contains a TextField and some custom nodes.
If i create a form with some of these custom controls i'm not able to navigate through these fields by using the TAB key.
I've implemented a KeyEvent listener on the custom control and was able to grab the focus and forward it to the embedded TextField by calling requestFocus() on the TextField but the problem is that the TextField won't get rid of the focus anymore. Means if i press TAB the first embedded TextField will get the focus, after pressing TAB again the embedded TextField in the next custom control will get the focus AND the former focused TextField still got the focus!?
So i'm not able to remove the focus from an embeded TextField.
Any idea how to do this ?Here you go, it contains the control, skin and behavior of the custom control, the css file and a test file that shows the problem...
control:
import javafx.scene.control.Control;
import javafx.scene.control.TextField;
public class TestInput extends Control {
private static final String DEFAULT_STYLE_CLASS = "test-input";
private TextField textField;
private int id;
public TestInput(final int ID) {
super();
id = ID;
textField = new TextField();
init();
private void init() {
getStyleClass().add(DEFAULT_STYLE_CLASS);
public TextField getTextField() {
return textField;
@Override protected String getUserAgentStylesheet() {
return getClass().getResource("testinput.css").toExternalForm();
@Override public String toString() {
return "TestInput" + id + ": " + super.toString();
}skin:
import com.sun.javafx.scene.control.skin.SkinBase;
import javafx.beans.value.ChangeListener;
import javafx.beans.value.ObservableValue;
import javafx.event.EventHandler;
import javafx.scene.control.TextField;
import javafx.scene.input.KeyCode;
import javafx.scene.input.KeyEvent;
public class TestInputSkin extends SkinBase<TestInput, TestInputBehavior> {
private TestInput control;
private TextField textField;
private boolean initialized;
public TestInputSkin(final TestInput CONTROL) {
super(CONTROL, new TestInputBehavior(CONTROL));
control = CONTROL;
textField = control.getTextField();
initialized = false;
init();
private void init() {
initialized = true;
paint();
public final void paint() {
if (!initialized) {
init();
getChildren().clear();
getChildren().addAll(textField);
@Override public final TestInput getSkinnable() {
return control;
@Override public final void dispose() {
control = null;
}behavior:
import com.sun.javafx.scene.control.behavior.BehaviorBase;
import javafx.beans.value.ChangeListener;
import javafx.beans.value.ObservableValue;
import javafx.event.EventHandler;
import javafx.scene.input.KeyCode;
import javafx.scene.input.KeyEvent;
public class TestInputBehavior extends BehaviorBase<TestInput> {
private TestInput control;
public TestInputBehavior(final TestInput CONTROL) {
super(CONTROL);
control = CONTROL;
control.getTextField().addEventFilter(KeyEvent.KEY_PRESSED, new EventHandler<KeyEvent>() {
@Override public void handle(final KeyEvent EVENT) {
if (KeyEvent.KEY_PRESSED.equals(EVENT.getEventType())) {
keyPressed(EVENT);
control.focusedProperty().addListener(new ChangeListener<Boolean>() {
@Override public void changed(ObservableValue<? extends Boolean> ov, Boolean wasFocused, Boolean isFocused) {
if (isFocused) { isFocused(); } else { lostFocus(); }
public void isFocused() {
System.out.println(control.toString() + " got focus");
control.getTextField().requestFocus();
public void lostFocus() {
System.out.println(control.toString() + " lost focus");
public void keyPressed(KeyEvent EVENT) {
if (KeyCode.TAB.equals(EVENT.getCode())) {
control.getScene().getFocusOwner().requestFocus();
}the css file:
.test-input {
-fx-skin: "TestInputSkin";
}and finally the test app:
import javafx.application.Application;
import javafx.scene.Scene;
import javafx.scene.control.TextField;
import javafx.scene.layout.GridPane;
import javafx.stage.Stage;
public class Test extends Application {
TestInput input1;
TestInput input2;
TestInput input3;
TextField input4;
TextField input5;
TextField input6;
Scene scene;
@Override public void start(final Stage STAGE) {
setupStage(STAGE, setupScene());
private Scene setupScene() {
input1 = new TestInput(1);
input2 = new TestInput(2);
input3 = new TestInput(3);
input4 = new TextField();
input5 = new TextField();
input6 = new TextField();
GridPane pane = new GridPane();
pane.add(input1, 1, 1);
pane.add(input2, 1, 2);
pane.add(input3, 1, 3);
pane.add(input4, 2, 1);
pane.add(input5, 2, 2);
pane.add(input6, 2, 3);
scene = new Scene(pane);
return scene;
private void setupStage(final Stage STAGE, final Scene SCENE) {
STAGE.setTitle("Test");
STAGE.setScene(SCENE);
STAGE.show();
public static void main(String[] args) {
launch(args);
The test app shows three custom controls on the left column and three standard textfields on the right column. If you press TAB you will see what i mean... -
Problems with remote control and user accounts - error 1759?
We're running:
-XP Pro SP2 clients with Zen SP1 IR3a agent, 4.91 SP2 Netware client.
-We are NOT running Middle Tier.
-Novell servers are running Netware 6.5 SP7, E-directory 8.7.3.10b or 8.8.
-Zen server is also SP1 IR3a.
We have no problem using remote control on workstation objects. We are having intermittent issues with remote controlling user objects. When the issue occurs, we receive the following error, "Error 1759: The selected user is not logged in on any workstations" even though the user is in fact logged in. After some more research, it appears that the "networkAddress" attribute of the user object is blank so we feel that this is the root cause. My question is what would cause the networkAddress attribute to randomly not update? For instance we had a user (verified his login) who we could not remote via the user object (workstation object worked). We checked his networkAddress attribute and found that it was empty. User rebooted and logged in again and his networkAddress attribute populated, and then we could remote control him via the user object. Now this isn't always the case after a reboot. There doesn't appear to be any pattern to when the networkAddress attribute does or does not update. In fact, this particular user has a laptop so he boots it up fresh every morning yet he was not showing a network address when he logged in initially today.
We've followed the troubleshooting steps in Novell Documentation without any success. Is there anything else that we might be missing, especially with respect to getting the networkAddress attribute to update? We ran a DSreport on that attribute and found about 500 out of a total of 1500 users had no networkAddress. Some of those are sure to be legitimate but that number is much too high for the number of people that should be in the office.
I've read some older threads on the subject but none of them really provide a firm solution. Also most of the older threads reference Middle Tier which we are not using.
Thanks in advance.> 4.91 SP2 Netware client.
You could try this TID:
"A user will no longer have an entry in their "Network Address" attribute
even though they are logged into the eDirectory Tree."
http://www.novell.com/support/viewCo...1262&sliceId=1
"Resolution"
"This was fixed in the 4.91 SP3 client. NWFS.SYS was modified so that it
will check the monitor connection on a reconnect and if it is not connected
close the connection and try and get a new monitor connection to the tree.
Prior to the 4.91 SP3 client, the solution is to have the user login again
so that it issues the NDS Finish Login request again that will populate
Network Address again."
Regards
Rolf Lidvall
Swedish Radio (Ltd) -
Problem with remote control and Windows 7 - HP Pavilion 6301eu
I installed Windows 7 32-bit and my remote control does not work. I have tried all possible drivers and still nothing ... Photo driver attached. Does anyone have a link to the current drivers for the remote control and Windows 7? thank you
Hi John:
Thanks but, I had already done this. I was having THAT problem with Encore (could not even initialize before tanking) when I first installed it and that's when I updated the Roxio engine. I don't know what else there is to update or correct at this point.
There was one thing that occurred to me: When I was using XP, I had to disable Open GL in order to get Encore to stabilize. I've heard one recommendation for Encore that one must disable graphics acceleration. I would like try that here except I can't figure out how to do that in Windows 7.
I've been Googling "Windows 7 Disable Graphics Accel" and have come up with nothing useful.
Thanks for your help though and if you have any other ideas, I'm all ears.
Mark -
Problem with 'Edit Locally' command -- Due to IISProxy?
Hi,
We have a problem with 'Edit Locally' command since we are using Windows Authentication. Our architecture is:
SAP EP 6.0 SP2 Patch 28 (Solaris)
IIS Proxy (Windows 2003)
The situation is:
If we access to SAP Portal using old url (directly to Solaris) using form-based authentication we do not have any problem with 'edit locally' command.
However, if we access to SAP Portal using IISProxy and Windows Authentication we get an 'Operation failed' error message.
Java plug-in console shows the following message:
cargar: clase com/sapportals/wcm/app/docapplet/DocApplet.class no encontrada.
java.lang.ClassNotFoundException: com.sapportals.wcm.app.docapplet.DocApplet.class
at sun.applet.AppletClassLoader.findClass(Unknown Source)
at java.lang.ClassLoader.loadClass(Unknown Source)
at sun.applet.AppletClassLoader.loadClass(Unknown Source)
at java.lang.ClassLoader.loadClass(Unknown Source)
at sun.applet.AppletClassLoader.loadCode(Unknown Source)
at sun.applet.AppletPanel.createApplet(Unknown Source)
at sun.plugin.AppletViewer.createApplet(Unknown Source)
at sun.applet.AppletPanel.runLoader(Unknown Source)
at sun.applet.AppletPanel.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Caused by: java.io.IOException: open HTTP connection failed.
at sun.applet.AppletClassLoader.getBytes(Unknown Source)
at sun.applet.AppletClassLoader.access$100(Unknown Source)
at sun.applet.AppletClassLoader$1.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
... 10 more
Where is the problem? Is due to authentication method? SAP Portal or IISProxy configuration?
Thanks,Thanks for your comment,
Now, we have tested with version 1.5.0_01 plugin version but the result is the same: 'Operation failed'
This is a very important topic to solve before installing Windows Authentication in a productive environment.
Has anybody any solution?
Damiá -
Problem with reading PNG metadata due to unicode strings
Being new to the XMP SDK I have problems trying to dump the XMP data from a .png file because the data contains UTF-8 data.
I have searched the forum for answers, but the answers I found do not help.
The answer I found was to replace std::string with std::wstring. but that causes problems with the compile - btw, I am using MSVC 2010 C++ Express
and XMP SDK-CC201306
Changing the std:: line to:
#define TXMP_STRING_TYPE std::wstring
and all string definitions in my code to wstring, gives me a bunch of compile errors, such as:
f:\pkg\c++\xmp-toolkit-sdk-cc201306\public\include\client-glue/TXMPMeta.incl_cpp(74): error C2664: 'std::basic_string<_Elem,_Traits,_Ax> &std::basic_string<_Elem,_Traits,_Ax>::assign(const _Elem *,unsigned int)' : cannot convert parameter 1 from 'XMP_StringPtr' to 'const wchar_t *'
1> with
1> [
1> _Elem=wchar_t,
1> _Traits=std::char_traits<wchar_t>,
1> _Ax=std::allocator<wchar_t>
1> ]
1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast
1> f:\pkg\c++\xmp-toolkit-sdk-cc201306\public\include\client-glue/TXMPMeta.incl_cpp(72) : while compiling class template member function 'void TXMPMeta<tStringObj>::SetClientString(void *,XMP_StringPtr,XMP_StringLen)'
1> with
1> [
1> tStringObj=std::wstring
1> ]
1> f:\pkg\c++\XMP-Toolkit-SDK-cc201306\public\include\XMP.incl_cpp(55) : see reference to class template instantiation 'TXMPMeta<tStringObj>' being compiled
1> with
1> [
1> tStringObj=std::wstring
1> ]
Any help or pointers will be most welcome.
TIA,
DayWalkerOK, I now understand the point you were driving at.
To check out this idea, I have modified the code in the routine which dumps the output from the callback to a file as follows:
(Though if you were to dump the file using the std:: stream - .i.e. using the utility as supplied, you should see the same problem - it is not at all dependent on my using the wxWidgets toolkit)
XMP_Status DumpXMPToFile(void * WXUNUSED(refCon), XMP_StringPtr buffer, XMP_StringLen bufferSize )
XMP_Status status = 0;
wxString wsT;
try
wxString wsText( buffer, wxConvUTF8 );
if( g_wfDumpFile.IsOpened() )
wsT.Printf( _T("<%s> size(%d)"), wsText, bufferSize );
g_wfDumpFile.SeekEnd();
g_wfDumpFile.Write( wsT, wsT.Length() );
else
return -1;
catch(XMP_Error & e)
The output for the one line in question:
<Iptc4xmpCore:CiAdrExtadr> size(24)< = "> size(4)<Leo-Saurer-Straße> size(15)<> size(1)<C3> size(2)<> size(1)<9F> size(2)<>> size(1)<e> size(1)<"> size(1)<
> size(1)< > size(3)< > size(3)< > size(3)
The hex contents of the buffer I get in the callback is
0x003908D0 4c 65 6f 2d 53 61 75 72 65 72 2d 53 74 72 61 c3 9f 65 00 cd cd cd cd Leo-Saurer-Straße.ÍÍÍÍ
0x003908E7 cd cd cd cd cd cd cd cd cd fd fd fd fd ab ab ab ab ab ab ab ab ee fe ÍÍÍÍÍÍÍÍÍýýýý««««««««îþ
As you can see, my conversion routines takes all the buffer contains and converts it to the appropriate UTF-8 string, even though the count passed to me is short and represents only the count up to the first non-ASCII character and all of the subsequent strings - interpreted as hex values by the caller of the call back would not give me the correct characters, athough they are passed to me for display.
The two fragments of one byte length are the ones I could not find in the actual output.
The call stack at that point:
>
wxMeta.exe!DumpXMPToFile(void * __formal, const char * buffer, unsigned long bufferSize) Line 110
C++
wxMeta.exe!TextOutputProcWrapper(void * refCon, const char * buffer, unsigned long bufferSize) Line 60 + 0x18 bytes
C++
wxMeta.exe!DumpClearString(const std::basic_string<char,std::char_traits<char>,std::allocator<char> > & value, long (void *, const char *, unsigned long)* outProc, void * refCon) Line 409 + 0x1c bytes
C++
wxMeta.exe!DumpPropertyTree(const XMP_Node * currNode, int indent, unsigned int itemIndex, long (void *, const char *, unsigned long)* outProc, void * refCon) Line 161 + 0x14 bytes
C++
wxMeta.exe!DumpPropertyTree(const XMP_Node * currNode, int indent, unsigned int itemIndex, long (void *, const char *, unsigned long)* outProc, void * refCon) Line 222 + 0x1f bytes
C++
wxMeta.exe!XMPMeta::DumpObject(long (void *, const char *, unsigned long)* outProc, void * refCon) Line 1100 + 0x23 bytes
C++
wxMeta.exe!WXMPMeta_DumpObject_1(__XMPMeta__ * xmpObjRef, long (void *, const char *, unsigned long)* outProc, void * refCon, WXMP_Result * wResult) Line 968
C++
wxMeta.exe!TXMPMeta<std::basic_string<char,std::char_traits<char>,std::allocator<char> > >::DumpObject(long (void *, const char *, unsigned long)* outProc, void * refCon) Line 833 + 0x21 bytes
C++
wxMeta.exe!MyFrame::DisplayMetaData(wxString & wsrFilePathAndName) Line 484
C++
Hoping this will help resolve the issue :-) -
Problem with kerio-control-vpnclient
Hi everyone
i connect to internet with kerio-control-vpnclient
the problem is some site filter by goverment like facebook and when connect with my VPN,
all site load but the facebook and youtube and so on not load
i guess the problem is my DNS
how i enter custom DNS to kerio-control-vpnclient?
Tnks allthere is a field in TableViewName-xxx
don't remember the exact field name for (total no of records)
you can check it in debug. when you add records in Internal table, u need to modify this field which is set at the first time when table control is populated. -
Hi @all
OS Windows Server 2008 (Standard)
DB 11.1.0.7.0
I try to configure DB Control manually with
D:\ORACLE\product\11.1.0\db_1\BIN>emca -config dbcontrol db -repos create
result is
15.09.2009 13:19:14 oracle.sysman.emcp.EMConfig perform
INFO: Dieser Vorgang wird in D:\ORACLE\cfgtoollogs\emca\SAXMBS\emca_2009_09_15_1
3_15_52.log protokolliert.
15.09.2009 13:19:15 oracle.sysman.emcp.util.FileUtil backupFile
WARNUNG: Datei D:\ORACLE\product\11.1.0\db_1\sysman\config\emd.properties konnte
nicht gesichert werden
15.09.2009 13:19:15 oracle.sysman.emcp.util.FileUtil backupFile
WARNUNG: Datei D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties.emca
konnte nicht gesichert werden
15.09.2009 13:19:15 oracle.sysman.emcp.util.FileUtil backupFile
WARNUNG: Datei D:\ORACLE\product\11.1.0\db_1\sysman\emd\targets.xml konnte nicht
gesichert werden
15.09.2009 13:19:15 oracle.sysman.emcp.util.DBControlUtil stopOMS
INFO: Database Control wird gestoppt (dies kann etwas lõnger dauern) ...
15.09.2009 13:19:15 oracle.sysman.emcp.EMReposConfig createRepository
INFO: Das EM-Repository wird erstellt (dies kann etwas lõnger dauern)...
15.09.2009 13:24:22 oracle.sysman.emcp.EMReposConfig invoke
INFO: Repository erfolgreich erstellt
15.09.2009 13:24:23 oracle.sysman.emcp.EMReposConfig uploadConfigDataToRepositor
y
INFO: Konfigurationsdaten werden in das EM-Repository hochgeladen (dies kann etw
as lõnger dauern) ...
15.09.2009 13:25:02 oracle.sysman.emcp.EMReposConfig invoke
INFO: Konfigurationsdaten wurden erfolgreich hochgeladen
15.09.2009 13:25:02 oracle.sysman.emcp.EMConfig perform
SCHWERWIEGEND: Fehler beim Aktualisieren von D:\ORACLE\product\11.1.0\db_1\sysma
n\config\emoms.properties
Weitere Einzelheiten finden Sie in der Log-Datei in D:\ORACLE\cfgtoollogs\emca\S
AXMBS\emca_2009_09_15_13_15_52.log.
Die Konfiguration konnte nicht abgeschlossen werden. Weitere Einzelheiten finden
Sie in der Log-Datei in D:\ORACLE\cfgtoollogs\emca\SAXMBS\emca_2009_09_15_13_15
_52.log.
snippet of the log
at oracle.sysman.emcp.EMConfigAssistant.main(EMConfigAssistant.java:468)
Caused by: java.io.FileNotFoundException: D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties (Zugriff verweigert)
at java.io.FileOutputStream.open(Native Method)
at java.io.FileOutputStream.<init>(FileOutputStream.java:179)
at java.io.FileOutputStream.<init>(FileOutputStream.java:131)
at oracle.sysman.emcp.util.FileUtil._copyFile(FileUtil.java:257)
... 11 more
15.09.2009 13:25:02 oracle.sysman.emcp.EMDBCConfig updateEmomsProps
KONFIG: Datei D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties.emca wird in D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties kopiert
15.09.2009 13:25:02 oracle.sysman.emcp.EMConfig perform
SCHWERWIEGEND: Fehler beim Aktualisieren von D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties
Weitere Einzelheiten finden Sie in der Log-Datei in D:\ORACLE\cfgtoollogs\emca\SAXMBS\emca_2009_09_15_13_15_52.log.
15.09.2009 13:25:02 oracle.sysman.emcp.EMConfig perform
KONFIG: Stack Trace:
oracle.sysman.emcp.exception.EMConfigException: Fehler beim Aktualisieren von D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties
at oracle.sysman.emcp.EMDBCConfig.performConfiguration(EMDBCConfig.java:405)
at oracle.sysman.emcp.EMDBCConfig.invoke(EMDBCConfig.java:167)
at oracle.sysman.emcp.EMDBCConfig.invoke(EMDBCConfig.java:137)
at oracle.sysman.emcp.EMConfig.perform(EMConfig.java:223)
at oracle.sysman.emcp.EMConfigAssistant.invokeEMCA(EMConfigAssistant.java:535)
at oracle.sysman.emcp.EMConfigAssistant.performConfiguration(EMConfigAssistant.java:1215)
at oracle.sysman.emcp.EMConfigAssistant.statusMain(EMConfigAssistant.java:519)
at oracle.sysman.emcp.EMConfigAssistant.main(EMConfigAssistant.java:468)
the problem is Caused by: java.io.FileNotFoundException: D:\ORACLE\product\11.1.0\db_1\sysman\config\emoms.properties (access denied)
and when i try to deconfig this following occured
15.09.2009 13:30:28 oracle.sysman.emcp.EMConfig perform
INFO: Dieser Vorgang wird in D:\ORACLE\cfgtoollogs\emca\SAXMBS\emca_2009_09_15_1
3_29_13.log protokolliert.
15.09.2009 13:30:28 oracle.sysman.emcp.util.DBControlUtil stopOMS
INFO: Database Control wird gestoppt (dies kann etwas lõnger dauern) ...
15.09.2009 13:30:28 oracle.sysman.emcp.EMConfig perform
SCHWERWIEGEND: Can't find file D:\ORACLE\product\11.1.0\db_1\host\sysman\config\emoms.properties
Weitere Einzelheiten finden Sie in der Log-Datei in D:\ORACLE\cfgtoollogs\emca\S
AXMBS\emca_2009_09_15_13_29_13.log.
Die Konfiguration konnte nicht abgeschlossen werden. Weitere Einzelheiten finden
Sie in der Log-Datei in D:\ORACLE\cfgtoollogs\emca\SAXMBS\emca_2009_09_15_13_29
_13.log.
Can't find file D:\ORACLE\product\11.1.0\db_1\host_db\sysman\config\emoms.properties
With Windows Server 2003 I haven't any problems with the configuration of database control over cmd.
Any Ideas?Please run the following command
cmd>net start OracleDBConsolexxx(Assume sid name=xxx
cmd>set oracle_sid=xxx
cmd>emca (You will get all related keyword of emca)
Firstly you have to check that if you have created your database through DBCA then you have to drop old repository or recreate repository:
To drop (remove) the configuration files and repository for Database Console, run:
cmd>emca -deconfig dbcontrol db -repos drop
To recreate (remove & create) the configuration files and repository for Database Console, run:
cmd>emca -config dbcontrol db -repos recreate
(Please mark it helpful/Answered if you get solution)
Regards,
Suman
Maybe you are looking for
-
Cannot open Word in Office 2011 after upgrade to Mavericks
Hi, Word is crashin while trying to open it. Error details as below: Microsoft Error Reporting log version: 2.0 Error Signature: Exception: EXC_BAD_ACCESS Date/Time: 2013-11-06 18:04:55 +0000 Application Name: Microsoft Word Application Bundle ID: co
-
Fiscal period to calender month FM
Hi Friends, Is there any function module to pass the fiscal period and fiscal year value and get calender date, month and year. Thanks & Regards, Vallamuthu.m
-
Unable to install 10.5 on windows xp, says older version of itunes can not be uninstalled
unable to install itunes 10.5, error message says network is unable to fin itunes.msi
-
TB will download 1, display 'not responding' for about 30 sec, then repeat.
This has become a recurring problem. TB will behave normally, then begin this action. During the not responding, the hourglass will display and the window will be unresponsive to any action. Frequently, downloading will cease completely after several
-
My iPhone won't connect to wi-fi because of personal hotspot
My iPhone won't connect to the available wi-fi source at home, personal hotspot has disappeared from underneath wi-fi on settings and when you go into personal hotspot in network, you can't turn personal hotspot off, 4 iPod touches 4th gen, 1 iPad an