Free international 800 calling to U.S. with skype
I will be residing in Thailand this winter and want to know if I will be able to call my bank in the U.S using their toll-free number? If so, will this call be free? Also, what format should I use when dialing this 800 number from Thailand to the U.S? Thanks for any input
goonfrog6 wrote:
I will be residing in Thailand this winter and want to know if I will be able to call my bank in the U.S using their toll-free number? If so, will this call be free? Also, what format should I use when dialing this 800 number from Thailand to the U.S? Thanks for any input
If you are able to reach that number using Skype, it would be a free call.
To dial the number from Skype, you would dial +1 followed by the toll-free area code and number (total of 10 digits after the +1). Please note that Skype does not guarantee calls to all toll-free numbers in the +1 country code. Some of these numbers are actually in countries other than the USA (i.e. Canada, Bermuda, many islands in the Caribbean, plus some US territories in the Pacific), or the company/organization that has the number has limited where incoming calls can come from (those with the toll-free numbers can restrict calls to come in only from specific states and/or area codes). Skype typically patches calls to US phone numbers, including any of the toll-free area codes, into the telephone network in California. The toll-free number you want to call must be reachable by someone calling it from California in order to reach it with Skype.
You can simply test this before you leave for Thailand with Skype. If you are not able to call that number with Skype, try to see if your bank offers a non-free number you can call. Sometimes these are listed as "Call Collect" numbers or numbers specifically for use outside the USA. You'd have to purchase Skype Credit or a subscription to call the non-free numbers, but that could be an option.
Good luck!
Patrick
Location/Ubicacion: Arizona USA
Time Zone/Hora Local: UTC/GMT -7
If this message has adequately addressed your issue, please click on the “Accept as Solution” button. If you found a post useful then please "Give Kudos" at the bottom of my post, so that this information can benefit others.
Si esto mensaje le ha ayudado, por favor haga clic en "Aceptar como solución". Si encuentra un mensaje útil, por favor "Da Kudos" al final del mensaje, por lo que esta información puede beneficiar a otros.
I am not a Skype employee. No soy un empleado de Skype.
Similar Messages
-
Free international phone calls
recently received a letter stating that if you had xfinity voice phone service, you would be able to make "free" calls to Singapore. Yet when i explored the international rates, they reflected a $0.12 charger per minute??????
recently received a letter stating that if you had xfinity voice phone service, you would be able to make "free" calls to Singapore. Yet when i explored the international rates, they reflected a $0.12 charger per minute??????
-
Problems calling Landlines in France with Skype Un...
Hi all,
I've signed up for the free trial of Skype Unlimited and am having a few problems calling a couple of landlines in France. Both numbers begin +33 (0)9... but are both normal French landlines (at least, calls to them in France are charged the same as any other house phone). So I was wondering if anyone knew why this might be the case?
Thanks in advance for any help/tips!I have also problems with +33 4 numbers and +33 5 numbers.
This is recent and was not the case before. -
Calling with Skype is it free?
Im just very confused, I live in Mexico and I just called a mobile phone with Skype and it actually worked... I tought I needed to buy some credit in order to actually place a call. Im using skype for windows 8 desktop over a Wifi connection.
Or is calling to mobile phones from Mexico to Mexico free now? I don't understandCurrently it's part of a 100 million free minutes promo (0 cents a minute, 0 cents connection charge).
http://everyday.skype.com/es-mx/mexico
Once the minutes are reached the promo will be over and the normal pay as you go rates will return (requiring credit or a subscription). That page displays the current minutes consumption. -
What is facetime audio and can I use it to make free international calls between iPhones?
what is facetime audio and can I use it to make free international calls between iphones?
First, check
1. Settings > General > Restrictions: should be OFF > FaceTime: ON?
2. Settings > FaceTime > FaceTime: ON?
ou can be reached by FaceTime at: your phone number?
If all the above are correct, see below:
FaceTime is available with iPhone 4 or latter, except those iPhones that were sold in the Middle East.
Can you tell us which iPhone model that has no FaceTime? -
Can i use iphone to iphone for free international call and text?
Can i use iphone to iphone for free international calls and text messages?
If both iPhone users are on iMessage, texting will be free, though there may be data charges if you do not have Wi-Fi. You can use FaceTime Audio in iOS 7 and later to call people but regular phone calls still count against your phone plan.
-
Phishing warning on Safari with toll free number to call
I was using google on Safari and suddenly I got a warning window saying that I was redirected to possible phishing site that would compromise my computer. and the window included a toll-free number to call (which I did not call). I quit Safari, came back on and I still got the phishing warning.
What do I do now?Quit Safari and relaunch it while holding down the shift key. This will close previously opened windows.
Clear the cache under the Safari menu. -
Cost for International Video Calls
I'm new to Skype and unable to find anything that will tell me if international video calls are free & if not, what is the cost
nexttime wrote:
I was wondering with the premium subscription does that include unlimited vido chat to places like to brazil, or in the USA, or neither?
Hello,
Video calls are only possible when you call someone on your Contacts list (Skype-to-Skype).
Skype-to-Skype calls are free worldwide.
TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
I recommend that you always run the latest Skype version: Windows & Mac
If my advice helped to fix your issue please mark it as a solution to help others.
Please note that I generally don't respond to unsolicited Private Messages. Thank you. -
IMessage free international?
so i heard iMessage is free international to other iPhones with the new ios5 software, is this true?
It doesn't guess, it pings and knows the other end is an iOS 5 device, sends it as an iMessage and shows you it has been delivered as an iMessage. At this point it is not using SMS at all.
I've sent a number of iMessages back and forth to several people and none of them have been listed as a text message with AT&T. So if Apple "screws up" how would it be working with AT&T but not with 3? Call them. -
ILBC calls via SIP Trunk with CUBE and CUCM7
hi there,
our SIP Provider offers the IBLC codec which promises to provide better quality compard to G.729.
I'm using this scenario:
IP-Phone(G711) --- CUCM7 --- (SIP-Trunk1) --- CUBE --- (SIP-Trunk2) --- Provider
Everything workes unless I'm configuring IBLC at the provider and on trunk2.
I have the CUBE router acting as a trancoding device and also specified IBLC as codec to be handled.
SIP trunk 2 was placed in a region with IBLC as codec.
On the trunk configuration in CUCM the media ressource group with XCODE capability is configured
Transcoding workes between two IP Phones in different regions with different codecs within the intranet.
Unfortunately the CUBE router doesn't seem to use the transcoder to change internal G711u calls into IBLC codec
so calls are blocked by the CUBE device:
deb ccsip calls
for incoming call:
.Mar 13 17:43:17.231: //145/BDB403DD8134/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x4AE7AC98
State of The Call : STATE_DEAD
TCP Sockets Used : NO
Calling Number : 0237892992
Called Number : 036677725231
Source IP Address (Sig ): 10.100.100.50
Destn SIP Req Addr:Port : <IP SIP Provicer>
Destn SIP Resp Addr:Port : <IP SIP Provicer>:5060
Destination Name : <IP SIP Provicer>
.Mar 13 17:43:17.231: //145/BDB403DD8134/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : ilbc
Negotiated Codec Bytes : 0
Nego. Codec payload : 255 (tx), 255 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): <IP CUBE>
Source IP Port (Media): 0
Destn IP Address (Media): <IP SIP Provicer>
Destn IP Port (Media): 22022
Orig Destn IP Address:Port (Media): [ - ]:0
.Mar 13 17:43:17.231: //145/BDB403DD8134/SIP/Call/sipSPICallInfo:
Disconnect Cause (CC) : 65
Disconnect Cause (SIP) : 488
(Output lookes similar to outgoing calls)
I set up ccm on cube and assigned dsp ressources without success:
Here are the relevant configuration parts:
voice class codec 1
codec preference 1 iblc
voice service voip
address-hiding
allow-connections sip to sip
allow-connections h323 to sip
allow-connections sip to h323
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
h323
sip
header-passing error-passthru
no update-callerid
midcall-signaling passthru
privacy-policy passthru
voice-card 0
dspfarm
dsp services dspfarm
dial-peer voice 40991 voip
description *** Incoming from SIP-Provider
destination-pattern 03667772523.%
session protocol sipv2
session target ipv4:<IP_of_CUCM>
voice-class codec 1
voice-class sip asserted-id pai
voice-class sip privacy-policy passthru
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
ip qos dscp cs5 media
ip qos dscp cs5 signaling
sccp local GigabitEthernet0/0
sccp ccm 10.100.100.50 identifier 11 version 4.1
sccp
sccp ccm group 11
description *** lokaler CCM fuer Codec-Konvertierung von SIP/DUS.NET
associate ccm 11 priority 1
associate profile 21 register DE_WGT_MTP02
dspfarm profile 21 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec ilbc
maximum sessions 10
associate application SCCP
telephony-service
sdspfarm units 1
sdspfarm transcode sessions 10
sdspfarm tag 1 DE_WGT_MTP02
max-ephones 30
max-dn 30
ip source-address 10.100.100.50 port 2000
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp 7960 Mar 14 2010 02:10:34
sh sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 10.100.100.50
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 10.100.100.50, Port Number: 2000
Priority: N/A, Version: 4.1, Identifier: 11
Trustpoint: N/A
Call Manager: 10.1.1.55, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 10
Trustpoint: N/A
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 10.100.100.50, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 21
Reported Max Streams: 20, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: ilbc, Maximum Packetization Period: 120
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
sh dspfarm dsp all
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 1 26.3.4 UP N/A FREE xcode 1 - - -
0 1 26.3.4 UP N/A FREE xcode 1 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 1 - - -
1 1 26.3.4 UP N/A FREE xcode 1 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
Thanks in advance,
DavidHi there,
Just wondering whether you ever got this resolved? I seem to have a very similiar problem.
Regards
Karen -
I found several charges on my bank account from Apple on App that is completely free. After calling the number showing on my bank statement there an automated answering that tells you to go to apple website!!! There is nobody to talk to!! Complete rip OFF
And now because I want to communicate with apple support I have to go through the hectic website and community support, this is ridiculous.
I have 5 iPhones in my account and this makes me reconsider upgrading to iPhones again.
Why Apple put a phone number in the bank transaction, if there is nobody to talk to!!!!!!
I hope someone from Apple support can answer my question.Go to getsupport.apple.com. Or, call 1-800-MYAPPLE.
Just because an app is free to download doesn't mean that there aren't in-app purchases available.
Go to iTunes on your computer, log into the iTunes Store with your Apple ID & password, and check your purchase history. Be advised that all iTunes & App Store purchases are final. -
CALLER ID not working for International incoming calls
Hi,
I've a strange issue where CALLER ID not working for International incoming calls, it shows INTERNATIONAL UNKNOWN NUMBER in the phone display, but the number shows correclty in Verizon Call assistant !!!
Any clue?yashshankar wrote:
Hi
I recently purschased an Online number but the caller id does not work for incoming calls.How do we resolve this problem?.
Regards
Yash
You didn't mention what country your Online Number is in. Not all of Skype's Online Numbers are eligible for use as Caller ID when calling telephones or sending SMS messages. If your number is from one of these countries (Chile, Denmark, Estonia, Hong Kong, Poland, Sweden, the UK and the US), then it can be used this way. Otherwise, you can use a mobile number from countries other than Japan or Mexico as Caller ID with Skype, after the number goes through a verification process where Skype sends SMS messages with codes to that number.
To get to these settings, log into your Skype account here on the Skype web site using the "Account" link at the top of this page. You'll see a screen that would include your current Caller ID settings, and a link to change that. If your Online Number is from one of those countries I referenced above, just select it and you're done.
Hope that helps!
Patrick
Location/Ubicacion: Arizona USA
Time Zone/Hora Local: UTC/GMT -7
If this message has adequately addressed your issue, please click on the “Accept as Solution” button. If you found a post useful then please "Give Kudos" at the bottom of my post, so that this information can benefit others.
Si esto mensaje le ha ayudado, por favor haga clic en "Aceptar como solución". Si encuentra un mensaje útil, por favor "Da Kudos" al final del mensaje, por lo que esta información puede beneficiar a otros.
I am not a Skype employee. No soy un empleado de Skype. -
Trouble with Skype. can't hear caller but I can see caller.
Trouble with Skype. Caller cannot hear me but I can hear caller. Cannot hear voice on test call. Can see caller. MIcrophone is on and volume turned up.
Michele,
I do not have Mavericks running on my older MacBook Pro. During the call, do you have the microphone icon on the Skype window enabled or disabled? Have done that before.
My Skype preferences:
Microphone: Built-in Microphone (Internal microphone)
* Automatically adjust microphone settings is set
Ringing and Speakers: Built-in Output (Internal Speakers)
Camera: Built-in iSight.
System Preferences > Sound
Input tab: Internal Microphone
Output tab: Internal Speakers -
Available internal storage zero after problem happened with iCloud shared photo stream
after I tired to upload large amount of photos to iCloud shared photo stream(2gb), which is larger than the available internal storage (only 300 mb left ). and then my iPhone stop me from uploading , said that my phone got no sufficient storage available . so, I cancel the upload, but my available internal storage is still zero. I don't know what to do, and I delete the whole (empty) album, which I targeted to upload photo to it. but even after I delete the album, my available internal storage is still zero. it suppose to return my free space(return to 300mb of free space). can any one help me with this ??
i tried to delete apps to free up the space. i tried to delete a few apps and I manage to get back 200 my of free space but after a short while, the available free space go back to zero again...d my phone to be zero available internal storage.
thanks any reply reply reply in advance.Same problem here.
-
What is an Apple Support Toll Free Number to call in the region of Los Angeles California, United States?
I need Apple Support because i have an issue. Can you also give the hours of opperation/opening hours?U.S. iPod, Mac and iPad technical support:
(800) APL-CARE (800-275-2273)
Maybe you are looking for
-
Notes at the Item level is not getting Copied
Hi All, When a quotation is copied by clicking on the "Copy" button, the new quotation has all the Notes copied at the header level. But all the Notes maintained at the Item level dosent get copied. The Copy control has been maintained between the It
-
SSH and media wiki not connecting from outside of my LAN
I cant seem to connect to ssh or my mediawiki server from outside of my LAN. Ive forwarded all the needed ports and been going over my config all night. I also made sure my router wasn't blocking anything. -ssh tells me connection denied -when i go t
-
In PR only base uom can be used - Why not order unit ?
Hi All, When I create PR for raw material, SAP by default takes the base UOM. But our stack holders wants to use Order unit in the PR. What is the setting required to use order unit in PR. If this can't be done - what is the note number to support th
-
File type is corrupt or wont play
I just posted my first podcast, I have it playing on other podcatchers but when I try to download it from itunes I get an error message that the file type is corrupt or not supported. It's in mp3 format. How can I fix this, or resubmit it?
-
Hi, I am currently coding an Abap program using version R/3 release 4.6C. The idea is that this program can be ran from R/3 or the portal. My question is how can I within the program know from with system the program is being called? Hope I have give