FreeNAS 9.3 with HP M6412-A Fibre Channel Drive Enclosures

Hi,I have acquired two HP M6412-A Fibre Channel Drive Enclosures with 14 dual-port SAS15K disk drives (7 per enclosure) in a recent company takeover.I do not have any HP software licenses for the HP EVA4400 Dual Controller Array that came with the disk enclosures. HP wants more than $15k to re-license the EVA, so that is not an option.I took an older HP DL380 G5 server with 48GB RAM and added a HP StorageWorks 82Q 8GB PCI-e Dual Fibre Channel HBA (AJ764A) and connected the twodisk enclosures with the server. The server also have 4 x 1GB and 4 x 10GB ethernet ports.On the server HP Server I have loaded FreeNas 9.3 and I use the server and disk enclosures as a very capable SAN.The HP M6412-A Fibre Channel Drive Enclosures have two Fibre channel ports (red and green), but I have only connected the enclosures with one Fibre Channel loop to...
This topic first appeared in the Spiceworks Community

Similar Messages

Sun V880 Fibre channel drive giving Loop OFFLINE message

Hi
I have a v880 with two drives and drive at slot 0 is giving below message every few minutes and drive operation (read and write) halts.
Jul 12 12:36:11 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop ONLINE
Jul 12 12:36:28 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop OFFLINE
Below is message i am seeing in /var/adm/messages.
# tail -f /var/adm/messages
Jul 12 12:34:59 suntest1 scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w2100000c50eb2098,0 (ssd1):
Jul 12 12:34:59 suntest1 SCSI transport failed: reason 'tran_err': giving up
Jul 12 12:36:00 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop OFFLINE
Jul 12 12:36:01 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop ONLINE
Jul 12 12:36:05 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop OFFLINE
Jul 12 12:36:06 suntest1 scsi: [ID 243001 kern.warning] WARNING: /pci@8,600000/SUNW,qlc@2/fp@0,0 (fcp0):
Jul 12 12:36:06 suntest1 PLOGI to D_ID=0xef failed: State:Operation Success, Reason:Undefined. Giving up
Jul 12 12:36:11 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop ONLINE
Jul 12 12:36:28 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop OFFLINE
Jul 12 12:36:34 suntest1 qlc: [ID 686697 kern.info] NOTICE: Qlogic qlc(0): Loop ONLINE
System is running solaris 9 and I have following qlogic driver installed.
# modinfo|grep qlc
26 1215a7d 26c61 153 1 qlc (Qlogic FCA Driver v0.40.5)
Any help will be appreciated.
Thanks
Anoop

What is the status of the HDD of this particular path ?
WARNING: /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w2100000c50eb2098,0 (ssd1):
You can verify with format or iostat -En
Regards
Ravi

Does fibre channel use both ports on the same drive bay

I would like to know if Fibre Channel uses both of the fibre ports when they are connected to the same fibre channel drive bay. (dual port communication)

I would like to know if Fibre Channel uses both of the fibre ports when they are connected to the same fibre channel drive bay. (dual port communication)

Problem with fibre channel card and raid system after upgrading to 10.4.7

Hello, I have a problem with our Xserve G4 DP. After the installation of 10.4.7 everything works fine exept our fibre channel card. This card is connected to a Hitachi Raid System which worked fine over a year. But after the update the volume was no longer mounted. I even reinstalled the server to 10.4.4 and no sign of our raid volume. Using the apple fibre channel utiltiy 2.0, I see that there is a connection - but still the raid volume is not mounted. When I restart the server the lights on the back of the card are shortly flickering and sending some packets to the raid system but that´s all. Has anybody an idea?
Greetings from Heidelberg
Klaus
Xserve G4 DP 1 GHz Mac OS X (10.4.6) Mac OSX Server 10.4.7

You could re-update, by downloading the 10.4.7 Combination Updater from Apple.

Hi, we have a G5 Blade server running OS X 10.5.8 with a dual Fibre Channel card. The OS does not read the card and cannot establish connection to the RAID controller. I have tried to move the card to another port with no luck. Ran all the updated softwar

Hi, we have a G5 Blade server running OS X 10.5.8 with adual Fibre Channel card. The OS does not read the card and cannot establishconnection to the RAID controller.
I have tried to move the card to another port with no luck.Ran all the updated software possible. Please can someone advice

Hi,
Was the card previously working in that machine? If it was and you have a G5 tower you could try the card in there. Here is a list of Apple fibre cards and cables which show what's compatible with what. http://support.apple.com/kb/HT1769
The card should appear in the System Profiler under Fibre Channel and PCI Cards.
All the best
Beatle

The Fibre Channel Platform Registration Service could not register the platform with fabric

Hyper-V Cluster. HP StorageWorks 82E 8 Gb PCI-e Dual Port FC HBA.
Each 15 minutes, eventlog register a warning.
EventID: 2 Source:2
The Fibre Channel Platform Registration Service could not register the platform with fabric 10:00:00:05:1e:7f:74:7b.
I have teste the service. And it's started. Cluster storage validation report without failure.
Someone suggest any idea.
Thanks.

Hi,
What’s the OS version of your cluster node?
The Microsoft Fibre Channel Platform Registration Service registers the platform with all available Fibre Channel fabrics and maintains the registrations. A fabric is a network topology where devices are connected to each other
through one or more high-efficiency data paths. This service is used in support of storage area networks.
This service is installed by default on Windows Server 2008, and the service startup type is Manual.
You may try hotfix in KB 978790, and check the result.
For more information please refer to following MS articles:
The File Share Witness resource is in a failed state even though the File Share Witness directory is available, and quorum cannot be maintained in a Windows Server 2008 failover cluster
http://support.microsoft.com/kb/978790
cluster resources unresponsive
http://social.technet.microsoft.com/Forums/hu/winserverClustering/thread/886a9cb3-7723-4b64-8c15-602dadf5ced9
Hope this helps!
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Lawrence
TechNet Community Support

Xserver Fibre Channel with tape backup issues?

Is this correct, that OS X 10.4.9 and 10.4.10 has a fibre channel issue with external tape drives (as well as SCSI drives)???
And this is to be fixed in 10.4.11? Do we have a time frame when we will see 10.4.11 to fix this major snafu?
I'm going to decide on a different server (in the meantime) and do net backups if this is the case. But what about others that run backup off the server, attached to an Xserve RAID?
BTW, I contacted BRU support with query on their software...I give kudos to them. Their support is spot on!
Message was edited by: Eddie Ski

Retrospect is just hideously, egregiously out of date and I don't think EMC gives a d*mn, at all.
Even pre-Intel, it will happily LOCK up your server while failing to properly time out when trying to talk to a tape library. It's well-known, Retro + Tape Library = h*ll on earth. And the fault lies squarely with Retro because something like Bru and other more expensive software does not have the same issue.
So let's just make sure -not- to judge "SCSI" isues in OS X based on the ungodly-awful behaviour of Retrospect. Might as well do automobile performance tests using only amateur drivers ; )

Super Slow Performance with Xserve RAID / Promise Fibre

Hey guys,
I am experiencing a strange thing on both 10.5.8 and 10.7.5 servers (yes these are in the process of being retired). They are sharing out either an Xserve RAID or Promise Vtrak with OS X Server.
We have the fibre channel card and the storage attaches to there and they appear mounted on the desktop.
The problem we are having is that whenever OS X's file sharing is enabled these volumes run incredibly slow! I did a clean install of OS X 10.7.5 on an entirely different machine and it was still bad. All of my tests show that when you turn off file sharing, both AFP and SMB, the performance goes back to normal -- so what can we do here??? These are file servers, so that's pretty much the only thing that needs to work.
Thanks,
Andrew

Slow/poor RAID performance can be down to a number of things. Some of which are easier to check than others.
Some easy things to check are:
How much data is stored on the RAIDs?
Performance really drops off alarmingly once the RAID gets to 85% full. For a 1TB RAID this means you need to keep at least 250GB of free disk space at all times otherwise you will get the poor performance you're seeing. Once it gets to 86/87/88% full performance can drop alarmingly. Yes those few percent points can make a big difference.
How is the data stored on the RAIDs?
Having thousands and thousands of single files stored loosely on the RAID or within one single folder is not a good idea. The Finder can be and is fairly inefficient at drawing the icons for those files that are presented to network users accessing the share point(s). This can/and is perceived as very slow performance as you're viewing the files over a network connection. One way to overcome this 'feature' is to organise the data into logical folders/sub-folders and/or shares.
Are there problems with the file/directory structure of the RAIDs themselves?
Use DiskUtility (or better still DiskWarrior) to repair any issues (generally built up over a period of time) with the storage disks you have. You can't repair permissions using DiskUtility or anything else on a non-OS bearing drive. Don't forget to do this also for your System Drive (which can have its permissions repaired) as well. This will mean the server being off-line for a time whilst the system (OS) drive is being repaired. Before doing this step I would make sure you have a current and effective backup of your System/Server OS as well as all data stored on the RAIDs themselves. Hopefully you should be doing this for your data already?
To understand Disk Utility's repair permissions feature please read Apple's support document here:
About Disk Utility's Repair Disk Permissions feature - Apple Support

How to obtain target WWN for a LUN On Windows 2012 R2 Hyper-V with Fibre Channel SAN

I have a large collection of Hyper-V hosts for which I would like to retrieve the target WNN and LUN ID for the LUNs visible on each host. By target WWN I mean the storage array's WWN.
I have tried using the root\wmi namespace to retrieve MS_SMHBA_PORT_LUN instances, but I get 0 instances back.
I get instances of MSFC_FibrePortHBAAttributes back, but those only tell me the local host's HBA WWN, not the target information.
This information must be stored somewhere, because you can't access the LUN without it, I hope there is a way to retrieve it. Is there? Or is it write only during LUN setup?

Hi,
Have you checked these two postings:
http://terrytlslau.tls1.cc/2011/08/how-to-find-world-wide-name-wwn-in.html
http://pkjayan.wordpress.com/2011/08/17/world-wide-name-wwn-for-a-fibre-channel-hba-on-windows-server/
You need the FCINFO tool, which you can get from:
http://www.microsoft.com/en-us/download/details.aspx?id=17530
Cheers
Andrew

Clarification on how to use Xserve Raid and Fibre Channel without xsan.

First let me apologize for not responding earlier to your response, I tend to get busy and then forget to check back here.
Tod, the answer to your question is No, only one computer is accessing the xserve raid files at any one time and that is via Fibre Channel. However I do have the xserve raids set up as share points via ethernet.
Maybe I should turn that off and only access the files with the one computer that can connect via fibre channel.
I never thought of that. I will try that while I await for your answer, thanks again.
Todd Buhmiller
I have the following setup:
Xserve: 2x2Ghz Dual Core Intel Xeon, 5Gb of Ram, Running 10.5.8 Leopard Server
Xserve Raid with firmware version 1.5.1/1.51c on both controllers, and
Qlogic Sanbox 5600
Apple Fibre Channel Cards in Xserve, and Mac Pro Tower; Apple 2 Port 4Gbs Fibre Channel Card
Mac Pro Tower-Quad Core Intel Xeon 2.8Ghz, 16Gb of Ram, Running Snow Leopard 10.6.4
Here is the problem.
The directory for the xserve raids keep getting corrup, and I use disc warrior to rebuild them. Is there a way to keep the directories from getting corrupt? I am a few pieces of equipment before I can build an Xsan as that is the ultimate goal, but until then, I just need to be able to have the raids funciton as storage without having to rebuild the directories all of the time.
Anybody have any suggestions?
Thanks
Todd Buhmiller
Widescreen Media
Calgary, Alberta Canada
Tod Kuykendall
Posts: 1,237
From: San Diego
Registered: Oct 11, 2000
Re: Xserve Raid Mounts, Corrupt Directory tired of rebuilding directory
Posted: Jun 27, 2010 1:25 PM in response to: Todd Buhmiller
Are multiple computers accessing the same data on the RAID at the same time?
If so then NO. This is the source of your data corruption and I'm surprised if you were able to get all your data back every time if this is how you've been running your system. Each fibre channel assumes it has full and sole control of every volume it has mounted, no data arbitration is practiced and data corruption will occur if this assumption is wrong.
The only way this set-up will work is to use partitions or LUN masks so the volumes are accessed by one computer at any time. As long as one computer relinquishes control before another mounts it you will dodge arbitration issues but this is a dangerous game. If you screw up and mount an already mounted volume - and there is no easy way to tell if a volume is mounted - corruption will then occur. Sharing data simultaneous at fibre speeds is what XSAN does and to do this you need it.
HTH,
=Tod
Intel Xserve, G5 XServes, XRAID, Promise

+The xserve raids will mount automatically to any computer that I connect the qlogic fc switch to+
This is source of the corruption to your data. Any computer that attaches to a drive/partition via fibre channel assumes that it alone is in control of the drive and data corruption is inevitable.
+Is that the issue, should I disconnect the xserve from the fc switch and leave it connected via ethernet?+
Short answer: YES. The ethernet connections are fine because the server is controlling the file arbitration through the sharing protocol. Fibre channel connections assumes complete control over the partition and no arbitration of the file access is performed. It's like two people independently driving trying to drive the same car to different locations.
Depending on your set-up it is possible for the two machines to see and use different parts of the Xserve RAID storage but they cannot access the same areas without SAN doing the arbitration.
Hope that's clear,
=Tod

Can I hook up a NAS via Fibre Channel?

I am building a Linux NAS to be accessed by my Macs. I've purchased fibre cards for all of my macs, an LSI fibre card for my Linux machine, and a McData 4400 fibre switch. I'm trying to configure my fibre network so I can share files from my NAS. I've got the fabric set up, but everything that I read is talking about using SAN software to connect to a SAN, not a NAS. I can't find any information at all on how to do what I want to do, or whether or not it's possible. Can someone please help me figure out how to set up this Fibre Channel network, or at least figure out if it's possible or not? Thank you!
-Ryan

Is what you want technically possible? Probably.
In an earlier era, you could have a network or an image scanner or other devices connected to a host via SCSI; via a storage bus. There was all manner of odd SCSI-connected gear. (Think of SCSI as expensive multi-host USB with big expensive cables and with expensive peripheral devices, and you'll have the general idea. And FWIW, SCSI is the underpinnings of USB.)
You would end up writing a whole lot of driver code for the devices and hosts you have, too.
Which is where folks end up with commercial SAN solutions, or with NAS solutions, and not with using a SAN as a network.
The various Fibre Channel controller vendors discussed but never seemed to have sorted out the network interface designs for their FC controllers.
If you want to roll your own storage arrays akin to the [Apple Xsan|http://www.apple.com/xsan> or the HP [MSA|http://h18000.www1.hp.com/storage/diskstorage/msa_diskarrays/sanarrays/index.html] or [EVA|http://h18000.www1.hp.com/storage/diskstorage/eva_diskarrays/evaarrays/index.html] SAN arrays, well, have at. You'll likely end up needing to write host disk drivers, as well as the firmware within the SAN controller. Networking drivers might be a bit more tricky; I haven't looked at those device interfaces in a while, and you'd need to tie those drivers into the host network stacks. Once you have some or all of that working, then the hosts can see the block storage out on the SAN. If you need sharing, you'll need to sort out a cluster or SAN file system to run atop the block storage or atop the network connection you've built; a file system that can coordinate distributed access.
Possible? Sure. On a budget? Probably not.

Need docs that explain Fibre Channel setup, getting I/O error on 2540 SAN

Sun T5220 Host running Solaris 10 5/09 as management host.
Qlogic 5602 FC Switch
Sun Storagetek 2540 - one controller tray with 9 300G SAS Hitachi drives. Firmware 7.35.x.
Sun branded Qlogic QLE2462 HBAs - PCI express, dual port. 3 in the T5220. qlcxxxx drivers for the HBAs.
Sun Common Array Manager software version 6.5.
I am a long-time Oracle DBA who has the task of setting up a Fibre Channel SAN. I am not a Solaris sysadmin, but have installed and maintained large databases on Solaris boxes where I had access to a competent sysadmin. I am at a classified site and cannot bring out electronic files with logs, configuration info, etc. to upload. Connecting the T5220 is the 1st box of many. This is my first exposure to HBA's, Fibre Channel, and SAN, so everything I know about it I have read in a manual or from a post somewhere. I understand the big picture and I have the SAN configured with 2 storage pools each with 1 volume in them on RAID5 virtual disks. I can see the LUN 0 on the T5220 server when I do a luxadm probe and when I do a format. I formatted one of the volumes successfully. Now I attempt to issue:
newfs /dev/rdsk/device_name_from_output_of_luxadm_probe
I get an immediate I/O error. I could be doing something totally naive or have a larger problem - this is where I get lost and the documentation becomes less detailed.
What would be great is if anyone knows of a detailed writeup that would match what I'm doing or a good off-the-shelf textbook that covers all of this or anything close. I continue to search for something to bridge my lack of knowledge in this area. I am unclear about the initiators and targets beyond the fundamental definitions. I have used the CAM 6.5 software to define the initiators that it discovered. I have mapped the Sun host into a host group also. I do not know what role the Qlogic 5602 Fibre Channel switch plays with respect to initiators and targets or if it has any role at all. Is it just a "pass through" and the ports on the 5602 do not have to be included? Maybe I don't have the SAN volume available in read/write. I find bits and pieces in blogs and forums, but nothing that puts it all together. I also find that many of the notes on the web are not accurate.
This all may appear simplistic to someone who works with it a lot and if you know of an obvious reference I should be using, a link or reply would be greatly appreciated as I continue to Google for information.

Thanks for the reply. I had previously read the CAM 6.5 manual and have all the SAN configuration and mappings. Yesterday I was back at the site and was able to place a UFS filesystem on the exposed SAN LUN which was 0. I've not seen any reference to LUN 0 being a placeholder for the 2540 setup and when I assigned it, I allowed the CAM 6.5 software to choose "Next Available" LUN and it chose 0. LUN 31 on the 2540 is the "Access" LUN that is assigned automatically - perhaps it is taking the place of what you describe as the LUN 0 placeholder.
I was able to put a new UFS filesystem on LUN 0 (newfs), mount it, and copy data to it. The disk naming convention that Solaris shows for the SAN disks is pretty wild and I usually have to reference a Solaris book on the standard scsi disk name formats. My question/confusion at the moment is that I have 3 Sun branded Qlogic HBA's in the Sun T5220 server - QLE2462 (dual port) with one port on two of the HBAs cabled to the Qlogic 5602 FC switch which is cabled to the A and B controller of the SAN 2540 - there are only 2 cables coming out of the 5220; the 3rd HBA (for future use) has no cables to it. Both ports show up as active and connected on the server down to the SAN and the CAM 6.5 software automatically identified both initiators (ports) on the Sun 5220 when I mapped them. I had previously mapped them to the Sun host, mapped the host to a host_group, virtual disks to volumes, volumes to....etc.; and was able to put data on the exposed volume named dev_vol1 which is a RAID5 virtual disk on the SAN.
When I use the format command on Solaris, it shows two disks and I assumed this represented the two ports from the same host 5220. I was able to put a label on one of these disks (dev_vol1), format it, and put data on it as noted above. When I select the other disk in the format menu, it is not formatted, won't allow me to put a label on it (I/O error) and I can go no further from there. The CAM 6.5 docs stop after they get you through the mapping and getting a LUN exposed. I continue on the in a Solaris-centric mindset and try to do the normal label, format, newfs, mount routine and it works for the one "disk" that format finds but not for the other. The information from the format info on both the disks shows them as 1.09 TB and that is the only volume mapped right now from the SAN so I know it is the same SAN volume. It does not make sense that I would label it and format it again anyway, but is this what I am supposed to see - two disks (because of 2 ports?) and the ability to access it through one. I found out by trial an error that I could label, format, and access the one. I did not do it from knowledge or looking at the information presented....I just guessed through it.
I have not "bound" the 2 or HBAs in any way and that is on my list as next because I want to do multipathing and failover - just starting to read that so I may be using the wrong language. But I am wondering before I go on to that, if I am leaving something undone in the configuration that is going to hamper my success in the multipathing - since I cannot do anything with the 2nd "disk" that has been exposed to Solaris from the SAN. I thought, after I labeled, formatted and put a filesystem on the one "disk" I can write to that the other "disk" that shows up would just be another path to the same data via a 2nd initiator. Just writing that does not sound right, but I am trying to convey my thoughts as to what I logically expected to see. Maybe the question should be why am I seeing that 2nd "disk" in a Solaris format listing at all? I have not rebooted any time during this process also and can easily do that and will today.

Receiving fibre channel activity log email when unplugging usb flash drive

I found this to be very interesting.... I get the email from the log of the machine I am on.... this happens EVERY time I unplug my SanDisk CRUZER GATOR 8GB Flash Drive. I have a couple other non-sandisk drives and it doesnt seem to cause the same thing.
this really doesnt effect our xsan or anything, but its annoying and it worries me that it could screw something up potentially.....so I am just wondering if anyone else is experiencing this?? or would know why this happens with just the sandisk...
This is on a MacPro 2 x 3ghz dual core xeons, 4gb memory. xsan 1.4.2
contents of the email:
Fibre channel activity and failures:
16:03:53: LUN 00:00:00:00:00:00:00:001 is no longer available
16:03:53: LUN 00:00:00:00:00:00:00:000 is no longer avail...
Message was edited by: RoyMan

We received this alert also:
Fibre channel activity and failures:
14:27:05: LUN 00:00:00:00:00:00:00:001 is no longer available
14:27:05: LUN 00:00:00:00:00:00:00:000 is no longer avail...
And we were using a SanDisk 8GB Cruzer USB flash drive as well.
Client is Mac Pro / Two 2.66GHz Dual-Core Intel Xeon / 2BG RAM / Xsan 1.4.2.

OSX 10.5.6 doesn't see Fibre Channel Disk array, neither does Disk Utility

My system is a Power Mac G5 Quad, 6gb Ram, 1Tb internal hard drives, 1Tb external and several portable drives as needed.
The Drive array in question is a Fujitsu GR710 which contains 12 Seagate Cheeta ST336605FC drives which are around 35gb each.
OK, I have been given a Fibre Channel system, that at one time worked with OSX. I had to move it and now it doesn't show up on Disk Utility anymore. I can totally reformat it if possible, but I have to be able to see it first.
System Profiler sees the setup as:
Fibre Channel Domain 0:
Vendor: LSILogic
Product: LSI7202EP
Revision: Firmware 1.2.18.0, Fcode 1.00.37
Bus: PCI
Slot: SLOT-2
Initiator Identifier: 126
Node World Wide Name: 20:00:00:06:2B:12:C4:C4
Port World Wide Name: 10:00:00:06:2B:12:C4:C4
Address Identifier: 00:00:E8
Description: Port 0
Speed: Automatic (1 Gigabit)
Topology: Automatic (Arbitrated Loop)
Status: Link Established
Cable Type: Fiber Optic
SCSI Target Device @ 0:
Node World Wide Name: 20:00:00:E0:00:41:04:6D
Port World Wide Name: 21:00:00:E0:00:41:04:6D
Address Identifier: 00:00:EF
SCSI Target Identifier: 0
SCSI Peripheral Device Type: 0
Manufacturer: FUJITSU
Model: GR710
Revision: 0000
SCSI Logical Unit @ 0:
SCSI Logical Unit Number: 0
Manufacturer: FUJITSU
Model: GR710
Revision: 0000
Fiber Channel Preferences shows that a link is established.
Hardware RAID says that there is no hardware present.
I am using the Apple MA900A/G Fibre Channel Card to hook into the Drive array. It is hooked up with both ethernet and fiber optic cables.
I have used an IP scanner to search for the IP of the array and only find one that I can't identify at 224.0.0.251 another scan reports an IP of 0.0.0.0, neither worked when I tried to use Safari to access it.
I have tried several programs to try and get into this array and nothing sees it. All my experts tell me that I will need to use the Terminal program and use command lines to access the drives, but I can't find any information about what to do there. I've been told I need the driver for the array, naturally there isn't a driver for Mac to be had, but there are drivers for solaris, Unix, and windows. The last expert said to use the Unix driver, but I don't know where to put it in the system.
So I need help, Terminal commands to talk to the drive and revive it hopefully, or a system program that will do something similar. None of my diagnostic programs sees the array. The Card came with no software or instructions. Neither did the array. I haven't been able to find any hardware information about the drive from FuJitsu at all, it's too old for them to bother with anymore.
Any help would be greatly appreciated!
Thanks
Doc

I have to go with William on this one - if it's shows up over fibre then it should be okay. Have you gotten the admin module to see the device over ether? I have a feeling that is you can get the software to see it you might be able to configure the device into something the computer could mount.
The Promise that way - you can configure the device entire from the web interface and you don't need fibre communication working for any of the configuration of what RAID you want and which disks are attached with what set etc. Once the RAIDs are configured into volumes then the Xserve sees they exist and you can use Disk Utility to format them. If you don't need fibre communication I don't see how SCSI drivers would matter over ethernet. But maybe the box is a strange beast - odder things have been made.
Barring that - can you attach the device to an older machine with the drivers and configure the device into raw volumes and then an HFS+ (or whatever you want) system? If you did that and then switched the box back to Xserve it should be able to pick up the configured volumes drivers or no.
My $.02,
=Tod

Whole root zone and fibre channel hba

I have Solaris 10 x86 loaded up on an IBM blade. I've created a whole root zone on it and have installed Symantec NetBackup 6.5.5 and configured it as Media Server. I have an SL8500 tape library in the environment and all the tape drives are fibre channel. Now, in the global zone, I can run fcinfo hba-port or scli and the global zone finds the hba's with no problem. I've added the /dev/cfg/c1 and /dev/cfg/c2 devices to the zone, but running the commands, it cannot find the hba's at all.
Is there something else that I need to do so that the zone can see the hba's, or is this just not possible in a zone?
Thanks in advance,
Ed Coates

Hi.
Check release notes for Netbackup. As i know Media Server is supported anly at Global zones.
You can add access to /dev/rmt/* and give access to tapes, but stiil problem with robot device and this configuration not supported.
Regards.

FreeNAS 9.3 with HP M6412-A Fibre Channel Drive Enclosures

Similar Messages

Maybe you are looking for