Freezing Ipod since recent Update

Hi,
So i updated my ipod recently to the 28-06 updater.
The problem is that after every couple songs, my ipod will freeze at the start of a song (0:00).
Every time this happens i have to reset my ipod (it happens alot).
Ive tryed restoring my ipod and that doesnt seem to help either.
Please can someone help me?

My only suggestion is to use the updater to Restore the ipod - maybe something went wrong with the update process.
Unlike the update, restore completely erases your ipod and returns it to factory settings. You will have to reload all your music so make sure it is backed up.

Similar Messages

  • Itunes not recognising ipod since recent update

    I last used itunes about 1.5 weeks ago to purchase a song and sync to ipod. I'm pretty sure since then I installed an itunes update.
    I uploaded a new album today and connected my ipod. My computed makes a noise when the ipod connects however no ipod icon is appearing in itunes and neither itunes or ipod is syncing. I 'troubleshooted it and there is a problem with the driver, the message when you go into the device manager says.....
    'Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or might be malicious software from an unknown source (code 52)'
    I am using Windows 8
    Does anyone have a clue what I should do??
    Help!
    Amanda

    Hey jmpiper32,
    There's an article that addresses that specific error message, which you can find here:
    iPod nano: Error message saying that iPod 'could not be identified properly'
    http://support.apple.com/kb/TS3218
    I'd run through the recommendations in that link to resolve the issue.
    Welcome to Apple Support Communities!
    Have a good one,
    Delgadoh

  • Since recent updates, I have noticed that my apps close automatically when I am distracted. In some cases it is time consuming to sign back in and get back to the task I was doing. Is it possible to change a setting so the apps will stay open?

    Since recent updates of iOS, I have noticed when using my iPad that my apps close automatically when I have to leave the room or am otherwise distracted for a few minutes. It is sometimes time consuming to sign back in and get back to the task where i left off. Is there a setting I can change so it will keep the apps open until I am ready to close them? Thanks for your help.

    Did you have this problem before Restoring you iPad?
    If you did then did you restore with a backup. You may have reinstalled something that is conflicting in this back up
    If not then sounds like either something went array with the clean install or a hardware issue.
    I know it's long winded but have you tired a clean install then downloading the apps again?
    PJRS

  • I have a ipod, but recently updated my laptop, how do I get my ipod to sync with my new PC, when I connect the USB the ipod say's "connected" eject before disconnecting

    I have a ipod, but recently updated my laptop, how do I get my ipod to sync with my new PC, when I connect the USB the ipod say's "connected" eject before disconnecting

    See KB Article:  How to use your iPod to move your music to a new computer

  • Adobe Premiere freezing after most recent update

    Hey all,
    I posted in here a while back because I was working with MTS files and seemed to be having an issue out of the blue with my projects freezing, where the video would play, but the cursor and anything I would click or move would not respond.
    I ended up transcoding to Prores and finished the edit. 
    BUT!!!  Even in the prores version this happened again, and I finally tied it to the universal counting leader.  Now I've used this thing many times before with no problems.  But since the most recent update (I'm now running CC v8.1.0) this keeps happening!  If I have the leader in the projects window and the timeline (or just the projects window) it's starts to freeze and behave like this.
    I'm not sure if it's only isolated to the universal counting leader, but if I delete it from my project, save and reopen, everything runs smoothly!
    Anybody have this issue or know why this is happening since the update?
    Thanks.

    Hey all,
    I posted in here a while back because I was working with MTS files and seemed to be having an issue out of the blue with my projects freezing, where the video would play, but the cursor and anything I would click or move would not respond.
    I ended up transcoding to Prores and finished the edit. 
    BUT!!!  Even in the prores version this happened again, and I finally tied it to the universal counting leader.  Now I've used this thing many times before with no problems.  But since the most recent update (I'm now running CC v8.1.0) this keeps happening!  If I have the leader in the projects window and the timeline (or just the projects window) it's starts to freeze and behave like this.
    I'm not sure if it's only isolated to the universal counting leader, but if I delete it from my project, save and reopen, everything runs smoothly!
    Anybody have this issue or know why this is happening since the update?
    Thanks.

  • Games keep crashing since recent updates

    Hey there,
    I've had no problems before with playing games (mostly via Steam), however, since recent OS X updates I'm lucky if I can get more than 2 minutes of game time in before the game decides to freeze or crash.
    Here's my EtreCheck report - any ideas how to fix it?
    EtreCheck version: 2.1.8 (121)
    Report generated 7 April 2015 23:15:13 BST
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Click for support] links for help with non-Apple products.
    Click the [Click for details] links for more information about that line.
    Hardware Information: ℹ️
        iMac (27-inch, Late 2012) (Technical Specifications)
        iMac - model: iMac13,2
        1 2.9 GHz Intel Core i5 CPU: 4-core
        32 GB RAM Upgradeable
            BANK 0/DIMM0
                8 GB DDR3 1600 MHz ok
            BANK 1/DIMM0
                8 GB DDR3 1600 MHz ok
            BANK 0/DIMM1
                8 GB DDR3 1600 MHz ok
            BANK 1/DIMM1
                8 GB DDR3 1600 MHz ok
        Bluetooth: Good - Handoff/Airdrop2 supported
        Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
        NVIDIA GeForce GTX 660M - VRAM: 512 MB
            iMac 2560 x 1440
    System Software: ℹ️
        OS X 10.10.2 (14C1514) - Time since boot: 3 days 2:23:21
    Disk Information: ℹ️
        APPLE HDD ST1000DM003 disk0 : (1 TB)
            EFI (disk0s1) <not mounted> : 210 MB
            Macintosh HD (disk0s2) / : 999.35 GB (207.83 GB free)
            Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
    USB Information: ℹ️
        Hewlett-Packard HP USB Mass Storage Device
        Apple Inc. FaceTime HD Camera (Built-in)
        Apple Inc. BRCM20702 Hub
            Apple Inc. Bluetooth USB Host Controller
    Thunderbolt Information: ℹ️
        Apple Inc. thunderbolt_bus
    Gatekeeper: ℹ️
        Mac App Store and identified developers
    Kernel Extensions: ℹ️
            /Library/Extensions
        [not loaded]    com.mice.driver.Wireless360Controller (1.0.0d14 - SDK 10.9) [Click for support]
        [not loaded]    com.mice.driver.WirelessGamingReceiver (1.0.0d14 - SDK 10.9) [Click for support]
            /System/Library/Extensions
        [not loaded]    com.mice.driver.Xbox360Controller (1.0.0d14 - SDK 10.9) [Click for support]
        [loaded]    com.nvidia.CUDA (1.1.0) [Click for support]
    Launch Agents: ℹ️
        [not loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
        [running]    com.adobe.AdobeCreativeCloud.plist [Click for support]
        [loaded]    com.google.keystone.agent.plist [Click for support]
        [not loaded]    com.nvidia.CUDASoftwareUpdate.plist [Click for support]
        [running]    com.rosettastone.rosettastonedaemon.plist [Click for support]
        [running]    com.trusteer.rapport.rapportd.plist [Click for support]
        [loaded]    org.macosforge.xquartz.startx.plist [Click for support]
    Launch Daemons: ℹ️
        [running]    com.adobe.adobeupdatedaemon.plist [Click for support]
        [loaded]    com.adobe.fpsaud.plist [Click for support]
        [loaded]    com.ea.origin.ESHelper.plist [Click for support]
        [loaded]    com.google.keystone.daemon.plist [Click for support]
        [running]    com.mice.360Daemon.plist [Click for support]
        [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
        [not loaded]    com.nvidia.cuda.launcher.plist [Click for support]
        [running]    com.trusteer.rooks.rooksd.plist [Click for support]
        [loaded]    org.macosforge.xquartz.privileged_startx.plist [Click for support]
    User Launch Agents: ℹ️
        [loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
        [loaded]    com.adobe.ARM.[...].plist [Click for support]
        [running]    com.akamai.single-user-client.plist [Click for support]
        [running]    com.amazon.music.plist [Click for support]
        [running]    com.spotify.webhelper.plist [Click for support]
        [loaded]    com.valvesoftware.steamclean.plist [Click for support]
    User Login Items: ℹ️
        iTunesHelper    Application  (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
        Dropbox    Application  (/Applications/Dropbox.app)
        Origin    Application  (/Applications/Origin.app)
        AdobeResourceSynchronizer    Application Hidden (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
        Google Chrome    Application Hidden (/Applications/Google Chrome.app)
        BetterSnapTool    Application  (/Applications/BetterSnapTool.app)
    Internet Plug-ins: ℹ️
        o1dbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
        Unity Web Player: Version: UnityPlayer version 4.3.4f1 - SDK 10.6 [Click for support]
        Default Browser: Version: 600 - SDK 10.10
        AdobeAAMDetect: Version: AdobeAAMDetect 2.0.0.0 - SDK 10.7 [Click for support]
        FlashPlayer-10.6: Version: 17.0.0.134 - SDK 10.6 [Click for support]
        AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Click for support]
        Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Click for support]
        Flash Player: Version: 17.0.0.134 - SDK 10.6 [Click for support]
        QuickTime Plugin: Version: 7.7.3
        PepperFlashPlayer: Version: 17.0.0.134 - SDK 10.6 [Click for support]
        googletalkbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
        AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Click for support]
        SharePointBrowserPlugin: Version: 14.4.8 - SDK 10.6 [Click for support]
        JavaAppletPlugin: Version: 15.0.0 - SDK 10.10 Check version
    3rd Party Preference Panes: ℹ️
        Akamai NetSession Preferences  [Click for support]
        CUDA Preferences  [Click for support]
        Flash Player  [Click for support]
        Trusteer Endpoint Protection  [Click for support]
        XBox 360 Controllers  [Click for support]
    Time Machine: ℹ️
        Mobile backups: OFF
        Auto backup: YES
        Volumes being backed up:
            Macintosh HD: Disk size: 999.35 GB Disk used: 791.52 GB
        Destinations:
            Data [Network]
            Total size: 2.00 TB
            Total number of backups: 63
            Oldest backup: 2014-06-23 07:52:14 +0000
            Last backup: 2015-04-07 21:49:08 +0000
            Size of backup disk: Too small
                Backup size 2.00 TB < (Disk used 791.52 GB X 3)
    Top Processes by CPU: ℹ️
            16%    mds
             3%    WindowServer
             0%    fontd
             0%    systemstatsd
             0%    Google Chrome
    Top Processes by Memory: ℹ️
        790 MB    com.apple.WebKit.WebContent
        481 MB    softwareupdated
        447 MB    Mail
        378 MB    mds_stores
        206 MB    Google Chrome
    Virtual Memory Information: ℹ️
        20.36 GB    Free RAM
        10.67 GB    Active RAM
        1.11 GB    Inactive RAM
        2.21 GB    Wired RAM
        44.56 GB    Page-ins
        0 B    Page-outs
    Diagnostics Information: ℹ️
        Apr 7, 2015, 10:41:48 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/dreadout_2015-04-07-224148_[re dacted].crash
        Apr 7, 2015, 10:16:52 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Total War SHOGUN 2_2015-04-07-221652_[redacted].crash
        Apr 7, 2015, 10:13:51 PM    /Library/Logs/DiagnosticReports/Total War SHOGUN 2_2015-04-07-221351_[redacted].cpu_resource.diag [Click for details]
        Apr 7, 2015, 10:07:03 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/dreadout_2015-04-07-220703_[re dacted].crash
        Apr 7, 2015, 09:59:11 PM    /Library/Logs/DiagnosticReports/dreadout_2015-04-07-215911_[redacted].hang
        Apr 7, 2015, 09:52:10 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/dreadout_2015-04-07-215210_[re dacted].crash
        Apr 7, 2015, 09:50:02 PM    /Library/Logs/DiagnosticReports/dreadout_2015-04-07-215002_[redacted].hang
        Apr 6, 2015, 07:09:39 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Last.fm Scrobbler_2015-04-06-190939_[redacted].crash
        Apr 6, 2015, 07:03:58 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Last.fm Scrobbler_2015-04-06-190358_[redacted].crash

    Time since boot: 3 days 2:23:21
    I'd reboot to clear out some temp and cache files.
    Have you checked with the game developers to see if you've got the latest version that is compatible with Yosemite?

  • Time machine freezing mac since mavericks update

    Time machine is freezing up my mac since I updated to Mavericks. I was having issues with it so I just decided to reformat my time machine external drive. I can back up manually when I tell it to, but when left alone to do automatic back ups, I will come back to my mac and it is unresponsive, I see the time machine drive light flickering, and when I turn off that drive, the computer starts responding again.

    Interesting. I now have my external TM HD connected directly to my iMac through USB 2. All seems to be working properly now. Had the computer set to wake up last night at 12 and it did do a back up then. Also when I logged on and woke it from sleep this this AM it went into a back up. Could it still potentially be the HD or FW 800 cable? When I connected the FW 800 directly to the mac, it didn't improve anything, but that was one of the same cables I was using before. If I use FW I do have to daisy chain the drive to my other external iPhoto drive due to having only 1 FW 800 port on my mac.

  • Asset Generator broken since recent update to Photoshop CC

    With this latest update to Photoshop CC, the asset generator no longer seems to support having masks on a folder - asset will NOT generate if this is the case. Seems the only work-around is to clip everything down to a shape layer, which is highly awkward. Is this a bug? Can it please be fixed? This used to work just fine and has only been broken since the most recent update.

    My team is having the same issue.  I'd love to hear about a fix to this.

  • P6N Diamond New Problem: Second HDD Randomly Starts/Stops Since recent Update

    Howdy All,
    Continuing problems with the P5N Diamond.
    This one's new.
    Previously I had the same problem as many others with the cold boot issue. Somehow, someway, it just stopped: cold boot or not, one day it just started booting fine....go figure.
    However, I recently (about 3 weeks ago) did the MSI live update that included something or other pertaining to the E-SATA....support for it or something to that end. Although I don't use the E-SATA, I installed it thinking I might at some point and since installing it, I have discovered a new problem: my second drives (in RAID 0) just opens/closes randomly. It seems to mostly occur when operating demanding programs: gaming, watching a video, that sort of thing.
    Everytime it does this, it takes me to desktop and asks me what program I want to use to open the program......which when I do, is nothing more than my second (D drive) HDDs in RAID 0. I then get the yellow pop up message in the bottom toolbar from Windows saying it's experienced a write failure problem. It hasn't done any damage that I can tell and I've lost nothing, but being taken to desktop perpetually is a major issue. This problem is driving me absolutely up the wall. No sooner than I start to do something and wham.....I'm at desktop being asked what program I want to use to open up the second HDDs. I've also tried just leaving it open but to no avail: it just randomly continues to open and close.
    I have my O/S on the C drive and 2 more HDDs in RAID O for back up on ports 6 & 7. Since doing the MSI update that included the E-SATA whatever, this new problem almost prevents the computer from being usable: certainly nothing in gaming is possible along with anything that requires uninterruption.
    Here's my system:
    M/B: P6N Diamond
    CPU: E6850
    RAM: Corsair XMS PC-8500, 2 x 1 gig
    HDD: 1- WD 150 Raptor
    HDD: 2- WD 5000AAKS in Raid 0
    Vid Card: EVGA 8800GTX
    PSU: PC Power & Cooling 750 Silencer
    ODD: Sony DRU 830A
    FDD: Sony Floppy
    Misc: Scythe fans x 5
    O/S: XP Pro w/ SP2
    Running BIOS 1.2
    So, being fairly certain the MSI update created the problem, my question is, how do I undo the MSI's most recent update to remove it? When I go into Add/Remove Programs, nothing is listed there. I'm not sure this is the source of the problem but I do know I didn't have it beforehand.
    I'd greatly appreciate any help with this....even any ideas. While I have some computer knowledge, I'm not as tech savvy as most here, but this problem is, apart from driving me up a wall, making the computer almost unusable. FYI, I haven't done a System Restore because I've installed several things since and don't want to lose them if I can isolate the problem, but I will if that's what you all recommend.
    Again, sorry for what may be a noobish question, but I'm not sure where else to go. After dealing with MSI's tech support, I'd rather talk to a wall.
    Thanks greatly.
    Pepper1

    Mark,
    Forgive me for asking, but I am a bit confused. Is your "cold boot issue" now solved? If so, do you think that the new drives are the key?
    Lev
    Quote from: MarkJohnson on 17-December-07, 14:21:23
    Sorry for late post.
    After setting up the HW RAID (2500YS) for booting the system still cold boots.  strangely this time the reset (Ctrl+Alt+Del) doesn't seem to work.  I must of did it two dozen times and it would never clear.  I then just powered off after the other 2 drives on the nvidia SATA cleared and seen the HD LED light up and stay on for a few seconds(seems stuck on the 4723 checks of the drive) and then powered down and powered right back up with no cold boot issue.  It has worked this way every time for the last week or so and I tested it like 20 or so times(3-4 times a day).  These drives are listed as being compatible after the firmware update (and I did that already) so I guess it is either the MB BIOS needs updating or it's the way the nvidia chipset runs this setup is wacky.  This is assuming the 4723 HD compatibility list is correct.
    here's a summary of the drives so far.
    36GB Raptors (old revision) - can take forever to boot properly and corrupted my disk in 3 days of testing (scrambled my directory structure)
    105GB Raptors - Just reset(Ctrl+Alt+Del) 1-4 times after the HD LED goes solid for a few seconds.  worked for two months no errors.
    250GB Caviar RE(2500YS) - have to power off (power button) when HD LED goes solid.  so far no problems for a week.
    80 GB SATA II Hitachi Deskstar (HDS728080PLA380 - May 2005) - same as 150 GB Raptors, just a reset or four, only did a days worth of testing with no errors.
    well, I was hoping for those 2500YS to work properly.  Now it makes it really hard to track the problems with so many different errors and 3 different places it can go wrong 4723/nvidia/msi/HD Manufacturer.  wait, that's 4.  Oh boy!
    Hopefully this gets resolved soon.  I've already had to move this MB to my secondary system, and for other reasons than this.  I didn't mind hitting the reset button to get this to run.  I get the feeling that MSI has abandoned this board on us.  with the new P7N being released it will be even harder to get anyone to mess with this thing.
    -=Mark=-

  • Mail Signatures behaving strangely since recent update to 10.5.5

    Hi there
    Some, but not all, of our macs have started to behave a little bit strangely since updating to 10.5.5
    We use Apple Mail 3.5, we all have a set default signature which we sometime have to change depending on the circumstances. Prior to the recent updates all machines behaved in the same way. When creating a new mail the default signature appears, when you select a new signature the default one is replaced.
    The new behaviour on some of the machines is that the new signature is added below the default one.
    I would like all of the machines to replace the default signature.
    Any ideas?
    thanks for your help.
    Curtis

    Hi there
    Some, but not all, of our macs have started to behave a little bit strangely since updating to 10.5.5
    We use Apple Mail 3.5, we all have a set default signature which we sometime have to change depending on the circumstances. Prior to the recent updates all machines behaved in the same way. When creating a new mail the default signature appears, when you select a new signature the default one is replaced.
    The new behaviour on some of the machines is that the new signature is added below the default one.
    I would like all of the machines to replace the default signature.
    Any ideas?
    thanks for your help.
    Curtis

  • Streaming Movies and TV Shows from iTunes is very, very slow since recent update

    I have an Apple TV 2nd generation and since I updated it to the latest firmware available, that came out last week with the announcement of a new Apple TV, streaming content from iTunes servers, Movies and TV Shows, has become a nightmare. I don't think it is due to the firmaware update as I think it is due to the lack of capacity of the servers. As recent as last week everything worked fine. I would just press play and the TV Show would start almost immediatly and the streaming was fast enough that all the TV Show, past the point I was watching, was downloaded, without any delay or having to stop to rebuffer. The first time I noticed it was on monday this week and since then I have been testing streaming directly from iTunes every now and then and it never came back to work the way it did. I know the problem isn't my network. I have a 20 Mbits connection and download content at 2 Mbytes/sec on avarage.
    And I don't know if it has something to do with the fact that Apple has made available content in 1080p, and that maybe it is stressing its servers even more. What I do know is that the way it is working right now undermine the entire concept of what Apple TV should be like. It has to work just the way it did when Eddy Cue gave a demonstration of the new Apple TV on Wednesday, the content played authenticated immediatly and started playing, without long time buffering. "People are going to love streaming movies and TV shows in 1080p with the new Apple TV", said Philip Schiller. But I can't even stream 720p content.

    I am also experiencing intermittent streaming from the cloud with 1080p content. My internet package is pretty decent with 25MB and when I download a show on iTunes, it shows a download speed of 22MB so all is well with my connection to apple. The only way I can stream content without any interruptions is to change the settings on the AppleTV3 to 720p.
    I called my ISP and applied for a 50MB package and see it it helps.

  • Lots of problems since recent updates

    Since the most recent updates for Mavericks and iTunes, I am having a host of problems with iTunes, and am losing my patience.  If anyone can help, I would certainly appreciate it.
    I have a rather large library, stored on an external drive, which I have not had problems with in the past, and this same drive holds files other than iTunes related items.  iTunes has 'lost' my library twice recently, forcing me to go through great lengths to get it restored, including spending the past several days literally adding everything back into it.  This morning, it did it again. After restarting my computer, iTunes, once again, came up with the message that it cannot find my library, in the very place it has been, and where it was accessing it 2 minutes earlier.  The itunes library files are still there, nothing has changed, and this is now the third time it's done this since updating.
    I have followed all of the recommended steps to restore the library, none of which has worked properly.
    Right before restarting the computer, while I was finishing up Re-importing the last of my movies, iTunes stopped importing them.  No error message, just I would drag and drop the files (these are the same movies I've had in my library and have been watching, some for years), and I got no response. Then, I tried 'Import to Library' rather than dragging, and got the same.  So, I closed out, and restarted, leading me to yet another lost library.  To start from scratch, to give you an idea, I have 500+ gigs of music, and several hundred movies/tv shows.  I am not happy thinking that I will have to do that again.
    When iTunes opens, and gives me the message that it cannot find its own library, I choose to select a library and send it back to the same spot I've been using.  The library files are all still there, and yet iTunes claims not to see them, telling me there is no library file in this location.  I am incredibly fristrated right now.
    Please help?

    Verizon Wireless Customer Support wrote:
        I truly understand your viewpoint MySIII. Software is definitely suppose to enhance your phone and not hinder it. Your right, our customers should not have to worry each time an update is released. I'm sorry you are having so many issues with your phone. Our suggestion to uninstall and remove apps is just to give the new update a chance to make your phone better. This works the same for apps and functionalities that were not put on your phone when released. Now that your phone is working differently other functionalities have an opportunity to work or become better. We also suggest a factory reset after large updates. Please ensure your phone information and contacts are backed up. Here are the steps http://tiny.cc/7unvuw . Please let me know if the above information helps.
    KinquanaH_VZW
    All I hear is Blah blah blah..First of all, I am not gonna do a factory reset, (and I know all about backing up everything).  And so now you are saying that every time we get an update, we have to factory reset or uninstall all of our app and reinstall??  That is utterly ridiculous...
    This Issue is NOT an app issues or a factory reset issue. Are you no reading me , or any other threads or posts about this?   The update was a keyboard and camera update, so take you VZW clout and let the people that need to know, that this update sucks and they need to FIX IT...Period. No factory resets, no app uninstall and reinstalls..This is a Samsung keyboard issue (and for some reason battery draining)  The Samsung stock keyboard is not app related.  .None of those suggestions work.. OK.  Just fix the update.  So no, the above info does not help. Thanks tho.

  • Cannot print a web page since recent update to Apple Snow Leopard

    After recent update to Mac OS 10.6.4 I cannot print any page when using Firefox. I tried using Apple Safari and there was no problem
    == This happened ==
    Every time Firefox opened
    == After recent update to Mac OS 10.6.4

    This is a Firefox printing issue that I just fixed for my 85 year old Mom (birthday present). Other people have the same problem so I'm posting the solution:
    Go to address bar in Firefox--
    Type in this:
    about:config'''
    Click I AGREE on the warning
    Find -- '''print.macosx.pagesetup-2'''
    '''RIGHT CLICK on your mouse'''
    and go to '''RESET'''

  • Paid membership for Muse no longer works since recent update

    I have a paid membership for Adobe Muse, but after a recent update Adobe only allows me access Muse through a 30-day free trial. I am occasionally requested to enter a serial number for Muse, but cannot find any reference to this in my past emails. How can I overcome this ongoing issue?

    Hi,
    Please try the steps below depending on the operating system,
    Windows
    Click on the "Start" menu. Select "All Programs" and then "Accessories"
    Right-click on "Notepad" and select "Run as Administrator"
    Click "Continue" on the "Windows needs your permission" dialog
    When Notepad opens, click File and select Open
    In the filename field type the following:C:\Windows\System32\Drivers\etc\hosts
    If any entries in the host file include keywords such as "adobe," delete those entries. These are used for Adobe Licensing.
    From the "File" menu select "Save" after making changes
    Restart Muse
    Macintosh
    Click on the "Finder" icon. Select the "Applications" folder
    Open the "Utilities" folder and select "Terminal"
    Type the following:sudo nano /etc/hosts
    Enter the OS user's associated password when prompted
    If any entries in the host file include keywords such as "adobe," delete those entries. These are used for Adobe Licensing.
    Press control+o to save the file
    Press control+x to close the file
    Restart Muse
    Please let me know if it works.

  • Imnot sure if I am in the right please for this..I have OSX 10.9 ..I produce  weekly invoice in numbers which I export to Exel . Since recent updates I find that the file extn is now XLSX and when I open it the cumber content has changed! Can anyone help

    I use 'numbers" to create an invoice which I previously exported(prior to recent updating) to Exel to enable me to send it to my employer. When I try to do this now I get an file extn XLSX and the number content I placed on the invoice is different ( as if the file is corrupted)...can anyone help please ?

    I use 'numbers" to create an invoice which I previously exported(prior to recent updating) to Exel to enable me to send it to my employer. When I try to do this now I get an file extn XLSX and the number content I placed on the invoice is different ( as if the file is corrupted)...can anyone help please ?

Maybe you are looking for