Fresh installation of 2012r2 on PowerEdge r620 rebooting every 10 minutes

Installed 2012r2 Standard Evaluation on a Dell PowerEdge r620 today. In response to a failing 2003 DC. It's rebooting every 10 minutes or so with an lsass error.
A critical system process, C:\Windows\system32\lsass.exe, failed with status code c0000005.  The machine must now be restarted.
I'm doubly concerned as in the process I raised the forest level from 2000 to 2003 (We still have 2 2003 DCs, one of them the struggling one) I've promoted it to DC and transferred the FSMO already. I've got the weekend to get it sorted...
It's my first server install and I just did a straight bare metal install without installing Dell drivers. I'm thinking this may be my problem...
Any advice greatly appreciated.
Neil

After reading so much about the irreversibility of raising the forest level once offline DCs have been added again I was cautious about adding the previously downed DR DC. However the FSMO roles and AD replication were struggling so, after some consideration,
I brought the offending DC back online (AD has not been actively maintained for more than a couple of years...)
Initial signs were good. Replication was happening. 
However, my process involved replicating across to the new server data from more than one source (The org had suffered from server spread over the past few years). In the process of consolidating the DFSR namespaces and shares, and removing legacy FSR replication
I hit problems with deleted namespaces and replication groups lingering and not being able to be deleted. I tried to follow various diagnostic and recovery methods. See this post. My main concerns continue there... :-
Bah. Can't post link. Account not verified yet. Will edit in due course. Check my profile for the DFSR related thread...
Not wishing to jinx it but the AD looks fairly stable now. Slight concern is repeated system log entries indicating :-
The DFS Namespaces service has successfully initialized the shared folder that hosts the namespace root. Shared folder: *********
Would be great to get rid of them.

Similar Messages

  • IPad2 reboots every few minutes

    My iPad2 recently began to reboot every few minutes of use.  It has been reformatted, all added apps removed and the battery allowed to completely deplete then recharge, all to no avail.  Any suggestions?

    If you are near an Apple Store, a trip to the Genius Bar.  If you are still under warranty they can replace it.  If you are out of warranty, they may still be able to replace it for a fee but it will still be less than full retail cost.

  • WRT54G reboots every 20 minutes

    I recently just switched from astound to comcast and astound worked fine 100% uptime no d/cs or anything...When we switched to comcast the router reboots every 20 minutes. I called comcast and they said everything is fine on their end. I tried power cycling everything and still no luck. When i connect directly to the modem I get no d/cs. Anyone have any ideas? Thanks in advance for any possible help, and sorry for my prolly horrible grammar. =]
    Message Edited by Hukepi on 08-08-2007 10:31 PM

    hi... connect the computer directly to the modem, go to www.linksys.com/download and download the latest firmware for the router, connect modem >> router >> pc, logon to router's setup page, open I.E. and in the address bar type 192.168.1.1 it would ask for username and password...put "admin" (default password) as a password and try reflashing/upgrading firmware on the router, after reflashing firmware on the router reset it and reconfigure it according to ISP settings and try reducing MTU to 1365 on the router...check whether it makes any difference or not and let me know the results.

  • My iphone4s keeps rebooting every 3 minutes; what might be wrong

    My iphone 4s keeps rebooting every 3 minutes; what might be wrong

    Welcome to the Apple Community.
    Check that the HDMI cable is seated correctly at each end and try another cable if the problem persists.

  • WRT400n reboots every few minutes

    HI,  I have this router and was working great......  THEN I get this great idea,  oh yeh, check to see if there is a firmware upgrade and there is.  Well I updated it with the newest and only one out there.   I did the upgrade, said sucessful and now it will just random reboot or something........ every few minutes the power light starts flashing....... then all the light go out, then power flashes again and it comes back up.   I have tried many times to reflash it with that new firmware but no avail.  I wish I had the old firmware back because it was working fine till I did this upgrade.   Anyone or Cisco persons have a solution for me,  can I get a copy of the original firmware or what is going on.    I am about ready to switch brands.... I've been a loyal Linksys/Cisco guy for long time but this and couple other routers I worked on are getting me to wonder.  Please help.......... thanks.

    Yeh I have done a hard reset numerous times....  I have re-flashed it 3 times.   I just did flashed it again, and did a hard reset and setup my router settings the way I want it.  I will see what happens overnight and repost my solutions.  My guess is it will start acting up again...... I've tried everything.    Does anyone know where I can get the original flash file for the WRT400n,  it was working fine till I tried to update with the latest one.....  should have left it alone.  If I can't fix it....... I am switching brands.

  • While charging my new 9320 it keeps rebooting every few minutes

    I upgraded to a BB Curve 9320.  Today it is charging for the first time, but while charging it keeps rebooting, not continually but every few minutes.  I already connected it to my computer which has Windows 7, to the Blackberry software and synced it with Contacts etc, but it is still rebooting.  Anyone know what's wrong?

    Hi and Welcome to the Community!
    So, it only does this while charging, and only while charging on the wall charger? What about just charging to the PC? Or to a car charger? What about different wall/car chargers than those you already have?
    In any event it is possible that your battery may be defective...to test, this sequence is needed:
    Obtain a known good and already fully charged additional battery...use it in your BB and see what happens
    Obtain access to a known good and identical BB...use your battery in it and see what happens
    The results of this will indicate if it's your BB or your battery that has the problem.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • How to stop my ipad shutting down and rebooting every few minutes

    My iPad G1 consistently closes down every few minutes and reboots even if just sitting idle on Home Page. How can I stop it PLEASE??????

    Try Recovery Mode per the instructions here.  If that doesn't help, you may well have a hardware problem.  Sorry.

  • Since dowloading Ios7, my ipad cannot connect to 3G and when I have no wireless or 3G connection, it closes down and reboots every 2 minutes or so. This happened in central Manchester and also on the Virgin Train from Man. to London. Totally unusable.

    Since downloading IOS 702 I cannot access 3G. Also when I have no access to wireless connection my ipad closes down and reboots every couple of minutes. I was trying to raed a book on a train from Manchester to Euston and had to give up. I found that auto-lock had defaulted to 2 minutes. I changed it to never but it made no difference.

        jsavage9621,
    It pains me to hear about your experience with the Home Phone Connect.  This device usually works seamlessly and is a great alternative to a landline phone.  It sounds like we've done our fair share of work on your account here.  I'm going to go ahead and send you a Private Message so that we can access your account and review any open tickets for you.  I look forward to speaking with you.
    TrevorC_VZW
    Follow us on Twitter @VZWSupport

  • IPhone reboots every 15 minutes after iOS 6.1.2 upgrade

    "Reboots" is the best way to describe it. Every 15 minutes or so, my iPhone suddenly goes to the Apple logo over black and back to my passcode screen (though doesn't stay on the logo as long as during a manual reboot). Doesn't matter if the phone is sleeping or being used. This started happening after I updated to 6.1.2 directly on the phone. Unfortuantely, I didn't do a manual back-up before updating as I've been relying on automatic iCloud backups.
    Any advice?

    Standard troubleshooting...
    Try a reset by pressing the home and sleep buttons until you see the Apple logo, ignoring the red slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.
    Remove all apps from Recently Used list...
    - From any Home Screen, double tap the home button to bring up the Recents List
    - Tap and hold any icon in this list until they wiggle
    - Press the red  to delete apps from this list.
    - Press the home button twice when done.
    If still a problem restore with your backup.
    If still a problem restore as new, i.e. without your backup. See how it runs with nothing synced to it.
    If still a problem, it's likely a hardware issue.

  • 10.10.3 overloads CPU, overheats, freezes, reboots every 3 minutes

    The problem appears to be with the new Photos app.
    When I run it and look at the CPU usage, it's pegging at 200-250% usage.... shortly thereafter followed by the fan coming on, then the whole thing overheating, freezing, and hard rebooting.
    I think I have narrowed it down to the "upload to iCloud Photo Album" option in the preferences... every time I click the "pause for 24 hours" button, the CPU usage comes down to 140-180% range, and the fan slows down, delaying the overheating.
    Apple, please look at this....
    MBP 15"
    Early 2011
    16gb RAM
    250gb SSD

    Have the same problem. Fotos seems to generate thumbnails of every picture. But eventually it fills the syslog with messages like that:
    09.04.15 21:55:10,930 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:11,359 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:19,879 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:20,753 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:21,641 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:21,650 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:21,948 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:23,815 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:24,518 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:25,764 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:26,280 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:26,351 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:26,578 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:26,994 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)
    09.04.15 21:55:31,131 Photos[1069]: ImageIO: CreateMetadataFromXMPBufferInternal  Threw error #102 (Named children only allowed for schemas and structs)

  • K9AGM and Vista : Reboot every 10 minutes

    Vista Home Premium 32 bit installed fine on the K9AGM. The OS runs fine for precisely 10 minutes and then, it resets. There is no kernel trap (blue screen) but just a reset.
    -RAM have been tested extensively without problems
    -Reset occurs precisely after 10 minutes every time
    -CPU is a single core 3800+
    -During the first 10 minutes, Vista is working as expected
    -Power Management setting does not seem to have an effect on the problem
    -XP MCE 2005 runs without a hitch on this machine and therefore, it seems to be a Vista related issue only
    I still investigate the issue to identify the faulty setting or driver.
    Any help or additional information is appreciated.

    Here are some additional details.
    HARDWARE
    -Motherboard K9AGM-FID
    -AMD Athlon64 3800+ with AMD Fan/Heat sink
    -2x512MB Kingston ValueRAM KVR667D2N5K2
    -Seagate Baracuda 7200.10 300GB SATA II (ST3300622AS)
    -Antec NSK2400 case including Antec 380W PSU with following amperages:
     +5v:25A +12v:16A +3.3v:25A +5vSB:2A
    -Nothing else on the motherboard
    OTHER TESTS PERFORMED
    -Under both Vista safe modes (with and without networking), reset occurs after 10 minutes flat.
    -Every suspect option in BIOS has been tested.
    -Not related with screen saver.
    -Away mode disabled in Power Options.
    Has anybody sucessfully installed Vista on this motherboard?
    Any input greatly appreciated.

  • OS4 upgrade = error 29 then reboot every few min. on use

    Tried to upgrade my iphone to os4 last night and got an error 29 message and was then stuck in an endless reconnect to itunes loop. Restore only resulted in further error 29 messages. Finally after a good bit of searching on potential solutions I used irecovery to escape the loop. Now os4 is on my iphone (and looks great!) but it reboots every few minutes (2-3) when being used. It does not reboot if off. I tried restoring again after discovering the reboot problem but that got me back to square one and error 29 messages again.
    Noticed some others with similar issues but didn't see a thread with this exact problem posted.
    Perhaps it's worth noting that I replaced my iphone battery myself a few months ago but had no issues at all until now. Not a jailbroken iphone. Just trying to get it to work.

    mrrutter wrote:
    Tried to upgrade my iphone to os4 last night and got an error 29 message and was then stuck in an endless reconnect to itunes loop. Restore only resulted in further error 29 messages. Finally after a good bit of searching on potential solutions I used irecovery to escape the loop. Now os4 is on my iphone (and looks great!) but it reboots every few minutes (2-3) when being used. It does not reboot if off. I tried restoring again after discovering the reboot problem but that got me back to square one and error 29 messages again.
    Noticed some others with similar issues but didn't see a thread with this exact problem posted.
    Perhaps it's worth noting that I replaced my iphone battery myself a few months ago but had no issues at all until now. Not a jailbroken iphone. Just trying to get it to work.
    Ok. From reading through the forums some more it definitely seems to be related to the battery. Perhaps for some it's because they have a semi-bad original/OEM battery. For me I'm guessing it's because I installed a non-OEM battery when my original started to fail. I bought a higher capacity replacement than OEM off the internet thinking it would give me better battery life. It worked perfectly fine until upgrading iOS4. In addition to previous problems posted my battery is either not charging at all now or charging very slowly. It reboots even as I'm trying to recharge. I've turned it off while trying to recharge it now in the hopes that this will make it charge properly. I've also ordered an OEM battery now in the hopes this will fix the problem. Wish I hadn't discarded the original. Odd that an OS upgrade would cause this problem. The tinfoil hat part of me wonders if Apple did this on purpose to discourage DIY fixes. If so, that's really uncool of you, Apple. If I break my phone fixing it myself then let me break it. Please don't break it for me.
    Once I get an OEM battery and install it I will update on whether that worked for me or not.
    Here's a post from another thread concerning error 29:
    Hi all,
    I am so happy! I can confirm the error 29 has been resolved and it is to do with the battery gauge. I ordered a higher capacity battery from Ebay, that messed around with the readout in 3.1.3. I was on the verge on making a claim for a replacement iphone until just now. Also as a word of warning, Non apple OEM battery will cause the phone to crash. Maybe the phone is sensitive to calculating the gas gauge so when it can't work out the exact charge it'll force the phone to reboot every 5 minute interval, this is apples ploy to dig out illegal modifications? This is very interesting, Phone fully functional now after installing OEM battery. I will now install the bigger capacity battery to see if it is compatible with it. I'm guessing not.

  • Fresh Installation Boot Errors

    I'm new to trying to work with Solaris 10, and to a lot of Solaris in general, so while I'd normally be happy to do a lot of reading (and have tried searching for answers on google a good deal already), I'm having a problem after a fresh installation of Solaris 10 on a Sparc T3-1 server that I'm hoping someone can point me in the right direction to solve.
    During the install I told the text installer I wanted to do a ZFS installation using both of my disks (only 2) in a mirrored configuration. I selected the default set of core system packages.
    After the install seemed to be done and the system rebooted, I'm getting the following when it comes up:
    Boot device: /pci@400/pci@1/pci@0/pci@4/scsi@0/disk@w5000c5003a04f911,0:a File and args:
    SunOS Release 5.10 Version Generic_142909-17 64-bit
    Copyright (c) 1983, 2010, Oracle and/or its affiliates. All rights reserved.
    Failed to plumb IPv4 interface(s): igb0
    Jul 7 12:12:34 svc.startd[9]: svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96.
    Jul 7 12:12:34 svc.startd[9]: network/physical:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
    Hostname: tempdb
    Loading smf(5) service descriptions: 1/136
    WARNING: svccfg import /var/svc/manifest/application/management/sma.xml failed
    2/136
    WARNING: svccfg import /var/svc/manifest/application/management/wbem.xml failed
    3/136
    WARNING: svccfg import /var/svc/manifest/application/management/seaport.xml failed
    followed by another 133 lines with similar failures, followed by:
    svccfg import warnings. See /var/svc/log/system-manifest-import:default.log .
    WARNING: svccfg apply /var/svc/profile/generic.xml failed
    WARNING: svccfg apply /var/svc/profile/platform.xml failed
    Requesting System Maintenance Mode
    (See /lib/svc/share/README for more information.)
    Console login service(s) cannot run
    Root password for system maintenance (control-d to bypass): Reading ZFS config: done.
    Mounting ZFS filesystems: (6/6)
    After doing a new install off of the install media (cd) I would have expected the system to be able to boot without errors, but obviously I've missed something or done something wrong, and I'm hoping that someone can point me in the right direction for figuring out what that is and fixing it.
    I'm happy to provide any other details if there are questions.

    I do see a few messages in the installation log that give me concern. The first is:
    *Creating and checking file systems
    - Creating rpool/ROOT/rdata dataset
    - Creating dataset rpool/ROOT/rdata/var
    libshare SMF initialization problem: entity not found
    libshare SMF initialization problem: entity not found*
    There are also quite a few instances where a PKG installation says something like this:
    *Installation of <SUNWcnetr> was successful.
    pkgadd: ERROR: PKG parameter is not defined in <þëØ>
    346 blocks*
    or
    *Installation of <SUNWj5dvx> was successful.
    pkgadd: ERROR: PKG parameter is not defined in <þëØ>
    pkgadd: ERROR: PKG parameter is not defined in <þëØ>
    7153 blocks
    pkgadd: ERROR: class action script did not complete successfully
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/75dpi/fonts.dir> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/F3bitmaps/fonts.dir> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/Type1/fonts.dir> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/misc/fonts.dir>failed
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/F3bitmaps/fonts.dir> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/Type1/fonts.dir> failed
    pathname does not exist
    ailed
    pathname does not exist
    pkgadd: ERROR: class action script did not complete successfully
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/75dpi/fonts.alias.all> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/F3bitmaps/fonts.alias.all> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/Type1/fonts.alias.all> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/X11/fonts/misc/fonts.alias.all> failed
    pathname does not exist
    Installation of <SUNWaspell-en-share> was successful.
    14501 blocks
    pkgadd: ERROR: class action script did not complete successfully
    ERROR: attribute verification of </a/usr/openwin/lib/locale/ja/X11/fonts/75dpi/fonts.dir> failed
    pathname does not exist
    ERROR: attribute verification of </a/usr/openwin/lib/locale/ja/X11/fonts/TTbitmaps/fonts.dir> failed
    pathname does not exist
    Can't open ./fonts.dir
    Can't open ./fonts.dir*
    There are also a few that say:
    Reboot client to install driver.
    The installer did seem to reboot at the end. Does the installer handle those 'reboot client' cases itself?

  • ORA-27102 IN FRESH INSTALLATION

    Hi Forum
    I have a problem with the fresh installation my environment is:
    Solaris10 and Oracle DB10g R2 and the box have 4Gb RAM
    The installation can`t continue and stop in the Database creation 2% with the error message ora-27102, the manual quick installation say:
    ==========================================================
    On Solaris 10, use the following procedure to view the current value specified for resource controls, and to change them if necessary:
    To view the current values of the resource control, enter the following commands:
    # id -p // to verify the project id
    uid=0(root) gid=0(root) projid=1 (user.root)
    # prctl -n project.max-shm-memory -i project user.root
    # prctl -n project.max-sem-ids -i project user.root
    If you must change any of the current values, then:
    To modify the value of max-shm-memory to 6 GB:
    # prctl -n project.max-shm-memory -v 6gb -r -i project user.root
    ==================================================
    But when I change the shm-memory and reboot the box, the value is the same default 998MB.
    Please could anybody help me to resolve this problem
    Thanks and regards,
    Wilson

    Please, could anybody know about this issue??

  • [SOLVED] Several problems after fresh installation

    Hi guys,
    i just did a fresh installation of arch and every times i must do something i get this error:
    cannot remove, read, edit and etc : read-only file system
    So i searched for a workaround.. but i must do this after every boot
    This is it:
    mount -oremount,rw /
    There's a way to fix this forever?
    Often when i need to edit some files, like /etc/pacman.conf or xorg config file, arch tell me: You do not have write permission to modify... that file
    Searched another workaround.. and also this i must do every time after each boot:
    sudo chown -R black /directory of file that i'm trying to edit/
    I hope to fix this annoying problems, with your help.
    Thanks guys,
    Gabriele.
    Last edited by Lilith (2012-09-28 13:18:46)

    Ok guys,
    think solved by change my /sda6/ (root) by /mnt to / and adding a slash / before home, boot, var.
    Rebooted and try to edit the same file /etc/fstab and no warnings
    Now is like this:
    # /etc/fstab: static file system information
    # <file system> <dir>     <type>     <options>                <dump>    <pass>
    tmpfs                    /tmp        tmps        nodev,nosuid             0                0
    #UUID=blablablabla
    /dev/sda6                  /             ext4                  rw,relatime           0   1
    #UUID=blablabla
    /dev/sda9                  /home            ext4                 rw,relatime            0   2
    #UUID=blablabla
    /dev/sda5                  /boot              ext2                 rw,relatime             0   2
    #UUID=blablabla
    /dev/sda7                  /var                 reiserfs            rw,relatime             0   2
    #UUID=blablabla
    /dev/sda8                  none              swap                defaults                  0   0
    Thanks to everyone i also fixed my 2nd problem that i think is related to the first
    Last edited by Lilith (2012-09-28 13:15:43)

Maybe you are looking for