From Azure unable to connect internal LAN network with windows RRAS site to site VPN

Hi All,
Below is my scenario.
Our side.
We have installed RRAS on Windows 2012 R2 on VMware and created a site to site VPN with azure.
on RRAS server we have two interfaces
eth0- 10.1.1.1
eth1- 10.1.1.2
We have natted(static nat) internal ip (eth0) 10.1.1.1 with public ip 1.1.1.1 (eg.).
On Azure,
We created a gateway, and two VMs.
VM1 = 11.11.11.1
VM2 = 11.11.11.2
Both VMs can ping each other.
VPN gateway on Azure and demand dial on RRAS server shows connected and, in and out data shows as well.
We can ping, tracert and rdp the RRAS server using both the interfaces IP [eth0- 10.1.1.1 , eth1- 10.1.1.2]
But we are unable to ping, tracert or rdp our other internal Lan machines on 10.1.x.x
So we can reach Azure VM from our RRAS and
we can reach RRAS server from Azure VM.
But we cannot reach our other internal Lan machines from Azure VM and from other internal Lan machine to Azure VM.
Please help?

I will give you some pointers to check.
The reason for this could be one of the two
- local site in azure virtual network is not configured correctly
- route for the azure subnet is not setup correctly on rras server
Can you please validate the above?
Open the Routing and Remote access UI and verify that there is a static route for azure subnet and the interface is the public ip of the azure gateway.
Also verify that you have a local site created with the on-premises subnet and added in the azure virtual network.
What is the gateway specified in the on-premises VM. Provide it as the IP of eth1, the IP that is not natted
Is NAT allowing all traffic in or is it restricted to certain points.
This posting is provided "AS IS" with no warranties, and confers no rights

Similar Messages

Windows 8.1: Unable to connect to IBSS network with a profile installed manually

I created an IBSS network, Imported the IBSS profile and trying to connect from my Windows 8.1 machine. It was not connecting to the network for some reason. Is it supported in Windows 8.1?
I was able to connect to the network from Windows 7 machine using same IBSS profile, But not with Windows 8.1. Is there any known issue related to this?

Hi,
Please take a look at the following articles regarding IBSS network:
Connection Operation Guidelines for Independent BSS Networks
Please note: IBSS (Ad hoc) and SoftAP are deprecated. Starting with Windows 8.1 and Windows Server 2012 R2, use Wi-Fi Direct.
Wi-Fi Direct Miniport Initialization and Configuration
Best regards
Michael Shao
TechNet Community Support

UNABLE TO CONNECT TO WIRELESS NETWORK WITH APPLE WINDOWS COMPUTERS CAN

I am new to Apple and am trying to connect to our at home wireless network.Have a Linksys wireless router that is functioning as far as I know correctly.We are able to connect with windows based laptops.My Apple sees our network which is identified correctly and asks for a password.When we enter the password that functions for the other computers it does not work.I s there a configuration change I need to make.Maybe a password variant? I really want to get this up and running and am out of ideas.
INTEL IMAC 20 IN 2.17 GHZ Mac OS X (10.4.7)

Are you using WEP, if you can try and use WPA.
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
AirPort: Joining an encrypted wireless network
http://docs.info.apple.com/article.html?artnum=106424
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WPA
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix

Unable to connect to LAN - Integrated 10/100BASE-T Ethernet LAN (RJ-45 connector)

Unable to connect to LAN, downgraded laptop from Windows 8 to Windows 7 64-bit. Have tried using the HP device identifier, and installing all drivers under Network for the laptop on WIndows 7, though none of them showed as being for Local Area Network.I also tried following this thread: http://h30434.www3.hp.com/t5/Wireless-Internet-Home-Networking/Integrated-10-100BASE-T-Ethernet-LAN-RJ-45-connector/td-p/4040756Downloaded the suggested drivers there for the HP Envy 17t-j100I also tested downloading the drivers here for Windows 7: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTypeID=3&GetDown=false Neither worked, I am still only able to connect via Wi-Fi, but not via LAN with actual cable attached.In case necessary, hardware ID for the Realtek PCIe FE Family Controller:
PCI\VEN_10EC&DEV_8136&SUBSYS_1854103C&REV_05PCI\VEN_10EC&DEV_8136&SUBSYS_1854103CPCI\VEN_10EC&DEV_8136&CC_020000PCI\VEN_10EC&DEV_8136&CC_0200

Hi: You can use all of the W7 x64 drivers and software from the HP 2000t-2a00 on your model except the BIOS and firmware files. Make sure you install the Intel chipset installation utility first and reboot before trying to install the Realtek LAN driver. http://h22207.www2.hp.com/us-en/drivers/selfservice/hp-2000-2a00-notebook-pc-series/5259212/model/5275371

Why can I connect to my home network with my iPhone 5 in one room, but when I move to another it is 'unable to connect to the network'

At home, I can connect my iPhone 5 to my home wifi network with no problems, as long as I stay downstairs.
As soon as I go upstairs my phone disconnects from the network. I can still see the home network it in the available network lists (with full signal strength), but when I try to reconnect I get an 'unable to connect to the network message'
If I move back downstairs it reconnects
This has only started happening in the past week or so
I've tried to forget and rejoin the network, but this doesn't work
I reset my network settings on the phone. This worked for a couple of hours and I could connect to the wifi upstairs, but now it won't connect again.
Does anyone have any ideas what is causing this?

Sounds like your wi-fi signal strength has degraded. Try rebooting your wi-fi router, or get it serviced.
Do you have similar issues with any other wi-fi routers?

Suddenly unable to connect to wireless network...exhausted all fixes

I’ve got an odd problem with my two-week old MacBook Pro and its connection to my wireless network. I’ve done what I think is pretty exhaustive troubleshooting, but remain baffled. Here’s the story.
This morning I connected to my wireless network (DSL 2WIRE modem/router) with no problem. This afternoon I returned and Airport refused to connect, giving me the error message, “Airport is unable to connect to the wireless network…” The network shows up as being available, but when I attempt to connect, it wont. (I didn’t make any changes or install any programs this morning).
Here’s what I’ve done:
[1] Restarted the router
[2] Repaired permissions
[3] Deleted the network’s entry in Keychain Access
[4] Re-entered my WEP code (assuring it is in correctly; I’ve tried both with the “$” and without)
[5] Used interface robustness and without.
[6] Attempted to join the network from the System Preferences>Network.Airport route.
[7] Created a new account and tried connecting.
Other tidbits of information:
[1] Another MacBook in the house connects to the network with no problem.
[2] My MacBook can connect to another (unsecured) network that I can “see” in my house.
So, it would seem my Airport card is working okay.
Any ideas??

Some more info (in case anyone is listening...)
I tried turning off the WEP code and could connect. (Since I share files on my home network, this isn't a "solution").
I also tried Resetting the MacBook Pro System Management Controller (SMC)(See: http://docs.info.apple.com/article.html?artnum=303319). I did this (I think -- there wasn't any indication that the reset "took"), but alas -- no luck.
I gave Apple Care a call, but the support guy, while courteous and all, didn't have anything to offer other than telling me to take it in to an Apple Store for a repair (clearly it isn't a hardware issue).
Heeellllppppp!

EthernetIP, Unable to connect to the network path specified, Multiple NICs

I have not been able to find an answer concerning this error, so I am hoping someone can help.
Computer has LabVIEW 2013 with the NI-Industrial Communications for EtherNet/IP 1.2.1 addon with Win XP although I have verified the same setup with Win 7 x32 with the same results. I am using the EthernetIP CIP Get Attribute Single.vi and the corresponding "Set" vi.
I am using a pc with five network cards, one for the corporate network (dhcp) and four that are connected to four Rockwell PowerFlex 700S AC variable drives via CAT6 crossover cables. Each 700S drive controls a motor in an engine dyno teststand. The 700S drives have the latest available firmware installed. The four NIC/700S pairs have hard coded IP addresses with the appropriate subnet masks for proper routing. I can use the Windows "ping" command without errors. The program uses a QSM-PC architecture which I have four separate qsm loops that "talk" to the each drive, those loops constantly request three parameters from the drive, a boolean drive status array, the rpm , and the torque every 250ms using the CIP "Get" vi. That data is then sent to the main front panel via shared variables. When the operator wants to say change the rpm, a write command is inserted into the queue, and the CIP "Set" vi is used.
My problem is when I start the program, it is hit or miss on whether these loops will begin to loop through their states. If they start, the program is rock solid. When one of the loops does not start, which is most of the time, the error returned is the "-251723767 Unable to connect to the network path specified". See the attached pictures. So if I disable three of the four loops, the error never shows up. Adding another loop or more will cause the error. Slowing down the request rate does not fix the issue and it is not always the same loop that will throw the error. Each qsm loop has its own session name and its own action engine with the only common thing amongst the action engines would be the "Get" and "Set" EthernetIP VIs.
No more ideas.....Kevin
Attachments:
error.PNG ‏12 KB
clone_error.PNG ‏30 KB

250 ms is a pretty slow update rate for CIP so Why use a nic for each drive? Use 1 drive nic in your PC and use a network switch to connect with your drives. If You have more then 1 nic you need to specify the nic to use for each loop for each drive IP address so the drive and the loops are using the correct IP settings. You should be able to use as low as 30 ms updates with no problems.

Message "WLAN: Unable to connect. Wlan Network not...

Well guys i bought my nokia 5800 today so like any other curious people i looked the wi-fi hoping connect with the internet and when i try to connect with the wi-fi appears this message "WLAN: Unable to connect. Wlan Network not Found." and then it dosen´t connectbut he finds normally the networ and this message appears after i type the Router password.i´ve already looked in another foruns and i´ve already switch off the Option Qos in my router and the problem cotinues, so anyone can help me?my router is one linksys wrt54g and the type of connection is static ip an the security is Wpa Personal TKIP....
PLEASE ANYONE CAN HELP ME?I´D BE VERY GRATEFUL WITH THE SOLUTION FOR MY PROBLEM...
Thanks
Message Edited by darkcraft on 13-Jul-2009 09:47 PM

tomasvaril wrote:
Same To me. I have Asus WL-500W router at home, WPA2-PSK(AES), password similar to this "lIGf@91pY0TnFY!Jh@7LjTUlsL3ZPY", MAC address filtering. My old Nokia E51 works, my Touch Pro Works with it. When i try my one day old Nokia E72 it does not work, the same like others:WLAN: Unable to connect. Wlan Network not Found. E72 works at my work wifi, which has the same settings but without mac filtering. Have no idea what is happening, all is setting correctly. MAC address of E72 is allowed on router. It has the same settings like E51, but E51 works like a charm E72 does not work. What is wrong?
As already suggested, you could try disabling the MAC filtering from the router, just to outrule possibility of a typo while entering E72's MAC address to router settings.
Have you tried swithing a WLAN channel that your router uses?
Log in to your router's web management pages (check router's default IP address and username/password from it's manual) and switch of the "Automatic" channel selection mode. Try few different channels, like 1, 3, 6, 9, 11, if one of the channels happens to work any better. Note that in case you have set your router to use channels 12 or 13 (or in case "Automatic" channel selection mode has decided to select channel 12 or 13) you must have a SIM card inserted and some other than "Offline" profile enabled on your phone since Offline mode (i.e. airplane / flight mode) won't allow your phone to operate on higher channels than 11.
In case you have configured your WLAN network (SSID) to be "hidden", try disabling hidden SSID mode on the router.
Asus WL-500W router seems to be a pre-standard 802.11n device so might be worth looking in to your router's WLAN settings and see if playing around with router's WLAN operating mode and settings improve the situation. First of all ensure that your router is not set to operate in 20/40MHz mode (set it to 20MHz only) assuming that the router is in default 802.11b/g/n mode. You could also try disabling the 802.11n mode completely by selecting a 802.11b/g mode (if available).
You should probably also check that you're running latest (2.0.0.6 ??) firmware version on your Asus WL-500W router since there seems to plenty of complaints regarding WLAN connectivity and stability issues (in general, not specific to Nokia handsets) with this particular router model.

Why isnt my itouch not connecting to the wifi? everytime i try to conncect to a network and then i put in the password, it says unable to connect to this network! why is not working?????????? someone please help me!!!

Why isnt my itouch not connecting to the wifi? everytime I try to connect to a network and i put in the password it says "unable to connect to this network" why isnt working?! the password is correct and everything. I just dont understand why its not working. Someone please help me! thanks

Did it ever work with this WiFi system?
Do other devices work with this WiFi system?

Unable to connect Wi-Fi network after ISO 6 update

unable to connect Wi-Fi network after ISO 6 update. I'm not impressed.

I updated to ISO 6 on my Daughters Iphone 4S, my Iphone 4, and I have now received my new Iphone 5 yesterday and now all 3 of them have wi-fi issues. I know its not my wi-fi because My Daughters Ipad 2 and my Wife's Iphone 4 is still on 5.11 and the wi-fi works fine. I cant understand why apple have not been saying what's going on and when they will fix it. I have tried everyone's suggestions on this forum and the Internet. Still no luck.

Unable to connect to my network at home

I am not sure as to how to set-up my connection to my network with the AirPort wireless system. What I'm I suppose to do to connect to my cisco network. Can someone please assist me in this matter

Is your Cisco device a WiFi router, or just a router?
I'll assume WiFi router.
Your home network should appear in the menu bar WiFi icon (a set of concentric arcs on the right side of the menu bar).
Select your Cisco WiFi router's name from the list.
If you are prompted for the password, then enter it. That should be all you need to do.
If your Cisco router is using WEP encryption, this can be a problem, as WEP has 2 different password encoding conventions, Microsoft's and Apple's. They are not compatible. ALso WEP is so insecure it can be cracked in less than a minute by easily available software.
Anyway, if your Cisco is configured with WEP encryption, then you need to enter the hexidecimal key, the text password will not work.
A better approach if you have WEP is to change the Cisco WiFi router to use WPA or WPA2 which has a standard password encoding method that is used by ALL WiFi devices, so you can then use the text password. In addtion WPA is very secure.
If none of this information works, or makes sense to you, we will need more information about your setup at home.

Unable to connect to Wi-Fi with password

Hello,
I'm having a slight issue with an iPod and iPad. As the title says, I'm unable to connect to wi-fi with password encryption (WPA2). I don't understand why! I can connect to wi-fi when I take the password encryption off. I've been able to connect to wi-fi previously with password encryption enabled. I live in a complex with three other neighbors. I'd prefer to not leave the encryption off. Does anyone have an idea as to how to solve this problem? I've already tried restatarting the iPod and restarting the wireless router. I tried to forget the network as well on both devices and reconnect them, however, when I try to reconnect them it tells me "unable to connect to the network". I do not wish to do a factory reset for either devices. Also, I'm unsure whether this is related or not, but I just updated my software recently to OS 6.1.2 ...my problem began a day after doing so.
Any feedback would be much appreciated! Thanks in advance. 8]
I have a Netgear WNDR3400 wireless router.

- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
I would try another encryption but still use encryption. Also try changing the PW.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.

I'm suddenly unable to join my Airport network with my PowerBook G4. I am able to access my network with all of my other devices. How can I once again establish access using my PowerBook G4.

I'm suddenly unable to join my Airport network with my PowerBook G4. I am able to access my network with all of my other devices. How can I once again establish access using my PowerBook G4?

Bruce777 solved this for me, thank you Bruce! My printer now works perfectly on my new wifi network!
Bruce's instructions, for anyone else having the same issue:
- delete any previously set up printers
- scrub old hp software and update software to get the hp 2.8 drivers
- remove the usb cable from the printer if you have one connected
- reset the printer network to hpsetup (hold down the power button and press network button 2x and then cancel 3x, release power button.)
- print out the wireless network test report (hold down the network button and press the update button 2x). verify the network name / ssid is hsetup
- got to sys prefs > network and change the mac wireless network to hpsetup
- go to the sys pref > print scan
- add the HP 8000 printer
- click on the options and supplies button and click on the Show Printer Webpage
- click on the networking tab > wireless in the left pane > start network wizard and change the network from hpsetup to your network
- finish (this page may freeze up. close the browser)
- go back to the sys prefs and change the wireless network back to your networt
- go to the printer and print out the wireless network test report (press network button and update button 2x). Check that the SSID is your network
- go to sys prefs > print scan > select your printer > options & supplies > show printer webpage > network info (check ssid and compare to wireless network test report)
- try printing something to your printer. It might take a little time the first print.

TS3274 Unable to connect to wi fi with mini IPad wi fi is working with other IPads?

Unable to connect to wi fi with mini iPad? All other iPads are able to connect. Not sure what to do?

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I have a RCA media streamer that will not connect to my network with a new airport extreme.

I have a RCA media streamer (Model # DSB872WR) that will not connect to my network with a new airport extreme.I had to create a new network and my computers are connected but media streamer will not. Can anyone help? Thank you

Hi, papineaubill!
Welcome to The Canon Forums, and thank you for your inquiry!
We appreciate your participation, though we need to let you know that the Canon Forum is hosted and moderated within the United States by Canon USA. We are only able to provide support for Canon products manufactured for and used within the US market. If you live outside the United States, please click here and select your country or region for your support needs.
Feel free to discuss Canon products sold outside of the United States, but please be aware that you will not receive support directly from Canon USA.
Thanks for choosing Canon!

From Azure unable to connect internal LAN network with windows RRAS site to site VPN

Similar Messages

Maybe you are looking for