From CANoe to LabVIEW

I have to send number from CANoe do LabVIEW by UDP (using the fdx protocol) and send back this number from LabVIEW to CANoe. It's my first time with CANoe and I don't know how to do this, how to make whole UDP frame. Is there anybody who can help me?

Dear poryta,
First of all, let me welcome you to the NI Forums,
I have searched our sources regarding your question and found some potentially useful information. Please read through these documents and let us know of the results!
Vectors' own Driver for CANoe x LabVIEW + Documentation:
http://vector.com/vi_labview_driver_en.html
Community (NI) Example:
https://decibel.ni.com/content/docs/DOC-16844
And I have included a Vector Document on How To Set up such a communication.
Good luck with your project,
Best regards,
Peter
Peter L.
National Instruments Hungary
Applications Engineer
Attachments:
CANoeLabVIEW_FastDataExchange.pdf ‏1723 KB

Similar Messages

Dll function calls from VB6 to Labview do not work.

HI,
We are transferring our production test systems from VB6 to Labview, and we are using "CAN-AC2-PCI" cards. When call functions of dll "canacpci.dll", UUT does not response at all, and Labview program does not report any error either. Attached are the user manual and my labview codes.
I guess the DeviceNe_init.vi works because if run it twice, second runing will report error. To correct the error, the card has to be closed first..
I close the card first, then initialize it. After then send the data. But I can not see any communication by DeviceNet Analyzer when sending data.
All function parameters are copied from existing VB6 program. The VB6 program works fine.
Please help me out,
Thanks,
Xiang Zhan
Attachments:
DeviceNe_init.vi ‏36 KB
DeviceNet_SendDataXXXX.vi ‏18 KB
CAN-ACx-PCI.pdf ‏139 KB

Hi Turck,
I'm not familar with this device, and it is difficult to say in this case. I would recommend calling into National Instruments support or contacting the vendor of the device for additional assistance in this case. As this isn't one of NI's Industrial Communications devices, you could also post on the LabVIEW forums for additional assistance, as there are a lot more people looking at that board than this one.
Thanks!
Matt S.
Industrial Communications Product Support Engineer
National Instruments

How can I call a LabVIEW executable from within another LabVIEW executable?

I have a customer requirement for two LabVIEW executables. Based on their current setup, they need to run executable "A" or "B", both of which are under independent revision control. I have created a third "selection" executable that allows the operator to choose between one of the two, but I am receiving errors when I attempt to call a LabVIEW executable from within a LabVIEW executable using either the "System exec" VI or the "Run Application" VI. If I call a non-LabVIEW executable (such as Windows Explorer) everything works fine.

> I have a customer requirement for two LabVIEW executables. Based on
> their current setup, they need to run executable "A" or "B", both of
> which are under independent revision control. I have created a third
> "selection" executable that allows the operator to choose between one
> of the two, but I am receiving errors when I attempt to call a LabVIEW
> executable from within a LabVIEW executable using either the "System
> exec" VI or the "Run Application" VI. If I call a non-LabVIEW
> executable (such as Windows Explorer) everything works fine.
As with the other poster, I suspect a path problem. You might try the
path out in a shell window, and if it works, copy the complete absolute
path to LV to see if that works. LV is basically passing the comma
nd to
the OS and doesn't even know what is in it, so you should be able to get
it to work.
The other poster commented on subpanels, which is a good suggestion, but
without going to LV7, an EXE can have open more than one VI. You can
use the VI Server and the Run method to fire up another top-level VI.
The decision is whether you want both to be in unique processes.
Greg McKaskle

3D Pie chart from Excel to labview

Hi every one,
How can I Import a 3D pie chart from Excel to labview ?
Thx

There is no direct import mechanism for that. You would need to re-create the pie chart in LabVIEW, as LabVIEW has different 3D graphs than Excel. You would need to get the data out of Excel and use the 3D graphs to draw it. As for getting the data out of Excel, there have been numerous posts on reading data from Excel using ActiveX - just search for "read excel labview". You can also find many links to lots of other examples in the Excel thread. Please note: the Excel thread is a repository of links. Do not post a question in that thread.

I can't connect to my PXI from within my LabView Project

Please advise,
I have been programming my PXI-8195 fine for weeks, but this morning I am receiving an error in connecting to the remote system from within my LabView Project. MAX says it is 'connected-running' and I even successfully tested a DAQmx task. I tried rebooting the PXI a couple of times as well as my host computer.
Thanks in advance for any assistance.

Hi Nik11,
What error are you receiving in LabVIEW? Also, what operating system are you using on the 8195, and are you using LabVIEW or LabVIEW RT?
Regards,
Adam W
Applications Engineering

Making dll from VI containing labview global variable ?

I've made dll from VI containing labview global variable.
But, when I write a c program calling a function from the dll, it returns just error.
The goal is to read a labview global variables from c program. What can i do for it ?

Hi
If you don't use the dll in your LV app, it will be difficult, because it will be in the adress-range of you c app. So any writing of values to the global variable in LV, won't affect the variable in the dll.
What you can do is some kind of client-server architecture. You need a third app, which just does the data exchange - so you should be able to write a value from LV and read it from c.
There already have been discussions about similar topics - just search the forum.
Thomas
Using LV8.0
Don't be afraid to rate a good answer...

How do I read the camera model and manufacturer from IMAQ in LabVIEW?

Hello All,
I have a machine vision application for automated test. I am required to save the image for each test for quality purposes. Since LabVIEW interfaces the CameraLink camera thru the IMAQ driver, various cameras can be used without changing the LabVIEW application. I need to store the basic configuration information, including camera model and manufacturer, with the image. I am able to read some parameters from IMAQ (like bit allocation and shutter speed) using the Read Attribute VI, but unable to read model and manufacturer.
Does anyone know how to read camera make/model from IMAQ in LabVIEW?

With this VI, any camera attribute that you can see and set in MAX, you should be able to see and set in LabVIEW. These are attributes that are defined in you camera file. Since Model/Make is not an "attribute" that you necessarily set, it is not included in your attributes tab in MAX.
If your camera file included a model attribute, then it would show up in MAX under attributes and you would be able to read it using the above-mentioned VI. The only thing I can suggest is perhaps use some File I/O instead of IMAQ VI's and read your camera file, if the ones you have are consistent in structure.
Hope this helps!
Tejinder Gill
National Instruments
Applications Engineer
Visit ni.com/gettingstarted for step-by-step help in setting up your system.

How can I have a csv file read from excel to labview.

Hi,
I would like to read multiple csv files from excel to labview, creating a duplicate of the tables in excel, which would allow me to then draw some graphs for data analysis and comparison between the two.
Are there any examples that could be useful to what I am trying to do?
Thanks

Patel33 wrote:
From one of the csv files, I only require 3 of the columns. Is there a way to only read that part of the csv file?
No. The characters in a file are just one long string and delimiters and linefeeds are special characters that defined where fields and lines start and end. As such, columns are interlaced into the file and consists of many small sections, where the position depends on the number of characters in each field, which is typically variable. You really need to read the entire file, then only look at the interesting columns later.
LabVIEW Champion . Do more with less code and in less time .

Migrated from VBAI to labview 8.2.

I’m fairly new at these vision programs and need some advise. I have migrated from VBAI to LabView 8.2. However I can’t seem to get the LV program to work like VBAI program works. The LV program gets stuck in a loop processing the same photo rather than the entire folder of 25. The other problems are: It will not show the photo; it will fail all photos, and will not log results.
I am running the LV 8.2, Vision Acquisition 8.2, and VBAI 3.0

Hi Davis,
I'm not experienced in VBAI and IMAQ, but in your code I couldn't find any function to load your JPG photos...
There's only an 'IMAQ Create' in the initialize-sequence, which generates an empty image. So it seems you have to attach your own code here ;-)
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Reading emails from gmail by labview

I easily found a sample program to send an email to Gmail in LabVIEW and it works well. But I want to read emails from Gmail in LabVIEW as well. Is this possible? Thanks
Jay
Solved!
Go to Solution.

Well, not so much a duplicate post, since that post was asking about reading attachments. This is asking about getting emails from Gmail.
To OP: Your question is not clear. Are you trying to download emails from your Gmail account? If so, you first need to configure Gmail to turn on the POP service. I don't think this is enabled by default. The Gmail help documents tell you how to do this. Once you've done that, you can just use a POP client. You can start by trying the one posted in this thread, but be aware, that sometimes servers have their own little "quirks", as alluded to in that thread.

How can i integrate canoe into labview?

I'm having trouble using canoe from labview.
I want to receive and send can-messages with a vector cancardx (pcmcia). Using the internet i found out, that this sort of thing is possible, but didn't find any tutorial or any hint on how to do this. Could someone please hint me to the right direction?
thnx in advance.
merlin

If you look in the back of the CANcard manual, you should see some info about interfacing to the CANcard driver DLL. You can then interface Labview to the DLL for the CANcard. I Don't know anything about interfacing to the CANoe program, but you probably will not be able to interface Labview to the CANcard at the same time as CANoe, because the CANcard can not be shared.

How can I convert a Database Handle from TestStand to LabVIEW?

I want to use a Database Handle (already created in TestStand by an Open Database step) in a LabVIEW-VI (called from TestStand) to connect it with the "Connection Reference" input of the "Easy SQL.vi"? If I use a directly connection via the "TestStand - Get Property Value (Number).vi" I get back the error message 4101 in LabVIEW. How can I convert the Database Handle?
Test Engineering
digades GmbH
www.digades.com

The TestStand database step types use the CVI SQL Toolkit to talk to databases. The handle that you are referencing is an internal memory location and not a actual handle that you can directly use. Currently as implemented the handle that is stored in a numeric TestStand property for the connection and the SQL statement are the handle values returned from the CVI SQL Toolkit. So for the connection handle, you could call the CVI SQL Toolkit function
DBGetConnectionAttribute (
int Connection_Handle,
tDBConnectionAttr Attribute,
void *Value);
and get the CVI CAObjHandle reference. With this you could then call the CVI ActiveX function
CA_GetInterfaceFromObjHandle(
CAObjHandle Object_Handle,
const IID *Interface_Id,
int Force_AddRef,
void *Inte
rface_Ptr,
int *Did_AddRef);
to get the actual ActiveX interface reference. This would have to be converted into a LabVIEW reference.
You may want to consider just using LabVIEW to open a new parallel reference only using the toolkit.
Scott Richardson
National Instruments

How to create a dll from vi in Labview 7.0 ?

Hello,
I want to create a dll from a vi in Labview 7.0.
I've found the url: http://zone.ni.com/devzone/conceptd.nsf/webmain/003A3E6A5E9CCCEC8625691F0072B2C5
explaining how to create DLLs from LabVIEW in Labview 6.0i but this method is not available in my Labview 7.0.
How is it possible to create a dll from a vi or from vi's (stored in llb-files) ?
With thanks,
best regards,
Geert

You can only create DLLs and Standalone Applications if you have LabVIEW professional or higher.
If you only have LabVIEW Base of Full, you need to purchase the Application builder seperately.
(Check under "Deployment tools" in the LabVIEW comparison matrix. What level do you have?)
Message Edited by altenbach on 10-18-2005 08:45 AM
LabVIEW Champion . Do more with less code and in less time .

Read image from excelsheet using labview

i need to know how to read image from excel sheet using Labview...m not able to get the appropriate property to display the image stored in excel sheet.
thank you

you need to ask Microsoft to find out the property name/location under Microsoft Excel.

How a variable in C++ gets updated from calling a labview dll running in a loop?

Hi,
I have created a dll which is called from a C++ program. The dll has been created from a vi which continuously runs in a loop (this is necessary because I need to control some hardware in real-time). When I call the function from C++ I can see the front panel of the vi working properly, i.e. all variables are updated in real time on the labview panel (which I will set as not visible once i get this problem sorted out).
However, I can't get the variables' values getting updated in my C++ program and I need these values to change in which way the hardware should behave ... is there any example somewhere in which something similar has been done? I have seen some examples where a dll is called from C++ with a vi function but not running in a loop. In these examples, the vi function passes the datum to the C++ software once is finished ...
thanks very much for your help,
kind regards
Sergio

Hi smercurio_fc!
Thanks very much for your answer!
I have already an inter-process communication, where there are two threads running in parallel. In one thread the C++ code is running while in the other the LabVIEW code is running. The labview function is passing the "output" variables as pointers too.
_1DScan(ReqForce,&StopAlign,0,&ReadForce,&Piezo_running,&RS232OK,&Running);
the function is called using the following:
void CFMControl::FMThreadProc()
_1DScan(ReqForce,&StopAlign,0,&ReadForce,&Piezo_running,&RS232OK,&Running);
return;
When I run the C++ code I can see both threads working by seeing data being updated in C++ front panel (data that belongs to C++) and in labview fron panel (data that belongs to labview). However, when I try to use any of the outputs coming from labview I can't get them updated....

From CANoe to LabVIEW

Similar Messages

Maybe you are looking for