From where in the UMI flex 6c I should give enable to servo motor amplifier/​driver.

I am using ADS 50/5 maxon amplifier to run the maxon servo motors with Flex 6C. The problem I am facing is that, How to enable the amplifier so that it works only when desired. I have tried by connecting the enable to the inhibit output but it is not working. before connecting to enable Inhibit output is showing 5v but as soon as I connect it , it drops to 1.5V. I am giving encoder feedback to 6C. Motor runs when I directly connect enable to the power supply, but then it runs continuously. Can anybody suggest me about the correct connections.
regards
vkmehta

If the output voltage of the inhibit output drops to around 1.5V as soon as you connect it to the enable input of your servo amplifier you should check the specifications for the enable input of the amplifier. It seems that an optocoupler is used, and if you apply 5V without any series resistance to the input led of an optocoupler the input voltage will be clamped between 1.5 and 2V. Also, the optocoupler may get damaged due to excessive current on the input led.
Check the manufacturers specifications for correct input wiring. In most cases a series (current limiting) resistor is needed, somewhere around 470 ohms.
You should also check whether you are applying the correct logic level to the enable input. Some servo amplifiers need a logic 1 (= 5V) on t
he input, some require a logic 0 (= 0V) to shut down the amplifier.

Similar Messages

  • TS4162 I have been able to upload videos to vimeo from FCPX in the past. However, now FC gives me a message that my password is incorrect. This is despite the fact that my password allows me to sign into the Vimeo website. Any ideas?

    I have been able to upload videos to vimeo from FCPX in the past. However, now FC gives me a message that my password is incorrect. This is despite the fact that my password allows me to sign into the Vimeo website. I have reset my vimeo password, restarted final cut and restarted my computer. Any ideas?

    Log in to Vimeo and change your password on the Vimeo site. Then update your FCPX settings for Vimeo to reflect the new password.
    I think Vimeo required this in light of the Heartbleed hack.

  • From where does the payment terms being determined while payment run.

    Hello Friends,
    When we run payment proposal, where did the system pick the payment term to determine if the vendor is due for payment? Did the system pick from the vendor masterdata or from Purchase Order?
    Please help.
    Thanks
    Mercy

    Dear,
    For any due date determination system always check into the document not the master data........if somehow payment term is not into document then system will not further look into master data but it will ignore the line item..
    Regards,
    Chintan Joshi

  • Unable  to  found from where does the Plan values are coming

    Hi Gurus,
    I am running the report Z_ALR_87012993 and getting values for Actual and Plan,
    i want to know from where does these planned values are getting into account and where to see that planned amount for that cost element (order).
    Regards,
    Imran M Arab

    Thank You All,
    My problem solved,
    I  found the T-Code for that is KOC4, in this we can see the planned values for production orders.
    Thanks again for your valuable replies.
    Regards,
    Imran M Arab

  • My phone was taken from me off the Edge and they won't give it back!

    Back in September of 2013 I bought in to the Edge program when I was told I could cancel the line AND the phone at any time.  I was told that I could return the phone AT ANY TIME (not just within the 14days) and everything would be cancelled.  On March 10th I went into a corporate store and cancelled the line and returned the phone.  The sales rep even analyzed the phone to make sure it was in good condition so he could cancel the edge contract.  By the way the phone was an HTC one.  So he told me I would see a charge on my phone bill for 24.99 every month but that I would also see a credit for 24.99 for several months until the contract ran out.  I said ok.  He took my phone.  They seemed confused - he was asking the store manager for assistance.  So 2 days later I call customer service to verify that everything had been done correctly.  Customer Service informs me that the corporate store did not cancel the contract and that I had to go back to  have them cancel it.  My son goes in and gets them to do that.  Great.  So I get my bill and I'm still being charged for the phone.  OK.  I call customer service and they clarify that the phone is mine and I have to pay it out.  No problem.  I understand the contract requirements.  Oh well right? NOOOOO!  I go back to the corporate store to retrieve my HTC one phone and they tell me they don't have it anymore.  Furthermore there is nothing they can do about it and I will continue to see the charge on my bill until I finish paying for the phone.  I call corporate and speak to Antonio - a supervisor- and he informs me that I can go to the store and dispute it with the manager who just informed me he would not give me my phone back and that I would still have to pay for the device.  REALLY?  MOM:  Go ask your dad    DAD: Go ask you mom  REALLY?  They are blaming each other and no one is resolving THE PROBLEM.  I don't care who is at fault...give me my phone back so I can see/use what I am paying for.  I have 5 phones on my plan and have been with this company since Western Wireless, Cellular One, Alltel, and Verizon.  No one had failed me til now.  They keep referring to the 'NOTES' that everyone has been putting in the system.  Some of it is true.  Some of it is not.  But they only go by what their people are noting.  What about me?  What about MY truth?  I cannot believe what is happening.  Just because you put people in those positions doesn't mean they are honest and capable.  So now what?

    I had the same thing happen to me recently. I went to Best Buy and did the Early Edge option to get an LG G3. Best Buy tells me I have to send my iPhone 5S to Verizon within 14 days to not get hit with a fee. I send in my iPhone after two days.
    Fast forward a week and I decided I didn't want to have the extra monthly cost added to my bill. I call Verizon before I return anything, and they said "Oh when you return it you will go back to your normal 2 year contract and once we get the phone back you can go to a Verizon store and pick up a refurbished iPhone 5S". I return the phone to Best Buy and was fortunate enough to have an older work phone lying around to use while I go and pick up a replacement device.
    NO SUCH LUCK. Verizon said that in the Edge agreement once I send the phone away they don't have to give you anything back even if you cancel it. How this is not considered robbery is beyond me. Also, how any lawyer or judge would agree that an agreement like that is legal is also beyond me. So Verizon pretty much took $400 from me.
    The customer service rep actually said I could either buy a phone off eBay or re-join the Edge program. I respectfully told them I wasn't going to give Verizon any more of my money considering they just took $400 from me. It's sad that you get told one thing by Support, and then they screw you the next minute. Definitely canceling my service when I can and not recommending Verizon to anyone since they won't do the right thing. 

  • SCOM2012 dashboard from where is the data

    I wonder which data is used in dashboard on SCOM2012? Is it from
    OperationsManager db or OperationsManagerDW db? Important to understand when you tuning the MPs.

    Data within the console, including dashboards will come from the opsman db.  The opsmandw db is used only for reporting, and aggregates data at 1 hour intervals for its highest frequency.

  • Where is the Adobe Flex Style Explorer Sample App

    Hello,
    I was finding this app extremely helpful since I was styling controls verry easy with it, and then just copy and pasting it to my css file.
    Now this app is not reachable any more.
    Can someone help with a valid link ?
    Thanks!

    brooklynpowerandlight:
    I realize this has been unresolved for a few days now and I sincerely apologize for this. We hope to resolve this issue with Apple as quickly as possible.  The revel team members do care about our users and are working diligently to remedy the situation. We will post updates as soon as we have resolution.
    Pattie

  • From Where MRM_XACCITCR_EXPORT is fetching the values in XACCIT in MIRO

    Hello all,
    I am debugging the MIRO transaction code in SAP, I want to know that from where does the function module
    MRM_XACCITCR_EXPORT fetches value in  XACCIT.
    i found that the table XACCIT is refreshed and has no records but o entering the function module it gets the records from somewhere which i am unable to find out. any help in this regards will be valuable for me. i am sharing the piece of code for your refrence and the program name is SAPLMR1M.
    CALL FUNCTION 'MRM_XACCITCR_EXPORT'
           TABLES
                T_ACCIT = XACCIT
                T_ACCCR = XACCCR
                T_CURR  = XCURR.
    Thanks And Regards,
    Sahai.S

    Hi,
    I think this internal table will be filled in fm MRM_INVOICE_POST (maybe in simulation mode, see import parameter I_SIMULATION for that).
    Regards,
    Klaus

  • Where is the password for user SDM stored in sap system?

    Hi SAP Gurus,
    We recently changed the password of the user j2ee_admin in our dual stack system where our UME is ABAP.
    Now, we have made changes in the su01 and configtool but after the system restart, the user id j2ee_admin is getting intermittently locked.
    On starting the the JSPM/SDM, we found it still uses the old password so wanted to know that from where does the user SDM picks up the password and starts.
    Searched few blogs and found that it reads from secstore of configtool. Could you please help.
    Regards,
    Himanshu

    Hi Himanshu,
    SDM uses encrypted administrator credentials stored which are stored secure store to use deploy service.
    If you have changed the password, updated in secure store and is correct, the you should be able to logon to VA.
    If not, then
    Goto /usr/sap/SID/DVEMBGSXX/SDM/program/config and open sdmrepository.sdc file to see the values of SecStore.properties and SecStore.Key are pointing to correct path. You can verify this from configtool or config.properties in configtool folder.
    If you are not able to save this password in configtool, then refer 1228507 - Config Tool does not properly save password in Secure Store
    Regards,
    Divyanshu

  • Where are the contents of GPnP profile stored?

    On my 3 node RAC setup using SCAN with GNS,
    I renamed GPnP profile on one node , stoppped clusterware on that node and tried to restart it. The c/w started and GPnP profile file was automatically recreated with name pending.xml. The moment I changed the value of ASM_DISKSTRING parameter using SQL, pending.xml was automatically renamed to profile.xml and ASM_DISKSTRING value was updated in it. I presumed that GPnPd copied the profile from one of the other nodes.
    Next I renamed the profile on all the nodes, stopped clusterware on one of the nodes and restarted it. But now again the same thing happened as earlier i.e. it was created as pending.xml and was renamed to profile.xml when updated via SQL. From where were the contents of the file read? Is it OLR?

    I am renaming ghome/gpnp/hostname/profile/peer/profile.xml
    Following post explains all I did:
    http://oracleinaction.blogspot.in/2013/01/LOSEGPNPPROFILE.html
    Pls also clarify why do we have gpnp profile in two locations?
    Edited by: user12288492 on Mar 18, 2013 8:32 PM

  • Where does the router fallback to load IOS when the IOS in flash memory is corrupted?

    If the ios image stored in flash is corrupted from where does the IOS is picked up?

    Hi,
    The following details the router boot process:
    1. The router is powered on.
    2. The bootstrap program (ROMmon) in ROM runs Power-On Self Test (POST)
    3. The bootstrap checks the Configuration Register value to specify where to load the IOS. By default (the default value of Configuration Register is 2102, in hexadecimal), the router first looks for “boot system” commands in startup-config file. If it finds these commands, it will run boot system commands in order they appear in startup-config to locate the IOS. If not, the IOS image is loaded from Flash . If the IOS is not found in Flash, the bootstrap can try to load the IOS from TFTP server or from ROM (mini-IOS).
    Last if it doesnt find the software anywere it would end up in rommon mode.
    HTH
    Regards
    Inayath

  • Howto find out location from where class was loaded

    Hi all.
    Is there any way I can find out from which directory, jar or url a certain object/class was loaded?
    Somewhere in the code the object is instantiated (class is loaded). E.g. like so:
    SomeObject someObjectInstance = SomeObjectFactory.getInstance();
    Can I use this object to find out from where in the file system it was loaded? E.g.
    someObjectInstance.class.fooMethod() or
    someObjectInstance.class.getClassLoader.barMethod()
    Thanks for any help.
    Joe

    Usage is actually like so:
    MyClass myInstance = (...)
    myInstance.getClass().getResource("/package/MyClass.class") returns the url object, pointing to the class;
    if you want a string instead, simply append toString():
    myInstance.getClass().getResource("/package/MyClass.class").toString()

  • FinalCut Express - where is the serial number ?

    I had to change motherboard on my macbook pro (not hard disk), and then final cut express ask again for serial number - I have the original box and cd, and cant find this number !
    ==> where is the serial number ?

    There should be 2 peel-off stickers attached to the documentation.
    Very distinctive as the print at the top is red and the numbers below are black.

  • Where's the Menu?

    I have updated my Maps and the new version is driving me mad. Where is the Menu option gone to allow me to choose between walk and drive etc? All I have now is a Dive Widget. Why cant I just start Maps and choose to search or select a location and then choose to walk or drive to it?
    This new update seems very cumbersome to navigate around - is there a Manual Update that explains how all this is now supposed to work?
    Also when I choose the 'Download own vioce' option it takes me to the Nokia Store and then tells me 'this Item is no longer available for download' - whats's going on/

    @Lazarus1540
    No clues as to what device you are using, but don't you still have a Nokia Maps "Compass" to launch application > Search > longpress to reveal further set of options?
    Can't use Own Voice with Nokia Maps v3.08 which is why not available.
    As pointed out by cataholic here is guide for v3.08 Anna version:http://nds1.nokia.com/phones/files/guides/Nokia_Maps_3.08_Anna_UG_en_GB.pdf
    Happy to have helped forum with a Support Ratio = 42.5

  • Where are the scripts that make Flex apps work with the JAWS screen reader?

    From the adobe website:
    To use the JAWS screen reader with a Flex application, users must download scripts from the Adobe accessibility website before invoking a Flex application. Screen readers work best when in Forms mode, which lets users interact directly with the Flex application. These scripts let users switch between Virtual Cursor mode and Forms mode by using the Enter key from almost anywhere within a Flex application. If necessary, users can exit Forms mode by using the standard JAWS keystrokes.
    Users can download these scripts, and the installation instructions, from the Adobe website at www.adobe.com/go/flex_accessibility."
    The link is broken and the marvellously dense chat support person said that Adobe doesn't support Flash Builder.
    Where are these scripts located?

    user8757041 wrote:
    I successfully installed oracle 11gR1 but the network configuration is not complete. can I still connect to the database server from XP? How? I am new in connection, even different OS. I use putty and I can access the command line as root or other users.(after I edit IP address at Network Configuration)
    I installed OEL 5.3 not on virtual drive, but directly to my desktop computer.
    what is connection database software?? is it different from putty?
    where can I get the DMS? ( data mover scripts, am I right?)
    wait for your response..
    regard.I'm afraid, I don't follow you very well. Anyway, if you have a db, with a running listener, you should be able to connect from any client over your local network (even through different OS). In that case, you'll need a client software (i.e. Oracle client runtime installation). Regarding the DMS, you should be able to find it onto the client after Peopletools/Peoplesoft application installation.
    Nicolas.

Maybe you are looking for