Front JUSB1&2 NOT WORKING - Please Help
I'm in the middle of a new build and everything is fine except....
I Can't seem to get Jusb1 & 2 pin sockets to work on KT6V-LSR M/B.
Rear hardwired USB's are working fine, is there something in the Bios i've missed?
I'm trying to connect up an internal 3.5" Multi Card Reader, using USB 2.0.
The cable is a four pin (5v, Data+, Data- and Ground). I have tried JUSB1 & 2, pins 1-7 and 2-8 (as per M/B book)
I'm using Windows XP (SP2) and the reader is plug and play, but nothing is happening not even a power light.
Thanks in advance for all your replies
Djtom
Well from looking at a jpeg of your board the front usb headers are laid out just like my board. Each set of headers support 2 usb ports each. That gives you the 4 in the rear and 4 for the front.
Now as to the pinouts, 1+3+5+7+9 is 1 set and 2+4+6+8+10 is the 2nd set, with pins 1 and 2 being the 5V power pins. Pins 7 and 8 are your grounds. 3 and 4 are the usbo- and usb1-. Pins 5 and 6 are usbo+ and usb1+. Pin 9 is the "key" pin and may actually be missing by intention. Key 10 is sometimes called the usboc pin and normally isn't used. On some boards you don't want anything connected to pin 10, even if you have to snip the wire going to it and terminate the end of the wire with insulating tape.
Your motherboard manual should show you the pin layout.
Similar Messages
-
Front audio port not working please help..
Hey guys,
My HP Pavilion DV2275ea front audio jack does not work, I have tried many different headsets as the mic jack works just fine. I have tried reinstalling audio drivers (Conexant High-Definition Audio Chip) and still nothing. I have look at the support advice posted to no avail. Is there anything else i could try?
A friend said it could be turned off in the bios but i am not able to get in as i don't know the password for the phoenix bios, could this be true?
Any help will be greatly appreciatedWell from looking at a jpeg of your board the front usb headers are laid out just like my board. Each set of headers support 2 usb ports each. That gives you the 4 in the rear and 4 for the front.
Now as to the pinouts, 1+3+5+7+9 is 1 set and 2+4+6+8+10 is the 2nd set, with pins 1 and 2 being the 5V power pins. Pins 7 and 8 are your grounds. 3 and 4 are the usbo- and usb1-. Pins 5 and 6 are usbo+ and usb1+. Pin 9 is the "key" pin and may actually be missing by intention. Key 10 is sometimes called the usboc pin and normally isn't used. On some boards you don't want anything connected to pin 10, even if you have to snip the wire going to it and terminate the end of the wire with insulating tape.
Your motherboard manual should show you the pin layout. -
I have 4s iPhone , I download the iOS 7. Now the front receiver microphone is not working , please help me that how to fix the problem.
I live in South Africa, and I had the same problem with my iPhone 4.
After weeks of frustration and swearing, I was in the process of restoring my phone to a previous iOS. To do that you need to turn the "Find my iPhone" option off, since i turned it off, my problem was solved. No need to repair anything or revert back to old iOS.
***** that i cant use Find my iPhone, but atleast i can use my phone. -
my iphone 4s does not start by power switch, it starts when i connect to pc. the proximity sensor is not working. please help.
Sounds like it may be a hardware issue.
Please contact Apple Support in your country.
Here is a list of numbers: http://support.apple.com/kb/HE57
Regards
J -
I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4
I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4
-
I installed windows 7 on my macbook pro. all is working but lan adaptor and sound od laptop is not working. please help me or send the link where i can download the these drivers.I have lost my resource cd .
If you are running Lion or Mountain Lion, the drivers are downloaded from within Bootcamp Assistant. If you are running Snow Leopard the drivers are on your Snow Leopard install disk.
Read the Bootcamp Install Guide for your version of OSx. http://www.apple.com/support/bootcamp/
Bootcamp questions should be asked in the Bootcamp forum where the Bootcamp gurus hang out https://discussions.apple.com/community/windows_software/boot_camp -
this is what my iphone 4 shows. iv tried switching off again and again, closing apps by double tapping the home button but still not working. please help.
is there any other method to download ios 6.1.2.
my phone is not being recognized by itunes on my new windows 8. neither its working on touch copy.
kindly help.
thankswell in thatcase, i need another help .
thanks for your instant reply.
i have currently bought a new laptop (windows 8) and my iphone is not being recognized by itunes.
because i have no backup on my previous laptop, i downloaded touchcopy but even touch copy is not recognizing my iphone. -
while updating 4.0 version to 5 version system shows sim card is not valid. My iphone is not working .Please help me
I would imagine your iPhone was hacked to make it work on your local carrier.
Updating the iOs to 5.xx will lock it back to the original carrier .The carrier holding the lock are the only
entity able to authorise the unlock .You will have to contact them and see if they unlock and the terms the apply -
HT1414 my handsfree is not working please help me
Hi There!
I am using Iphone 4s and ny handsfree in not working please help meTry restarting you iPhone by holding down the on/off and the home buttons at the same time until you see the Apple logo.
-
I have ne iphone 5, i been setting my email using AT&T global but it is not working, please help me on the correct configuration
Contact the email provider and obtain the correct setup information.
-
The built-in mic in g50 122ca laptop model is not working. please help me out.
the built-in mic in g50 122ca laptop model is not working. please help me out. OS: Windows Vista (32-bit)
here is a sample code .
so far you procedure looks good but
i bet you have to specify the name of report , instead of 'filename'.
see this
Plist_id := GET_PARAMETER_LIST('P_name');
IF NOT ID_NULL(Plist_id) THEN
DESTROY_PARAMETER_LIST(Plist_id);
END IF;
Plist_id := CREATE_PARAMETER_LIST('P_name');
ADD_PARAMETER( Plist_id, 'P_Receive_date', TEXT_PARAMETER, TO_CHAR(Receive_date,'mm/dd/yyyy'));
ADD_PARAMETER( Plist_id, 'P_Hearing_date', TEXT_PARAMETER, TO_CHAR(Hearing_date,'mm/dd/yyyy'));
ADD_PARAMETER( Plist_id, 'P_Hearing_time', TEXT_PARAMETER, TO_CHAR(Hearing_time,'mm/dd/yyyy'));
ADD_PARAMETER( Plist_id, 'P_Issue_date', TEXT_PARAMETER, TO_CHAR(Issue_date,'mm/dd/yyyy'));
ADD_PARAMETER( Plist_id, 'P_Workshop_date', TEXT_PARAMETER, TO_CHAR(Workshop_date,'mm/dd/yyyy'));
-- RUN_PRODCT(REPORTS,'..\Reports\Pro_License',SYNCHRONOUS, RUNTIME, FILESYSTEM, Plist_id, NULL);
-- here Pro_License is the name of report.
did you tried to see if the parameter passed using a message ?
try
message('parameter name'); pause; write this before "run_report". -
my itnues for pc is not working it shows that iTunes has stop working,I have downloaded Itnues many times but still it is not working, please help me
Please helppppp
-
All my old tv shows are not working please help my computer sed I have to Atheris 5 computers to play all my old tv shows I Pade for with eney Itunas cards.
What do y mean by not work?
What happens when y try to play them on yur iPod?
What happens when yo try to play them in iTunes on yur computer?
If you get a message what is the exact wording of the message?
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
Some countries do not allow redownloads some kinds of media -
The click at touchpad is not working, please help!!!
I use Macpro, recently the click at touchpad is not working, please help!!! Thank you !!
For this issue AppleCare support told me to so a SMC reset as follows:
Power the machine OFF.
At the SAME TIME hold down the following buttons:
Shift
Control
Option
Power
Then release all buttons. Power up the Macbook and see if the trackpad button work.
Hope this helps.
Bill -
hi
i tried to update to ios 8.2 on my iphone 5s when message popup to me now my iphone not working, please help i dont want to lose my dataWhat is the exact text of the message you got? And did you not back up before you updated?
Maybe you are looking for
-
Service Entry Sheet (SES) Error
Dears, We have 1 line item and 4 sub services in PO. We created SES for the first 3 items. Now the 4th service is completed, when we are creating the SES, it is asking for price (although the price is available in the PO). Even though when we ente
-
Can't get rid of the "your document is being tracked for reviews" message
I used Adobe Professional for the first time to conduct reviews on PDFs. I used the "Send for review by email" option. Now I am done with the review, have incorporated the comments, have compiled FrameMaker files, and produced a new PDF. But when I o
-
Problem with hostednetwork in win 8.1
when ever i connect my laptop using netsh wlan set hostednetwork it gets connected to my android mobile but the connection disappears after few seconds...I had tried disabling the WiFi and enabling it and again creating with new ssid but still happe
-
Where has my itunes folder gone??
Hi there, I recently opened a new itunes folder for my sister's music and now I don't know what has happened to my own folder and all my music. Can someone please tell how I am able to access my itunes folder/library? Any help would be appreciated! T
-
Table name to know the infoobject is flexible or direct.
Hi, Please let me know the table name where we can know whether the infoobject is flexible or direct update. Thanks in advance! Best regards.