Front panel audio jack is not working on K9N Neo V2

My front panel audio jack is not working on K9N Neo V2. I check the JAUD1 cable and it appears to be connected to the front panel audio jack. My soundcard driver cannot detect any gadgets when I plug it in the front panel. My audio drivers and BIOS are up to date. Is there any known solution to this? My computer is only a few months old and I have not tried the front audio jack until recently. I'm on Vista home premium btw.
Also, I've got another problem, my processor is AMD 64x2 4400+ overclocked to 2.63Ghz. I've been using that clock value ever since I built this computer and stress tested the processor and found that it would not cause any problems like hanging or overheating. However, I recently decided the need for AMD's Cool & Quiet technology and enabled it. It caused BSODs every few days or per week that didn't happen before. I tried it with the default clock value and it still causes BSODs. Can someone help me?

Quote
Thanks. Its ironic that disabling it actually enables it.
It has to day with the front panel audio wiring of your case. How many wires are there that can be connected to the board's pin header?
Quote
Sound quality isn't very good
Can you be more descriptive? Is the quality better if you plug the headphone into one of the jack at the back panel? (Also, make sure you tell the Realtek HD Audio Manager, that a headphone is connected (and not regular speakers).

Similar Messages

[SOLVED] Front audio panel still not working on K9N Neo V3

I already posted on this here: https://forum-en.msi.com/index.php?topic=113813.0.
I still didn't get front audio panel to work on MSI K9N Neo V3.
Even with my new case; Sharkoon Revenge, it is not working. It wasn't working on my previous noname case too. However, front audio panel on my previous case was working on several other MBs except on this MSI K9N.
Now, I'm using the latest Realtek HD audio driver. I think it's from February '08. Just as with the driver dowloaded by Vista via Windows Update, anything plugged in front audio panel isn't recognized. In this new version of Realtek driver I can't find this Disable front audio panel option so I can't tell if it is checked or not.
Once more, there is not much to do wrong while connecting. Case front audio panel cabel is the same as on all other cases I've ever seen/had. It's a cable with the same number and position of pins as in all other cases. It fits fine on MSI K9N Neo V3. Rear audio panel is working fine.
Any solution to this!?

Quote from: Jack the Newbie on 07-April-08, 03:25:15
From what I can see from the Sharkoon product page, the front panel connectors of your case are not compliant with the Intel HD Audio Pin Standard.
Do you have a manual for your case that includes Pin/wire definitions for the front audio connectors?
No. There was no manual in package. I never thought I will need one either.
Here is Sharkoon Rebel Pin Assigment; http://img176.imageshack.us/img176/9729/pinslk2.jpg
Quote from: Jack the Newbie on 07-April-08, 03:25:15
Have you tried disabling automatic front panel jack detection in the Realtek HD Audio configuration utility? If you don't know were to find that option, access the tab labeled "Audio I/O" and click on the tool icon.
Yes, I tried disabling it. Two tabs (front audio out and front mic) appeared but none of it works.
Quote from: HenryW on 07-April-08, 03:35:46
From something I read: You can also physically check the audio cable of the front panel audio solution. If there is a cable connected to Pin 4, you have an HD Audio module; if there is no cable to Pin 4, you have an AC97 module.
I don't really understand this. Could you please check this on Pin Assignment scan I uploaded above!?

Speaker and audio jack is not working

My laptop speaker and headphone jack is not working.So am not able listen anything on laptop.Please give me a solution on it.

Hi ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP Pavilion g series Notebook and issues with the sound. Here is a link to help troubleshoot issues with the sound. Please note remove any and all USB devices. Disconnect all non-essential devices and headphones, as these could cause some issues. Here is an automated tool for troubleshooting Windows 7. It has a built in Audio repair built into it. I hope this helps with the sound. Thanks.

Microphone speaker and audio jack is not working?

hi i buy a I phone 5 S in march from E max UAE . Its been 3 month only but my phone audio jackpot is not working ,microphone and speaker is not working moreover if i open some app for longer time and during charging it get hot. I took the phone to the store tell them the problem and the phone is in warranty also but they didn't change the device they say we cant change and just repair the device. its been two days my phone is back again i am facing the same problem .can anybody suggest me where should i go for complain and what i will do to change the device.

I've asked the hosts to relocate your post to the iPhone forum -> Using iPhone - this is the MacBook Pro forum.
Good luck,
Clinton

Back panel audio jack is not disabled after I plug into the front

The speakers go on playing even with the headphones plugged in on the front panel
I tried all of the combinations of checkmarks in the Realtek HD Audio utility
I got MSI P965 Neo-F
current driver is 1.71, I'm going to update to the latest, but don't think this will remedy the situation
Please help! This is not really disastrous, but I'm so annoyed when something does not work the way it was designed!

Are you trying to suggest I should include detailed computer specs?
Because the moan guide does not list any problems similar to mine
I don't think it will help me get relevant help, but I'll try:
CPU Conroe 6420
Samsung memory 2x1024 DDR2667
XFX GF7600 256 PCIE
Seagate 320Gb SATAII
WinXP Pro SP2
PSU FSP 400 W

Front audio panel not working on K9N Neo V3

A new problem with MSI K9N Neo V3 MB...
I just found out that Front audio panel is not working (no mic, no line out). I checked the cable 3 times. Seems to be OK. Front panel was working on a previous ASUS motherboard.
- All drivers according to vista are working fine.
- Back panel sound (eveything) is working fine.
- Sound panel says that front panel mic & line-out are not plugged in.
Is there a switch to turn this on? Or maybe some special driver?
Or it is just useless, and working on MB package advertisment only?

Quote from: Richard on 13-January-08, 06:50:13
P.S. Just a thought, I could go get a Ouija Board or Dart Board if you prefer. Might yield some answers.
You sure are funny. No doubt about that.
I do appreciate a good laugh, but in this case laughter won't solve my problem.
This little analogy with a car and a tire is just ridiculous. You know, tire is flat or it is not. Or is it maybe flat only on BMW cars?
I see no purpose in describing cables here, but if this is what would make you happy... It happens that I have few spare mintues, so here we go.
chapter 1. - The Case
I do not know what brand is my case. It's a cheap case with expensive Corsair 550W PSU. Very well cooled. I also don't know what is its name, so let us just call it George.
Here is George roaring on my desk;
Chapter 2. - Jimmy & Gina
This is an unknown brand, no name Front panel cable so let's just call it One eyed Jimmy;
This is local one tooth missing whore called Gina;
Chapter 3. - Encounter 1
Jimmy fills Gina just right. It's very tight but just right;
Chapter 4. - Berta, Gertruda and Mike
Dirty Twins Berta and Gertruda are ready to recieve some massive waves;
Big Mike is ready to give:
Chapter 5. - Encounter 2
It fits right again:
Chapter 6. - Oh NO!!!
It's not working on MSI AGAIN:

Audio jack does not work after 10.9.1 update

Hi folks --
I have had an issue for a while now that maybe some of you have seen.
I have a 2011 iMac 27, and upgraded to Mavericks months ago, no issues. For the holidays I bought an AppeTV 3rd gen for the wife, and after setting it up on the network, I can no longer play audio throught the audio out jack on the iMac to powered speakers.
Now, the issue is, I cannot tell if it stopped working before the AppleTV got added to the mix, or after a Mavericks update. It has been about 3 months...
The machine is out of warranty, and I have the sneaking suspicion that the audio jack on the motherboard is to blame... but not certian. Has anybody had that issue or seen it be an issue? I consider myself pretty up to date on the Mac support sites like Macintouch and iFixtit, but have not seen anything regrading this issue on this model.
I have done a deep clean with Onyx, zapped the PRAM, and done a few restarts. No joy.
Anyone have any wisdom to impart?
Thanks in advance
Michael

Raymond Rogoway wrote:
Used Software Update to update to 10.5.1. Now my install disk will not boot. Drive kicks out disk after awhile. Ran Disk Warrior which reported no changes. Repair permissions.
Ray
Does the disk also get ejected when you are running Leopard, or only when using it for booting?
Have you looked at it physically for scratches or that dirty film some DVDs had?

Audio jack port not working

i installed windows 8.1 on my laptop HP 655 and i have high definition audio device drivers installed but i cant hear any sound from my headphone or external speakers when i plug the audio jack in its port. but the internal speakers are working well... please help

Dear gbonyo -
I understand that after installing Windows 8.1, your speakers and headphones do not work. Well, that's annoying... I will try to help.
- Before going through these steps, make sure that the speakers and headphones are connected to the correct ports. (I know this sounds silly, but sometimes it happens.)
The first and simplest thing to try is the audio playback troubleshooting tool:
1. With the headphones and speaker plugged in to the laptop, type "troubleshooting" at the Start screen to open the Search charm, and then select Troubleshooting from the search results.
2. Under Hardware and Sound, click Troubleshoot audio playback and then click Next when the Playing Audio window opens.
3. A new window opens. Select the device you would like to troubleshoot. Then click Next and follow the on-screen instructions.
4. If a recommended action displays, select Apply this fix or Skip this step to continue to search for other problems.
If the above does not resolve the problem (and/or it does not find your speakers/headphones) it could be that the laptop does not know that it has speakers/headphones attached to it.
1. From the Start screen, type "sound" to open the Search charm, and then select sound from the search results.
2. Click on the Playback tab.
3. Right-click an empty area of the Sound window.
4. Click the check boxes to select Show Disabled Devices and Show Disconnected Devices.
If the device is listed as "Currently unavailable" or "Not plugged in," disconnect it, and
then reconnect it from the port.
5. Test the device by sending a signal from the sound source (For example: Play an mp3 file).
6. Look at the bars next to the device name on the Playback tab:
If the gray bars next to the line-in audio device name change to green, the device is active and an audio signal is passing through the line-in port. The issue should now be resolved.
If the bars remain gray and inactive, the computer is not recognizing a signal. Leave the Playback tab open and proceed to the next step.
7. From the Playback tab of the sound window click the port that you want to use (there could be one or more ports).
8. If the device you want to use contains a small circle with an arrow pointing down, the device is disabled. To enable the device, right-click the device name and select Enable.
9. Click Set Default to make this device the default line-in audio device.
10. Click OK to make the changes.
Please let me know if this resolves the problem. If it doesn't, we can try a couple of other things.
Sincerely,
dhtp
DH
I work on behalf of HP.
Please click "KUDOS Thumbs Up" if I have helped you, and click "Accept as Solution" if your problem is solved. Thanks for the feedback!

Print VI front panel to file does not work after building executable.

I am using a property and invoke node to print the front panel of my VI to an HTML file. It works fine in the development mode. After Building the application, this subvi will no longer
print the front panel. Is there some special files that included in the build??

You can use the Report Generation VIs to generate the HTML report. Specifically, you could use Append Front Panel Image to Report.vi and Save Report to File.vi to save the image of the panel to an HTML report.
Check out the examples in examples\reports to get a better idea how to use these VIs if you've never used them before.
Good luck,
-D
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

Audio jack is not working

I have bought a blackberry z10 4 days ago.When I test the headset on another phone it is working fine
But when I put it into my phone it doesn't respond.i have followed many ways
..pls guys any suggestions......I want my z10 to be perfect......pls help
Solved!
Go to Solution.

Well, your phone is still under warranty. I suggest you take it back and either have it fixed or have it replaced.

FRONT PANEL USB 3 PORTS NOT WORKING.

I have just had a new ASROCK motherboard fitted to my HP Pavilion base unit as it failed after only eighteen months & even though everything is connected correctly my USB devices are not detected when plugged in. The USB 3 ports are the original HP Pavillion ports & cable configuration & plugged into the new ASROCK board.
Specs:-
ASROCK Motherboard: H61M-DG3/USB3. http://www.asrock.com/mb/Intel/H61M-DG3USB3/?cat=Specif...
HP Pavilion 500-081ea base unit: http://support.hp.com/gb-en/product/HP-Pavilion-500-000...
I running Windows 8.1 Pro 64 bit.
Can anyone please help?

Those should be fixed with a chipset driver, which is packaged in the HP graphics driver. Did you install that yet? Don‘t do express install, but rather the custom install and check everything.

The right chanel in the audio jack is not working in my iphone4.

Does anyone have an idea what can it be?

yeep, tryed that already.and the headphons are fine.don't know what the **** can it be..

Front Panel Audio Problems

I'm trying to make sense of the JAUD1 descriptions and enable the front panel audio jacks to work but it seems the mobo doc and the casing connectors have entirely different descriptions.
The JAUD1 has these:
Pin1 AUD_MIC
Pin2 AUD_GND
Pin3 AUD_MIC_BIAS
Pin4 AUD_VCC
Pin5 AUD_FPOUT_R
Pin6 AUD_RET_R
Pin7 HP_ON
Pin8 Key
Pin9 AUD_FPOUT_L
Pin10 AUD_RET_L
The casing's connectors are:
Mic:
MICOUT
MICIN
AGMD (Ground???)
LineIn:
SPKO-R
SPKO-L
LineOut:
EARO-R
EARO-L
Reserved
What is going on??? Please help! ;(

Although it doesn't make sense as LineIn - SPKO_L/SPKO_R, I read as Speaker Out though. EARO_L/EARO_R should be headphone out.
Pin1 AUD_MIC - MICOUT
Pin2 AUD_GND - AGMD
Pin3 AUD_MIC_BIAS - MICIN
Pin4 AUD_VCC
Pin5 AUD_FPOUT_R - EARO_R
Pin6 AUD_RET_R - SPKO_R
Pin7 HP_ON
Pin8 Key
Pin9 AUD_FPOUT_L - EARO_L
Pin10 AUD_RET_L - SPKO_L

Help RE:Front Panel Audio and Sound Blaster Live! 24 Bit C

I own Soundblaster Li've! 24-bit card.
I would like to make use of the front panel audio jacks on my case but i have no idea where on the card to connect the pins on the card ( the pins are:Mic In, Mic Power, Ear R, Ear R, Ear L, Ear L, GND)
Anyone know where exactly do each of these pins go?

Maybe this site can give some light on this matter - http://audigy2zshowto.blogspot.com/
jutapa

K9N2G Neo Front panel audio not working

I have plugged in various cases and i/o bays into the audio connector on this mb and NONE of them work. Yes I have tried the "disable detection" option with no luck. I am currently trying to use a silverstone fp32 i/o bay that definately supports hd audio but it still doesn't work. I made no wiring mistake as it was a plug and not seperate wires.
http://www.silverstonetek.com/products/p_contents.php?pno=fp32
What do I have to do to get front panel audio that was promised with this board?
edit: you know I have NEVER had trouble with AC97 yet I have NEVER gotten HD audio to work properly EVER

It doesn't follow AC97. But it is a Realtec chip, and they often run into problems. For example they'd like their drivers installed while in SafeMode.
Where exactly did the problem come up? Is the HD controller enabled, (BIOS)?
Is this relevant, stolen from the Englizsch only manual:
"When you are playing the first audio source (for example: use Windows Media
Player to play DVD/VCD), the output will be played from the rear panel, which is the
default setting.
Then you must to select the Realtek HD Audio front output from the scroll list
first, and use a different program to play the second audio source (for example: use
Winamp to play MP3 files). You will find that the second audio source (MP3 music) will
come out from the Line-Out audio jack of Front Panel."
Off: Think this is the first time this board come before my eyes in this forum.

Front panel audio jack is not working on K9N Neo V2

Similar Messages

Maybe you are looking for