Front Panel Audio - P7N Sli Platinum Question

I am having trouble getting the front panel audio working - I want it set up so that when I plug my headphones in the speakers mute and the headphones take over.
I have the following:
Case - ThermalTake Armor VA8003BWS - http://www.thermaltake.com/product/Chassis/fulltower/armor/va8003bws.asp
MB - P7N SLi Platinum
Sound Card - Create Labs Xfi Gamer
I have done the following:
1. Disabled onboard audio in Bios (should I turn this back on?)
2. Went into Creative Console Launcher and checked the 2 options that I want it to automatically enable headphone settings and mute speakers when headphone jack is connected.
3. Connected 10 pin wire in case labeled (Azalia) to the motherboards Jaud1 (my MB manual says it is Azalia 1.0 compliant). The case also has an AC'97 connection (on the same wire as Azalia but I didn't use this because of what I read in MB manual about Azalia 1.0 compliant).
4. The case also came with this 10 pin black block that has all the Azalia descriptions on the side (Port 1 L, Port1 R, Port2 R, Sense_Send, etc. - I tried plugging the Azalia connector into this and then this into the Jaud1 but still nothing).
Not sure if it matters but my headphones are Plantronics Gaming Audio 770 (not USB).
Any suggestions?

Quote from: [LT]Eternalbliss on 21-June-08, 03:43:49
I've just recently had this similar problem. I think the issue in your case is step 3. I believe you should connect the Azalia 10pin wire to your X-fi card, not the mobo.
My problem was that i had connected AC97 10pin wire to my X-fi, after which plugging in my headphones didn't mute my speakers.
That was the problem - works great now! Thanks

Similar Messages

Front panel audio problem Neo2 Platinum

Hi
I have a S775 915P Neo2 Platinum motherboard which I would like to connect to a Thermaltake Tsunami Case (front panel) but I don't know how to do this since the names on the cables from the case don't match the motherboard.
The cables from the case has the following names:
MIC VCC
MIC IN
RETURN L
RETURN R
EAR R
EAR L
GROUND
...and on the motherboard:
PORT 1L
GND
PORT 1R
PRESENCE#
PORT 2R
SENSE1_RETIRN
SENSE_SEND
KEY
PORT 2L
SENSE2_RETIRN
How do I connect theese?
Thanks!
//Thomas

Not the same MoBo, but maybe some of these links will help,
https://forum-en.msi.com/index.php?topic=72497.0
https://forum-en.msi.com/index.php?topic=62730.0
Personally I prefer USB in front and Audio back with a mediahub /adapter on the monitor.
Cheap, simple and functionally.

Front Panel Audio P7N - WEIRED! NOT USUAL!!

Hi Guys
FIRST - No this is not the usual Audio Problem
I have figured it out how to Put the Front Audio connections OK (I think so)
Anyways the thing is, i am using Rear HeadPhones attached to the back panel. Now when i insert the FRONT Jack for Headphone, The Sound Control Of Realtech thinks that that I have REMOVED the Front Jack and starts playing through the REAR, BUT, when I remove it says (message Pops Up) that it has been inserted in the FRONT ZOINKS!!!
Why is it giving me Opposite Messages and configuring itslef in REVERSE?
I have installed the latest HD Audio Drivers from Realtek but no use.
I then turn of autodetection and let it Play through BOTH Front an REAR, thats the only way it runs.
Also the sound from the FRONT is not very good, when i move the slider to LEFT or RIGHT (the one slider below the Volume), the Voice clears up a bit , otherwise its mingled (sorta)
HELP!!!!
V annoying.
Here's my Config; all latest Drivers and BIOS 1.1 is being used.
MSI 750i Platinum
E8400 @ 3.6GHz with Thermalright 120-Ultra Extreme
Corsair TWIN2X4096-6400C4DHX
8800GTS 640MB
Xi-Fi Xtreme Gamer Sound Card, Outputting to Creative 4.1 surround Speakers
Ez View TV Tuner + Plextor ConvertX PX-AV200U
Hard Disks (Maxtor 500GB,WD Ext 500GB, Seagate 320GB, Seagate 200GB ATA)
LG DVD Write, Light Scribe - SATA
Samsung LCD 22" 2232GW

Quote from: Adoctor on 23-June-08, 19:06:41
Thanks for the reply
But Mmmm what do you mean
Can you please give me some details as what to check?
Take the mainboard out of case.
Then power up, being very careful.

MSI K9N PLATINUM FRONT PANEL AUDIO

Hi everybody
I recently mounted an MSI K9N Platinum mainboard. When connecting front panel audio from case connectors on JAUD1, case connectors are marked as follows:
MIC POWER
MIC IN
GROUND
R-RET
L-RET
R-OUT
L-OUT
which does not match with those written on mainboard user manual for JAUD1 which are FRO PIN 1 TO 9 as follows:
PORT1L
GROUND
PORT 1R
PRESENCE
PORT 2R
SENSE1_RETURN
SENSE_SEND
KEY
PORT2L
SENSE2_RETURN
.I´ve tried to connect it on many combinations but yet it is not working.
Could someone tell me the right way to do it?
Thanks in advance.

I think you better ask this question to the manufacturer of the frontpanel stuff, as I have no clue.

K8N Neo Platinum + Sonata Front Panel Audio Problem

Hello,
The front panel audio speaker output is reversed when using headphones on my K8N Neo Platinum and Antec Sonata case. If I swap the left and right front panel audio output signal connectors, the headphone speakers are fine, but then my normal front speakers are reversed. All other connectors seem to be plugged in correctly. I've tried using nvswap, but doesn't seem to work on nForce3. Currently using Realtek driver version 5.10.0.5620 (had the same problem with the drivers included on mb cd) on WinXP Pro SP1 and 5.1 speaker setup (would like to use FPA for mic/headphones while gaming).
Let me know if you need any additional info.
Thanks.

I am having the same problem as well. Was able to correct front output jack by switching the connections. But rear audio is still backwards. I havent tried any sort of 5.1 or 7.1 channel audio setups

MSI P965 Platinum - Front Panel Audio u/s

Finally after managing to get XP Pro SP1 CD to install, I have a stable system, and thanks to those whom freely gave advice.
But we hit the next issue with this motherboard, the front panel audio.
Firstly the Realtek detection software doesn't detect anything plugged into the front panel.
Connected the cables as follows from my Coolermaster Stacker case;
mobo = case wires/colour
pin1 aud-mic = mic-in - yellow
pin2 aug-gnd = gnd - black
pin3 aud-mc-bas = mic-pwr - red
pin4 aud-vcc = empty
pin5 aud-fpout-R = R out - green
pin6 aud-ret-R = R ret - green
pin7 hp-on = empty
pin8 key
pin9 aud-fpout-L = L out - white
pin0 aud-ret-L = L ret - white
The above pin out gives nothing at all, but audio from rear ports on the computer motherboard is fine.
I also tried the following,
where the microphone wires were left disconnected, therefore just the speakers plugged into the front panel audio header
mobo = case wires/colour
pin1 aud-mic =
pin2 aug-gnd = gnd - black
pin3 aud-mc-bas =
pin4 aud-vcc = empty
pin5 aud-fpout-R = R out - green
pin6 aud-ret-R = R ret - green
pin7 hp-on = empty
pin8 key
pin9 aud-fpout-L = L out - white
pin0 aud-ret-L = L ret - white
The above still gave me no audio out from the front panel.
Intrestingly if I leave the front panel audio header blank, I still get rear audio fine, where I would have expected to have put jumpers across the L and R outputs as is the norm.
I have removed the front panel from the computer to ensure that the wires terminate OK, and have not been pulled out/off.
Have I plugged in the wires correctly?
Is there some hidden setting that I have missed, I admit that I do not like the Realtek audio software?
I cannot find any way to boost the microphone input since Realtek audio software has been installed.
One day case/mobo manufactures will use a standard for the front panel headers and front panel audio headers, and we will have a simple single plug to insert, rather than a group of single fiddly connectors that have to be attached to a header that was at the last minute attached to the motherboard as far away from the front of the case, and in the darkest most fiddle corner.
Oh well......
Cheers

AaronYuri - you're are so right there my friend. I just pity Joe User whom might attempt such a move themselves.
In the end my entire issue was software related, and that has to be blamed on Realteks software, far too many options approached from far too many different angles. Audio is really simple, plug your cables in, and it should just work, certainly in the simple case of 2-1 speakers and a microphone. Why exactly it took a couple of hours to figure out how to get the front panel microphone to be seen in the first place, let alone any signal, is beyond me.
So my cables were all connected correctly as per the MSI manual, confirmed by my Abit manual and other post here and on other forums.
In the Realtek MSI audio software, on the I/O Audio tab, connector settings, I had to select 'disable front panel jack detection' and 'mute rear panel output when front headphones plugged in'. The other option here 'enable auto pop up...' is unchecked.
After this the Realtek software mentioned something about a new profile had been set up?
I then went to Windows Control Panel, Sounds and Audio devices, and selected the voice tab, on this page I selected 'mic IN at front panel [pink]' from the drop down list for Voice Recording'. Proceeded to 'test hardware' and the microphone is now working. This option to select the input in the drop down list was not available before.
All a bit of POKE and HOPE.
But we seem to be there.

P35 Platinum front panel audio with Antec P180 case?

God I have a headache after reading all those "front panel audio" threads. Why can't mb's all use the same freaking pinouts!!!!
The case doesn't have a HD front panel.
MB pinouts are:
1. Mic_L (MIC Left Channel)
2. GND
3. MIC_R (MIC Right Channel)
4. PRESENCE#
5. LINEout_R (analog port right channel)
6. MIC_JD (MIC jack detect)
7. Front_JD
8. NC (empty)
9. LINEout_L (analog port left channel)
10. LINEout_JD
Case Front Panel connector is a preconfigured block with pigtails hanging off in case it doesn't match up.
1. MIC Signal
2. MIC Power (MIC BIAS)
3. Ground
4. FPOUT-R (front right)
5. FPOUT-L (front left)
6. RET-R (rear right)
7. RET-R (rear left)
glaring differences are the ground and the MIC connectors.
How do I connect these? I don't want to fry anything.
Thanks.

They do have the same pinouts. There are two standards is the reason for two different pinouts. It's just that your MB is Intel HD and your case is AC-97.
For Intel® High Definition Front Panel Audio
Pin Signal Name Description
1 PORT 1L Analog Port 1 - left channel (Microphone)
2 GND Ground
3 PORT 1R Analog Port 1 - right channel (Microphone)
4 PRESENCE# Active low signal that signals BIOS that an Intel® HD Audio dongle is connected to the analog header. PRESENCE# = 0 when an Intel® HD Audio dongle is connected
5 PORT 2R Analog Port 2 - right channel (Headphone)
6 SENSE1_RETURN Jack detection return for front panel (JACK1)
7 SENSE_SEND Jack detection sense line from the Intel® HD Audio CODEC jack detection resistor network
8 KEY Connector key
9 PORT 2L Analog Port 2 - left channel (Headphone)
10 SENSE2_RETURN Jack detection return for front panel (JACK2)
For AC-97 Front Panel Audio
Pin Signal Name Description
1 MIC Front panel microphone input signal (biased when supporting stereo microphone)
2 AUD_GND Ground used by analog
3 MIC_BIAS Microphone power / additional MIC input for stereo microphone support
4 AUD_GND Ground used by analog audio circuits
5 FP_OUT_R Right channel audio signal to front panel (headphone drive capable)
6 FP_RETURN_R Right channel audio signal return from front panel (when headphones unplugged)
7 AUD_5V Filtered +5 V used by analog audio circuits
8 KEY No pin
9 FP_OUT_L Left channel audio signal to front panel (headphone drive capable)
10 FP_RETURN_L Left channel audio signal return from front panel (when headphones unplugged)

975x platinum front panel audio

hi all. ive read every thing on this forum i could find, but can not get the front audio panel connectors to work. my case(sunbeamtech silent storm) has the single molded connector that only fits one way on mobo. in the msi audio control panel, nothing happens when i plug in mic or headphones, or if i disable detection of the jacks. im at the end of my rope. please help!

I had the same problems. I assume that the "AC97" jack is plugged in to the JAUD1 connector of your mainboard. You have to plug in the other jack (HD Audio) to the JAUD1 connector, after this the front panel audio should work.
Look here https://forum-en.msi.com/index.php?topic=104480.0 ...

P7N Diamond & P7N SLI Platinum & P7N SLI-FI

The main purpose of those Betas ===> Solved the Video Corruption and fix 9.5 CPU Ratio Multiplier for E8500.
P7N Diamond ==> A7510NMS.121 {06/06/2008} (V1.2B1) Attachment: P7N Diamond v121.rar
P7N SLI Platinum ==> A7380NMS.124 {06/06/2008} (V1.2B4) Attachment: P7N SLI Platinum v124.rar
P7N SLI-FI ==> A7380NMS.211 {06/06/2008} (V2.1B1) Attachment: P7N SLI-FI v211.rar
*** Flashing either of these BIOS' are at your own risk. Do not complain if you end up with a paper weight! ***
Flashing the safe way:
Use Method 1 or Method 2, both will do the same job.
Use it at own risk.
Before you flash!!:
Make and ensure PC is stable before proceed, remove any OC if you have.
Flash it via DOS mode by booting from USB key, CD/DVD.

Quote
Noobish question - is clearing the CMOS absolutely necessary after a BIOS update?
Yes, it is recommended to clear CMOS with main A/C power cable removed from PSU. There might be small changes in data structeres between BIOS Versions. Not clearing CMOS and resetting BIOS settings after flashing can have unexpected side effects.
Quote
I'm not really comfortable poking around inside my case apart from swapping a graphics card or hooking up power cables.
You don't need to "poke around" anywhere. You simple need to unplug the main A/C power cable from your PSU, which is outside the case, hit the power-on button to drain capacitors and then press the little button on the back panel of your board for a couple of seconds. That means you don't even have to open your case to clear CMOS.
Quote
So again, would NOT clearing the CMOS jumper thingy prevent successful update/boot?
If you restart your system after clearing CMOS, the BIOS will display an error message and prompt you to reset your BIOS settings, that's it. Nothing to be afraid of. The only risk involved is the BIOS Update itself, not the CMOS Clear.

HELP!!!!! P7n sli platinum cd-in problem.

Dear msi members.
I've got a p7n sli platinum board in, but now the cd-in (audio-in) (you know that 4 pinned thing you can connect a dvd drive too) connector on the board is in the way of my gtx 260, "they collide" now my question is, i'm pretty good at soldering, is it safe to unsolder the port completely?
as this way i'd have room for my gfx card.
If it's not. be sure to let me know how i can get this thing out of the way please.
Thanks in advance, Scorp.
P.s. Thats seriously my only issue, if i remove that thing everything will fit, (and i could mostlikely unsolder it carefully and resolder it should i need to rma). it's just the question that if i remove it completely does the board still run properly?

hello i have the same problem, i recently bought gtx260 to find out the JCD is on the way . I'm using my 2nd Pci-E slot at the moment. i was reading the forums and find out that this has been affecting many users with similar components, and they say they can remove the plastic as posted on this link http://forums.hardwarezone.com.sg/showthread.php?p=31163282 i
m not sure if that would void warranty or not

Help with front panel audio on K9N board.

Okay, I admit I'm a bit of a moron with front panel audio but I just can't figure out how to configure this board with my case. Here are the pins:
Case:
Mic In
Mic Bias
SpeakOut L
Return L
SpeakOut R
Return R
Ground
Motherboard:
PIN    SIGNAL      DESCRIPTION
1    PORT 1L      Analog Port 1 -Left channel
2    GND      Ground
3    PORT 1R      Analog Port 1 -Right channel
4    PRESENCE#     Active low signal -signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected.
5    PORT 2R      Analog Port 2 -Right channel
6    SENSE1_RETIRN     Jack detection return from frontpanel JACK1
7    SENSE_SEND     Jack detectionsenselinefrom the High Definition Audio CODEC jack detection resistor network
8    KEY      ConnectorKey
9    PORT 2L      Analog Port 2 -Left channel
10    SENSE2_RETIRN     Jack detection return from frontpanel JACK2
I haven't been able to make any sense of the two, so if anyone here can help, I would appreciate it very much.

Quote from: crazy on 09-June-06, 15:51:46
You may tell us more information about your mainboard, please give us the detailed name of your mainboard. :D Then there will be more users could give some suggestions.
Sorry, there aren't that many K9N boards out there, but mine is the K9N Platinum MS7250 Version 1.0. It's the AM2 non-SLI nVidia nForce 570 Chipset model.
Thanks for any help.

P7N SLI Platinum Unstable with over 2GB ram and/or dual channel memory on.

Hello need some help or to report something to MSI regarding blue screens, freezes when booting Vista 64 (SP1 + all fixes installed) with more then 2GB ram. Single channel mode works (either 1 stick of 2 GB or 3 sticks of 2GB) and is rock stable. Booting with 2 x 2 or 4 x 2 yields instability and blue screens.
I read over Microsoft's hotfix KB929777 however it appears this patch was applied during SP1. http://support.microsoft.com/kb/929777 - when I attempted to apply this hotfix I got the message this update does not apply to your system.
Memory tested in other gaming system using 4 sticks of G.Skill 1066 DDR2 ram and still have the same issues. Other forums like Evga.com, Tom's hardware and 411overkill.com tend to suggest some problem with this new bios version 2.0, written by Nvidia. Some others mention possibly an Nvidia nforce driver issue.
Therefore, under duress during testing - with 1 stick or 3 sticks of ram, all tests perfect and passes all stability tests, good marks in Sandra, plays any game. With 2 or 4 sticks of ram, very unstable won't stay up but for seconds.
Any ideas? (Tested 7 ways until Sunday!)
My other rig, rocks solid and stable with Vista 64.... It's the Evga new mainboard 780i with triple SLI (132-CK-NF78-A1), 8gb of Gskill 1066ddr2, MSI 8800GT (x2 sli mode) Q6600 @ 3.2 ghz - Raid 0 on dual WD caviar 640 gb/sata 3.0gb/sec. Seasonic 700w p/s. 8gb of memory and not a hiccup. Ram 2.0 volts, cpu @ 1.36v. Will handle the memory from both systems with out fault.
Considering I can swap memory back and forth and confirm it's not the sticks, swap graphics boards (own 3 of them!) and rule out that....
Fyi. Any help is appreciated!

Dump question, but have you pickup the correct update e.g. for 64bit? ==> http://www.microsoft.com/downloads/details.aspx?FamilyId=91672C7C-614B-404C-850C-377541E93C18&displaylang=en
"This comes inside SP1 for vista 64, as noted with my other system during the build. "
Better double check it.
Install all four memory sticks and do a memory check with >>Memtest86<< 1st, ensure that no error(s) will comes during testing.
Also how about that?:
Quote from: BOSSKILLER on 07-April-08, 23:55:36
Remove your OC then see how its goes.
"When the system boots in single channel mode (only 2 or 6gb of ram meaning 1 or 3 sticks installed into the 4 slots) its' rock stable. When it boots into dual channel mode (2 x 2 sticks or 2 x 4 sticks) extemely unstable. "
That means, timings are too tight, or they need a bit more vcore help, or some of the memory stick has failure.
"MSI P7N SLI Platinum - MS-7380 - Bios 2.0 on Vista Ultimate 64-bit - all updated."
That BIOS is not for your board, you should use 1.xx

Internal connectors, front panel audio cennector (10-1 pin AA

i have a Creative Sound Blaster Audigy 2 ZS, and i want to connect me front panel audio connecters to me soundbord, how to do that. i have tryed to download the online manual, but it is corrupt/error so no help there.
can some one help me
question 2, do some one have a manual for Creative Sound Blaster Audigy 2 ZS, or can link one thats work?
Med venlig hilsen / Mit freundlichen Gr?en / Best regards
Allan

Quote from: [LT]Eternalbliss on 21-June-08, 03:43:49
I've just recently had this similar problem. I think the issue in your case is step 3. I believe you should connect the Azalia 10pin wire to your X-fi card, not the mobo.
My problem was that i had connected AC97 10pin wire to my X-fi, after which plugging in my headphones didn't mute my speakers.
That was the problem - works great now! Thanks

No Front Panel Audio

I have an SB Audigy 2 ZS and an Antec Aria case. I would like to use the front panel audio that uses the Intel Standard plug but acording to Creative tech support they don't support it.
The tech basically said that they don't know anything and I have to ask the forum if I want any useful information about the card. I didn't realize Creative tech support was so bad (broke several rules of the trade). But I am here to ask you guys now.
Is there a way to hook up the front panel audio ports to the sound card? My dell uses that white plug to do this. Does anyone know of an adapter that uses the intel plug on one side and the white plug so we can use the fron panel audio and mic jacks?
Thanks.

No-one replied to my similar question here, so I did some googling and posted other places online. Here are some links that should help you in your problem. I have an Antec case myself, and while I have not tried this yet, I think it should work, assuming your audio connector is similar to mine. My Antec P60 case has an Intel-spec AC97 front panel connector, but it also branches into individual leads for non-standard setu
ps.
If you have the correct connector on your Audigy2, this should work. Here are the links I have:
http://www.hardforum.com/showthread.php?t=830840
http://www.driverheaven.net/showthread.php?s=597f798243e2dfcc492d0fce8dd0d&t=5 279&page=&pp=5
http://forums.devhardware.com/t5584/s.html
Someone at Creative Labs should make a sticky out of this procedure and put it in a note at the top of the thread; I bet this gets asked a lot.

MSI P7N SLI Platinum - no POST, how to use Floppy BIOS upgrade

Component Summary:
MOBO: MSI P7N SLI Platinum LGA 775 NVIDIA nForce 750i SLI ATX, BIOS ver 1.1 (A7380NMS V1.1 022508)
MEM: CORSAIR XMS2 DHX 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
CPU: Intel Core 2 Duo E8400 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W, S-spec: SLB9J (E0)
VGA: EVGA 512-P3-N878-AR GeForce 9800 GTX+ SSC Edition 512MB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI
PSU: Thermaltake Purepower W0129RU 600 W ATX12V SLI Ready
Same problem is occurring as outlined in the following threads:
https://forum-en.msi.com/index.php?topic=119615.0
https://forum-en.msi.com/index.php?topic=120513.0
I've carried out the same out-of-box tests indicated in 119615.0 without success.
Question:
Is it possible to force the existing system to boot to the FDD where the BIOS upgrade (v 1.2) would be stored ready for use? If yes, kindly outline the necessary steps to be carried out and please point me to the correct BIOS upgrade link for this configuration. If all else fails, MOBO can be exchanged but if BIOS can be upgraded via this method, I prefer this approach. I don't have access to an alternative CPU, so that approach is far less than ideal. Thanks for your assistance.

Is it possible to force the existing system to boot to the FDD where the BIOS upgrade (v 1.2) would be stored ready for use?
Yes, in theory it is possible to try an AMI BIOS Recovery Flash. However, in case their are other problems that are not visible because of the current problem, it is rather risky. If there is a memory problem or something similar that is currently undetected, the system may crash during flashing and your board will be rendered useless.
Quote
f yes, kindly outline the necessary steps
What you need:
- you need an internal floppy drive (properly connected to the board and 100% intact)
- you need an empty & formated floppy disk (make sure you check it for errors before you use it)
- you need a PS/2 Keyboard
What you have to do:
- download the latest BIOS-Archive file from here:
http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1373
- extract the BIOS File (e.g. A7380NMS.120), rename it to AMIBOOT.ROM [not AMIBOOT.120.ROM] and copy it to the floppy disk
- insert the prepared floppy disk into the floppy drive attached to the P7N SLI Platinum and Clear CMOS with main A/C power cable removed from PSU
- start the system and hit CTRL + HOME to force the system into recovery mode
If that does not work, try a different floppy drive & disk. Don't complain is the system crashes during flashing if the recovery flash starts (system stability is your responsibility).
If you can't get the recovery routine to start and read the AMIBOOT.ROM file from the floppy disk, you need to install a supported processor.

Front Panel Audio - P7N Sli Platinum Question

Similar Messages

Maybe you are looking for