Front panel Printing with A4 Standerd
Easy printing the test reports with the Front panel as per the A4 Standard.
For making the A4 Standard printing needs the option to make Pane A4 Size.
Then we can make easily create the front panel reports easy manner, add Indicator (result ,title, logo, auto signatures etc) in the report and generate the print out.
Developing a GUI on a computer monitor is that much different from printing an A4 (or letter for those americans insisting to use this peculiar standard ), that I think there are not many use cases to force it to the size of a piece of paper.
Alternatively, one could define a printing area, optionally being visible on the front panel and being able to print just that area. So put all controls and indicators you want to be printed in that area, leaving space for GUI elements you don't want to be printed.
The more I think of this the more I like it.
So, on second thought, kudos but preferably for a printing area to be defined by the user.
Greetings from the Netherlands where printers loaded with A4 paper are as common as water runnning from the tap.
(and yes, we all do have taps here ).
Similar Messages
-
Front end printing with control technology problem with Mac platforms
Hello,
We are looking into replacing Host Spool Access method "F: Printing on front end computer" with the newer "front end printing with control technology" but are running into an issue. Our Mac platforms cannot print duplex nor print multiple pages per side using the new technology. We have followed SAP's recommendation to use the POST2 device type but it still won't allow full printing functionality. Has anyone run into this and if so how did you overcome it?
Thanks and Regards,
RichHi Rich,
I've had success getting duplex printing through "front end printing with control technology" with the Mac SAPgui as follows:
In the Mac SAPgui, go to the Preferences window and select Printing (i.e. Preferences -> Desktop -> Printing).
In the "Media sides" pull-down menu, select one of the "two-sided" choices (such as "two-sided-long-edge").
Click the "Save" button at the bottom of the window (near the right hand side.
Print to a Front end printer.
I haven't figured out how to get n-up printing.
/David Rosenberg -
Old Audigy Front Panel Compatible with Audigy 2 ZS c
Is the Audigy Platinum front panel compatible with the Audigy 2 ZS card..
kinTapsry to bump.. but I would like to install the new card... will this work?
-
Front-end printing with control technology
Can anyone elaborate on the new "Front-end printing with control technology" that was released with FEP 15, OSS Note # 821519? Is this something I should be pushing Basis to implement?
Thanks,
JohnHi Rich,
I've had success getting duplex printing through "front end printing with control technology" with the Mac SAPgui as follows:
In the Mac SAPgui, go to the Preferences window and select Printing (i.e. Preferences -> Desktop -> Printing).
In the "Media sides" pull-down menu, select one of the "two-sided" choices (such as "two-sided-long-edge").
Click the "Save" button at the bottom of the window (near the right hand side.
Print to a Front end printer.
I haven't figured out how to get n-up printing.
/David Rosenberg -
hi,
i have a real strange problem and don't know even where to start.
i have a real complex program running on a PC that is connected to my net with a VPN.
every time one of the VIs executed it tells a printer at my location to print the front pannel of this VI.
when running the same program on another PC at the same point i got this strange messsage that the program is attemptint to go to some pdf quick-books files.
the VI is attached.
any ideas will be welcomed
thanks
amose
Attachments:
check for dirt.vi 77 KBOh, I thought the printing was desired. Go to File->VI Properties for the VI you posted. Change the category to Print Options. In the section Print with Execution, you have the automatically print front panel every time VI completes execution checked. Uncheck it. Check to see if you have it checked for any of your subVIs, too.
Message Edited by Matthew Kelton on 12-26-2007 01:36 PM
Attachments:
Print Options.png 19 KB -
Using Front Panel Audio with Fatality Professional
I have a query regarding connections on the Titanium Fatality PCIe.
I have an XFi XtremeMusic PCI card and am considering replacing it with the Titanium Fatality XFi card. A couple of reasons, I like the shrouded enclosure, I like the little XFi LED logo, I want to move away from PCI cards in my system.
But one of the main reasons is to allow me to connect my Intel HD Audio connector to the card so I can use the Headphone/Mic socket on my case. So if anyone has these cards can they confirm that they have an Intel HD Audio connector on them. If so does connecting the headphone to the case socket mute the speakers?
CheersWell, I don't personally have one, but I was under the impression that every X-Fi had one. I know my X-Fi Fatal1ty (original PCI version) included it, and my Recon3D definitely does.
Plus if you check their shop website for the Titanium Fatal1ty Professional than the specs page lists a 2x 5-pin connector for "Intel HD Audio Compatible Front Panel Header" so it most likely does.
I would assume it would mute the speakers only if your case is fully Azalia compliant. By that, I mean the standard (as dictated by Intel) involves the use of two normally-open switches - one each on the headphone and microphone jack - which are closed as a result of plugging something into them. Some cases have these jacks which means it can detect when you plug something in and respond accordingly, but others use cheaper (we're talking differences in cents - not exactly substantial savings, but when you do it thousands of times over it adds up) switchless jacks and simply report them as always plugged in.
Just remember to set up the X-Fi panels to mute the speakers when you plug headphones in, as well as switch the output to headphone mode. You can actually set those two options separately on X-Fis. -
Hey!!
i wana to ask that are there any settings for printing the front panel window??? like describing certain area to print . I actually tried to print it by selecting PRINT WINDOW from files menu but it printed a page without any objects on it??Hi ssddii,
If you select File>>Print from within your VI, it should give you options for printing the front panel. Among these options, you should be prompted to select the VI, choose the portion you want to print (whole front panel, visible portion only, etc), the destination, and set general print settings.
I hope that helps a little,
Lauren
Applications Engineering
National Instruments -
Front panel graph with selectable points
I don't if this can be done, but I was wondering if I can have a graph in the front panel that would graph only the points I select. This is the situation: I'm taking measurements in the program and I want to make a graph with them. The thing is that a don't want a graph with lots of points, I just want to select a point and graph it. When I want to, I select to take a point and graph it, then I'll change the independent variable and then select again one point and graph it, showing a curve of what I have, and so on. I know that for this maybe I'll need to store those single points with an array or something. If anyone can help me, please do so. Thank you.
The data you acquire is received in array form and based on the sample size, you should be able to determine the number of points in the array. Then simply decide which points you want and put them into a second array and plot that array.
-
NI IVI Soft front panel compatibility with IVI-COM drivers
Does IVI soft front panels support IVI-COM instruments drivers ?
For example, I would like to use IVI-COM driver for Tektronix TDS5000 with TestStand...
Jean-Louis SCHRICKE
├ CTA - Certified TestStand Architect (2008 & 2010 & 2014)
├ CTD - Certified TestStand Developer (2004 & 2007)
└ CLD - Certified LabVIEW Developer (2003 & 2005)The IVI soft front panels that ship with the NI IVI Driver Toolset do not support calling IVI-COM drivers. The soft front panels support IVI-C drivers. On Instrument Driver Network there are IVI-C drivers for other Tektronix scopes.
-
Front Panel Connectors with new Motherboard
Hello Lenovo Community, i have just purchased a new mother board(msi h55 e23) and have just installed it into my Lenovo 3000 h210. The only problem with it is the front panel connectors. I don't understand how they're supposed to work. I have a JFP1 and JFP2, yet i'm not sure where the front panel connectors go because im pretty sure they aren't your standard front panel connectors. Is there anyway to get by this without me having to purchase a new case?
http://windowssecrets.com/forums/showthread.php/125942-MSI-Front-Panel-Connector-JFP1
Hi tehota123 and welcome to the Community,
Is this like the problem that you have?
Dave
T430u, x301, x200T, x61T, x61, x32, x41T, x40, U160, ThinkPad Tablet 1838-22R, Z500 touch, Yoga Tab 2 Windows 8.1, Yoga Tablet 3 Pro
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
If someone helped you today, pay it forward. Help Someone Else!
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество -
P35 Platinum front panel audio with Antec P180 case?
God I have a headache after reading all those "front panel audio" threads. Why can't mb's all use the same freaking pinouts!!!!
The case doesn't have a HD front panel.
MB pinouts are:
1. Mic_L (MIC Left Channel)
2. GND
3. MIC_R (MIC Right Channel)
4. PRESENCE#
5. LINEout_R (analog port right channel)
6. MIC_JD (MIC jack detect)
7. Front_JD
8. NC (empty)
9. LINEout_L (analog port left channel)
10. LINEout_JD
Case Front Panel connector is a preconfigured block with pigtails hanging off in case it doesn't match up.
1. MIC Signal
2. MIC Power (MIC BIAS)
3. Ground
4. FPOUT-R (front right)
5. FPOUT-L (front left)
6. RET-R (rear right)
7. RET-R (rear left)
glaring differences are the ground and the MIC connectors.
How do I connect these? I don't want to fry anything.
Thanks.They do have the same pinouts. There are two standards is the reason for two different pinouts. It's just that your MB is Intel HD and your case is AC-97.
For Intel® High Definition Front Panel Audio
Pin Signal Name Description
1 PORT 1L Analog Port 1 - left channel (Microphone)
2 GND Ground
3 PORT 1R Analog Port 1 - right channel (Microphone)
4 PRESENCE# Active low signal that signals BIOS that an Intel® HD Audio dongle is connected to the analog header. PRESENCE# = 0 when an Intel® HD Audio dongle is connected
5 PORT 2R Analog Port 2 - right channel (Headphone)
6 SENSE1_RETURN Jack detection return for front panel (JACK1)
7 SENSE_SEND Jack detection sense line from the Intel® HD Audio CODEC jack detection resistor network
8 KEY Connector key
9 PORT 2L Analog Port 2 - left channel (Headphone)
10 SENSE2_RETURN Jack detection return for front panel (JACK2)
For AC-97 Front Panel Audio
Pin Signal Name Description
1 MIC Front panel microphone input signal (biased when supporting stereo microphone)
2 AUD_GND Ground used by analog
3 MIC_BIAS Microphone power / additional MIC input for stereo microphone support
4 AUD_GND Ground used by analog audio circuits
5 FP_OUT_R Right channel audio signal to front panel (headphone drive capable)
6 FP_RETURN_R Right channel audio signal return from front panel (when headphones unplugged)
7 AUD_5V Filtered +5 V used by analog audio circuits
8 KEY No pin
9 FP_OUT_L Left channel audio signal to front panel (headphone drive capable)
10 FP_RETURN_L Left channel audio signal return from front panel (when headphones unplugged) -
No sound front panel audio with newest CMI 9880L driver
So basically I plugged in a headphone the other day on the front panel and noticed the audio jack randomly stopped working. They worked for about 3 years and the last changes I've made was updating the CMI 9880L driver to the newest one on the MSI website for my mainboard( 915P combo), about a month ago. So I thought the problem was the new driver, I went back to the CD that came with the board and installed the audio drivers I had before, It also didnt work!. I went to the hardware manager and clicked on the ROLL BACK driver button and it installed a microsoft driver, this time the front audio jacks DID work, this means is not a hardware problem. What is going on with the new C-MEDIA driver? what should I do to restore sound to the front jacks?
ps. I messed around with the BIOS options(switching between Azalia and AC97) and nothing happened.Quote from: ivon on 26-September-06, 21:14:20
I am quite confused... would appreciate your help.
Well, so was I. A good explanation can be found at
http://www.intel.com/support/motherboards/desktop/sb/cs-015851.htm
The point is, that the same output can be used either for AC-97 front panel audio (what you have on your chassis) or for High Definition Audio (which I've never seen). The board seems to differentiate between these two by means of the PIN #4 (Presence), which you just leave disconnected in your case.
Microphone should use PINs 1, 2 and 3:
1 - Mic In, 2 - Ground, 3 - Mic Power
Audio output should use PINs 5, 6, 9 and 10:
5 - R-Out, 6 - R-RET, 9 - L-Out, 10 - L-RET.
After you'll have connected the PINs to the audio connectors, do not forget to turn off the jack detection in the "Realtek HD Audio Manager" as I described before. -
Front - end print with new access method G - having issues for some users
Hi Gurus,
Recently we have implemented the new access method G for front-end printing. it is working fine for 90% users in our company. but some users having problems in printing to WINDEFAULT using this new method.
Here is the SAP GUI trace file for the error that they are getting.
(Error)(25.09.09 15:42:36.444): CALL METHOD "CreateControl"[DispID=5] OF [#1/0x0AE31790/1/{83658045-6571-3232-7082-797884697868}]
#0: LONG "101"
#1: STRING "SAPFPRINT.sapfprintCtrl.1"
#2: LONG "0"
#3: LONG "10"
IDispatch::Invoke raised exceptionException occurred
(Error) :
(Error) : ****************************ERROR OCCURED IN MODULE: [{83658045-6571-3232-7082-797884697868}]******************************************************************************************************
(Error) : PROGRAM_ID |MODULE_NAME |METHOD_NAME |ERROR DESCRIPTION |VERSION |GUI VERSION |MODULE_PATH |
(Error) : *****************************************************************************************************************************************************************************************************
(Error) : {83658045-6571-3232-7082-797884697868} |Class name not found |CreateControl |Create control failed |Version info not found |Gui Version not found |Module doesnot exist |
(Error) : *****************************************************************************************************************************************************************************************************
(Error) :
(Error) : Exception fire by :SAP Frontend Server
(Error) : Exception info:Create control failed
(Error) : Exception code:65535
Did any one face this error? what could be the resolution?
We are already on SAP GUI 710 patch level 11
DISP+Work : 229
Appreciate your answers
Thanks,
SriniUsually this means, that some necessary controls are not properly registered in the registry and hence can't be found. You may solve that by removing the SAPGUI from the PC completely, booting the machine and reinstall the GUI.
Markus -
Front panel locks with event structure loop and another while loop
Hi,
Why is the front panel locking after changing the value of the "boolean switch" twice? This problem disappears if I uncheck the "lock front panel" option in the event case. However I don't understand why that is the case since the event structure loop has already finished executing.
thanksDo you really want the event handling to stop after detecting the first event? If so then as Christian says the event structure will cause the front panel to lock. What you can do is dynamically register and unregister the events. You right click on the event structure and enable "Show Dynamic Event Terminals" Then you can programatically register and unregister events.
Here is your vi modified to do that.
Edit: Just in case - right click on the control and create a reference. When selecting the source of the event in the structure look under the dynamic section.
=====================
LabVIEW 2012
Attachments:
event structure test.vi 13 KB -
LV 6.02 (or 6.1)
NT 4.0
I have a vi that the front panel includes all the information I need to print except that it is on different pages of a tab control to conserve screen space. I was attempting to programatically cycle the value of the tab control in a For loop and invoke the Print Panel to Printer method to print 7 pages of the front panel, each with a different tab page selected. The printouts were excellent quality but beginning with the second consecutive Print Panel to Printer method the on screen front panel image of the VI being printed would become jumbled (sometimes, by the time 7 printings were done, the entire front panel image would disappe
ar and a bitmap of the desktop or underlying windows would be visible in the VI's panel frame) yet the subsequent Print Panel to Printer methods continued to print the panel as they should appear. The visible front panel graphics would never return to normal and the only solution was to close the vi (in the dev system) or exe (compiled) and re-launch. I tried a lot of things (like hiding the panel to print before printing and showing it after printing) with no luck. It appears that two or more of these consecutive invoke methods caused the problem regardless of whether the tabs were cycling, or even if there was no tab control and much fewer controls on the panel to be printed than normal. I also had the same problem with LV 6.1.
Finally, I was forced to switch to the report generation toolkit vi's, I cycle through the tab pages and use the Append Front Panel Image to Report.vi to append each image to the report. This is faster and control returns to my program quicker but I a
m unhappy with the printed quality of the graphics of the front panels. They are not as high of resolution as those generated via the Print Panel to Printer method.
Any suggestions?You might try changing the way the VI is printed by going to tools >> options >> printing. Try the postscript and bitmap settings.
Jeremy
Maybe you are looking for
-
I'm looking for a simple DJ app
Hi Folks, I hope this is the best place for this question! I'm looking for a simple App that will allow me to add music on the fly to a playing playlist. iTunes DJ does most of what I want but doesn't allow me to drag and drop order or remove songs.
-
Can't redownload and open an App
I Was updating my Instagram app when my phone lost battery. I charged up back up but them I realized Instagram had been deleted. When I went to the App Store, I wasn't given the option to redownload it but rather "Open" I clicked on open but nothing
-
i'm trying to connect my MacBook Air to a second monitor... I am using the VGA Thunderbolt adapter. It won't flip to the second screen... any suggestions?
-
Hi, I need to call WSDL which has 2 operations. I need to pass default xml payload to operation 1 and the response I get, has to be passed to invoke operation 2. I have created 2 business services and after I create a proxy service : How to pass defa
-
Junit - test for exception problem
I'm trying to test if an exception is being thrown (when one is expected) I get this error (when I shouldn't): java.lang.AssertionError: Expected exception: exception.OutOfRangeException The method being tested: public void setScore ( int score ) thr