Front Panel USB Power

MSI P4M900M2-L, 945GCM5, G31M-F.
Does anyone know how to solve the problem when using Internal card reader + Bluetooth device on this motheroard, the Bluetooth can function normaly but card reader can't, when only disable bluetooth then the card reader can funtion. Both devices are plug in the motherboard JUSB 1 Slot (Front Panel). When plug in a USB Flash Drive and a External Harddisk to the front panel usb at the same time, the USB Flash can work but the Extrnal Harddisk can't.
Any solution for this? Is it the JUSB slot cant produce enough power?
Thank you

The Bluetooth and Card Reader are 2 in 1 device that using a slot in Motherboard (JUSB), after login to windows, the bluetooth can function but when insert flash card the system cannot detect the card but when disable the bluetooth then the system can detect the flash card.
The Front Panel USB problem is when USB Flash Drive and External Harddisk using Front Panel USB slot, only the USB Flash can detect. (With or without card reader also same problem)
These problem seems like lack of power supply from motherboard and only allow 1 device run at the same time, although trying to change Ram, power Supply, Processor but the problem is the same. Customer claim that the card reader can run smoothly in Gigabyte and Intel motherboard, and dont know why these 3 model MSI 7255, 7267, 7345 facing the same problem.
What is the best solution to produce more or stable power or to allow these device run properly?

Similar Messages

Front panel USB - Where to hook up?

I've just put together a system using the 845GE Max M/B. I would like to make use of the front panel USB ports on the case, but can't figure where to plug them in. I'm using the USB 2 card, and there's another USB jack on the M/b...
Any ideas?
Thanks,
Wedge

Looks to me like JUSB1 or JUSB2. It's in the manual.

Z87-G43 Board Front panel USB Problem

I have installed the board and windows 7 64bit
Updated the Bios and checked everything I could. I do NOT get the connect tones from anything I connect to the front panel USB ports. I have used 2 (KNOWN GOOD, works on other machines) connector sets with 2 ports each, and ALL of the ports have the same symptoms. All of the usb devices have the connect tones when inserted to any of the rear ports. I have not tried the USB3 port for the front because I do not have the wiring and related header connector. My phone, (Samsung GS4) when connected to the rear ports always opens an explorer window showing the Ext SDCard and the Internal memory. when I connect to any of the front panel ports, no sound, no pop-up of explorer, but I do see the device when I manually open explorer and can open the connection manually.
I am at a loss as to what is not right and how I can make it work correctly. If anyone can give me any information to correct this, I'd be very grateful. (Tech Support was no help)
Thank you, and Aloha From Hawaii!

Thank you for your reply.
I have an older Antec Case and I have tried a brand new front panel connector I got from Frys and it acts the same Way. the only difference is that the connector is a one piece assembly that connects directly to the mobo header pins. the one in the case has individual pin connectors. both systems end up with the same scenario. When I plug in a thumb drive, there is no connect or disconnect sound and I still can manually open explorer and access the thumb drive or my phone but nothing pops up to signify any port access.BTW, I am a systems engineer and have spent the last 13 years building machines for a transportation company (bus) My previous board in the same case used the front panel connection and it worked just fine, but since the board died and was only supportive of XP I decided to upgrade to Win 7 64bit and have 16gb ram. All the rear connectors work just fine, but I need all of them so have to use the front panel connection for phone, and thumb drive access. I suspect the mobo has a design problem. The tech support person had no suggestion to correct this problem too! :<(

Hp p6367c front panel usb ports: how do I access these?

There is a button in front along the side that I assume is supposed to open the expansion bay and provide access to front panel usb ports, but nothing happens when I press this button.

Please look the upgrade and service manual page 13. You will notice the DVD drive, the empty 2nd CD/DVD bay, maybe the pocket drive (if so equipped). Below that is the mystery USB ports, and audio ports.
The panel likely has a small tab, and the access panel flips up, or slides up/down. Without knowing the exact face plate design, it's difficult to know. But if you look at the manual, the mystery will be exposed.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Problem with front panel USB connector

Motherboard: MS-6750
I have a problem with my front panel USB connector JUSB2 not working.
I have checked the connection to be sure that it is oriented correctly.
I also made sure that it was enabled in the BIOS.
Still no luck. There is not any voltage on this either.
I see a jumper or pin labeled JGS1 just below the JDLED1...do not know what this is and cannot find it in the manual.
Any ideas on what this is and how I might trouble shoot the USB connector?

Which 6570 MB do you have, if its the K7N2 Delta 2 Platinum and came with the Dled bracket try plugging that into that port on the mainboard and see if those usb ports work as it could be the usb hub itself not working on the front. Hope this helps Dok

Z87-G45 front panel USB is SLOW

Ive had this computer running for about a year and all of a sudden it is SLOW via the front panel USB connections. The 3.0 port transfers at about 4-8mbs and the 2.0 about the same.
It use to fly through transfers with the 3.0 up in the 60-80 range.
This just happened overnight and not sure what to try to fix it.
Id rather not do a system restore.

Are you using Windows 8.1 ??
did you check if REAR USB 3.0 works ok??

Front panel USB connection to MB 990fxagd80v2

Hi Gents, new member here with some issues on me last build. I assemble my families computers , about one every 5 years. Other than that I am not hot in computers. So when I get into a build I have some homework and studying to do, and some glitches. At this moment my newest machine is up and running Win 7 with a few loss ends. My case is an USB 2.0 era with 2 ports in the front bottom behind a little door. Each USB cable has 3 wires ending in a flat 3 pin female plug. The motherboard has 2 USB male ports, 9 pins each, one coded blue the other red each one has an alignment notch. This MB came with a sack of M-connectors to be an easy transition between the front panel plugs and the Motherboard, so, 2 of the M-connectors are red and blue, and have alignment lugs that appear to be made for the USB ports on the MB. The problem is they do not fit. While I am gentle and careful I don't believe they fit. I have other front panel issues I'll save for another time. My Gazelle case seems to use different nomenclature than the motherboard. But the USBs are the issue now, anyone have some light on this subject? I would also like to convert one of the front USBs to 3.0.

"Each USB cable has 3 wires ending in a flat 3 pin female plug."
That can't be right as USB are 4 wire, red, white, green, black. Connectors are 5 or 10 pin plugs with no connection on the 5th pin not used on both types & 9 being the key on the 10 pin plug.
"I'm not sure is I have a variation from the standard MB or what..."
Any connectors, MB headers are standard throughout the industry therefore they will be the same from all manufacturers.
"or is the connection does not use m-connectors"
You should not need m-connector for USB anyway. m-connector was introduced mainly for front panel connections that had individual wires for each LED, switches and such. The set in the pic I show is from old P35 MB.
Can you post a photo(s) of the case connectors you have?
See here how to add photo's: https://forum-en.msi.com/index.php?topic=90789.0
Personally I use Photobucket to host my pics.
M-connectors for USB should be clearly marked as such if the MB even came with any for USB. Over the years they have eliminated some and I think the ones for USB were eliminated.
USB plug:

Connecting Front Panel USB & the option Bluetooth bracket!! HELP

Is there anyway to connect both of these modules at the same times.
According to the manual they both use the JUSB1 connector
Does this mean they have to be exchanged everytime you want to use either one?
I am using a MSI KT4 FISR motherboard

the JBT1 is for the Blue Tooth connector that you dont have, it is not for USB or the Dbracket. If you have 2 USB ports in the front of your computer and they are hooked into the JUSB1 connector on the mainboard than you have six USB ports in including the four iin the rear of your computer. Six is the maximum you can have unless you add on additional hardware. If you want to connect the D Bracket than you will have to disconnect the two USB ports in the front of the computer and all six USB ports will be in the rear of the computer.
Hope that clears it up.

FRONT PANEL USB 3 PORTS NOT WORKING.

I have just had a new ASROCK motherboard fitted to my HP Pavilion base unit as it failed after only eighteen months & even though everything is connected correctly my USB devices are not detected when plugged in. The USB 3 ports are the original HP Pavillion ports & cable configuration & plugged into the new ASROCK board.
Specs:-
ASROCK Motherboard: H61M-DG3/USB3. http://www.asrock.com/mb/Intel/H61M-DG3USB3/?cat=Specif...
HP Pavilion 500-081ea base unit: http://support.hp.com/gb-en/product/HP-Pavilion-500-000...
I running Windows 8.1 Pro 64 bit.
Can anyone please help?

Those should be fixed with a chipset driver, which is packaged in the HP graphics driver. Did you install that yet? Don‘t do express install, but rather the custom install and check everything.

To connect a soundblaster audigy 2 ZS to a DELL dimension 8400 front panel headphone/USB jac

Open your case and look at the your front panel USB and Headphone jacks.... look for a black cable and follow it with your fingers until you get to the end. Its should be plugged into your MOBO in a white socket. Carefully unplug it and plug it into a white socket on the top of your AUDIGY. The cable is barely long enough and you might have to mess with it to get it to reach........ that's it!!!!!!!! You can now use your front panel Headphone and USB jacks with your AUDIGY!!!!!!!!!!!!!!!!!!!!!!!!!!!!
:::::::::NOTE::::::::::::
Some older Audigy ZS's might not have the white plug.............Message Edited by MetalFloyd99 on 08-05-2005 08:2 AM

Open your case and look at the your front panel USB and Headphone jacks.... look for a black cable and follow it with your fingers until you get to the end. Its should be plugged into your MOBO in a white socket. Carefully unplug it and plug it into a white socket on the top of your AUDIGY. The cable is barely long enough and you might have to mess with it to get it to reach........ that's it!!!!!!!! You can now use your front panel Headphone and USB jacks with your AUDIGY!!!!!!!!!!!!!!!!!!!!!!!!!!!!
:::::::::NOTE::::::::::::
Some older Audigy ZS's might not have the white plug.............Message Edited by MetalFloyd99 on 08-05-2005 08:2 AM

Z77-G41 USB power always on

I have an annoying issue with a G41. I have the memory card reader connected to one of the USB headers and it has the LED on the reader always illuminated, even when the system is powered on. Checked through entire BIOS and no option to turn that off.
Any ideas? TIA.

Quote from: SynchronicBoost on 22-July-13, 08:23:56
Sorry guys, I meant when powered off. I've tried both JUSB1 and JUSB2. Both with the same result.
Another thing you can try. Plug the card reader into JUSB2 and then in BIOS see that EUp 2013 is enabled, that should shut off power to all USB except for JUSB1. I didn't open my case and change my front panel USB from JUSB1 to another header but I did test the I/O USB and with EUp 2013 disabled there was power to rear USB and when EUP 2013 enabled no power to rear USB.
Only use JUSB1 for front panel if you are using it to charge batteries in other devices such as iPhones, Nooks or whatever or for KB when using standby/sleep states to wake up as it has power at all times, PC on or off, EUP 2013 enabled or disabled. I'll give it a try later today (if I feel like doing so ) to test on JUSB2 or JUSB3 and see if results are same as test on rear panel USB.

Z97g43 connect front panel audio to computer case

I have z97g43.
Front panel audio computer case to mainboard not work.
i have connect:
JAUD1
mainboard chassis ( all pin available connected )
mic_L mic_L
mic_r mic_power
headphone_r headphone_r
headphone_L headphone_L
ground ground
not connect:
Sense send
mic detenction
headphone detenction
what is the right schematic connect?
thanks

What case do you have? If it is an older case with AC97 audio then you would need to purchase something like one of these: http://www.amazon.com/s/?ie=UTF8&keywords=hd+audio+front+panel&tag=googhydr-20&index=electronics&hvadid=54539991636&hvpos=1t2&hvexid=&hvnetw=g&hvrand=11069445173547096755&hvpone=&hvptwo=&hvqmt=b&hvdev=c&ref=pd_sl_2w99a9udvo_b
I simply got me an inexpensive case for my last upgrade since I also needed front panel USB 3 and up to date card reader in addition to the HD audio. My case was only $10 more (free shipping at time of purchase ) than the front panel module I needed so I got the new case you see in my signature instead.

MSI P67A-GD65 - Front panel connections and sli A NO GO!

I have issues with this board and two gtx580 cards in sli, because If I plug the front panel connectors (power, reset, power led, hdd), the bottom card won't fit.
The issue was already found here too: http://hardforum.com/showpost.php?p=1036689234&postcount=81
Any solution from MSI.

That's not a problem for me; as the cables are plenty long. In regards to cable length the position is actually reasonable (though higher up on the same edge would address both issues). I've used at least one mb that had the connector about as far away as possible from the front connectors (it wasn't an msi - the last msi board I used was a K-3 which was really nice; still use it in my Dad's computer). Oh well I hope MSI respond to my ticket; as well as the other fellow; if nothing else maybe in the future they will address the issue.
Quote from: Bernhard on 21-March-11, 04:52:00
The MSI design alone is not the only problem. The case designers also leave the geader cables shorter than desired. I have no problem with my CM 690, but the other cases just seem to have cables that are about 10cm too short.
One solution I have employed is to route those cables under the board, diagonally, as the cable thickness is just less than the standoff heights. Thus, lay the cable in the case before inserting the MB. That way at least they won't get in the way of the GPU cards.

Can I upgrade my e9150t front panel 2 usb from 2.0 to 3.0?

I have an e9150t about 5 or so years old. I just added a USB 3.0 card to it. Can I somehow upgrade or swap out the front panel top left 2 usb slots with 3.0?
Thanks

Hi,
I think this is just a DIY (do it yourself) job and you can do what ever you want after warranty period.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

NI DC Power Soft Front Panel Error - 200247

Hello All,
I am having trouble opening the ni DC power soft front panel. The error message I repeatedly am seeing is below:
When I try to run the vi mentioned in the error above, the same error occurs:
How can I go about getting my soft front panel to work? I have been using the DC power API to execute tests over the past week using the example VI's, but am at a point where the soft front panel would be very helpful to my workflow.
I am using the following:
NI PXIe-4139 SMU
NI PXIe-1082 Chassis
NI PXIe-8360 Controller
Windows 7 64bit
Labview 14
MAX 14.5.0f0
DC Power 14.2
I have tried running the soft front panel using clean installs of DC Power 14.1 and 14.2 and see the same error message. I have uninstalled the other modular instrument driver packages on my computer, NI-Fgen and NI-Scope, reinstalled DC Power, and still I see the error message. It could be that I am not uninstalling these software packages 100% correctly (I use the windows add/remove to NI Remove software dialog process....)
I appreciate any help getting this DC Power soft front panel working.
Thank You,
Andrew Goett

Hi Andrew,
Can you possibly give me a MAX technical report for your system? The instructions can be found here. Use Method 1.
Also, can you check which version of niModInst.dll you have on your system? This file can be found here: <Program Files>\IVI Foundation\IVI\Bin\niModInst.dll
Right-click on the file, select Properties, and then click on the Details tab. The information I need is the "Project version" field. See the image below:
In addition to the MAX report, could you send me a ZIP file of the contents of this folder: <Program Files>\National Instruments\Shared\niModInst
I've attached a simple program (NI-ModInst Code.vi) to test if NI-ModInst is failing across the board or if it only is failing to identify NI-DCPower devices. Open the program, select a driver that you have installed on your system, and run the program. The code should tell you the number of devices you have in the system that are associated with that driver, as well as list out the model numbers for those devices. This list will include simulated devices. Test the code with various drivers in your system to see if you get the same error.
Let me know how this works out.

Front Panel USB Power

Similar Messages

Maybe you are looking for