Frozen startup screen with apple and spining cirlce. BRAND NEW FROM APPLE!
i just bought a new imac today from chadstone apple store and i tried installing one of the grey discs but halfway through installation i stopped it coz i realised i already had it on the computer. then it gave me option to restart or shutdown, i clicked restart but then it froze on the screen - GREY APPLE AND SPINNING SMALL GREY CIRCLE!
WHAT DO I DO?
{quote}i tried installing one of the grey discs but halfway through installation i stopped it coz i realised i already had it on the computer. {quote}
I think you hit the nail on the head right here. Put the restore disk in and restart holding down the C key and install it without canceling.
Similar Messages
-
MacBook Pro won't get off startup screen with apple logo. Help?
Could someone please tell me how I can get my macbook to get off that stupid startup screen with the apple logo? It won't go past that screen and boot properly. I have tried reinstalling OS X didn't work. I tried running a disk utility test and no errors where found. I don't have the time machine thingy so I couldn't try that. Is there anything else I can do before taking it to Apple and l
paying hundreds of dollars???
thanks in advance!!!Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Startup screen with apple logo and grey loading bar, then unexpectedly shuts down
Hey, I have a MacBook Pro from 2010 I believe with iOS Maverick installed. (MacKeeper is also on there, which I just found out is apparently malware)
So three days ago I was watching Netflix, the image froze, but the audio kept going. Figured my internet was slow, so I waited a little, nothing happened. pressed escape to leave the full screen mode, but nothing happened. None of the keys would do anything, not even the sound or brightness keys. So I did a force shut down by holding down the power button.
I waited a little, then decided to turn it back on. Start up sound played, white screen with grey apple logo and loading gear appeared together with a grey loading bar. I figured that this meant it had to repair something. But after about a minute or two it just went to a black screen/ shut down. I left it off for a day, tried it again, same thing. Next day I tried booting it up while holding the shift key to do the safe boot (I knew it wouldn't work since I already had the grey loading bar anyways), same thing happened.
Any suggestions? (note: I thought I had posted this yesterday, but apparently I didn't even register as a user, weird. So if this gets posted twice, I apologize)If your disk cannot be repaired, your only options are to call the disk dead and order a new one or to try and erase and reformat the disk and try to install a system on it.
The latter is just something you can try - I doubt that it will work.
Boot into your Recovery partition once again and select Disk Utility. You should see your boot volume (usually named "Macintosh HD") in the left column of disks. Select the Erase tab and format the disk using "Mac OS Extended (Journaled)". If the disk will format, then you can go back to the main Recovery screen and try installing OS X.
If that doesn't work - and you'll probably know when trying to format the drive - you'll need a new drive.
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.3, 16GB RAM, 960GB SSD, 27” Apple Thunderbolt Display -
IMac g5 is stuck at white startup screen with apple logo & spinning circle
Hello,
i had a digital copy of os x leopard and i was trying to reinstall it, so i would double click on install mac os x, and it would tell me to restart, i would do this but nothing happened so i had to mount the disk again and double click install mac os x, and it told me to restart again. so i looked up how to install leopard from a dmg file, and it said to restore the dmg to the drive, so i went into disk utility and i put the source as the dmg, and the destination i dragged the imac hdd icon. it finished and i was gonna select the leopard file as my startup disk in system preferences, but that wouldnt run. i then noticed some of the letters were missing on the name of the icons in the dock, so i just restarted the computer, but it got stuck on the white screen. i tried lots of stuff like turning on while holding shift, but it didnt do anything, and i tried with cmd+s and that gave me some black command prompt where i typed/sbin/fsck -fy and that did some stuff and it said my drive was okay, but it still wont start up. What do i do?!?!im trying tiger right now, first i wanna reinstall tiger, than leopard next, you know, one problem at a time. i dunno maybe, heres the readme:
Read Before You Install
Mac OS X
Read this document before you install Mac OS X. It includes information about
supported computers, system requirements, and installing Mac OS X.
For more information about Mac OS X, visit this website:
• www.apple.com/macosx/
For the latest information about using Mac OS X, connect to the Internet and open Mac
Help. To open Mac Help, click the Help menu in the Finder and choose Mac Help.
For information about the support available for this product, see the AppleCare
Software Services and Support Guide included with Mac OS X.
System requirements
You must have a Macintosh computer with:
• a PowerPC G3, G4, or G5 processor
• a DVD drive
• built-in FireWire
• at least 256 MB of RAM
• a built-in display or a display connected to an Apple-supplied video card supported
by your computer
• at least 3 GB of disk space available, or 4 GB if you install the developer tools
If you see a message in the Installer that you do not have enough disk space to install
Mac OS X, you can deselect items to save space. To deselect items, click Custom Install
in the Easy Install panel.
Updating your computer’s firmware
You may need to update your computer’s firmware. It’s best to update the firmware
before installing Mac OS X. If you haven’t started the Mac OS X Installer, check the
Apple Software Updates website to see if there are any firmware updates for your
computer:
• www.apple.com/support/downloads/
If you don’t do this, you may see a message that you need to update your computer’s
firmware when you start the Installer. To update the firmware, you will need to quit the
Installer and restart your computer using your current startup disk, then check the
Software Updates website.
If you have problems with your computer after installing this version of Mac OS X, you
might need to update the firmware even though you did not see a message when you
installed the software. Check the Software Updates website for recent firmware updates
for your computer.
Starting installation
To start installing Mac OS X, insert the Mac OS X Install DVD and double-click the
Install Mac OS X icon:
You can also start installing Mac OS X by inserting the Install DVD and restarting your
computer while holding down the C key, or by selecting the Install DVD as your startup
disk using Startup Disk preferences.
Quitting the Installer
If you need to quit the Installer before you click Install in the Easy Install or Custom
Install pane, choose Quit Installer from the Installer application menu, then click
Startup Disk to select a startup disk for your computer.
If you have already clicked Install, wait until installation finishes.
Advice about hardware compatibility
Installing on a Power Macintosh G3 (Blue and White)
If you have a Power Macintosh G3 (Blue and White) that came with an Apple SCSI hard
disk, do not choose UNIX File System (UFS) as the format for the destination disk.
Installing on a computer with a third-party SCSI card
If you have a third-party SCSI card installed in your computer and you cannot start up
Mac OS X, attach a disk drive or terminator to one of the card’s ports. If you continue
to have problems, try removing the card. Contact the manufacturer of the card for
more information about using the card with Mac OS X.
Installing on a computer with a third-party video card
If you have a third-party video card installed in your computer, you may need to
remove it before you install Mac OS X. Contact the manufacturer of the card for more
information about using the card with Mac OS X.
Advice about installing Mac OS X
Erasing and formatting your disk
When you install Mac OS X, you can erase the destination disk you select. In the “Select
a Destination” pane of the Installer, click the Options button. Select Erase and Install
then choose a format. In most cases, choose Mac OS Extended (Journaled).
Important Do not choose UNIX File System (UFS) unless you need to work with this
format. If you choose UFS, Mac OS 9 and all Mac OS 9 applications must be installed on
a Mac OS Extended format disk to use them with the Classic environment.
To install Mac OS X on the same disk or disk partition as Mac OS 9, the disk must be in
Mac OS Extended format. If it isn’t, quit the Installer and back up your files, then
reformat the disk.
You can also partition your hard disk into several volumes before you install Mac OS X.
In the Installer, choose Utilities > Open Disk Utility and click Partition. Partitioning the
disk erases the entire disk, so be sure to back up your files first.
Installing optional software
Easy Install installs all the software you need to use Mac OS X, but does not install
some additional software. If you want to install this optional software or you don’t
want to install all the software installed using Easy Install, click Custom Install and
select the items you want to install. If you want to install this optional software later,
insert the Mac OS X Install DVD and double-click Optional Installs.
Locating the Installer log
When you install Mac OS X, the Installer saves a log of the installation. To see the log,
open Console (in /Applications/Utilities), click Logs, then click the triangle next to /
var/log and select install.log.
Reinstalling Mac OS X
To reinstall Mac OS X, insert the Mac OS X Install DVD and double-click the Install
Mac OS X icon, then follow the onscreen instructions. When you see the “Select a
Destination” pane, click Options to select how to install Mac OS X:
• Select “Archive and Install” to save your existing system files, user accounts and
their home folders, and existing network settings. The Installer saves files in a
folder named Previous System so that you can copy them to an appropriate location
later. You cannot start up your computer using the Previous System folder.
• Select “Erase and Install” to erase the destination volume and install a new copy of
Mac OS X. If you select this option, you will lose all your files and the software you
have installed on the destination volume, so you may want to back it up first. If you
select this option, you can choose the format for the volume. In most cases, choose
Mac OS Extended (Journaled) from the pop-up menu.
Setting up and connecting to the Internet
If you have an existing Internet service provider (ISP) and you’re installing Mac OS X for
the first time, you need to enter your Internet connection information when installation
finishes. Be sure to have the information available. If you have problems connecting to
the Internet, contact your ISP to make sure you have the correct information.
Advice about using Mac OS X
If you have problems starting up
If you cannot start up your computer, insert the Mac OS X Install DVD and restart your
computer while holding down the C key. Choose, Choose > Open Disk Utility, then
click First Aid to repair your disk.
If you have problems starting up your computer and you have devices connected to
your computer such as FireWire drives, USB printers, or external displays, try
disconnecting them before starting up again.
Upgrading your applications and other software
For best results with Mac OS X, look for versions of your applications that are built for
Mac OS X. Check the Mac OS X website for information about available applications:
• www.apple.com/macosx/
If you cannot find Mac OS X versions, upgrade to the latest Mac OS 9 version to use
with the Mac OS X Classic environment. Check with the manufacturers for the latest
updates.
Using POP email accounts and On My Mac mailboxes in Tiger and Panther
If you have a shared home folder and you access a POP email account using Mail in
both Mac OS X Panther and Mac OS X Tiger, you will not see messages that you retrieve
in one version when you switch to the other.
As an alternative, you can deselect the option to remove copies from the server after
retrieving your messages. To change this option, open the Accounts pane of Mail
preferences and click Advanced.
You will not see messages saved in a mailbox on your computer when you switch from
one version to another. To avoid this problem, use separate home folders for each
version of Mac OS X.
Your IMAP account will synchronize automatically when you switch between Mail in
Tiger and Panther.
© 2005 Apple Computer, Inc. All rights reserved. Apple, the Apple logo, FireWire, Macintosh, Mac OS, and
Power Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
PowerPC is a trademark of International Business Corporation, used under license therefrom.
it says that a imac g5 can work -
ipod 4 is displaying blue frozen screen and black screen with apple logo. I try to turn power off but as soon as it goes out it automatically reboots. Plugged it into the usb port on my mac and it doesnt do anything. It doesnt appear in Itunes. Help?
Let the battery fully darain. After charging for an least an hour try a reset and restore. Use Recovery mode if necessary.
If not successful, then time for an appointment at the Genius Bar of an Apple store. -
I Shut down my Mac by holding in the power button after my iMac froze and now when I try to turn it back it on all I get is the grey screen with Apple loge and the timer and doesn't get any further. I have tried the diagnostic test but nothing was found.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
I was updating my ipad 2 and got it disconnected and its not responding,giving a blank screen with apple logo. when i connect it to itunes then it is giving an error that enter your passcode but the screen is blank how can enter my passcode?
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
Cheers, Tom -
When turning on my mac book pro it displays a screen with apple logo and begins loading a loading bar, after this continues to show loading circle however has been like this all day still no different. Tried turning it on and off however still same!
... then run Disk Utility, Repair Disk.
Also:
Resolve startup issues and perform disk maintenance with Disk ...
Mac troubleshooting FAQ: start-up woes
How To Fix Common Mac Startup Problems
Mac Stalls on Gray Screen at Startup - Troubleshooting Mac Startup ... -
Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data. -
I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur
Reinstall OS X:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Reinstalling Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer. -
Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help
Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support
-
Grey screen with apple and upate bar
I am trying to turn on my apple and all it does is goes to grey screen with apple logo and a update bar under it, it acts like it is updating and then just shuts down after it finishes. I restart it and it does the same thing. HELP!!
Hello rosavoyles,
The article linked below provides information and troubleshooting steps that can help get your Mac to boot properly again.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
Cheers,
Allen -
imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black
Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling -
My macbook pro 2011 shows grey screen with apple logo and want start
i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
Won't turn on white screen with apple logo and spinning disc
Mac book air won't boot up just has a white screen with apple logo and spinning disc have tried all the startup multiple key pushes , I think
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
Maybe you are looking for
-
I have installed itunes 10.7 several times, all goes well. After reeboot, I go to check for updates and it still wants to update to version 10.7! I cant sync to my iphone4 because I get an error message saying I need version 10.6.3 or later. Help
-
How to account for Shipping charge not used during Purchase Process?
A PO was created. PO had purchase item price, tax, freight with shipping and insurance. Goods received. PO invoiced for item pricetaxshipping. However, insurance was not paid for in Freight. Question is how can we return the amount back to Vendor? Th
-
Rejected App no problem with binary
Hi, Apple rejected my binary because they belive there is http streaming in my app but there isn't. Do I need to resubmit the app or can I deal with Apple in the resolution centre? They haven't replied to my response in two days? Please advise. Than
-
Adding symbols to the pulldown menu in FrameMaker 7 and 8
I am attempting to add a Section symbol to the pulldown menu. This symbol does not seem to be listed in the menus.cfg file, but I found the "\xa4" definition in the Character Sets PDF file that comes with FrameMaker. <br /><br />This is the procedure
-
ABAP Programm for calling Proxies
Hi Experts, I was writing a ABAP programm für starting a ABAP proxy. *& Report Z_XI_MAPPING REPORT Z_XI_MAPPING. parameters: PA_WAIT type decimals default 0, PA_LOOP type decimals default 1, PA_EOIO type char1 default 'X',