FTP Setup and Endpoint Configuration

Hi Everyone,
We are testing an FTP site on Windows Server 2008 R2 in Azure. I manage to configure the FTP and all working if I test it locally using its Local IP Address. However, I'm having trouble accessing it outside the network using VIP address. I already allowed
FTP port 21 and port 1035-1040 as I recommend on another blog. I have also configured FTP firewall support in IIS using VIP address. But I can't still access it outside its network. Also, I disabled the windows firewall just to isolate the case.
Do you have any recommendation or literature for this.
Thanks
AJ Luistro
Anthony JD Luistro

If you want to use FTP in Azure VM you need to open ports on VM firewall and on service endpoint.
By default, service endpoint has only port 80 enebled, so you need to add port 21 if you want to use firewall.
Mustafa Toroman

Similar Messages

Ftp - ftpd and firewall configuration for passive connections

I set up ftpd on my imac. Connecting and logging on work ok, but when I try to get a directory listing or xfer or send multiple commands it always locks up, i get a message "421 Service not available, remote server timed out. Connection closed" and I see that the ftpd process for that connection has terminated.
Turning the firewall completely off allows ftpd to work correctly, but I was under the impression that if I check the "FTP Access" box under services, the firewall should CORRECTLY self-configure to allow connections to ftpd. Opening ports 1024-65535 guarantees that ftpd will work with a client's passive connection, but is there a better way?
I tried opening 20 for the data connection and 21 for control, but unless I tell everyone to use an active connection, there is still a long wait before most ftp clients notice that passive isn't working and switch to an active connection, so I would like to avoid that also.

Hi, we use FTPd (with Pure FTPd Manager) on our internal server here. While I'm not a complete expert, I do know that we were able to get passive FTP working only after we got this setup properly.
The main reason we got this was for it's ability to set a default port range for passive FTP to work on. In Pure FTPd Manager, you go to Preferences/Settings and you will see the area to input your passive port range (we use 51000-51100).
Then you just need to forward those ports (on a router) to your FTP server, and/or open those ports on your server firewall.
It sounds like you already have ports 20-21 setup.
Hope this helps!
G5 Dual 2Ghz Mac OS X (10.4) 1.5GB RAM

FTP setup and IP addresses

Hi, I am not real sure on this topic. I have done a search for related topics and only came away more confused. If I set up a mac as a FTP site with its FTP sharing on (or remote login, seeing as how people seem to think this is more secure) and I am behind a firewall, how do I get to that machine?
People have said things like "forward port 21 or 22 to that mac, and people can just go to its IP address" but would they need both the outside IP and the inside IP? Lets say that my outside IP is 1.2.3.4.5.6 and my local IP for that mac is 0.0.0.3.2.1 what would someone put in their browser address bar supposing that the proper port is forwarded?
would this change if I had the remote login on instead of FTP? If so what would that address bar have to read?
Thanks everybody.

The whole point of port forwarding is that no remote user needs to know anything about the 'internal' IP address of your server (in your example, the 0.0.0.3 addresss).
When your router is handling your real-world IP address and using NAT to share it amongst other systems, and a remote user opens a connection to that IP address, the router looks at its configuration to see whether it should forward that connection to an internal machine. If it does, it transparently forwards the connection to whatever machine you've specified. When the server at that address replies, the router automatically translates the traffic so that it appears to come from the public IP address handled by the router rather than the private internal address.
That way remote users only need to know the public IP address and you can control in the router which machine in your network the connection is forwarded to.
The whole port-forwarding thing is completely independent of protocol - it doesn't matter whether you're using FTP, SSH/SFTP, HTTP, SMTP, or any other - they all work the same way, letting you forward connections from the public IP address to an internal server on the private network.
The only issue you need to think about is which ports to forward. FTP is a little trickier than others because it uses multiple ports (which is another advantage of SFTP). Since SFTP runs over SSH you just need to forward port 22 to your server and replace 'ftp://' with 'sftp://' in the URL.

How can we write channels and endpoints configuration in actionscript?

Hi All
              how can we define channelset in actionscript in flex
                just like at my client side application itself not in remote-config.xml
                   var cs:ChannelSet = new ChannelSet();
                 var amf:AMFChannel = new AMFChannel(.................................
                   i dont know how to proceed further
                  could any one please help me

Hi All
              how can we define channelset in actionscript in flex
                just like at my client side application itself not in remote-config.xml
                   var cs:ChannelSet = new ChannelSet();
                 var amf:AMFChannel = new AMFChannel(.................................
                   i dont know how to proceed further
                  could any one please help me

CONCURRENT MANAGER SETUP AND CONFIGURATION REQUIREMENTS IN AN 11I RAC ENVIR

제품 : AOL
작성날짜 : 2004-05-13
PURPOSE
RAC-PCP 구성에 대한 Setup 사항을 기술한 문서입니다.
PCP 구현은 CM의 workload 분산, Failover등을 목적으로 합니다.
Explanation
Failure sceniro 는 다음 3가지로 구분해 볼수 있습니다.
1. The database instance that supports the CP, Applications, and Middle-Tier
processes such as Forms, or iAS can fail.
2. The Database node server that supports the CP, Applications, and Middle-
Tier processes such as Forms, or iAS can fail.
3. The Applications/Middle-Tier server that supports the CP (and Applications)
base can fail.
아래부분은 CM,AP 구성과
CM과 GSM(Global Service Management)과의 관계를 설명하고 있습니다.
The concurrent processing tier can reside on either the Applications, Middle-
Tier, or Database Tier nodes. In a single tier configuration, non PCP
environment, a node failure will impact Concurrent Processing operations do to
any of these failure conditions. In a multi-node configuration the impact of
any these types of failures will be dependent upon what type of failure is
experienced, and how concurrent processing is distributed among the nodes in
the configuration. Parallel Concurrent Processing provides seamless failover
for a Concurrent Processing environment in the event that any of these types of
failures takes place.
In an Applications environment where the database tier utilizes Listener (
server) load balancing is implemented, and in a non-load balanced environment,
there are changes that must be made to the default configuration generated by
Autoconfig so that CP initialization, processing, and PCP functionality are
initiated properly on their respective/assigned nodes. These changes are
described in the next section - Concurrent Manager Setup and Configuration
Requirements in an 11i RAC Environment.
The current Concurrent Processing architecture with Global Service Management
consists of the following processes and communication model, where each process
is responsible for performing a specific set of routines and communicating with
parent and dependent processes.
아래 내용은 PCP환경에서 ICM, FNDSM, IM, Standard Manager의 역활을 설명하고
있습니다.
Internal Concurrent Manager (FNDLIBR process) - Communicates with the Service
Manager.
The Internal Concurrent Manager (ICM) starts, sets the number of active
processes, monitors, and terminates all other concurrent processes through
requests made to the Service Manager, including restarting any failed processes.
The ICM also starts and stops, and restarts the Service Manager for each node.
The ICM will perform process migration during an instance or node failure.
The ICM will be
active on a single node. This is also true in a PCP environment, where the ICM
will be active on at least one node at all times.
Service Manager (FNDSM process) - Communicates with the Internal Concurrent
Manager, Concurrent Manager, and non-Manager Service processes.
The Service Manager (SM) spawns, and terminates manager and service processes (
these could be Forms, or Apache Listeners, Metrics or Reports Server, and any
other process controlled through Generic Service Management). When the ICM
terminates the SM that
resides on the same node with the ICM will also terminate. The SM is ？hained?
to the ICM. The SM will only reinitialize after termination when there is a
function it needs to perform (start, or stop a process), so there may be
periods of time when the SM is not active, and this would be normal. All
processes initialized by the SM
inherit the same environment as the SM. The SM environment is set by APPSORA.
env file, and the gsmstart.sh script. The TWO_TASK used by the SM to connect
to a RAC instance must match the instance_name from GV$INSTANCE. The apps_<sid>
listener must be active on each CP node to support the SM connection to the
local instance. There
should be a Service Manager active on each node where a Concurrent or non-
Manager service process will reside.
Internal Monitor (FNDIMON process) - Communicates with the Internal Concurrent
Manager.
The Internal Monitor (IM) monitors the Internal Concurrent Manager, and
restarts any failed ICM on the local node. During a node failure in a PCP
environment the IM will restart the ICM on a surviving node (multiple ICM's may
be started on multiple nodes, but only the first ICM started will eventually
remain active, all others will gracefully terminate). There should be an
Internal Monitor defined on each node
where the ICM may migrate.
Standard Manager (FNDLIBR process) - Communicates with the Service Manager and
any client application process.
The Standard Manager is a worker process, that initiates, and executes client
requests on behalf of Applications batch, and OLTP clients.
Transaction Manager - Communicates with the Service Manager, and any user
process initiated on behalf of a Forms, or Standard Manager request. See Note:
240818.1 regarding Transaction Manager communication and setup requirements for
RAC.
Concurrent Manager Setup and Configuration Requirements in an 11i RAC
Environment
PCP를 사용하기위한 기본적인 Setup 절차를 설명하고 있습니다.
In order to set up Setup Parallel Concurrent Processing Using AutoConfig with
GSM,
follow the instructions in the 11.5.8 Oracle Applications System Administrators
Guide
under Implementing Parallel Concurrent Processing using the following steps:
1. Applications 11.5.8 and higher is configured to use GSM. Verify the
configuration on each node (see WebIV Note:165041.1).
2. On each cluster node edit the Applications Context file (<SID>.xml), that
resides in APPL_TOP/admin, to set the variable <APPLDCP oa_var="s_appldcp">
ON </APPLDCP>. It is normally set to OFF. This change should be performed
using the Context Editor.
3. Prior to regenerating the configuration, copy the existing tnsnames.ora,
listener.ora and sqlnet.ora files, where they exist, under the 8.0.6 and iAS
ORACLE_HOME locations on the each node to preserve the files (i.e./<some_
directory>/<SID>ora/$ORACLE_HOME/network/admin/<SID>/tnsnames.ora). If any of
the Applications startup scripts that reside in COMMON_TOP/admin/scripts/<SID>
have been modified also copy these to preserve the files.
4. Regenerate the configuration by running adautocfg.sh on each cluster node as
outlined in Note:165195.1.
5. After regenerating the configuration merge any changes back into the
tnsnames.ora, listener.ora and sqlnet.ora files in the network directories,
and the startup scripts in the COMMON_TOP/admin/scripts/<SID> directory.
Each nodes tnsnames.ora file must contain the aliases that exist on all
other nodes in the cluster. When merging tnsnames.ora files ensure that each
node contains all other nodes tnsnames.ora entries. This includes tns
entries for any Applications tier nodes where a concurrent request could be
initiated, or request output to be viewed.
6. In the tnsnames.ora file of each Concurrent Processing node ensure that
there is an alias that matches the instance name from GV$INSTANCE of each
Oracle instance on each RAC node in the cluster. This is required in order
for the SM to establish connectivity to the local node during startup. The
entry for the local node will be the entry that is used for the TWO_TASK in
APPSORA.env (also in the APPS<SID>_<HOSTNAME>.env file referenced in the
Applications Listener [APPS_<SID>] listener.ora file entry "envs='MYAPPSORA=<
some directory>/APPS<SID>_<HOSTNAME>.env)
on each node in the cluster (this is modified in step 12).
7. Verify that the FNDSM_<SID> entry has been added to the listener.ora file
under the 8.0.6 ORACLE_HOME/network/admin/<SID> directory. See WebiV Note:
165041.1 for instructions regarding configuring this entry. NOTE: With the
implementation of GSM the 8.0.6 Applications, and 9.2.0 Database listeners
must be active on all PCP nodes in the cluster during normal operations.
8. AutoConfig will update the database profiles and reset them for the node
from which it was last run. If necessary reset the database profiles back to
their original settings.
9. Ensure that the Applications Listener is active on each node in the cluster
where Concurrent, or Service processes will execute. On each node start the
database and Forms Server processes as required by the configuration that
has been implemented.
10. Navigate to Install > Nodes and ensure that each node is registered. Use
the node name as it appears when executing a nodename?from the Unix prompt on
the server. GSM will add the appropriate services for each node at startup.
11. Navigate to Concurrent > Manager > Define, and set up the primary and
secondary node names for all the concurrent managers according to the
desired configuration for each node workload. The Internal Concurrent
Manager should be defined on the primary PCP node only. When defining the
Internal Monitor for the secondary (target) node(s), make the primary node (
local node) assignment, and assign a secondary node designation to the
Internal Monitor, also assign a standard work shift with one process.
12. Prior to starting the Manager processes it is necessary to edit the APPSORA.
env file on each node in order to specify a TWO_TASK entry that contains
the INSTANCE_NAME parameter for the local nodes Oracle instance, in order
to bind each Manager to the local instance. This should be done regardless
of whether Listener load balancing is configured, as it will ensure the
configuration conforms to the required standards of having the TWO_TASK set
to the instance name of each node as specified in GV$INSTANCE. Start the
Concurrent Processes on their primary node(s). This is the environment
that the Service Manager passes on to each process that it initializes on
behalf of the Internal Concurrent Manager. Also make the same update to
the file referenced by the Applications Listener APPS_<SID> in the
listener.ora entry "envs='MYAPPSORA= <some directory>/APPS<SID>_<HOSTNAME>.
env" on each node.
13. Navigate to Concurrent > Manager > Administer and verify that the Service
Manager and Internal Monitor are activated on the secondary node, and any
other addititional nodes in the cluster. The Internal Monitor should not be
active on the primary cluster node.
14. Stop and restart the Concurrent Manager processes on their primary node(s),
and verify that the managers are starting on their appropriate nodes. On
the target (secondary) node in addition to any defined managers you will
see an FNDSM process (the Service Manager), along with the FNDIMON process (
Internal Monitor).
Reference Documents
Note 241370.1

What is your database version? OS?
We are using VCP suite for Planning Purpose. We are using VCP environment (12.1.3) in Decentralized structure connecting to 3 differect source environment ( consisting 11i and R12). As per the Oracle Note {RAC Configuration Setup For Running MRP Planning, APS Planning, and Data Collection Processes [ID 279156]} we have implemented RAC in our test environment to get better performance.
But after doing all the setups and concurrent programs assignment to different nodes, we are seeing huge performance issue. The Complete Collection which takes generally on an avg 180 mins in Production, is taking more than 6 hours to complete in RAC.
So I would like to get suggestion from this forum, if anyone has implemented RAC in pure VCP (decentralized) environment ? Will there be any improvement if we make our VCP Instance in RAC ?Do you PCP enabled? Can you reproduce the issue when you stop the CM?
Have you reviewed these docs?
Value Chain Planning - VCP - Implementation Notes & White Papers [ID 280052.1]
Concurrent Processing - How To Ensure Load Balancing Of Concurrent Manager Processes In PCP-RAC Configuration [ID 762024.1]
How to Setup and Run Data Collections [ID 145419.1]
12.x - Latest Patches and Installation Requirements for Value Chain Planning (aka APS Advanced Planning & Scheduling) [ID 746824.1]
APSCHECK.sql Provides Information Needed for Diagnosing VCP and GOP Applications Issues [ID 246150.1]
Thanks,
Hussein

Virtex6:Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings

Hello，everyone.
I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
I download .bit file to FPGA and succeed.
When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
and the process is about 68% it fails.
The message below the IMapct is as belows:
done.
PROGRESS_END - End Operation.
Elapsed time =      0 sec.
// *** BATCH CMD : identifyMPM
// *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
'1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
done.
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
INFO:iMPACT - Current time: 2014/3/13 8:48:14
// *** BATCH CMD : Program -p 1
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': Programming device...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time =     23 sec.
Selected part: XCF128X
// *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
// *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
INFO:iMPACT - Current time: 2014/3/13 8:49:32
// *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
'1': Downloading core...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:2492 - '1': Completed downloading core to device.
Current cable speed is set to 6.000 Mhz.
Cable speed is default to 3Mhz or lower for BPI operations.
Current cable speed is set to 3.000 Mhz.
Setting Flash Control Pins ...
Setting Configuration Register ...
Populating BPI common flash interface ...
Common Flash Interface Information Query completed successfully.
INFO:iMPACT - Common Flash Interface Information from Device:
INFO:iMPACT - Verification string: 51 52 59
INFO:iMPACT - Manufacturer ID:        49
INFO:iMPACT - Vendor ID:             01
INFO:iMPACT - Device Code:           18
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x008CE03B.
done.
'1': Erasure completed successfully.
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
Setting Flash Control Pins ...
'1': Flash Programming completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Reading device contents...
done.
'1': Verification completed.
Setting Flash Control Pins ...
Current cable speed is resumed to 6.000 Mhz.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
`Elapsed time =    814 sec.
and i find many people have met the same thing. But they are spartan series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
I have read the status Registers and find there is an over-temperature state
and in Impact i could not readback the registers. It is strange.
I am anxious about this problem and have not solved it yet
What reasons may it be?
Hope for your answer, thank you

Hi~I want to know if you solve the configuration problem for virtex-6?
As I encounter the  same configuration problem, I want to consult  you with some question.
Can I have your email?
gszakacs wrote:
I have measured the VCCINT and find it is 1.0V, not 2.997V;
That is not at all surprising. I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
my Reference board is ML605
That would have been nice to know at the beginning...
It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide. See table 1-27, table 1-33 and the note below it about switch S1.
I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA. Have you tried power-cycling to see if the FPGA boots from the flash?
I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that). That will not only show the bits of the configuration status register, but also describe what each bit means. Among other things you can check the state of the FPGA's configuration logic and the Mode pins.

Configure FTPS sender and reciver communication channel.

Good Morning,
I am reading blog for my FTPS for secure connection:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/964f67ec-0701-0010-bd88-f995abf4e1fc
Please tell me the concept of client and server certificates
server certificate --- how and where to deploy
client certificate -- how and where to deploy
how will FTPS -- XI --FTPS Scenario will work then
Regards

Hi,
Please refer the recent discussion here I have provided the couple of links for step by step process as well as the detail explanation about it'
FTPS setup confusion .
Thanks
Swarup

How to setup and configure NI OPC Server to OMRON PLC (CJ2H model) using FINS Ethernet communication protocol?

Hi,
Could someone help me in the setup and configuration of NI OPC server to OMRON PLC (CJ2H model) using FINS Ethernet communication protocol? I already read some materials available in the web but it uses a different PLC and communication protocol. The OPC server is installed in my laptop and I'm using Windows 8 as my OS. I used a cross over RJ45 LAN cable and connected to the ETN21 module of the PLC. I was able to confirmed the communication of my laptop and PLC by pinging the ip address of the ETN21. I also tried to configure the OPC server based on the documents I just read online. I created a channel, device and tag to the OPC server. By the way, I just need to read the data from the tag I created. Can someone also tell me how to monitor the data on the tag? I hope that you could help me. Thank you in advance.

Good day,
Try following the instructions on the driver’s help, take a look at the attach picture. It should be a good starting point. After the PLC is configured you can use this tutorial (Connect LabVIEW to Any PLC Using OPC » http://www.ni.com/white-paper/7450/en/) for a guide on how to monitor the tags.
I hope this helps
Alejandro | Academic Program Engineer | National Instruments
Attachments:
OPC Server Help.JPG ‏237 KB

Lync 2013 Setup and configure HELP

Hi,
i am having some trouble with my lync 2013 setup. i have configured lync to a stage were all users can connect to lync being inside or outside my network, we can send chats messages to each other but only if we are on the same LAN can we use the video, audio
and app sharing and desktop sharing. also i need to know how do i get my lync to communicate with other companies.
ok here is my setup.
ISP Cisco 877 router with 5 Static ips connects to my TMG 2010 (external Nic) internal nic connects to my LAN. all other devices plug into same LAN my TMG is forwarding ports to my exchange and helpdesk system. i have created all internal and external dns
entries. if i need an egde server were do i place this server.
network details below:
5 X ip: X.X.92.2
internal ip: X.X2.1 /24
please could someone assist me.
Kind Regards
Clemy
Cell : +27 72 864 0529

Hi There,
indeed your TMG Server should be equipped with 32 Network Interfaces as follows :
External
DMZ
Internal
the Lync Edge Server should be equipped with 2 Network Interfaces, usually the Edge server is placed inside a perimeter network which consists in 2 edge firewalls, one External and another one is Internal. please check the following link for detailed information
about the various Edge topology that are supported.
However you can always have a DMZ like your scenario which consists in a single firewall and connect the Edge server ends as follows
one interface to the TMG DMZ interface and one interface to the Internal Interface although this way you will be only protecting traffic from the DMZ interface.
kindly note that in case you chose to implement a secondary firewall take into consideration that the network relation from the the Edge internal interface to the internal LAN via the secondary firewall should be a route relation. since this is only the
supported scenario.
as for the reverse proxy you can still use the existing TMG as a reverse proxy since all published web components are actually located on the lync front-end server located on company LAN.
Regards,
Charbel Hanna
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread

Difference between 'setup' and 'configuration' in Oracle Apps

Hi,
Thank in advance.
I want to know Difference between 'setup' and 'configuration'(Oracle Apps ). Could you provide the details with an example, please?
Regards,
Raghavendra Rao

Business Requirement:-
===============
A company may want to allow all of its employees to make purchases up to $10 without having such purchases approved. Another company may have a business rule that each employee’s approval limit depends on his or her position within the organization.
Question:-
=======
How to reach the above requirement?
Is it thorugh configuration or setup?
It must be through configuration and not set up.
Set up is something like one time.. Configuration can be changed depends on your business needs.
Like if your company wants to increases the limit from 10 to 100$, then change in configuration is needed.
Hope you got the answer.. if you want more explanation, please be specific....

Setup and Configure IM Components SSO and DAS on Replica RMS Node

Dear All,
I was trying the step
Step 5: How to Setup and Configure IM Components SSO and DAS on Replica RMS Node In Multimaster Replication (MMR) with Identity Management (IM) Cluster in High Availability Env
But, at the stage to connect to OID, it is not connecting to the RMS database.
When I checked login through ODM, it is connecting fine. also, ldapbind is also binding fine.
How to solve this ? What will be the issue and where to check it ?
Also, from the RMS, when I am connecting through EM console, I am not getting any output on Infrastructure link to change the passwords. its showing
Identity Management
Error retrieving information of default metadata repository.
Unable to establish secure connection to Oracle Internet Directory Server ldap://devportal.paaf.gov.kw:636/ Base Exception : javax.naming.AuthenticationException: [LDAP: error code 49 - Invalid Credentials]
If there is any experts, pls reply. Because, last time I created a TAR and it took months to resolve and ultimately nothing happened they closed the TAR after some time as I was busy with some other works and not able to proceed with the synchronization.
Thanks in advance,
With Regards,
Sheeja Anil

Rule [ 47 ]: fuser link
~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the fuser symbolic link /sbin/fuser -> /bin/fuser exists or
not. This is required for Suse 8.0 and Suse 9.0.
Test [ PASSED ] :
Not required =~ Exists|Not required
Action:
fuser link exists or not required.
Rule [ 48 ]: orarun package
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the orarun package is installed and if the oracle user
environment need to be reset. This is only required for Suse 8.0 and
Suse 9.0.
Test [ PASSED ] :
Not applicable =~ Not installed|Installed correctly|Not
applicable|Environment reset not required
Action:
orarun is not installed or installed correctly.
Rule [ 49 ]: semmsl
~~~~~~~~~~~~~~~~~~~
Description:
Check if semmsl kernel parameter is 256 or higher. For more details on
how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semmsl kernel parameter is 256 or higher.
Rule [ 50 ]: semmns
~~~~~~~~~~~~~~~~~~~
Description:
Check if semmns kernel parameter is 32000 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semmns kernel parameter is 32000 or higher.
Rule [ 51 ]: semopm
~~~~~~~~~~~~~~~~~~~
Description:
Check if semopm kernel parameter is 100 or higher. For more details on
how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semopm kernel parameter is 100 or higher.
Rule [ 52 ]: semmni
~~~~~~~~~~~~~~~~~~~
Description:
Check if semmni kernel parameter is 142 or higher. For more details on
how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semmni kernel parameter is 142 or higher.
Rule [ 53 ]: shmall
~~~~~~~~~~~~~~~~~~~
Description:
Check if shmall kernel parameter is 2097152 or higher. For more
details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
shmall kernel parameter is 2097152 or higher.
Rule [ 54 ]: shmmax
~~~~~~~~~~~~~~~~~~~
Description:
Check if shmmax kernel parameter is 2147483648 or higher. For more
details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
shmmax kernel parameter is 2147483648 or higher.
Rule [ 55 ]: shmmni
~~~~~~~~~~~~~~~~~~~
Description:
Check if shmmni kernel parameter is 4096 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
shmmni kernel parameter is 4096 or higher.
Rule [ 56 ]: msgmax
~~~~~~~~~~~~~~~~~~~
Description:
Check if msgmax kernel parameter is 8192 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
msgmax kernel parameter is 8192 or higher.
Rule [ 57 ]: msgmnb
~~~~~~~~~~~~~~~~~~~
Description:
Check if msgmnb kernel parameter is 65535 or higher. Refer to Oracle
Application Server 10g Installation Guide 10g - Chapter 4 - Section
4.3.3 Configuring the Kernel Parameters on Linux for more details on
how to configure this.
Test [ PASSED ] :
Adequate = Adequate
Action:
msgmnb kernel parameter is 65535 or higher.
Rule [ 58 ]: msgmni
~~~~~~~~~~~~~~~~~~~
Description:
Check if msgmni kernel parameter is 2878 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
msgmni kernel parameter is 2878 or higher.
Rule [ 59 ]: file-max
~~~~~~~~~~~~~~~~~~~~~
Description:
Check if file-max kernel parameter is 131072 or higher. For more
details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
file-max kernel parameter is 131072 or higher.
Rule [ 60 ]: ip_local_port_range
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if ip_local_port_range kernel parameter is between 10000 and
65000 or higher. For more details on how to configure this parameter,
refer to Oracle Application Server 10.1.2 Installation Guide - Chapter
4 - Section 4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
ip_local_port_range kernel parameter is between 10000 and 65000 or
higher.
Rule [ 61 ]: limit processes
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the limit of max processes is set to 16384 or higher. For
more details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
The limit of max processes is set to 16384 or higher.
Rule [ 62 ]: limit descriptors
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the limit of file descriptors is set to 65536 or higher. For
more details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
The limit of descriptors is set to 65536 or higher.
Rule [ 63 ]: Port 1521
~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if port 1521 is free or not. If port 1521 is used by an Oracle
listener version 10.1.0.2 or later, then the existing listener will be
used by the existing database and the Oracle Application Server 10g
Metadata Repository. The installer will perform this configuration
automatically. If port 1521 is used by an Oracle listener version
earlier than 10.1.0.2, then the existing listener need to be stopped.
After the installation is complete, the new 10.1.0.2 listener can be
configured to listen to the existing (pre 10.1.0.2) databases. If port
1521 is used by non-oracle programs, then this program need to be
configured to listen to ports other than 1521. Refer to Installation
Guide, section 4.4.4 for more details.
Test [ PASSED ] :
TNS Listener 10.1.0.2 or higher is running =~ TNS Listener 10.1.0.2 or
higher is running|Free
Action:
Port 1521 is not used, or is used by TNS*Listener version 9.0.1 or
higher.
Rule [ 64 ]: Environment Variables
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the following environment variables are not set: TNS_ADMIN,
ORA_NLS, and LD_BIND_NOW. In addition, the following environment
variables must not references to any existing Oracle Home: PATH,
CLASSPATH and LD_LIBRARY_PATH.
Test [ FAILED ] :
Has reference to existing Oracle Homes = Properly defined
Action:
Refer to the following table for the necessary action to take:
<PRE>
Return Value          Action
Has reference to existing     Remove any reference to existing
Oracle Homes          Oracle Homes from PATH, CLASSPATH
                    and LD_LIBRARY_PATH.
Some variables are set     Unset TNS_ADMIN, ORA_NLS, and
                    LD_BIND_NOW.
Cannot access /etc/oratab     Grant read permission on
                    /etc/issue to the current user.
</PRE>
Rule [ 67 ]: DNS Lookup
~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the host is properly registered in the DNS.
Test [ FAILED ] :
nslookup IP_address = Host correctly registered in DNS
Action:
Refer to the following table for the necessary action to take:
<PRE>
Return Value          Action
nslookup host.domain     The DNS server failed to resolve the
                    nslookup using host.domain.
nslookup IP_address     The DNS server failed to resolve the
                    nslookup using IP address.
Cannot determine IP address Fix any problem with host IP address.
Cannot access          Grant execute permission on
/usr/bin/nslookup      /usr/bin/nslookup to the current
                    user.
</PRE>
Rule [ 68 ]: /etc/hosts format
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if /etc/hosts file contains a line with "ip_address
fully_qualified_hostname short_hostname".
Test [ PASSED ] :
Contains host.domain = Contains host.domain
Action:
The Fuly Qualified Domain name has been set correctly.
Rule [ 69 ]: Oracle Home length
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check that the path to the Oracle home directory is not longer than
127 characters.
Test [ PASSED ] :
Less than 127 char = Less than 127 char
Action:
Oracle Home directory is not longer than 127 characters.
Rule [ 70 ]: Memory for Dev Kit
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the machine has enough memory to install Developer Kits
install type. The minimum requirements is 256 MB.
Test [ PASSED ] :
Available = Available
Action:
The machine has enough memory to install J2EE & Webcache install type.
Rule [ 71 ]: Memory for BI&Forms
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the machine has enough memory to install Business
Intelligence & Forms install type. The minimum requirements is 1 GB.
Test [ PASSED ] :
Available =~ Available|Install type not available
Action:
The machine has enough memory to install Business Intelligence & Forms
install type.
Rule [ 72 ]: Space for BI&Forms
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the machine has enough disk space to install Business
Intelligence & Forms install type. The minimum requirements is 2 GB.
Test [ PASSED ] :
Available =~ Available|Install type not available
Action:
The machine has enough disk space to install Business Intelligence &
Forms install type.
Rule [ 73 ]: control-center
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the minimum required control-center package version is
installed. For RedHat AS/ES 4.0: control-center-2.8.0-12.
Test [ PASSED ] :
Adequate =~ Adequate|Not required
Action:
The required compat-db package version or higher is installed.
Rule [ 74 ]: xscreensaver
~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the minimum required xscreensaver package version is
installed. For RedHat AS/ES 4.0: xscreensaver-4.18-5.rhel4.2.
Test [ PASSED ] :
Adequate =~ Adequate|Not required
Action:
The required compat-db package version or higher is installed.

Setup and configuration for system monitoring and IT Reporting for Java sys

Hi all,
How to setup and configuration for system monitoring and IT Reporting for Java system ?
How to connect Java system to Solman system?
Regards,
Neni

HI,
What is your OS? You can use SAPCCMSR.exe to monitoring IT Reporting Java system on Solman.
Go to solman rz21 create a csmreg user. and configuration fil for agent. copy configuration fil on usr/sap/ccms/..
Go to comman line cd ../user/sap/xxx/sys/exe/.../ wite SAPCCMSR.00 -R pf=< ...../sys/profile/instans profile> .
You can se agent on rz10 and use this connaction on rz20 to monitoring and IT Reporting Java system on Solman.
I hope this help

Matrix Display – setup and model chart

This time, it’s time for a little repetition – we’ve been noticing a bunch of questions on how to set up Matrix Display (the ability to use several monitors on MSI Gaming notebooks) lately, and we’d like to show you all once more. Basically, it is very simple, but there are differences in how to enable this on different models.
The procedure for the GT series can be found here: http://faenl.msi.com/ftp/Notebook/Guides/How%20to%20setup%20MSI%20Matrix%20Display%20on%20MSI%20GT60%2C%20GT70%20Notebooks.pdf
GS and GE: http://faenl.msi.com/ftp/Notebook/Guides/How%20to%20setup%20MSI%20Matrix%20Display%20on%20MSI%20GS60%2C%20GS70%2C%20GE60%2C%20GE70%20Notebooks.pdf
Worth noting is that different models have different capabilities when it comes to outputting video. Below, you can see which model is capable of what.
GT72/GT70/GT60: Built-in display + 3 external monitors
GS70 + GX series: Built-in display + 2 external monitors OR 3 external monitors
GS60, GE60, GP series: Built-in display + 2 external monitors
Matrix Display is yet another MSI feature that not only helps you with your gaming experience, but also boost your productivity, with a minimum of three monitors supported across the range.

Hi.
I have this laptop MSI Dragon Edition GT70 2OD with Geforce 780M, however it also came with the IntelHD Graphics adapter 4600 (which I think is using shared RAM & CPU).
When I go to surround and PhysX configuration, it shows the Laptop Display connected to the Intel instead of GeForce. Also, when I connect a External Display using the VGA port (laptop came with 3 additional video output ports for multiple display: 1 x VGA + 1 x HDMI + 1 x miniDisplay port), both (laptop display and external display) are connected to the Intel instead of Geforce. But when I change the external display to the miniDisplay port (using the proper VGAXminiDisplay adpater), it shows the external display connected to GeForce but the Laptop Display is still connected at the Intel adapter. This results, when I use multiple display, on low performance on my laptop display (native resolution 1920X1080)...
any idea how can I have the Laptop Display connected to the GeForce instead of the intel.
PS: When I dont use the multidisplay, I get full performance on my laptop display in despite of being "connected" to the Intel graphics display.
Some screenshots for your reference:
System Information (by NVIDIA)
http://imageshack.com/a/img537/9616/Zcs8L7.jpg
NVIDIA CONTROL PANEL "Configure Surround, PhysX" (no external monitor attached)
http://imageshack.com/a/img537/265/mJ76kb.jpg
NVIDIA CONTROL PANEL "Configure Surround, PhysX" (external monitor attached via VGA display port)
http://imageshack.com/a/img537/1335/wTZo7h.jpg
NVIDIA CONTROL PANEL "Configure Surround, PhysX" (external monitor attached via miniDisplay port)
http://imageshack.com/a/img911/9154/zQk8de.jpg
NVIDIA CONTROL PANEL "Manage 3D Settings" (external monitor attached via miniDisplay port)
http://imageshack.com/a/img661/1685/Y1si3t.jpg
NVIDIA CONTROL PANEL "Setup Multiple Displays" (external monitor attached via miniDisplay port)
http://imageshack.com/a/img540/4961/o1CWQy.jpg

FTP Setup on Mac Mini Server

Hello:
First off, I am new to Mac OSX Server and servers in general. I am trying to set up FTP so I friends/family can upload to my server. Here is where I am at...
My server is connected to my Airport. My Airport is the DHCP server, distributing a range of IPs to the devices. I do not have a static IP, but am using dyndns to workaround this. Note that even though FTP services are not working, Web services are.
Created a user on the server
Updated the ACL so the user had permissions to the Share
Enabled FTP service on server
Configured Airport for port forwarding to send to server based on IP
The issue i am having is that when i use a client (filezilla) i get a permission denied error on the share. I can mount the share locally to my mac and edit with no issue. Just not thru FTP.

Thank you for the reply!
I did not have the permissions set up there. I made it so the user i created had group access. Then i still had no luck. The firewall is set up and i have port forwarding to the server on my router set up. Then i found my issue...
On the FTP service, when i set up the share permissions, i forgot select protocol options and go to the FTP tab to enable the service. Once i did that, i was golden.
Thank you for your help again!

How do I use a specific host directory in the ftp setup?

I am reestablishing links in CS4 to my websites after an upgrade from Vista to 7.
I use Go Daddy and the subdirectory capability. I had a difficult time setting up the ftp connection and saw in another posting that the Host directory should be left blank. This indeed worked. The problem is that I want to control access of different designers to different websites that are contained in one hosting account. When I use the correct Host directory in the Site Definition dialogue box as I did with my setup on Vista, I get the error message:
"An FTP error occurred - cannot open remote folder [FileName]/. Access denied. The file may not exist, or there could be a permission problem."
However, the file does exist. I have tried various uses of forward slashes, in front, in back, and both, without success. I'm sure there is an answer.
Any ideas?
Thanks,
Mark

Can you verify that your user account has access to those other accounts? Is this a reseller account where you have accounts under your own or is this a dedicated box or VPS where the accounts can be in different directories? Is this a Windows or Linux box
There's a few things that could be going on, but if it ends up being a permission issue Godaddy will be the only ones who can help with that. But just an example of a path on a Unix/Linux environment, "public_html/". There is no leading slash but there is a trailing slash in the path. If you are connecting to a Windows server it could be slightly different, but my only experience with Windows is in a networked/VPN environment so if that is your case I am sure someone else here can help you out.

FTP Setup and Endpoint Configuration

Similar Messages

Maybe you are looking for