Full programme posted!! unable to read the frequency
my programe reads in off an lvdt transducer through a labjack my programe works up until the LJ stream graph process reads to "scaled data v's seconds" graph.where it graphs a sin wave (amplitude vs time)
for some reason the "freq. amp." analyser won't read the frequency correctly. when i run the programme it outputs a frequency of zero.
note: the amplitude is reading correctly
At the end i am looking to have a point on the x-y graph. it is the the output needed for my project.
note: everything works upuntil the scaled data V'S seconds graph
Attachments:
fullprogramme.vi 450 KB
The subvi that produces the output for the "Scaled Data vs Seconds" is not available from your upload--it appears to be your problem.
I attached a jpeg of a test I ran on the last part of your vi--it should work successfully. The simulated signal correctly produces a point on the X-Y graph for amplitude and frequency which is what you desire I believe. If you can find the problem in "LJstream graph process.vi" the output part should work correctly.
Attachments:
test.jpg 42 KB
Similar Messages
-
my programe reads in off an lvdt transducer through a labjack my programe works up until the LJ stream graph process reads to "scaled data v's seconds" graph.where it graphs a sin wave (amplitude vs time)
for some reason the "freq. amp." analyser won't read the frequency correctly. when i run the programme it outputs a frequency of zero.
note: the amplitude is reading correctly
Attachments:
problem.vi 77 KBYour actual data are not accessible and the sub-VI is missing. If you could re-post your VI with time data saved as default on your graph that would be helpful.
In the mean time ... few comments:
- You are attempting to display Amplitude vs. Frequency on an XY-graph. However your graph "data" are just two scalars representing respectivelly the single value amplitude and the single value frequency. This will only give you one point on your graph.
- What exactly are you trying to display? A set of multiple amplitudes vs.frequencies? The spectrum of your signal? -
Unable to read the frequency from this output sine wave of amplitude VS time
my programe reads through a labjack programe works up until the LJ stream graph process reads to "scaled data v's seconds" graph.where it outputs a sine wave (amplitude vs time)
for some reason the "freq. amp." analyser won't read the frequency correctly. when i run the programme it outputs a frequency of zero.
note: the amplitude is reading correctly
see both programmes attached..................
Attachments:
problem.vi 77 KB
LJstream_graph_processing.vi 46 KBI don't really see the utility of this VI, however, the variable "scan rate", of the "LJstream graph processing", it's an arbitrary value, why?...
What is the idea with these VIs?, tell me more, please.
Bye. -
Unable to read the dictionary of the application or extension...
I had previously installed the HP Color LaserJet 3600 driver from the install CD under Tiger. I recently did an archive and install of Leopard, then ran all the system updates. (Currently at 10.5.5)
When I insert the 3600 CD, though, I get a bunch of jibberish (parts of images, etc.) and a MAC OS X directory. The installer inside that directory attempts to be opened with Script Editor, though, and gives an error: "Unable to read the dictionary of the application or extension because it is not scriptable." followed by "The document 'HP Color LaserJet v5.6.1.069' could not be opened."
Previously this would launch the HP installation program that would install the driver. Now, it's like it's not a recognized program or something. I downloaded the driver from the HP website to try it that way (clj3600MacOSX.dmg) with the same result. The .dmg file opens a disk image with the "HP Color LaserJet v.5.6.1.069" file in it...same result. Cannot open.
I know this program ran fine under Tiger...and a co-worker got it to run after doing an upgrade to Leopard (instead of archive and install.)
When I downloaded the HP 4300 installer dmg, it launches a .mpkg file and Get Info says it's set to open with "Installer (default)". The 3600 file, though is set to open with "Script Editor (default)". I've looked to set it to Installer, but don't know where it is...it's not in Applications or Utilities folder.
I then right clicked on the installer file and selected "Show Package Contents". In the window that was displayed, there was a Contents folder. Inside that folder was a file called "HP Color LaserJet v5.6" with no file extension (Get Info doesn't show an extension either,) but it has a VISE logo. Opening that file launches the VISE installer and performs the setup.
So, by jumping through hoops and getting lucky, I was able to install the driver.
The bigger issue, though, is why the installation CD and/or .dmg file downloaded from HP's website cannot run the installer as usual...why are they set to open with Script Editor as the default application...and how can I fix it so that other disks won't have the same problem?
[I originally posted this in the Printers forum, but it appears it's not a printing problem...it's an OS problem...]Installer.app is in /System/Library/CoreServices/
-
When I start the program I instantly see this message: "Adobe Bridge encountered a problem and is unable to read the cache, please try purging the central cache in cache preferences to correct the situation". I have tried this and it only results in a stalled/locked program. I have tried restarting my machine multiple times and tried reconfiguring how the cache is managed. Do you have anyone who could walk me through each step to correct this problem which just started two days ago. I have owned this program for at least a year now...
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
a screen shot of your settings or of the image could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
My bridge is not working normally and keep given me this message : bridge encountered a problem and is unable to read the cache . Please try purging the central cache in cache preferences to correct the situation
And did you then actually purge the cache?
Please realize that you have given ZERO details.
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
a screen shot of your settings or of the image could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
I have master suite cs6. on mac osx. bridge has been quitting unexpectedly. Also, getting message at start up that states that "bridge encountered a problem and is unable to read the cache. Please try purging the central cache in Cache Preferences to correct the situation" I have purged the cache several times and adjusted settings with no change. I also downloaded the entire suite and installed. Do I need to uninstall all of the programs before installing the suite? There is not an option to install only Bridge from the install package.
Maria,
Topic or subject titles should be clear, pertinent and concise so that individual users can tell at a glance if they can help or not.
That field is not for attempting to fit your entire question in there.
Please keep this in mind next time you post. Thank you. -
Write Back Error The system is unable to read the Write Back Template 'test
Write Back Error The system is unable to read the Write Back Template 'test'. Please contact your system administrator. OK
But, the update button is on.
It did work and now it doesn't... nothing of course that we know of has changed. We got this message when we started and the name of the file was what we put as template name in obiee instead of webmessage name but the update button was off.... now we have update button on and same error.
File is on unix and we have made 777 so it's open to the world.
<?xml version="1.0" encoding="utf-8"?>
<WebMessageTables xmlns:sawm="com.siebel.analytics.web/message/v1">
<WebMessageTable lang="en-us" system="WriteBack" table="D_EXEC_METRIC">
<WebMessage name="test">
<XML>
<writeBack connectionPool="writeback">
<update>UPDATE D_EXEC_METRIC SET EXEC_METRIC_ICON_WID = @{c3}, EXEC_METRIC_COMMENT='@{c7}' WHERE SECTOR_WID=@{c0} AND EXEC_METRIC_WID=@{c2}</update>
</writeBack>
</XML>
</WebMessage>
</WebMessageTable>
</WebMessageTables>
thanks in advance for your help!You're better off searching for an answer to this question in the [OBIEE Forum|http://forums.oracle.com/forums/forum.jspa?forumID=378].
The topic is discussed at least twice a month so there's tons of posts with all the answers you need. Make a forum search for writeback and you'll have your answer.
Cheers,
C. -
Unable to read the freq and amplitude
if you could look at the prog.s attached and if you can explain why i am unable to read the data output from "scalled data vs seconds" into tone measurments.
it must have something to do with the conversion from the cluster of 3 elements to the DBL waveform can anyone see the mistake in the conversion!!Please re-post your VI "problem" with default values saved on both graphs.
Thanks -
Unable to read the Inventory Service Object
Hi,
I got the error message when I startinv.
Errpr code: 603. Unable to read the Inventory Service Object in Novell
eDirectory.
Any one know how to fix it.
ThanksMail,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at
http://support.novell.com.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/ -
Bridge encountered a problem and is unable to read the cache. Please try specifying a new cache location in Cache Preferences to correct the situation.
I have do this again and again and again but Bridge ask me to this each time a start up ??Maria,
Topic or subject titles should be clear, pertinent and concise so that individual users can tell at a glance if they can help or not.
That field is not for attempting to fit your entire question in there.
Please keep this in mind next time you post. Thank you. -
043: Unable to read the Software Rules file
hi,
I have the message "043: Unable to read the Software Rules file " that
appears on workstation object under Inventory tab, my software rule is
activated, their is no other options to activate for this rule, is there
other Nds objects that I need to configure for software scans?
thanks!Dominic,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/ -
Scanner Warning 027 unable to read the sequence ....
we have zen 7 sp1 etc...
some of the workstation inventory logf have the following error :
Scanner Warning 027 unable to read the sequence number from the workstation object
i have deleted the edir object, and wait for recreating and new scan.... but the error exist still.
any ideas to resolve the issue?a part from the log ,
here is a bad workstation
[4/23/08 08:29:40.253] ZENInv - Selector: Selector Yielding for ms0
[4/23/08 08:29:40.253] ZENInv - Selector: Processing 000B5D9B682A_1208327423000_6.STR
[4/23/08 08:29:40.253] ZENInv - Selector: Getting SelectorXMLAgent Lock fordaten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832 7423000_6.STR
[4/23/08 08:29:40.253] ZENInv - Selector: Acquired SelectorXMLAgent Lock fordaten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832 7423000_6.STR
[4/23/08 08:29:40.253] ZENInv - Selector: Getting SynchServiceSelector Lock fordaten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832 7423000_6.STR
[4/23/08 08:29:40.253] ZENInv - Selector: Acquired SynchServiceSelector Lock fordaten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832 7423000_6.STR
[4/23/08 08:29:40.254] ZENInv - Selector: Getting ConverterSelector Lock fordaten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832 7423000_6.STR
[4/23/08 08:29:40.254] ZENInv - Selector: Acquired ConverterSelector Lock fordaten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832 7423000_6.STR
[4/23/08 08:29:40.254] ZENInv - Selector: Opened Filedaten:\ZENworks\Inv\ScanDir\000B5D9B682A_12083 27423000_6.STR
[4/23/08 08:29:40.254] ZENInv - Selector: Checking Length of STR
[4/23/08 08:29:40.254] ZENInv - Selector: HASH of FileName000B5D9B682A_1208327423000_6.STRIS=1218633 352
[4/23/08 08:29:40.254] ZENInv - Selector: HASH INSIDE FileName000B5D9B682A_1208327423000_6.STRIS=1218633 352
[4/23/08 08:29:40.254] ZENInv - Selector: End of File=[EOF]
[4/23/08 08:29:40.254] ZENInv - Selector: Valid EOF Found
[4/23/08 08:29:40.254] ZENInv - Selector: Checking Bitmap of STR
[4/23/08 08:29:40.254] ZENInv - Selector: Checking SectionOffsets of STR
[4/23/08 08:29:40.255] ZENInv - Selector: Checking Identification of STR
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing for [Identification]
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing workStationDN
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing treeName
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing and converting numMACAddress
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing macAddresses
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing typeOfScan
[4/23/08 08:29:40.255] ZENInv - Selector: typeOfScan=DELTA
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing and converting scanTime
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing and converting sequenceNumber
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing serverName
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing and converting StrFileVersion
[4/23/08 08:29:40.255] ZENInv - Selector: Checking StrFileVersion
[4/23/08 08:29:40.255] ZENInv - Selector: ZFD STR Version is=1650
[4/23/08 08:29:40.255] ZENInv - Selector: MIDAS ZFD STR VERSION1650
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing strFileSystemType
[4/23/08 08:29:40.255] ZENInv - Selector: Parsing strFileSystemIdentifier
[4/23/08 08:29:40.255] ZENInv - Selector: Entering isInventoryScannerValid()
[4/23/08 08:29:40.255] ZENInv - Selector: isFile30SP1EP1STR Confirms this file is NOT a 30SP1EP1STR
[4/23/08 08:29:40.255] ZENInv - Selector: isFile30SP1EP1STR Confirms this file is NOT a 30SP1EP1STR
[4/23/08 08:29:40.255] ZENInv - Selector: Updating WSDN To SynchService HashTable
[4/23/08 08:29:40.255] ZENInv - Selector: SynchTable Exists
[4/23/08 08:29:40.255] ZENInv - Selector: Entry Already Present.Will not update SynchTable
[4/23/08 08:29:40.255] ZENInv - Selector: isFile30SP1EP1STR Confirms this file is NOT a 30SP1EP1STR
[4/23/08 08:29:40.255] ZENInv - Selector: Reading NDS ScanNumber
[4/23/08 08:29:40.270] ZENInv - Selector: NDS ScanNumber Read 5
[4/23/08 08:29:40.270] ZENInv - Selector: NDS attrModificationTime Read 1208760260000
[4/23/08 08:29:40.270] ZENInv - Selector: Type of Scan:DELTA
[4/23/08 08:29:40.270] ZENInv - Selector: Transfering to DBDir.
[4/23/08 08:29:40.270] ZENInv - Selector: Getting SelectorStorerDestination Lock for daten:\ZENworks\Inv\ScanDir\DbDir\000B5D9B682A_120 8327423000_6.STR
[4/23/08 08:29:40.270] ZENInv - Selector: SelectorStorerDestination Lock Acquired for daten:\ZENworks\Inv\ScanDir\DbDir\000B5D9B682A_120 8327423000_6.STR
[4/23/08 08:29:40.270] ZENInv - Selector: Hence Transferring : daten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832742 3000_6.STR File to daten:\ZENworks\Inv\ScanDir\DbDir\000B5D9B682A_120 8327423000_6.STR
[4/23/08 08:29:40.270] ZENInv - Selector: Renaming the file daten:\ZENworks\Inv\ScanDir\000B5D9B682A_120832742 3000_6.STRTo daten:\ZENworks\Inv\ScanDir\DbDir\000B5D9B682A_120 8327423000_6.STR
[4/23/08 08:29:40.270] ZENInv - Selector: Unlocked SelectorStorerDestination for daten:\ZENworks\Inv\ScanDir\DbDir\000B5D9B682A_120 8327423000_6.STR
[4/23/08 08:29:40.270] ZENInv - Selector: Modifying Attribute seqNo with 6
[4/23/08 08:29:40.270] ZENInv - Selector: Entering forceFullScanFlag Loop
[4/23/08 08:29:40.287] ZENInv - Selector: Time Taken to Process Delta Scan : 34
[4/23/08 08:29:40.287] ZENInv - Selector: Unlocked SelectorXMLAgent Filedaten:\ZENworks\Inv\ScanDir\000B5D9B682A_12083 27423000_6.STR
[4/23/08 08:29:40.287] ZENInv - Selector: Unlocked ConverterSelector Filedaten:\ZENworks\Inv\ScanDir\000B5D9B682A_12083 27423000_6.STR
[4/23/08 08:29:40.287] ZENInv - Selector: Unlocked SynchServiceSelector Filedaten:\ZENworks\Inv\ScanDir\000B5D9B682A_12083 27423000_6.STR
[4/23/08 08:29:40.287] ZENInv - Selector: Selector Will Now Serialize SynchTable - End of Listing
[4/23/08 08:29:40.287] ZENInv - Selector: Serializing hashTable Todaten:\ZENworks\Inv\ScanDir\stable\STABLE.SER
[4/23/08 08:29:40.289] ZENInv - Selector: Selector finished Serializing the table
[4/23/08 08:29:41.043] ZENInv - Storer: Loading Storer test properties file
[4/23/08 08:29:41.044] ZENInv - Storer: Storer: started storing 000B5D9B682A_1208327423000_6.STR (3878 bytes)
[4/23/08 08:29:41.053] ZENInv - Storer: dn: CN=SFT01314.OU=WS.OU=ZEN.OU=city.o=org tree: org-tree
[4/23/08 08:29:41.053] ZENInv - Storer: tree: org-treewsdn: CN=SFT01314.OU=WS.OU=ZEN.OU=city.o=orgtime: 1208931926000
[4/23/08 08:29:41.053] ZENInv - Storer: Initial WS statusrecord is found
[4/23/08 08:29:41.053] ZENInv - Storer: got the status log
[4/23/08 08:29:41.077] ZENInv - Storer: Could not process 000B5D9B682A_1208327423000_6.STR due to
com.novell.zenworks.desktop.inventory.storer.DataA bsentException: Data Instance Not Found!!Class:Zenworks.ZenDesktopMonitor Operation:Delete Offset:e14 linkoffset:ffffffffffffffff oid:-1
[DeviceID=DesktopMonitor2 Description=Plug und Play-Monitor ManufactureDate=2002 ModelID=SNY08B0 ViewableSize=19.7 NominalSize=21.0 ]
at com.novell.zenworks.desktop.inventory.storer.Objec tInstance.setOID(ObjectInstance.java:339)
at com.novell.zenworks.desktop.inventory.storer.Parse .processOtherSection(Parse.java:1913)
at com.novell.zenworks.desktop.inventory.storer.Parse .parse(Parse.java:4038)
at com.novell.zenworks.desktop.inventory.storer.MainT hread.run(MainThread.java:976)
[4/23/08 08:29:41.080] ZENInv - Storer: Scantype set to -1
[4/23/08 08:29:41.081] ZENInv - Storer: addWSErrorMessage
[4/23/08 08:29:41.097] ZENInv - Status Reporting: Number of records to add are: 0 for DN=CN=SFT01314.OU=WS.OU=ZEN.OU=city.o=org
[4/23/08 08:29:41.113] ZENInv - Status Reporting: Number of modified records are: 1 for DN=CN=SFT01314.OU=WS.OU=ZEN.OU=city.o=org
[4/23/08 08:29:41.113] ZENInv - Status Reporting: Modifying record for DN=CN=SFT01314.OU=WS.OU=ZEN.OU=city.o=org
[4/23/08 08:29:41.113] ZENInv - Status Reporting: Record with time stamp 1208931926000 is found
[4/23/08 08:29:41.164] ZENInv - Storer: cleanUp:Full Scan will be initiated on CN=SFT01314.OU=WS.OU=ZEN.OU=city.o=org
[4/23/08 08:29:41.164] ZENInv - Storer: Unlocking daten:\ZENworks\Inv\ScanDir\DbDir\000B5D9B682A_120 8327423000_6.STR
is there a mechanism, to get the local zenworks logfile up to the server, so i didnt need to have access to the workstation manual?
it looks like, that there are no information in the str file from the workstation, but i didnt have a local logfile yet... :-((
helge -
Scanner(Warning) : 027: Unable to read the sequence number from the Workstation object.
Hi
We are having trouble storing inventory scans from some workstations.
We have a windows ONLY environment, with middle tier servers. (ZEN65SP1,
W2KSP4).
Some workstations are storing fine. The Storer function is working and we
can see the storer functions for the 'good' workstations in the Inventory
service window.
However some workstations can't store to the inventory db, but DO populate
eDir ZENworks inventory 'minimal information' but show "Scanner(Warning) :
027: Unable to read the sequence number from the Workstation object." in
the Scan Status...
The Inventory service window shows no attempt by these workstations - it's
almost as though the scan file is not arriving (though eDir knows/displays
the scan file name)
How does the workstation access the scandir in Windows only/middle tier
environment? Does the scan xml stream get sent to the MT via http and then
on to the scandir via CIFS?
Any suggestions/explanations welcome!!
Many thanks
DavidDavid,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at
http://support.novell.com.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/ -
027: Unable to read the sequence number from the Workstation object
Environment:
NW 6.5 sp4
Zen 6.5 sp1
We had a problem with our inventory server processing .STR files a couple
months ago - had to turn off inv. policies on workstations while we resolved
it. Now it's resolved and we're running inventory again. We have a large
number of workstations reporting this error:
027: Unable to read the sequence number from the Workstation object
They have no data in the DB, although they do have minimal scan info, and
the last scan status date matches that of the sequence number error.
I've seen this sporadically in the past and have been able to resolve it by
initiating a full scan on the individual workstation. However, that does
not seem to be making a difference this time.
Novell's troubleshooting document basically says see if the server's
running, and see if there's data for the workstation in the db. Then call
tech support.
Any other ideas?
~~~Nicoya...Jared wrote:
> Nicoya Helm,
>
>> 027: Unable to read the sequence number from the Workstation object
>
> I am thinking that this can also mean a previous full scan was not
> found. Or maybe the STR file name is bad.
>
> This information is stored here
> HKEY_LOCAL_MACHINE\Software\Novell\Workstation
> Manager\InvScanner\"STRFileName"
The machines I'm troubleshooting have valid formats for their STR names,
but that doesn't necessarily mean they are valid STR sequence numbers.
Does removing the value in the reg key cause the STR file name to be
recreated?
>
> Because imaging is used, it's possible that this information is matching
> on some machines which could cause problems.
I've verified that none of our images contain the c:\zenworks history
folder, and we run a script that cleans up any zenworks items before
sysprep (i.e. makes sure there's no registration info on the
workstations, etc). Our imaging scripts also clear any ZIS info to
avoid any duplication as well, so I don't think imaging would be causing
this.
> I believe 6x also has a hist.ini file like 3x inventory does, you might
> delete the file also.
Good tip about the hist.ini file, I didn't know about that. It does not
solve the sequence number error, but it does seem to force a full scan
of the system and cause the new scan to be stored in the DB, which was
not happening before.
Thanks!
Maybe you are looking for
-
What do I do?
-
Connecting DVI Monitor to the ADC port
I have a G5 with dual video ports. One is an ADC Port and the other is a DVI port. I want to get rid of my Apple display and connect two Dell monitors both of which have a DVI connectors. How do I connect a DVI connector to the ADC port? The DVI to A
-
N97 Freezes when answering a call
Hi Need some help here. My n97 freezes occasionally when answering a call. I can hear the person on the other end and they can hear me too. However the phone freezes with the lock/ unlock still on the screen
-
Minimum permisions required to get Design Console access
Hi, What are the minimum permissions required by User (expect for checking the Design Console checkbox on user profile) to access Design Console in OIM 11g R1 (11.1.1.5.0)? Ofcourse, we donot want to add the user in System Admin group. We just want t
-
Hello Dan: We are using Oracle 9.2.0.2 64-bit on a Sun Solaris 5.8 OS. Back in May 2003, I ran into bug #294612, which had to do with using sdo_geom.sdo_area and sdo_geom.sdo_intersection. I had to ignore the geometries that caused the bug to occur.